A photochemical method for the preparation of indium oxide and indium-cobalt oxides thin films

Indium oxide and indium-cobalt oxide thin films have been successfully prepared by direct UV irradiation of amorphous films of β-diketonate complexes on Si(1 0 0) substrates. Deposited films were characterized by X-ray diffraction, Auger electron spectroscopy and X-ray photoelectron spectroscopy. The surface morphology of the films, examined by atomic force microscopy and scanning electron microscopy, revealed that mixed indium-cobalt oxide films are much smoother than In₂O₃ films, with rms surface roughness of 7.24 and 26.1 nm, respectively.     

Hydrothermal synthesis of β-nickel hydroxide nanocrystalline thin film and growth of oriented carbon nanofibers

Novel well-crystallized β-nickel hydroxide nanocrystalline thin films were successfully synthesized at low temperature on the quartz substrates by hydrothermal method, and the oriented carbon nanofibers (CNFs) were prepared by acetylene cracking at 750 °C on thin film as the catalyst precursor. High resolution transmission electron microscopy (HR-TEM) measurement shows that thin films were constructed mainly with hexagonal β-nickel hydroxide nanosheets. The average diameter of the nanosheets was about 80 nm and thickness about 15 nm. Hydrothermal temperature played an important role in the film growth process, influencing the morphologies and catalytic activity of the Ni catalysts. Ni thin films with high catalytic activity were obtained by reduction of these Ni(OH)₂ nanocrystalline thin films synthesized at 170 °C for 2 h in hydrothermal condition. The highest carbon yield was 1182%, and was significantly higher than the value of the catalyst precursor which was previously reported as the carbon yield (398%) for Ni catalysts. The morphology and growth mechanism of oriented CNFs were also studied finally.     

Effect of catalyst for nickel films for NiSi formation with improved interface roughness

Iodine is an effective catalyst to obtain homogeneous and smooth metal films with good interface properties. We adopted an iodine catalyst during the nickel film deposition by using atomic layer deposition (ALD) with bis(1-dimethylamino-2-methyl-2-butoxide)nickel [Ni(dmamb)₂] precursor and hydrogen reactant gas. The effect of iodine catalyst to nickel nucleation process was studied. The deposited films were silicided by rapid thermal process (RTP) which was performed by varying temperature from 400 °C to 900 °C in nitrogen ambient. The crystalline properties of nickel and nickel silicide films were examined by X-ray diffractometer (XRD) with various deposition temperatures. The interface properties and the surface morphology of nickel silicide films were studied by using Auger electron spectroscopy (AES) depth profile analyses and scanning electron microscopy (SEM). The experimental results showed that the iodine-catalyzed silicide film, which have a clean and smooth interface, exhibit lower resistivity, and lower leakage current density compared to that of non iodine-catalyzed films in implemented n⁺/p junction diode.     

Transmission electron microscopy study of Ni–Si nanocomposite films

Nickel induced crystallization of amorphous Si (a-Si) films is investigated using transmission electron microscopy. Metal-induced crystallization was achieved on layered films deposited onto thermally oxidized Si(3 1 1) substrates by electron beam evaporation of a-Si (400 nm) over Ni (50 nm). The multi-layer stack was subjected to post-deposition annealing at 200 and 600 °C for 1 h after the deposition. Microstructural studies reveal the formation of nanosized grains separated by dendritic channels of 5 nm width and 400 nm length. Electron diffraction on selected points within these nanostructured regions shows the presence of face centered cubic NiSi₂ and diamond cubic structured Si. Z-contrast scanning transmission electron microscopy images reveal that the crystallization of Si occurs at the interface between the grains of NiSi₂ and a-Si. X-ray absorption fine structure spectroscopy analysis has been carried out to understand the nature of Ni in the Ni–Si nanocomposite film. The results of the present study indicate that the metal induced crystallization is due to the diffusion of Ni into the a-Si matrix, which then reacts to form nickel silicide at temperatures of the order of 600 °C leading to crystallization of a-Si at the silicide–silicon interface.     

