Electrospun Cu-doped ZnO nanofibers for H2S sensing

Pure and Cu-doped ZnO nanofibers were synthesized via electrospinning technology. The morphology and structure of the as-synthesized nanofibers were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and Raman spectroscopy. The effects of Cu doping on H₂S sensing properties at low concentration (1-10 ppm) were investigated at 230 °C. The results show that the H₂S sensing properties of ZnO nanofibers are effectively improved by Cu doping: 6 at% Cu-doped ZnO nanofibers show a maximum sensitivity to H₂S gas, and the response to 10 ppm H₂S is one order of magnitude higher than the one of pure ZnO nanofibers.     

Characterization and humidity sensing properties of Bi0.5Na0.5TiO3-Bi0.5K0.5TiO3 powder synthesized by metal-organic decomposition

Bi_0.5Na_0.5TiO₃-Bi_0.5K_0.5TiO₃ (BNT-BKT) powder is synthesized by a metal-organic decomposition method and characterized by field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). A humidity sensor, which is consisted of five pairs of Ag-Pd interdigitated electrodes and an Al₂O₃ ceramic substrate, is fabricated by spin-coating the BNT-BKT powder on the substrate. Good humidity sensing properties such as high response value, short response and recovery times, and small hysteresis are observed in the sensing measurement. The impedance changes more than four orders of magnitude within the whole humidity range from 11% to 95% relative humidity (RH) at 100 Hz. The response time and recovery time are about 20 and 60 s, respectively. The maximum hysteresis is around 4% RH. The results indicate that BNT-BKT powder is of potential applications for fabricating high performance humidity sensors.     

Au-doped WO3-based sensor for NO2 detection at low operating temperature

Pure and Au-doped WO₃ powders for NO₂ gas detection were prepared by a colloidal chemical method, and characterized via X-ray powder diffraction (XRD), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). The NO₂ sensing properties of the sensors based on pure and Au-doped WO₃ powders were investigated by HW-30A gas sensing measurement. The results showed that the gas sensing properties of the doped WO₃ sensors were superior to those of the undoped one. Especially, the 1.0 wt% Au-doped WO₃ sensor possessed larger response, better selectivity, faster response/recovery and better longer term stability to NO₂ than the others at relatively low operating temperature (150 °C).     

Improved selective acetone sensing properties of Co-doped ZnO nanofibers by electrospinning

Pure and Co-doped (0.3 wt%, 0.5 wt%, and 1 wt%) ZnO nanofibers are synthesized by an electrospinning method and followed by calcination. The as-synthesized nanofibers are characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and energy dispersive X-ray (EDX) spectroscopy. Comparing with pure ZnO nanofibers, Co-doped nanofibers exhibit improved acetone sensing properties at 360 °C. The response of 0.5 wt% Co-doped ZnO nanofibers to 100 ppm acetone is about 16, which is 3.5 times larger than that of pure nanofibers (about 4.4). The response and recovery times of 0.5 wt% Co-doped ZnO nanofibers to 100 ppm acetone are about 6 and 4 s, respectively. Moreover, Co-doped ZnO nanofibers can successfully distinguish acetone and ethanol/methanol, even in a complicated ambience. The high response and quick response/recovery are based on the one-dimensional nanostructure of ZnO nanofibers combining with the Co-doping effect. The selectivity is explained by the different optimized operating temperatures of Co-doped ZnO nanofibers to different gases.     

Selective gas sensing response from different loading of Ag in sol-gel mesoporous titania powders

