4-bit multiplexer/demultiplexer chip set for 40-Gbit/s optical communication systems

We have designed and fabricated a low-power 4:1 multiplexer (MUX), 1:4 demultiplexer (DEMUX) and full-clock-rate 1:4 DEMUX with a clock and data recovery (CDR) circuit using undoped-emitter InP-InGaAs HBTs. Our HBTs exhibit an f/sub T/ of approximately 150 GHz and an f/sub max/ of approximately 200 GHz at a collector current density of 50 kA/spl mu/m/sup 2/. In the circuit design, we utilize emitter-coupled logic and current-mode logic series gate flip-flops and optimized the collector current density of each transistor to achieve low-power operation at required high bit rates. Error-free operation at bit rates of up to 50 Gbit/s were confirmed for the 4:1 MUX and 1:4 DEMUX, which dissipates 2.3 and 2.5 W, respectively. In addition, the full-clock-rate 1:4 DEMUX with the CDR achieved 40-Gbit/s error-free operation.     

Simulation and design methodology for a 50-Gb/s multiplexer/demultiplexer package

A 50 Gb/s package for SiGe BiCMOS 4:1 multiplexer and 1:4 demultiplexer targeting SONET OC-768 serial communication systems is introduced in this work. The package was designed to facilitate bit-error-rate tests and constructed with high-speed coaxial connectors, transmission lines on ceramic substrate, ribbon bonds for chip-to-package interconnects, and a metal composite housing. Numerical simulations were conducted to guide the package design, and both small signal measurements and operational tests were performed thereafter to verify the design and modeling concepts. To keep the model structure under the existing computing capability, the simulation was segmented into three sections - coaxial connector to transmission line, transmission line alone, and transmission line to ribbon bond, and then the results were assembled to predict the performance of the entire package. The package was operated up to 50 Gb/s with low degradation to input digital waveforms and free of error.     

A 10-GHz 8-b multiplexer/demultiplexer chip set for the SONETSTS-192 system

An ultrahigh-speed 8-b multiplexer (MUX) and demultiplexer (DMUX) chip set has been developed for the synchronous optical network (SONET) next-generation optical-fiber communication systems, which will require data bit rates of about 10 Gb/s. These ICs were designed using three novel concepts: a tree-type architecture giving reliable operation, a dynamic divider with a wide operating range, and a 50-Ω on-chip transmission line with high-speed pulse propagation. They were fabricated using a 0.5-μm WN_x-gate GaAs MESFET process. The DMUX and MUX operated at up to 10.4 and 11.4 GHz, respectively, both with an adequate phase margin of more than 230°     

50-Gb/s SiGe BiCMOS 4:1 multiplexer and 1:4 demultiplexer for serial communication systems

4:1 multiplexer and 1:4 demultiplexer ICs targeting SONET OC-768 applications are reported. The ICs have been implemented using a 120-GHz-f/sub T/ 0.18-/spl mu/m SiGe BiCMOS process. Both ICs have been packaged to enable bit error rate testing by connecting their serial interfaces. Error-free operation has been achieved for both circuits at data rates beyond 50 Gb/s. At a -3.6-V supply voltage, the multiplexer and demultiplexer dissipate 410 and 430 mA, respectively. Switching behavior of the 4:1 multiplexer has also been checked up to 70 Gb/s.     

An 80-Gbit/s multiplexer IC using InAlAs/InGaAs/InP HEMTs

This paper describes the design and performance of an 80-Gbit/s 2:1 selector-type multiplexer IC fabricated with InAlAs/InGaAs/InP HEMTs. By using a double-layer interconnection process with a low-dielectric insulator, microstrip lines were designed to make impedance-matched, high-speed intercell connection of critical signal paths. The record operating data rate was measured on a 3-in wafer. In spite of the bandwidth limitation on the measurement setup, clear eye patterns were successfully observed for the first time. The obtained circuit speed improvement from the previous result of 64 Gbit/s owes much to this high-speed interconnection design     

Polarization independent InP WDM multiplexer/demultiplexer module

We report the design, fabrication, packaging, and characterization of a polarization independent integrated optical InP multiplexer/demultiplexer module. The device is based on a vertically etched diffractive grating and separates four channels with 4 spacing in the 1.55 μm window. An n^-/n⁺-InP layer structure with very low birefringence results in a shift of the passbands between transverse electric (TE) and transverse magnetic (TM) polarization of less than 0.1 nm. With a self-aligned flip-chip mounting technique light is optically coupled from the input and output waveguides to an array of lensed single mode fibers with a coupling efficiency of more than 80%. The packaging includes temperature control that allows fine tuning of the channel passbands over 5 nm. Optical crosstalk is always better than -17 dB and fiber to fiber losses of 15 dB are achieved. The module has been successfully implemented in a 4×2.5 Gb/s WDM transmission system     

