High-Temperature Failure Mechanisms of Hot-Pressed Si3N4 and Si3N4/Si3N4-Whisker-Reinforced Composites

The high-temperature flexural strength of hot-pressed silicon nitride (Si₃N₄) and Si₃N₄-whisker-reinforced Si₃N₄-matrix composites has been measured at a crosshead speed of 1.27 mm/min and temperatures up to 1400°C in a nitrogen atmosphere. Load–displacement curves for whisker-reinforced composites showed nonelastic fracture behavior at 1400°C. In contrast, such behavior was not observed for monolithic Si₃N₄. Microstructures of both materials have been examined by scanning and transmission electron microscopy. The results indicate that grain-boundary sliding could be responsible for strength degradation in both monolithic Si₃N₄ and its whisker composites. The origin of the nonelastic failure behavior of Si₃N₄-whisker composite at 1400°C was not positively identified but several possibilities are discussed.     

Solubility of Si3N4 in Liquid SiO2

The nitrogen solubility in the SiO₂-rich liquid in the metastable binary SiO₂-Si₃N₄ system has been determined by analytical TEM to be 1%–4% of N/(O + N) at 1973–2223 K. Analysis of the near edge structure of the electron energy loss peak indicates that nitrogen is incorporated into the silicate network rather than being present as molecular N₂. A regular solution model with a positive enthalpy of mixing for the liquid was used to match the data for the metastable solubility of N in the presence of crystalline Si₃N₄ and to adjust the computed phase diagram. The solubility of Si₃N₄ in fused SiO₂ is far less than reported in liquid silicates also containing Al, Mg, and/or Y. Apparently, these cations act as modifiers that break anion bridges in the silicate network and, thereby, allow further incorporation of Si₃N₄ without prohibitive amounts of network cross-linking. Finally, indications emerged regarding the diffuse nature of the Si₃N₄-SiO₂ interface that leads to amorphous regions of higher N content.     

Sintering of Si3N4-Y2O3-Al2O3

Sintering kinetics of the system Si₃N4-Y2O₃-Al₂O3 were determined from measurements of the linear shrinkage of pressed disks sintered isothermally at 1500° to 1700°C. Amorphous and crystalline Si₃N₄ were studied with additions of 4 to 17 wt% Y₂O₃ and 4 wt% A1₂O₃. Sintering occurs by a liquid-phase mechanism in which the kinetics exhibit the three stages predicted by Kingery's model. However, the rates during the second stage of the process are higher for all compositions than predicted by the model. X-ray data show the presence of several transient phases which, with sufficient heating, disappear leaving mixtures of β ' -Si₃N₄ and glass or β '-Si₃N₄, α '-Si₃N₄, and glass. The compositions and amounts of the residual glassy phases are estimated.     

Oxidation and Strength Retention of Monolithic Si3N4 and Nanocomposite Si3N4-SiC with Yb2O3 as a Sintering Aid

The oxidation behaviors of monolithic Si₃N₄ and nanocomposite Si₃N₄-SiC with Yb₂O₃ as a sintering aid were investigated. The specimens were exposed to air at temperatures between 1200° and 1500°C for up to 200 h. Parabolic weight gains with respect to exposure time were observed for both specimens. The oxidation products formed on the surface also were similar, i.e., a mixture of crystalline Yb₂Si₂O₇ and SiO₂ (cristobalite). However, strength retention after oxidation was much higher for the nanocomposite Si₃N₄-SiC compared to the monolithic Si₃N₄. The SiC particles of the nanocomposite at the grain boundary were effective in suppressing the migration of Yb³⁺ ions from the bulk grain-boundary region to the surface during the oxidation process. As a result, depletion of yttribium ions, which led to the formation of a damaged zone beneath the oxide layer, was prevented.     

Hot Isostatic Pressing of Si3N4 Powder Compacts and Reaction-Bonded Si3N4

Hot isostatically pressed silicon nitride was produced by densifying Si₃N₄ powder compacts and reaction-bonded Si₃N₄ (RBSN) parts with yttria as a sintering additive. The microstructure was analyzed using scanning electron microscopy, X-ray diffraction, and density measurements. The influence of the microstructure on fracture strength, creep, and oxidation behavior was investigated. It is assumed that the higher amount of oxygen in the Si₃N₄ starting powder compared with the RBSN starting material leads to an increased amount of liquid phase during densification. This results in grain growth and in a larger amount of grain boundary phase in the hot isostatically pressed material. Compared with the hot isostatically pressed RBSN samples therefore, strength decreases whereas the creep rate and the weight gain during oxidation increase.     

Phase Evolution in Heat-Treated Si3N4 with Additions of Yb2O3

The heat treatment of silicon nitride (Si₃N₄) ceramics with additions of 8, 12, and 16 wt% Yb₂O₃ was carried out at different temperatures and the evolution of grain boundary (GB) phase was investigated systematically by X-ray diffraction (XRD) as well as scanning electron and transmission electron microscopic analyses. XRD results reveal that the extent and the ease of GB crystallization increase with increasing the Yb₂O₃ content, and that high heat-treatment temperatures in general favor crystallization of the quaternary compounds such as the Yb₄Si₂O₇N₂ phase. These results provide an insight into the GB phase evolution in the Yb-system Si₃N₄ ceramics subjected to a postsintering heat treatment.     

Phase Relations in the Si3N4-Rich Portion of the Si3N4–AlN–Al2O3–Y2O3

The phase relations in the Si₃N₄-rich portion of the Si₃N₄–AlN–Y₂O₃ rystem were investigated using hot-pressed bodies. The one-phase fields of β3 and α, the twophase fields of β+α, β+M (M=melilite), and α+M, and the three-phase fields of β+α+M were observed in the Si₃N₄-rich portion. The α- and β-sialons are not two different compounds but an allotropic transformation phase of the Si–Al–O–N system, and an α solid solution expands and stabilizes with increasing Y₂O₃ content. Therefore, the formulas of the two sialons should be the same.     

