磨粒对ADZ复合陶瓷材料磨损性能的影响

采用块 -块摩擦磨损试验机在不同磨粒的 5 %NaOH泥浆中 ,对氧化铝增强四方氧化锆多晶陶瓷材料 (ADZ)的磨损性能进行了研究。研究结果表明尖锐磨粒对ADZ复合陶瓷材料磨损的影响要比球形磨粒严重的多 ,磨料硬度是影响陶瓷材料磨损率的重要因素 ,磨损率随磨粒硬度的提高而增大。在不同形状的SiO2 磨粒的泥浆中ADZ陶瓷材料的主要磨损机理为塑性变形和微犁削。在高硬度Al2 O3磨料的泥浆中ADZ陶瓷材料磨损表面以断裂机制占主导地位。     

微裂纹特性对复合材料切削性能影响研究

通过观察碳化硅颗粒增强铝基复合材料（SiCp/Al）切削加工试验过程,测量并分析了不同切削用量条件下切削力、切屑形态及微观金相组织的变化规律,采用对比分析方法得出了切屑形态的变化与切削用量及切削力之间的关系,SiCp/Al复合材料的内部缺陷,例如颗粒分布不均匀、微裂纹以及气孔是影响其切削性能的主要因素。     

轴向超声振动辅助磨削的磨削力建模

以单颗磨粒为对象,分析轴向超声振动下磨粒的运动特性。在此基础上,将磨削力分为切屑变形力和摩擦力两部分,分别分析了轴向超声振动对切屑变形力和摩擦力的影响。在切屑变形力方面,轴向超声振动改变了磨粒运动方向与主切削方向间的夹角;在摩擦力方面,轴向超声振动降低了磨粒与工件间的摩擦因数。基于此建立了轴向超声振动辅助磨削的磨削力模型。通过对21Ni Cr Mo5H进行了轴向超声振动辅助磨削的磨削力试验,确定了模型中的常数,并验证了所建模型的正确性。建立的磨削力模型是轴向超声振动辅助磨削的磨削力预测的一种有效方法,对轴向超声振动辅助磨削机理的认识具有较大意义。     

硅晶片化学机械抛光材料去除机制与模型

通过分析软质层的形成、作用以及纳米磨料的自身变形对材料去除的影响，改进了CMP过程的接触力学模型；分析了纳米磨料自身变形量对磨料嵌入硅晶片基体材料的深度的影响，以及纳米磨料硬度对抛光表面粗糙度的影响。结果表明：软质层的存在增加了单个纳米磨料所去除材料的体积，且对基体材料有保护作用，减小了纳米磨料嵌入基体材料的深度；纳米磨料的自身变形抵消了纳米磨料嵌入基体材料的切削深度，从而也决定了抛光表面的粗糙度；纳米磨料的自身变形量与纳米磨料的硬度有关，硬度低的纳米磨料自身变形量大，因而切削深度小，抛光后表面的粗糙度值低。     

6061-T651铝合金单颗磨粒磨削仿真

通过简化并建立单颗磨粒磨削模型,采用ANSYS LS-DYNA进行对6061-T651特种铝合金磨削过程的理论研究和仿真分析,总结了单颗磨粒的磨削速度、磨削深度等工艺参数对磨削力大小以及磨屑的影响。研究表明:随着磨削速度的增加,单个磨料颗粒的磨削力减小,并且递减速率呈先增大后减小的趋势;而磨削深度的增加则会使单个磨料颗粒的磨削力增大,且递增速率逐渐减缓。磨削过程中,磨屑形状受加工参数的影响,其中,磨削深度对磨屑形状的影响比磨削速度对磨屑形状的影响更大。     

基于滑—停—滑机理的锯齿形切屑高速成形分析

高速车削时被切削材料以极高的应变速率产生连续的塑性变形,产生大量的切削热,在出现集中剪切滑移的情况下,产生了连续型带状锯齿形切屑。根据高速外圆车削中碳淬硬钢切屑试样的SEM照片和金相显微组织照片分析了锯齿形切屑周期性形成的变形机理。被切削材料的变形过程由普通的剪切滑移变形和集中剪切滑移变形组成,切屑沿前刀面的流出可细分为“滑—停—(再)滑”三个阶段。切削速度和材料硬度是决定切屑变形的两个主要影响因素。只要能够使材料应变率增加、致使切削温度升高的因素改变达到某种临界状态都能促成锯齿形切屑的形成,锯齿形切屑的形态随着切削用量的改变而变化。     