A 4 Gbits/s GaAs 16:1 multiplexer/1:16 demultiplexer LSI chip

A GaAs 16:1 multiplexer (MUX)/1:16 demultiplexer (DMUX) LSI chip, which operates at data rates from 50 Mb/s up to 4 Gb/s in a multilayer ceramic package, is described. The LSI chip incorporates trees of 2:1 MUX and 1:2 DMUX. The 2:1 MUX is composed of a master-slave D-flip-flop (DFF) joined with a 2-1 selector. The 1:2 DMUX consists of DFFs which are either a master-slave or the tristage type. The package has 76 pins and consists of five layers, including four power layers, and is applicable up to 7.7 GHz operation. The LSI chip is fabricated using a flat-gate self-aligned implantation for n⁺-layer technology (FG-SAINT process)     

Si bipolar chip set for 10-Gb/s optical receiver

Three Si bipolar ICs, a preamplifier, a gain-controllable amplifier, and a decision circuit, have been developed for 10-Gb/s optical receivers. A dual-feedback configuration with a phase adjustment capacitor makes it possible to increase the preamplifier bandwidth up to 11.2 GHz, while still retaining flat frequency response. The gain-controllable amplifier, which utilizes a current-dividing amplifier stage, has an 11.4-GHz bandwidth with 20-dB gain variation. A master-slave D-type flip-flop is also operated as the decision circuit at 10 Gb/s. On-chip coplanar lines were applied to minimize the electrical reflection between the ICs     

0.18-μm CMOS 10-Gb/s multiplexer/demultiplexer ICs using currentmode logic with tolerance to threshold voltage fluctuation

A feedback MOS current mode logic (MCML) is proposed for the high-speed operation of CMOS transistors. This logic is more tolerant to the threshold voltage fluctuation than the conventional MCML and is suitable for gigahertz operation of deep-submicron CMOS transistors. Using this logic, 8:1 multiplexer (MUX) and 1:8 demultiplexer (DEMUX) ICs for optical-fiber-link systems have been fabricated with 0.18-μm CMOS transistors. The ICs are faster than conventional CMOS MUX and DEMUX ICs and their power consumption is less than 1/4 of that of the conventional 10-Gb/s MUX and DEMUX ICs made using Si bipolar or GaAs transistors     

Low-power 50 Gbit/s InP HBT 1:4 demultiplexer IC with multiphase clock architecture

An InP HBT 1:4 demultiplexer IC with a multiphase clock architecture is described that reduces the number of circuit elements and power consumption while maintaining operating speed. The IC operated at 50 Gbit/s with 1.17 W power consumption at a supply voltage of -4.5 V. Compared to an IC with a conventional tree-type architecture using the same InP HBTs, the power consumption is less than half while the operating speed of 50 Gbit/s is maintained.     

40-Gb/s 2:1 multiplexer and 1:2 demultiplexer in 120-nm standard CMOS

We present an integrated 2:1 multiplexer and a companion 1:2 demultiplexer in CMOS. Both integrated circuits (ICs) operate up to a bit rate of 40 Gb/s. The 2:1 multiplexer features two in-phase data inputs which are achieved by a master-slave flip-flop and a master-slave-master flip-flop. Current-mode logic is used because of the higher speed compared to static CMOS and the robustness against common-mode disturbances. The multiplexer uses no output buffer and directly drives the 50-/spl Omega/ environment. An inductance connected in series to the output in combination with shunt peaking is used to enhance the bandwidth of the multiplexer. Fully symmetric on-chip inductors are used for peaking. The inductors are mutually coupled to save chip area. Lumped equivalent models of both peaking inductors allow optimization of the circuit. The ICs are fabricated in a 120-nm standard CMOS technology and use 1.5-V supply voltage. Measured eye diagrams of both ICs demonstrate their performance.     

2.488 Gb/s SONET multiplexer/demultiplexer with frame detectioncapability

The authors describe a novel scheme that allows a demultiplexer, a byte aligner, and a frame detection circuit tube to be integrated on one chip without compromising the demultiplexer's performance. A research prototype integrated circuit (IC) that incorporates this scheme was designed to operate at speeds up to the SONET STS-48 (synchronous transport signal level 48) rate of 2.488 Gb/s. The IC is implemented in GaAs enhancement/depletion mode MESFET technology, and it performs 1:8 demultiplexing, byte alignment, and SONET frame detection functions. A separate IC that performs 8:1 multiplexing was also implemented using the same technology. The bit error rate; test results show that the multiplexer and demultiplexer with frame detector can operate at 2.488 Gb/s with a bit error rate less than 1×10^-14. Both ICs were tested at data rates up to 3 Gb/s     

12-Gb/s 0.25-μm CMOS 1:4分接器

介绍光纤传输系统的组成,分析1:4分接器的树型结构,并给出其主要特点.在此基础上,进一步探讨树型结构中所用的1:2分接器,并给出其中的锁存器电路结构.此外,讨论了起重要作用的匹配电路以及驱动电路.电路采用标准的0.25μm CMOS工艺设计并实现.实际测试结果显示该电路能够稳定地在STM-16至STM-64所要求的数据速率下工作,最高工作速率为12.92Gb/s.     