Synthesis and characterization of NiO-YSZ for SOFCs

Nickel oxide and yttria-stabilized zirconia ceramic materials were prepared by three methods: physical mixture, a modified Pechini route, and impregnation with Ni(NO₃)₂·6H₂O. Temperature-programmed reduction (TPR) analysis showed the presence of different reduction peaks for each sample and that the reduction temperature was influenced by the employed preparation procedure. Nickel oxide species are completely reduced at temperatures up to 1000 °C and their temperature-programmed reduction profiles indicated that a higher temperature reduction corresponds to a higher calcination temperature. Furthermore, the composites synthesized through impregnation presented nickel oxide species more easily reducible than those prepared by the two other methods. Scanning electron microscopy and X-ray photoelectron spectroscopy (XPS) evidenced a larger nickel oxide coating on yttria-stabilized zirconia for the composite synthesized through the impregnation method. The electrical conductivity of impregnation sample was 117 S cm⁻¹ at 850 °C, a value three times higher than that of the physical mixture.     

Optical properties of nanocrystalline SnS2 thin films

Thin films of nanocrystalline SnS₂ on glass substrates were prepared from solution by dip coating and then sulfurized in H₂S (H₂S:Ar = 1:10) atmosphere. The films had an average thickness of 60 nm and were characterized by X-ray diffraction studies, scanning electron microscopy, EDAX, transmission electron microscopy, UV-vis spectroscopy, and Raman spectroscopy. The influence of annealing temperature (150-300 °C) on the crystallinity and particle size was studied. The effect of CTAB as a capping agent has been tested. X-ray diffraction analysis revealed the polycrystalline nature of the films with a preferential orientation along the c-axis. Optical transmission spectra indicated a marked blue shift of the absorption edge due to quantum confinement and optical band gap was found to vary from 3.5 to 3.0 eV with annealing temperature. Raman studies indicated a prominent broad peak at ∼314 cm⁻¹, which confirmed the presence of nanocrystalline SnS₂ phase.     

Transparent conducting properties of Ni doped zinc oxide thin films prepared by a facile spray pyrolysis technique using perfume atomizer

Undoped and Ni doped zinc oxide (Ni–ZnO) thin films were prepared by a facile spray pyrolysis technique using perfume atomizer from aqueous solution of anhydrous zinc acetate (Zn(CH₃COOH)₂ and hexahydrated nickel chloride (NiCl₂·6H₂O) as sources of zinc and nickel, respectively. The films were deposited onto the amorphous glass substrates kept at (450 °C). The effect of the [Ni]/[Zn] ratio on the structural, morphological, optical and electrical properties of Ni doped ZnO thin film was studied. It was found from X-ray diffraction (XRD) analysis that both the undoped and Ni doped ZnO films were crystallized in the hexagonal structure with a preferred orientation of the crystallites along the [002] direction perpendicular to the substrate. The scanning electron microscopy (SEM) images showed a relatively dense surface structure composed of crystallites in the spherical form whose average size decreases when the [Ni]/[Zn] ratio increases. The optical study showed that all the films were highly transparent. The optical transmittance in the visible region varied between 75 and 85%, depending on the dopant concentrations. The variation of the band gap versus the [Ni]/[Zn] ratio showed that the energy gap decreases from 2.95 to 2.72 eV as the [Ni]/[Zn] ratio increases from 0 to 0.02 and then increases to reach 3.22 eV for [Ni]/[Zn] = 0.04. The films obtained with the [Ni]/[Zn] ratio = 0.02 showed minimum resistivity of 2 × 10⁻³ Ω cm at room temperature.     

Size-controlled synthesis, microstructure and magnetic properties of Ni nanoparticles

Ni nanoparticles with different mean diameters of 15-83 nm were synthesized by solution reduction process. The size of Ni nanoparticles can be controlled by varying the concentration of NiCl₂·6H₂O and synthesis temperature. The samples were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), infrared spectroscopy (IR) and X-ray photoelectron spectroscopy (XPS). Results show that the synthesized particles are single-phased Ni with a face-centered cubic crystal structure. Magnetic measurements indicate that Ni nanoparticles are ferromagnetic. The lattice constants and coercivities of the samples are size-dependent.     

