基于Android平台的物流仓储叉车调度系统的设计

传统仓储作业中,叉车完全由人工调派,管理人员无法获得叉车位置信息,调度效率低。为此,本文设计了一款基于Android平台的物流仓储叉车调度系统,由Android手机移动终端、服务器调度端、无线路由器三部分组成。该系统采用了基于Wi-Fi信号指纹的室内定位方法实现对叉车的实时定位。测试结果表明,该系统可以对实时显示叉车终端位置,并实现双向语音对讲,极大提高了调度效率。     

移动宽带终端的现状和发展趋势

移动终端向移动宽带终端的转变是移动网络向3G发展的产物,移动宽带终端在3G中占据着重要的位置。文章对移动宽带终端的发展现状作了概述,并对它的发展趋势作了较为深入的探讨。     

传感器辅助的WiFi指纹室内定位方法

针对Wi Fi指纹室内定位技术中信号传播时变性大导致定位精度低的问题,提出一种传感器辅助的Wi Fi指纹定位方法。首先根据移动终端内置的加速度传感器判断用户的走步状态,以减少信号时变所引起的定位误差;然后利用终端中的磁力计与陀螺仪,通过传感器融合来计算用户的运动方向。最后结合所得的方向信息和历史位置计算终端位置,以减少指纹图中与终端反向的指纹带来的干扰,从而减少指纹匹配计算的复杂度。实验结果表明,提出的传感器辅助Wi Fi指纹定位技术能减小位置估计误差并提高定位的鲁棒性。     

3G移动终端流媒体播放技术的研究

3G网络通信数据增值业务的迅速发展,使得无线流媒体应用越来越受到人们的关注。因此在移动网络环境中,针对手机终端的流媒体解码播放技术正成为研究热点。在对3G网络中移动终端的视频解码技术进行探讨基础上,设计了从PC端向移动终端发送音、视频内容的无线流媒体的具体应用系统,实现了在Symbian平台手机终端的H.264协议的解码播放,解码效果良好基本满足实时解码的要求。     

基于LBS的车辆定位管理系统的设计和实现

位置服务作为移动通信网提供的一种增值业务正悄然兴起,随着电信PHS及3G的发展,基于位置的综合信息服务有了更为广阔的发展空间。本文从SP利用LBS业务发展车辆定位跟踪和管理调度的市场的角度,讨论了一个LBS车辆定位管理系统设计中所涉及的LBS技术、移动终端嵌入式系统、网络通信协议、GIS系统等关键技术问题。     

A-GPS终端一致性测试

A-GPS(Assisted Global Positioning System)是一种通过移动通信网络辅助的全球定位技术,此技术结合了两类位置信息,一类是移动台通过自身GPS接收机获得的,而另一类则是移动台通过移动通信网络获取的。A-GPS技术可以在2G,3G以及未来4G的通信网络中部署应用,移动终端应用A-GPS定位业务,需要增加A-GPS接收机及相应信号处理模块。A-GPS的终端一致性认证,即对于移动终端的A-GPS功能部分进行一致性验证,目前国际上采用的包含A-GPS一致性测试规范有3GPP51.010,3GPP34.171,3GPP34.123,3GPP2C.S0036,3GPP2C.S0059,OMA-ETS-SUPL等,本文对上述规范做了详细介绍。     

基于LBS的车辆定位管理系统的设计和实现

位置服务作为移动通信网提供的一种增值业务正悄然兴起，随着电信PHS及3G的发展，基于位置的综合信息服务有了更为广阔的发展空间。本从SP利用LBS业务发展车辆定位跟踪和管理调度的市场的角度，讨论了一个LBS车辆定位管理系统设计中所涉及的LBS技术、移动终端嵌入式系统、网络通信协议、GIS系统等关键技术问题。     

基于室内外定位的校园LBS系统设计与实现

为了解决目前智能手机中位置服务LBS(Location Based Service)类移动应用在小环境区域不能准确提供位置服务的问题,以校园为例提出了一种基于室内外定位的LBS系统设计方案。首先介绍系统结构设计,然后详细分析了Mobile GIS、GPS、基于Wi Fi信号强度值的位置指纹定位算法等系统设计中的关键技术,最后测试验证系统的各个功能模块。测试结果表明,系统可以实现终端定位、室内位置服务、校园导航、地图服务等功能,且操作便捷,具备可行性和实用性。     

移动通信终端定位技术自主可控发展研究

移动通信终端的位置信息是通信用户的重要隐私信息。尤其在国防通信系统中,位置信息更是涉及到安全性和保密性问题,因此,移动终端定位技术的自主可控性显得更为重要。本文介绍了目前常用的移动终端定位技术,分析了各种技术自主可控性,结合我国现状,对移动终端定位技术的自主可控性提出了发展建议。     

基于无线传感网络的智能移动监控系统设计

为解决部分环境监控需要管理人员值守问题,提出了一种基于ZIGBEE与3G网络的环境智能移动监控系统。系统采用CC2530主控芯片,将传感器所采集到的数据通过ZIGBEE无线网络协议传输到PC终端。在3G网络环境中, VC编制的上位机与安卓智能移动设备根据TCP/IP通信协议进行数据通讯。实验结果表明：管理人员通过使用上位机或者安卓智能移动终端都能实时、准确、有效地监控被测环境因子数据。     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.