Pressureless Sintering of Dense Si3N4 and Si3N4/SiC Composites with Nitrate Additives

The effect of aluminum and yttrium nitrate additives on the densification of monolithic Si₃N₄ and a Si₃N₄/SiC composite by pressureless sintering was compared with that of oxide additives. The surfaces of Si₃N₄ particles milled with aluminum and yttrium nitrates, which were added as methanol solutions, were coated with a different layer containing Al and Y from that of Si₃N₄ particles milled with oxide additives. Monolithic Si₃N₄ could be sintered to 94% of theoretical density (TD) at 1500°C with nitrate additives. The sintering temperature was about 100°C lower than the case with oxide additives. After pressureless sintering at 1750°C for 2 h in N₂, the bulk density of a Si₃N₄/20 wt% SiC composite reached 95% TD with nitrate additives.     

The System Si3N4-SiO2-Y2O3

Subsolidus phase relations were established in the system Si₃N₄-SiO₂-Y₂O₃. Four ternary compounds were confirmed, with compositions of Y₄Si₂O₇N₂, Y₂Si₃O₃N₄, YSiO₂N, and Y₁₀(SiO₄)₆N₂. The eutectic in the triangle Si₃N₄-Y₂Si₂O₇-Y₁₀(SiO₄)₆N₂ melts at 1500°C and that in the triangle Si₂N₂O-SiO₂-Y₂Si₂O₇ at 1550°C. The eutectic temperature of the Si₃N₄-Y₂Si₂O₇ join was ∼ 1520°C.     

Sintering of Si3N4-Y2O3 Under Nitrogen Pressure

This study shows that the amount ofAl₂O₃ needed to form high density Si₃N₄-15Y₂-O₃ samples can be reduced by using high surface area Si₃N₄ powder and high N₂ overpressure (high sintering temperatures) during the sintering process. The reduction in AI₂O₃ content results in improved oxidation resistance of the sintered samples.     

Hot-Pressing of Si3N4 with Y2O3 and Li2O as Additives

The rates of densification and phase transformation undergone by α-Si₃N₄ during hot-pressing in the presence of Y₂O₃, Y₂O₃−2SiO₂, and Li₂0−2Si0₂ as additives were studied. Although these systems behave less simply than MgO-doped Si₃N₄, the data can be interpreted during the early stages of hot-pressing as resulting from a solution-diffusion-reprecipitation mechanism, where the diffusion step is rate controlling and where the reprecipitation step invariably results in the formation of the β-Si₃N₄ phase.     

Comparison of Tribological Behavior Between α-Sialon/Si3N4 and Si3N4/Si3N4 Sliding Pairs in Water Lubrication

We report here the study on tribological behavior of α-Sialon in aqueous medium. The results derived from a wide range of test conditions are briefly discussed. A reduction in friction coefficient from 0.7 to 0.03 and a decrease in wear rate by two orders of magnitude were achieved under low load (9.8 N) and high speed (>0.54 m/s) conditions. The tribological behavior of α-Sialon/Si₃N₄ ceramics was then compared with Si₃N₄/Si₃N₄ tribopairs.     

Reaction-Bonding Preparation of Si3N4/MoSi2 and Si3N4/WSi2 Composites from Elemental Powders

Si₃N₄/MoSi₂ and Si₃N₄/WSi₂ composites were prepared by reaction-bonding processes using as starting materials powder mixtures of Si-Mo and Si-W, respectively. A presintering step in an At-base atmosphere was used before nitriding for the formation of MoSi₂ and WSi₂; the nitridation in a N₂-base atmosphere was followed after presintering with the total stepwise cycle of 1350°C × 20 h +1400°C × 20 h +1450°C × 2 h. The final phases obtained in the two different composites were Si₃N₄ and MoSi₂ or WSi₂; no free elemental Si and Mo or W were detected by X-ray diffraction.     

Compressive Creep and Oxidation Resistance of an Si3N4 Material Fabricated in the System Si3N4-Si2N2O-Y2Si2O7

The compressive creep behavior and oxidation resistance of an Si₃N₄/Y₂Si₂O₇ material (0.85Si₃N₄+0.10SiO₂+0.05Y₂O₃) were determined at 1400°C. Creep re sistance was superior to that of other Si₃N₄ materials and was significantly in creased by a preoxidation treatment (1600°C /120 h). An apparent parabolic rate constant of 4.2 × 10⁻¹¹ kg²·m-⁴·s⁻¹ indicates excellent oxidation resistance.     

Densification of Si3N4 with LiYO2 Additive

This paper deals with the densification and phase transformation during pressureless sintering of Si₃N₄ with LiYO₂ as the sintering additive. The dilatometric shrinkage data show that the first Li₂O- rich liquid forms as low as 1250°C, resulting in a significant reduction of sintering temperature. On sintering at 1500°C the bulk density increases to more than 90% of the theoretical density with only minor phase transformation from α-Si₃N₄ to β-Si₃N₄ taking place. At 1600°C the secondary phase has been completely converted into a glassy phase and total conversion of α-Si₃N₄ to β-Si₃N₄ takes place. The grain growth is anisotropic, leading to a microstructure which has potential for enhanced fracture toughness. Li₂O evaporates during sintering. Thus, the liquid phase is transient and the final material might have promising mechanical properties as well as promising high-temperature properties despite the low sintering temperature. The results show that the Li₂O−Y₂O₃ system can provide very effective low-temperature sintering additives for silicon nitride.