Particle movement patterns and their prediction in abrasive flow machining

Abrasive particle movement pattern is an important factor in estimating the wear rate of materials, especially, as it is closely related to the burring, buffing and polishing efficiency of the abrasive flow machining (AFM) process. There are generally two kinds of particle movement patterns in the AFM process, i.e. sliding–rubbing and rolling. In mechanism, AFM grain–workpiece interaction is taking place in any one or a combination of the possible modes: elastic/plastic deformation by sliding–rubbing grain movement; elastic/plastic deformation by rolling grain movement; chip formation (micro‐cutting) by rubbing grain movement; ridges formation by rubbing and rolling grain movement; and low‐cycle fatigue wear. Therefore, the machining efficiency of a machine part is predominantly dependent upon the particle movement patterns. In this paper, normal load, particle size and hardness of machine parts were investigated to understand the involved parameters of particle movement patterns and propose a computer statistic prediction of particle movement patterns. It has been found that there are two cases. In case of large‐size particles, the ratio of rolling particles is increased with increasing normal load. For small‐size particles, the ratio of grooving particles is increased with increasing normal load and vice versa. When normal load is light, the particle size cannot usually give an effect on movement patterns. That influence will be predominant under heavy normal load. Most of the particles will tend to groove when the particle size is below a certain value. Hardness of the material and their hardness difference for tribological pairs are other important monitors in predicting particle movement patterns. In this research, increasing hardness of materials results in more rolling particles, which results in much less cutting particles. Copyright © 2007 John Wiley & Sons, Ltd.     

基于SPH法的CBN磨粒切削过程数值模拟

采用光滑粒子流体动力学法进行CBN磨粒切削过程仿真。该方法解决了网格法模拟材料分离时的网格束缚问题。通过切削过程中磨粒与工件材料的应力场变化以及离散SPH粒子的运动情况,分析了CBN磨粒的磨损机理以及工件材料的切削变形机理。研究结果表明:磨粒的顶部与挤压面棱边接触应力集中,易发生磨耗与微破碎磨损;工件材料受磨粒的推挤发生弹塑性变形而沿磨粒的侧向及前方隆起,并于磨粒的前方挤出而形成切屑。

     

SiCP/Al复合材料延性去除加工的有限元分析

以断裂力学的有关理论为依据,运用ABAQUS有限元分析软件研究在固定的磨削速度下,单个磨粒磨削单颗粒SiCp/Al复合材料的延性去除问题.结果表明:SiC颗粒所受到的拉伸应力和压缩应力都随磨削深度的增加而增大;SiC颗粒发生延性去除的极限切深为0.6μm,SiC颗粒发生延性去除时其最大压缩应力大于26GPa,同时最大拉...     

基于Abaqus的砂带磨削单磨粒建模与仿真

对砂带磨削中单颗磨粒磨削过程进行了分析与建模,并利用Abaqus软件对具有不同负前角、切削速度与切削深度的单磨粒磨削过程中磨削力和温度的变化进行了仿真。分析结果表明,随着磨粒前角以及磨削深度的增大,磨削力和磨削温度都会增大。当磨削厚度达到一定程度时,将会出现锯齿型切屑,而切削速度对切向力影响较小。     

Morphology evolution and micro-mechanism of chip formation during high-speed machining

In this paper, the morphology and micro-mechanism of chip formation during high-speed machining aluminum alloy 7050-T7451 is investigated based on the combination of dislocation theory and plastic deformation theory. Experiments of quick stop stoppage for turning and special method (Buda) for milling process were carried out in order to obtain shear angle in different cutting speeds. The results show that effective flow stress and temperature in front edge zone is higher and more concentrated than that in other deformation zones. The shear front-lamellar structure was observed and analyzed in the front edge zone which influences the chip formation directly. The influence of cutting speed on chip formation was analyzed by simulation and experiments. Cutting speed is an important factor affecting the morphology evolution and chip formation. When the cutting speed is below 1500 m/min, the concentration of shear stress and the shear front-lamella structure of cutting deformation are more remarkable and easier for forming continuous ribbon chips. With the cutting speed increase, the ribbon chip transforms into serrated chip when a critical cutting speed (2500 m/min) is reached. Finally, microscopic mechanism of chip formation has been revealed and critical condition of the shear front—the layer structure formation—has been determined.     