Bare and Ag loaded TiO₂ (0.05, 0.5, and 5.0 mol% Ag) powders prepared by sol-gel process have been used for the detection of ethanol, LPG, acetone and toluene gases. These materials were well characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution TEM (HRTEM), X-ray photoelectron spectroscopy (XPS) and Brunauer-Emmett-Teller (BET) specific surface area analysis techniques. Specific surface area increased with increasing Ag loading in these mesoporous materials. A thorough TEM/HRTEM investigation with X-ray maps of the modified particles shows the extent of TiO₂ surface coverage by Ag nanoparticles. From the comparative study of the sensor response of Ag-TiO₂ powders for various gases, it is observed that each Ag loading resulted in the highest response towards a particular gas or in other words, every gas responded best towards a particular Ag loading of the sensor material, i.e. 0.05 mol% Ag-TiO₂ sensor showed highest response towards ethanol, 0.5 mol% Ag-TiO₂ sensor showed best response towards toluene, whereas, bare TiO₂ proved to be the best sensor for both acetone and LPG gases. This establishes that Ag loading is not required for detection of acetone and LPG gases. On the basis of detailed materials characterization, a mechanism for the gas sensing response of each analyte has been discussed.     

Zeolite-modified WO3 gas sensors – Enhanced detection of NO2

Solid-state metal oxide gas sensors with zeolite overlayers have been developed as a means to improve sensor selectivity. Screen printed tungsten oxide (WO₃) sensors were modified by the addition of acidic and catalytic zeolite layers. The sensors were characterised before and after sensing experiments using X-ray diffraction, energy dispersive X-ray analysis and scanning electron microscopy. The sensors were tested against various gases and gas mixtures to assess their discriminatory behaviour. The results show that the sensors response can be tailored to be selective towards specific target gases by changing the zeolite; for example the H-ZSM-5 sensor gave a response 19 times greater to NO₂ than an unmodified control sensor. It was observed that the WO₃ based gas sensors showed a remarkable selectivity towards NO₂ in a gas mixture. The sensors also showed high levels of stability and sensitivity and have potential to be used in electronic nose technology.     

Nanostructured spinel ZnCo2O4 for the detection of LPG

Nanostrucutred spinel ZnCo₂O₄ (∼26-30 nm) was synthesized by calcining the mixed precursor (consisting of cobalt hydroxyl carbonate and zinc hydroxyl carbonate) in air at 600 °C for 5 h. The mixed precursor was prepared through a low cost and simple co-precipitation/digestion method. The transformation of the mixed precursor into nanostructured spinel ZnCo₂O₄ upon calcinations was confirmed by X-ray diffraction (XRD) measurement, thermogravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS) and high resolution transmission electron microscopy (HRTEM). To demonstrate the potential applicability of ZnCo₂O₄ spinel in the fabrication of gas sensors, its LPG sensing characteristics were systematically investigated. The ZnCo₂O₄ spinel exhibited outstanding gas sensing characteristics such as, higher gas response (∼72-50 ppm LPG gas at 350 °C), response time (∼85-90 s), recovery time (∼75-80 s), excellent repeatability, good selectivity and relatively lower operating temperature (∼350 °C). The experimental results demonstrated that the nanostructured spinel ZnCo₂O₄ is a very promising material for the fabrication of LPG sensors with good sensing characteristics. Plausible LPG sensing mechanism is also discussed.     

Formaldehyde sensing properties of electrospun NiO-doped SnO2 nanofibers

Formaldehyde is a kind of hazardous gases dangerous to human health. Hence, gas sensor is an essential device to monitor formaldehyde in air, especially in indoor ambient. Semiconductor metal oxides are studied as gas-sensing material to detect most of key gases for decade years. For the purpose of actual application and meeting a variety of conditions, diverse additives added into host material are expected to improve the performance of gas sensors. The formaldehyde gas-sensing characteristics of undoped and NiO-doped SnO₂ (NSO) nanofibers synthesized via a simple electrospinning method were investigated in this study. It is noticed that the addition of NiO causes the distortion at the surface of SnO₂ nanofibers, which is responsible to adjust activation energy, grain sizes and chemical states of host material. The sensors fabricated from NSO nanofibers exhibited good formaldehyde sensing properties at operating temperature 200 °C, and the minimum-detection-limit was down to 0.08 ppm. The response time and recovery time of the sensors were about 50 s and 80 s to 10 ppm formaldehyde, respectively. The sensor shows a good long-term stability in 90 days. The simple preparation and excellent properties significantly advance the viability of electrospun nanofibers as gas sensing materials. The sensing mechanisms of NSO nanofibers to formaldehyde were discussed. The results indicated that NSO nanofibers could be used as a candidate to fabricate formaldehyde sensors in practice.     