High frequency magnetic mechanism of Ni-substituted Co2Z hexagonal ferrite

The magnetic properties, especially the high frequency magnetic mechanism, of Ni-substituted Co₂Z hexagonal ferrite were studied. The polycrystalline Z-type hexagonal ferrite of Ba₃Ni_xCo_2−xFe₂₄O₄₁ (0 ≤ x ≤ 2) were prepared by solid-state reaction. The results indicate that Ni-substituted Co₂Z samples all exhibit typical soft magnetic character. Substitution of Ni for Co will turn the planar magnetocrystalline anisotropy of Co₂Z to uniaxial anisotropy when x ≥ 1, so that the permeability drops dramatically and domain wall resonance appears in the frequency spectra. With the rise of Ni amount or sintering temperature, domain wall resonance strengthens gradually.     

Preparation and characterization of Co-B flowers with mesoporous structure

Co-B flowers with mesoporous structure were first prepared via reduction of cobalt acetate by potassium borohydride in the presence of complexing agent ethylenediamine. The as-prepared Co-B flowers were characterized by Fourier transform infrared spectroscopy, X-ray powder diffraction, scanning electron microscopy, transmission electron microscopy, inductively coupled plasma atomic emission spectroscopy, X-ray photoelectron spectroscopy, N₂ adsorption-desorption, and magnetic performance test. The Co-B flowers exhibited enhanced coercivity, and weakened saturation magnetization and remanet magnetization as compared with the regular Co-B. During the hydrolysis of KBH₄, the Co-B flowers exhibited higher catalytic activity than the regular Co-B. It is attributed to the larger specific surface area and mesoporous channels. During the successive reactions, the conversion of KBH₄ over Co-B flowers was about 97%. The average H₂ generation rate of Co-B flowers was 4620 mL/min/g-catalyst in 1.5 wt% NaOH + 15 wt% KBH₄ solution, which may give a successive H₂ supply for a 748 W polymer electrolyte membrane fuel cell (PEMFC) at 100% H₂ utilization.     

Facile fabrication of SiO2/Al2O3 composite microspheres with a simple electrostatic attraction strategy

SiO₂/Al₂O₃ composite microspheres with SiO₂ core/Al₂O₃ shell structure and high surface area were prepared by depositing Al₂O₃ colloid particles on the surface of monodispersed microporous silica microspheres using a simple electrostatic attraction and heterogeneous nucleation strategy, and then calcined at 600 °C for 4 h. The prepared products were characterized with differential thermal analysis and thermogravimetric analysis (DTA/TG), scanning electron microscopy (SEM), transmission electron microscopy (TEM), nitrogen adsorption and X-ray photoelectron spectroscopy (XPS). It was found that uniform alumina coating could be deposited on the surface of silica microspheres by adjusting the pH values of the reaction solution to an optimal pH value of about 6.0. The specific surface area and pore volume of the SiO₂/Al₂O₃ composite microspheres calcined at 600 °C were 653 m² g⁻¹ and 0.34 ml g⁻¹, respectively.     

Structural and magnetic properties of Mn nanoparticles prepared by arc-discharge

Mn nanoparticles are prepared by arc discharge technique. MnO, α-Mn, β-Mn, and γ-Mn are detected by X-ray diffraction, while the presence of Mn₃O₄ and MnO₂ is revealed by X-ray photoelectron spectroscopy. Transmission electron microscopy observations show that most of the Mn nanoparticles have irregular shapes, rough surfaces and a shell/core structure, with sizes ranging from several nanometers to 80 nm. The magnetic properties of the Mn nanoparticles are investigated between 2 and 350 K at magnetic fields up to 5 T. A magnetic transition occurring near 43 K is attributed to the formation of the ferrimagnetic Mn₃O₄. The coercivity of the Mn nanoparticles, arising mainly from Mn₃O₄, decreases linearly with increasing temperature below 40 K. Below the blocking temperature T_B ≈ 34 K, the hysteresis loops exhibit large coercivity (up to 500 kA/m), owing to finite size effects, and irreversibility in the loops is found up to 4 T, and magnetization is not saturated up to 5 T. The relationship between structure and the magnetic properties are discussed.     