Tunable birefringent wavelength-division multiplexer/demultiplexer

A tunable wavelength-division multiplexer/demultiplexer, based on a polarisation-insensitive birefringent optical filter design, is described. The two channels of the device can each be tuned, with the channel separation adjustable over a wide range. Experiments with 6 to 30 nm laser channel separations have yielded optical crosstalk values of less than ?20 dB.     

A 43-Gb/s full-rate-clock 4:1 multiplexer in InP-based HEMT technology

This paper describes a full-rate-clock 4:1 multiplexer (MUX) in a 0.13-/spl mu/m InP-based HEMT technology for 40-Gb/s and above optical fiber link systems. To reduce output jitter, the serialized data are retimed at the final stage by a retimer, a D-type flip-flop, which has a symmetric layout with an optimized spacing to the ground that minimizes coupling capacitances. A phase adjuster, composed of an exclusive OR and a delay switch, uses external control signals to change each phase of the serialized data and clock entering the retimer and gives a correct timing for the clock to drive the retimer. A clock distributor with a simple wired splitter divides the clock into two clocks with high gain and low current. The MUX integrates 1355 HEMTs formed using electron beam lithography. A chip mounted in a test module operated at up to 47 Gb/s with a power consumption of 7.9 W for a single supply voltage of -5.2 V.     

Monolithic integrated 4:1 multiplexer and demultiplexer operating up to 4.8 Gbit/s

The letter describes the high-speed performance of a 4:1 time-division MSI multiplexer and demultiplexer, which are fabricated using advanced super self-aligned process technology (SST). The maximum operation speed of the multiplexer is 5.02 GHz under 576 mW power dissipation. The system, which is composed of a multiplexer and a demultiplexer, operates at up to 4.80 GHz. The demultiplexer has a power dissipation of 1148 mW. Interchannel interference is also examined.     

High-isolation single-mode wavelength-division multiplexer/demultiplexer

A single-mode fibre-optic wavelength-division multiplexer/demultiplexer with excellent isolation is reported. The device utilises a fused biconical structure similar to that of 3 dB couplers and exhibits an insertion loss of 0.04 dB and a wavelength isolation of 43 dB at 1.300 ?m and 30 dB at 1.523 ?m.     

A 20-Gb/s CMOS multichannel transmitter and receiver chip set forultra-high-resolution digital displays

A multichannel transmitter (TX) and receiver (RX) chip set operating at 20 Gb/s (5 Gb/s×4 ch) has been developed by using 0.25-μm CMOS technology. To achieve multichannel data transmission and high-speed operation, the chip set features: (1) circuits for compensating the phase difference between multiple RX chips, which is due to data skew resulting from different lengths of transmission cables, and for compensating the frequency difference between the system clocks of the TX and RX chips; (2) a self-alignment phase detector with parallel output for a high-speed data-recovery circuit; and (3) a fully pipelined 8B10B encoder. At a 2.5-V power supply, the power consumption of the TX chip during 5-Gb/s operation is 500 mW and that of the RX chip is 750 mW. Four of these TX/RX chip sets can provide an aggregate bandwidth of 20 Gb/s     

132.2-Gb/s PDM-8QAM-OFDM Transmission at 4-b/s/Hz Spectral Efficiency

In this letter, we investigate 132.2-Gb/s polarization- division-multiplexed orthogonal frequency-division-multiplexing (PDM-OFDM) transmission at 25-GHz channel spacing. We show that the nonlinear tolerance is dependent on the OFDM symbol length. By using 14.4-ns-long OFDM symbols, 7 $, times ,$132.2-Gb/s transmission of PDM-OFDM at 4-b/s/Hz spectral efficiency is reported over 1300-km standard single-mode fiber.      

A 165-Gb/s 4:1 Multiplexer in InP DHBT Technology

This paper presents a 4:1 multiplexer fabricated in InP double heterojunction bipolar transistor (DHBT) technology. The multiplexer works up to 165 Gb/s at a supply voltage of$-hbox3.2~V$consuming 1.6 W. It is a half-rate multiplexer using a multi-phase clock architecture. The main design challenge was to ensure correct timing between clock and data signals.