Highly sensitive and selective LPG sensor based on α-Fe2O3 nanorods

The α-Fe₂O₃ nanorods were successfully synthesized without any templates by calcining the α-FeOOH precursor in air at 300 °C for 2 h and their LPG sensing characteristics were investigated. The α-FeOOH precursor was prepared through a simple and low cost wet chemical route at low temperature (40 °C) using FeSO₄·7H₂O and CH₃COONa as starting materials. The formation of α-FeOOH precursor and its topotactic transformation to α-Fe₂O₃ upon calcination was confirmed by X-ray diffraction measurement (XRD), X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM) analysis. The α-Fe₂O₃ nanorods exhibited outstanding gas sensing characteristics such as, higher gas response (∼1746-50 ppm LPG at 300 °C), extremely rapid response (∼3-4 s), relatively slow recovery (∼8-9 min), excellent repeatability, good selectivity and lower operating temperature (∼300 °C). Furthermore, the α-Fe₂O₃ nanorods are able to detect up to 5 ppm for LPG with reasonable response (∼15) at the operating temperature of 300 °C and they can be reliably used to monitor the concentration of LPG over the range (5-60 ppm). The experimental results clearly demonstrate the potential of using the α-Fe₂O₃ nanorods as sensing material in the fabrication of LPG sensors. Plausible LP G sensing mechanism of the α-Fe₂O₃ nanorods is also discussed.     

Highly sensitive NO2 sensor based on square-like tungsten oxide prepared with hydrothermal treatment

The square-like WO₃ nanosheets were synthesized by hydrothermal treatment of irregular WO₃ nanosheets prepared through acidification of Na₂WO₄·2H₂O. The obtained square-like and irregular WO₃ nanosheets were characterized with field emission scanning electron microscopy, X-ray powder diffraction and transmission electron microscopy. The gas sensing properties of sensors based on as-prepared samples were investigated. The results indicated that both samples exhibited high response to NO₂. The sensor based on square-like WO₃ nanosheets exhibited remarkably enhanced response and faster response/recovery time for NO₂ compared with that based on irregular nanosheets. Especially, the sensor based on square-like WO₃ nanosheets could detect NO₂ down to 40 ppb, which covered environmental standard. A possible reason for the influence of unique structure on the sensing properties of sensors based on square-like WO₃ was proposed.     

Enhanced H2S sensing characteristics of Pt doped SnO2 nanofibers sensors with micro heater

Gas sensors were designed and fabricated using oxide nanofibers as the sensing materials on micro platforms using micromachining technology. Pure and Pt doped SnO₂ nanofibers were prepared by electrospinning and their H₂S gas sensing characteristics were subsequently investigated. The sensing temperatures of 300 and 500 °C could be attained at the heater powers of 36 and 94 mW, respectively, and the sensors showed high and fast responses to H₂S. The responses of 0.08 wt% Pt doped SnO₂ nanofibers to 4-20 ppm H₂S, were 25.9-40.6 times higher than those of pure SnO₂ nanofibers. The gas sensing characteristics were discussed in relation to the catalytic promotion effect of Pt, nano-scale morphology of electrospun nanofibers, and sensor platform using micro heater.     

Structural and gas-sensing properties of CuO-CuxFe3−xO4 nanostructured thin films

Nanocrystalline CuO-Cu_xFe_3−xO₄ thin films were developed using a radio-frequency sputtering method followed by a thermal oxidation process. Thin films were deposited applying two very different conditions by varying the argon pressure and the target-to-substrate distance. Structural, microstructural and gas-sensing characteristics were performed using grazing incidence X-ray diffraction (GXRD), Raman spectroscopy, atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and electrical measurements. Their sensing properties were examined using hydrogen gas in dry synthetic air. The shortest response and recovery times were observed between 280 and 300 °C independently of the deposition conditions.     