Preparation and characterization of Chitosan/Konjac glucomannan/CdS nanocomposite film with low infrared emissivity

Novel organic-inorganic nanocomposite films were prepared with Chitosan (CS), Konjac glucomannan (KGM) and CdS by one-step synthesis. As-prepared films were characterized by IR spectra, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and infrared emissometer (IR). The results indicated that grown CdS dendrites were formed with reaction time of 12 h for Cd²⁺ and CS/KGM, and were well dispersed in CS/KGM with an average diameter of 40 nm. The CS/KGM/CdS nanocomposite films had significantly low infrared emissivity. When the mole ratio of CdS to summation of CS&KGM construction units was 1.0 with CdS size of 10-20 nm, the film got the lowest infrared emissivity value of 0.011, which could be attributed to the strong synergism effect existing between CS/KGM and CdS dendrites.     

Variable temperature in situ X-ray diffraction study of mechanically activated synthesis of calcium titanate, CaTiO3

The effect of mechanical activation on formation of calcium titanate (CaTiO₃) from calcined mixtures of CaCO₃ and TiO₂ was studied by monitoring the course of this solid-state reaction by variable temperature in situ X-ray diffraction (XRD) experiments, scanning electron microscopy (SEM) and dilatometry. Two equimolar mixtures of powdered CaCO₃ and TiO₂ were prepared: one was mechanically activated by grinding in a high energy vibro-mill. A total of 32 X-ray diffraction data sets for each sample, collected between 30 and 1100 °C, were analyzed by multiphase Rietveld refinement. Quantitative phase analysis and microstructure analysis obtained from X-ray diffraction are correlated to results of scanning electron microscopy and dilatometry. In the non-activated sample, small quantities of the reactants remain in the product until 1100 °C. In the activated sample, the reaction results in pure CaTiO₃ at 920 °C.     

New lead vanadium phosphate with langbeinite-type structure: Pb1.5V2(PO4)3

The new lead vanadium phosphate Pb_1.5V₂(PO₄)₃ was synthesized by solid state reaction and characterized by X-ray powder diffraction, electron microscopy, and magnetic susceptibility measurements. The crystal structure of Pb_1.5V₂(PO₄)₃ (a = 9.78182(8) Å, S.G. P2₁3, Z = 4) was determined from X-ray powder diffraction data and belongs to the langbeinite-type structures. It is formed by corner-linked V³⁺O₆ octahedra and tetrahedral phosphate groups resulting in a three-dimensional framework. The lead atoms are situated in the structure interstices and only partially occupy their positions. An electron microscopy study confirmed the structure solution. Magnetic susceptibility measurements revealed Curie-Weiss (CW) behavior for Pb_1.5V₂(PO₄)₃ at high temperature whereas at around 14 K an abrupt increase on the susceptibility was observed.     

Electrodeposition of As2Se3 thin films

Semiconducting As₂Se₃ thin films have been prepared from an aqueous bath at room temperature onto stainless steel and fluorine-doped tin oxide (F.T.O.)-coated glass substrates using an electrodeposition technique. It has been found that As₂O₃ and SeO₂ in the volumetric proportion as 4:6 and their equimolar solutions of 0.075 M concentration forms good quality films of As₂Se₃. The films are annealed in a nitrogen atmosphere at temperature of 200 °C for 2 h. The films are characterised by scanning electron microscopy, X-ray diffraction and optical absorption techniques. Studies reveal that asdeposited and annealed thin films are polycrystalline in nature. The optical band gap has been found to be 2.15 eV for the above-mentioned composition and concentration of the film.     