碳纤维复合材料/钛合金叠层钻孔质量研究

碳纤维复合材料(Carbon fiber reinforced plastic,CFRP)/钛合金叠层的钻孔机理不同于单层材料钻孔,钛合金切屑在排出孔外过程中会对CFRP孔质量造成损伤。为了探究CFRP在叠层钻孔时的质量特性,设计正交试验分析了钛合金切屑和切削参数对CFRP层钻孔质量的影响。观察了轴向切削力和力矩的变化以及钛合金切屑形态,分析CFRP层孔径超差和入口撕裂的机理。结果表明:大进给量条件下,高温、高硬度的钛合金切屑会对CFRP产生严重的侵蚀,是导致CFRP孔径超差的主要原因,并会增大入口撕裂程度;CFRP入口撕裂主要产生在切削速度和纤维方向夹角θ=45°的位置,低切削速度不利于切削CFRP,会加大入口撕裂程度。因此,应使用小进给量钻削钛合金层,使用大切削速度钻削CFRP层;在保证钻头强度的前提下,推荐使用具有较大容屑空间的钻头。     

Experimental investigation on cutting mechanisms in fixed diamond wire sawing of bone

Bone sawing has been widely used in performing bone surgery. However, thermal necrosis, loss of cutting precision and surface damage may occur in cutting process. The primary objective of this research is to improve cutting performance of bone by advantages of diamond wire sawing. Mechanism of material removal, cutting force, temperature and surface quality are analyzed based on experimental results. It is indicated that wire sawing provides small depth of cut, which is effective to obtain ductile material removal mode. Due to small material removal rate per abrasive, thermal energy is low and most of the heat can be taken away by the cyclic wire and bone chips. Consequently, cutting force and temperature in cutting zone are lower than that of traditional sawing. Due to the high efficiency of chip ejection, burrs and fracture are reduced and a significant improvement in surface quality is achieved. Based on cutting experiments with various values of cutting parameters, it is observed that better performance is achievable at higher wire speeds. These results provide a valuable basis for application of wire sawing and understanding of bone cutting mechanisms.     

混凝土锯切加工过程的基本特征

通过金刚石单颗粒划伤、金刚石单个节块锯切和金刚石锯片锯切系列试验，对混凝土锯切加工过程中的切屑形态和切削区表面形貌，以及切削力等基本特征进行了详细讨论。结果表明：金刚石锯片锯切混凝土的过程表现为高速锯切过程中金刚石锯片的冲击引起混凝土表层断裂破碎，水泥石子等在切削区内层受到金刚石磨粒的微切削作用形成粉屑，以及钢纤维和钢丝发生金属塑性变形断裂或被拔拉而断裂的过程。在粘性水泥粉屑以及金刚石磨粒的挤压作用下，多种形态的切屑易粘结成团，并粘附到混凝土锯切表面和锯片节块上而导致锯片堵塞。     

La2O3对铜基自润滑复合材料高温摩擦磨损性能的影响

为进一步提高铜基自润滑复合材料的硬度和高温摩擦磨损性能,采用粉末冶金热压法向铜-石墨烯-WS2复合材料中引入La2O3增强相颗粒,并对铜-石墨烯-WS2复合材料和La2O3增强铜-石墨烯-WS2复合材料在不同温度下的摩擦磨损性能进行对比研究。结果表明:复合材料烧结过程中各组元没有发生分解或互相反应,烧结后材料结构致密并且各组元均匀分布于基体中,La2O3增强相的引入在提高复合材料硬度的同时会降低材料热导率;室温下2种复合材料摩擦因数和磨损率比较相近,而高温下石墨烯和WS2的氧化导致Cu-RGO-WS2复合材料摩擦磨损性能下降,而La2O3则能发挥增强相作用和高温自润滑作用,使Cu-RGO-WS2-La2O3复合材料的高温摩擦磨损性能更优异。室温下铜-石墨烯-WS2复合材料的磨痕处仅发生了轻微的塑性变形,而La2O3增强铜-石墨烯-WS2复合材料的磨损机制主要是磨粒磨损;高温下铜-石墨烯-WS2复合材料的磨损机制为黏着磨损,而La2O3增强铜-石墨烯-WS2复合材料的磨损机制则为磨粒磨损和疲劳磨损。     

Characterization of chip formation during machining 1045 steel

A deep understanding of the generation and characterization of chip formation can result for practical advices of chip type controlling in engineering applications. The chip formation is divided into the continuous chip and the serrated one in this study. The characterization of the continuous chip formation is expressed as the chip deformation and that of the serrated chip formation is expressed as the frequency of serration, the degree of segmentation, and the deformation of serrated chip. The chips of 1045 steel under different cutting speeds (100–3,600?m/min) are collected during machining. After inlay and polishing of the collected chips, the chip morphology is observed with VHX-600 ESO digital microscope. It is found that at the cutting speeds of 100–400?m/min, the chip type is continuous, at the cutting speeds of 600–2,200?m/min the chip type is serrated, and at the cutting speeds of 2,500–3,600?m/min the chip type is segmented. The quantitative relations between the characterization parameters of chip formation and the cutting speed are obtained. The chip deformation increases with the cutting speed, and the influence of the cutting speed on the shear strain rate is more sensitive than that on the shear strain during the continuous chip formation. All the characterization parameters including the shear strain rate, the frequency of serration, the degree of segmentation, and the shear strain increase with the cutting speed during the serrated chip formation. The sensitivity of influence of the cutting speed on these parameters is in the following: the shear strain rate, the degree of segmentation, the frequency of serration, and the shear strain.     