Architecture of electrospun carbon nanofibers–hydroxyapatite composite and its application act as a platform in biosensing

A biofunctional hybrid composite was constructed by assembling hydroxyapatite (HA) onto carboxylic group-functionalized carbon nanofibers (FCNFs). The FCNFs was obtained from acid treatment of carbon nanofibers (CNFs) which were synthesized by the combination of electrospinning and thermal treatment processes. The obtained carbon nanofibers–hydroxyapatite composite (FCNFs–HA) was characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and FTIR spectroscopy. Cytochrome c (Cyt c) was successfully immobilized in this three-dimensional FCNFs–HA composite and the electron transfer rate constant (k_s) was evaluated to be 3.66 s⁻¹ according to Laviron's equation. And the surface coverage (Γ*) was estimated to be 8.1 × 10⁻¹⁰ mol cm⁻². Cyt c immobilized in FCNFs–HA composite exhibited a good electrocatalytic activity towards the reduction of hydrogen peroxide (H₂O₂). The catalytic current is linear to the H₂O₂ concentration in the range of 2.0 μM to 8.7 mM (r = 0.9996; n = 28), and the detection limit was 0.3 μM based on the criterion of a signal-to-noise ratio of 3.     

Fabrication of N-type Fe2O3 and P-type LaFeO3 nanobelts by electrospinning and determination of gas-sensing properties

N-type Fe₂O₃ nanobelts and P-type LaFeO₃ nanobelts were prepared by electrospinning. The structure and micro-morphology of the materials were characterized by X-ray diffraction (XRD) and scanning of electron microscopy (SEM). The gas sensing properties of the materials were investigated. The results show that the optimum operating temperature of the gas sensors fabricated from Fe₂O₃ nanobelts is 285 °C, whereas that from LaFeO₃ nanobelts is 170 °C. Under optimum operating temperatures at 500 ppm ethanol, the response of the gas sensors based on these two materials is 4.9 and 8.9, respectively. The response of LaFeO₃-based gas sensors behaves linearly with the ethanol concentration at 10-200 ppm. Sensitivities to different gases were examined, and the results show that LaFeO₃ nanobelts exhibit good selectivity to ethanol, making them promising candidates as practical detectors of ethanol.     

Microstructure control of TiO2 nanotubular films for improved VOC sensing

Porous gas sensing films composed of TiO₂ nanotubes were fabricated for the detection of volatile organic compounds (VOCs), such as alcohol and toluene. In order to control the microstructure of TiO₂ nanotubular films, ball-milling treatments were used to shorten the length of TiO₂ nanotubes and to improve the particle packing density of the films without destroying their tubular morphology and crystal structure. The ball-milling treatment successfully modified the porosity of the gas sensing films by inducing more intimate contacts between nanotubes, as confirmed by scanning electron microscopy (SEM) and mercury porosimetry. The sensor using nanotubes after the ball-milling treatment for 3 h exhibited an improved sensor response and selectivity to toluene (50 ppm) at the operating temperature of 500 °C. However, an extensive ball-milling treatment did not enhance the original sensor response, probably owing to a decrease in the porosity of the film. The results obtained indicated the importance of the microstructure control of sensing layers in terms of particle packing density and porosity for detecting large sized organic gas molecules.     

Plasma enhanced-CVD of undoped and fluorine-doped Co3O4 nanosystems for novel gas sensors

Co₃O₄-based nanosystems were prepared on polycrystalline Al₂O₃ by plasma enhanced-chemical vapor deposition (PE-CVD), at temperatures ranging between 200 and 400 °C. The use of two different precursors, Co(dpm)₂ (dpm = 2,2,6,6-tetramethyl-3,5-heptanedionate) and Co(hfa)₂·TMEDA (hfa = 1,1,1,5,5,5-hexafluoro-2,4-pentanedionate; TMEDA = N,N,N′,N′-tetramethylethylenediamine) enabled the synthesis of undoped and fluorine-doped Co₃O₄ specimens, respectively. A thorough characterization of their properties was performed by glancing incidence X-ray diffraction (GIXRD), atomic force microscopy (AFM), field emission-scanning electron microscopy (FE-SEM), secondary ion mass spectrometry (SIMS) and X-ray photoelectron spectroscopy (XPS). For the first time, the gas sensing properties of such PE-CVD nanosystems were investigated in the detection of ethanol and acetone. The results show an appreciable response improvement upon doping and functional performances directly dependent on the fluorine content in the Co₃O₄ system.     