CuSn(OH)6 submicrospheres: Room-temperature synthesis, growth mechanism, and weak antiferromagnetic behavior

CuSn(OH)₆ submicrospheres with diameters of 400-900 nm have been successfully fabricated using a simple aqueous solution method at room temperature. Influencing factors such as the dosage of reactants and reaction time on the preparation were systematically investigated. The products were characterized with X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), thermogravimetric analysis (TG) and differential thermal analysis (DTA). Results reveal that the CuSn(OH)₆ spheres are built from numerous nanoparticles. It is found that the diameter of CuSn(OH)₆ spheres can be readily tuned by adjusting the molar ratio of to Cu²⁺. A possible growth mechanism for the CuSn(OH)₆ submicrospheres has been proposed. Amorphous CuSnO₃ submicrospheres were obtained after thermal treatment of the CuSn(OH)₆ submicrospheres at 300 °C for 4 h. Standard magnetization measurements demonstrate that the CuSn(OH)₆ submicrospheres are antiferromagnetic and have a weak spin-Peierls transition at about 78 K.     

Fabrication of luminescent SrWO4 thin films by a novel electrochemical method

Highly crystallized SrWO₄ thin films with single scheelite structure were prepared within 60 min by a cell electrochemical method. X-ray diffraction analysis shows that SrWO₄ thin films have a tetragonal structure. Scanning electron microscopy examinations reveal that SrWO₄ grains grow well in tetragonal tapers and grains like flowers or bunches, which can usually form by using the electrolysis electrochemical method, have disappeared under cell electrochemical conditions. X-ray photoelectron spectra and energy dispersive X-ray microanalysis examinations demonstrate that the composition of the film is consistent with its stoichiometry. These SrWO₄ films show a single blue emission peak (located at 460 nm) using an excitation wave of 230 nm. The speed of cell electrochemical method can be controlled by changing temperature. The optimum treatment temperature is about 50-60 °C.     

Fabrication of antiferroelectric PLZT films on metal foils

Fabrication of high-dielectric-strength antiferroelectric (AFE) films on metallic foils is technically important for advanced power electronics. To that end, we have deposited crack-free Pb_0.92La_0.08Zr_0.95Ti_0.05O₃ (PLZT 8/95/5) films on nickel foils by chemical solution deposition. To eliminate the parasitic effect caused by the formation of a low-permittivity interfacial oxide, a conductive buffer layer of lanthanum nickel oxide (LNO) was coated by chemical solution deposition on the nickel foil before the deposition of PLZT. Use of the LNO buffer allowed high-quality film-on-foil capacitors to be processed in air. With the PLZT 8/95/5 deposited on LNO-buffered Ni foils, we observed field- and thermal-induced phase transformations of AFE to ferroelectric (FE). The AFE-to-FE phase transition field, E_AF = 225 kV/cm, and the reverse phase transition field, E_FA = 190 kV/cm, were measured at room temperature on a ≈1.15 μm-thick PLZT 8/95/5 film grown on LNO-buffered Ni foils. The relative permittivities of the AFE and FE states were ≈600 and ≈730, respectively, with dielectric loss ≈0.04 at room temperature. The Curie temperature was ≈210 °C. The thermal-induced transition of AFE-to-FE phase occurred at ≈175 °C. Breakdown field strength of 1.2 MV/cm was measured at room temperature.     

Preparation of high nickel-containing MCM-41-type mesoporous silica via a modified direct synthesis method

A method with modifying tetraethyl orthosilicate (TEOS) with nickel species has been developed for the synthesis of mesoporous silica with high nickel content (11.8 wt.% of Ni or even higher). With the method, MCM-41-type materials were obtained with high BET surface area reaching 868 m²/g and pore volume up to 0.73 cm³/g. The materials were characterized by means of X-ray powder diffraction, transmission electron microscopy, energy dispersive X-ray spectroscopy, N₂ adsorption, Fourier transform infrared and X-ray photoelectron spectroscopy. Nickel species were incorporated into the silica frameworks. The mesostructures still remain after activation using H₂ at 773 K.