低温液氮冷却下高速切削淬硬钢的切屑形成及刀具磨损

针对低温液氮冷却下淬硬钢高速车削过程中切屑形成及刀具磨损机理尚缺乏相关研究的问题,开展了液氮冷却下的淬硬钢高速切削研究,并与干切进行了对比.分析了切削力、切削温度、切屑特征以及刀具磨损特征,讨论了冷却润滑、切屑形成及刀具磨损机理.结果表明:与干切相比,各组实验中低温液氮冷却切削的切削温度降低了6.9％～9.9％,因材料...     

Chip Formation Mechanism of Inconel 718:A Review of Models and Approaches

Inconel 718,a nickel,chrome and iron alloy,has special advantages,such as high-temperature strength,thermal resistance and corrosion resistance,which facilitate wide usage in the aerospace industry,especially in the hot sec-tions of gas turbine engines.However,machining this alloy is correlated closely with the material's inherent properties such as excellent combination of strength,hardness and toughness,low thermal conductivity and the tendency to adhere to cutting tools.This nickel alloy also contains inclusions of hard abrasive carbide particles that lead to work-hardening of the workpiece material and thus abrasive wear of the cutting tool.That is,the machining of Inconel 718 is always influenced by high mechanical and thermal loads.This article reviews the chip formation mechanism of Inconel 718.One of the main characteristics in machining of Inconel 718 is that it will produce serrated or segmented chips in a wide range of cutting speeds and feeds.Existing studies show that the chip serration or segmentation by shear localization affects the machined surface integrity,and also contributes to the chip's evacuation and the auto-mation of machining operations.Thus,research conclusion indicates that the serrated or segmented chip phenom-enon is desirable in reducing the level of cutting force,and detailed analysis of models and approaches to understand the chip formation mechanism of Inconel 718 is vital for machining this alloy effectively and efficiently.Therefore,this article presents some summaries on the models and approaches on the chip formation in machining of Inconel 718.     

A micromechanics analysis of the material removal mechanisms in the cutting of ceramic particle reinforced metal matrix composites

In previous investigations on the cutting of ceramic particle reinforced metal matrix composites using the finite element (FE) method, the particles are usually considered to be rigid. This is inconsistent with the actual situation and thus makes the FE predictions less practical. This paper proposes a micromechanics model to investigate the material removal mechanisms by considering the elasticity and fracture of the particles. It was found that the interaction position of a particle relative to the cutting edge greatly influences the particle and matrix fracture, particle-matrix debonding, surface integrity and cutting forces. There are two particle cracking mechanisms. One is caused by the direct contact of the cutting edge with the particle, and the other is due to the indirect tool-particle interaction through matrix. When the cutting path is below a particle, a smooth surface without subsurface damage can be achieved. When it is passing through a particle, particle fracture mostly occurs. If it is above a particle, subsurface damage is dominated by particle-matrix debonding. Cutting force peaks once the cutting edge is in contact with a particle and the cutting edge is easier to be damaged when the tool is passing through the upper part of the particle.     

Abrasive wear behaviour of B4C particle reinforced Al2024 MMCs

In this study, the effects of volume fraction and particle size of boron carbide on the abrasive wear properties of B₄C particle reinforced aluminium alloy composites have been studied. For this purpose, a block-on-disc abrasion test apparatus was utilized where the samples slid against the abrasive suspension mixture at room conditions. The volume loss, specific wear rate and roughness of the samples have been evaluated. The effects of sliding time, particle content and particle size of B₄C particles on the abrasive wear properties of the composites have been investigated. The dominant wear mechanisms were identified using scanning electron microscopy. The results showed that the specific wear rate of composites decreased with increasing particle volume fraction. Furthermore, the specific wear rate decreased with increasing the size of particle for the composites containing the same amount of B₄C. Hence, it is deduced that aluminium alloy composites reinforced with larger B₄C particles are more effective against the abrasive suspension mixture than those reinforced with smaller B₄C particles.