Room-temperature H2S gas sensing at ppb level by single crystal In2O3 whiskers

In₂O₃ whiskers and bipyramidal nano-crystals were prepared by a carbothermal method. These were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), energy dispersive X-ray analysis (EDX), photoluminescence and Raman spectroscopy. These were studied for application to sensing of H₂S gas. The single crystal whiskers were found to be sensitive to as low as 200 ppb of H₂S gas at room temperature and showed saturation in response at 10 ppm. On the other hand, the films made of bipyramids were less sensitive to H₂S gas and the response was found to be a nearly linear function of concentration in a concentration range of 10–80 ppm.     

C-doped WO3 microtubes assembled by nanoparticles with ultrahigh sensitivity to toluene at low operating temperature

Novel C-doped WO₃ microtubes (MTs) were successfully synthesized by a facile infiltration and calcination process using the cotton fibers as templates. The prepared MTs were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FESEM), N₂ adsorption and desorption measurements and ultraviolet-visible spectroscopy. XPS spectra show the carbon was doped into the lattice of the WO₃ phase, resulting in a decrease of the band gap of the C-doped WO₃ MTs from 2.45 eV to 2.12 eV. Moreover, the WO₃ MTs were assembled by nanoparticles in size of ca. 40 nm and had larger specific surface area (21.3 m²/g) due to existence of meso/macro-pores inside them. At low operating temperature of 90 °C, the gas sensor based on the C-doped WO₃ MTs had a detected limit of 50 ppb to the toluene gas (response of 2.0). The enhancement of toluene sensing performance of C-doped WO₃ MTs was attributed to a larger surface area and higher porosity, which arises from its unique MTs. Furthermore, the band gap reduction and a new intragap band formation for C-doped WO₃ MTs were proposed as the reason for the decrease in optimal operating temperature.     

Preparation and gas sensing properties of pure and doped γ-Fe2O3 by an anhydrous solvent method

Nanocrystalline undoped and Cd-doped γ-Fe₂O₃ powders were synthesized by an anhydrous solvent method and characterized by thermogravimetric analysis (TGA), differential thermal analysis (DTA), X-ray diffraction (XRD) and transmission electron micrograph (TEM). The gas sensitivity measurements indicated that both the undoped (operated at 240 °C) and the 5 mol% Cd-doped γ-Fe₂O₃ sensors (operated at 270 °C) exhibited high response to acetone and ethanol, moderate response to petrol, poor response to liquefied petroleum gas (LPG), H₂ and CO. Furthermore, the 5 mol% Cd-doped γ-Fe₂O₃ sensor presented shorter response and recovery times, better long-time stability, larger response and better selectivity to acetone and ethanol than the undoped sensor. The present undoped and Cd-doped γ-Fe₂O₃ sensors obtained by an anhydrous solvent method were almost insensitive to LPG, while the reported γ-Fe₂O₃ sensors prepared by a hydrous solution method were generally sensitive to LPG, suggesting that the preparation method played a key role in determining the gas sensing properties.     

CdO activated Sn-doped ZnO for highly sensitive, selective and stable formaldehyde sensor

Sn-, Ni-, Fe- and Al-doped ZnO and pure ZnO are prepared by coprecipitation method, and characterized by scanning electron microscope (SEM), energy diffraction spectra (EDS) and X-ray diffraction (XRD). Their formaldehyde gas sensing properties are evaluated and the results show that 2.2 mol% Sn dopant can increase the response of ZnO by more than 2 folds, while other dopants increase little response or even decrease response. Further, CdO is used to activate ZnO based formaldehyde sensing material. It is demonstrated that 10 mol% CdO activated 2.2 mol% Sn-doped ZnO has the highest formaldehyde gas response, with a linear sensitivity of ∼10/ppm at lowered work temperature of 200 °C than 400 °C of pure ZnO, and high selectivity over toluene, CO and NH₃, as well as good stability tested in 1 month.