Oxide-ion conductivity in CuxCe1−xO2−δ (0 ≤ x ≤ 0.10)

Up to 10 at.% of copper readily substitutes for cerium in ceria. It is found that at oxygen partial pressures between 0.21 atm and 10⁻⁵ atm, Cu_xCe_1−xO_2−δ (0 ≤ x ≤ 0.10) solid solution behave as an oxide-ion electrolyte. Interestingly, Cu_0.10Ce_0.90O_2−δ exhibits the oxide-ion conductivity of ca. 10⁻⁴ Ω⁻¹ cm⁻¹ at 600 °C at an oxygen partial pressure of 10⁻⁵ atm.     

Electrical transport and structural study of CuCr1 − xMgxO2 delafossite thin films grown by pulsed laser deposition

The growth and properties of delafossites CuCr_1 − xMg_xO₂ thin films are examined. These films are grown by pulsed laser deposition. As a class of materials delafossites have received recent interest since some members show p-type behavior. While not considered true wide-bandgap materials due to a narrow indirect bandgap that fails to adsorb light due to a forbidden same parity transition, optical transparencies greater than 40% in the visible can be observed. In order to be useful for transparent device applications, CuCr_1 − xMg_xO₂ films are needed with low resistivity and high optical transparency. Epitaxial films of CuCr_1 − xMg_xO₂ were grown on c-sapphire, examining the effects of oxygen pressure and growth temperature on film properties. Films were realized with resistivity of ~ 0.02 Ω-cm and optical transparency of 40% in the visible. The formation of a problematic secondary minority spinel phase of (Cu,Mg)Cr₂O₄ is discussed. While conductivity increases substantially with Mg doping, the incidence of the spinel phase increases as well.     

Itinerant ferromagnetism to insulating spin glass in SrRu1−xCuxO3 (0 ≤ x ≤ 0.3)

The ferromagnetic metallic oxide, SrRuO₃ (T_C ∼ 165 K) undergoes structural, magnetic and metal-insulator transitions upon substitution of Cu at the Ru-site. For x = 0.2 in SrRu_1−xCu_xO₃, the structure becomes a tetragonal with the space group I4/mcm and there is a signature of both ferromagnetic (T_C = 65 K) and antiferromagnetic (T_N = 32 K) ordering due to possible magnetic phase separation. The antiferromagnetism arises due to short range ordering of Cu- and Ru-moments. Jahn-Teller distortion of (Ru,Cu)-O₆ octahedra indicates that the copper ions are in 2+ oxidation state with ⁶t2g³eg electronic configuration. For x ≥ 0.1, narrowing of Ru-4d bandwidth by the substitution of Cu ions results in semiconducting behavior. For x = 0.3, the ac and dc susceptibility measurements indicate a spin glass behavior. The origin of spin glass behavior has been attributed to competing ferromagnetic and antiferromagnetic interactions.     

Eu-Mössbauer spectroscopic and X-ray diffraction study on EuyM1−yO2−x (0 ≤ y ≤ 1.0) (M = Th, U)

¹⁵¹Eu-Mössbauer spectroscopic and powder X-ray diffraction (XRD) study has been performed for the Eu_yM_1−yO_2−x (M = Th and U) systems over the entire composition range of 0 ≤ y ≤ 1.0. The XRD results of the Eu-Th system showed that a very wide defect-fluorite (DF) type phase in which oxygen vacancies (V_O) are disordered (x = y/2) is formed for 0 ≤ y < 0.5 and that two-phase regions sandwitching a narrow C-type (C) single phase around y ≈ 0.8 appear for 0.5 < y < 0.8 (DF + C) and 0.82 < y < 1.0 (C + B-type (monoclinic) Eu₂O₃). The Mössbauer results show that the isomer shifts (ISs) of Eu³⁺ in this system smoothly increase with Eu composition, y. The decrease of average coordination number (CN) of O²⁻ around Eu³⁺ with increasing y (CN = 8 − 2y) (x = y/2) results in the decrease of the average EuO bond length, which is due to the decrease of repulsion force between O²⁻ anions. This result confirms that the IS of Eu³⁺ correlates well with the average EuO bond length in oxide systems. For the Eu-U system, the lattice parameter, a₀, of the system decreases almost linearly with y, in accordance with the calculated a₀ versus y curve for the oxygen-stoichiometric (i.e. x = 0) fluorite-type dioxide (CN = 8). The ISs of Eu³⁺ in this composition range remain almost constant around 0.5 mm/s, which is comparable to those of pyrochlore oxides (Eu₂Zr₂O₇ and Eu₂Hf₂O₇ (y = 0.5)) with O²⁻-eight-fold coordinated Eu³⁺(CN = 8).     

Study on the optical properties of Zn1−xMgxS (0 ≤ x ≤ 0.55) quantum dots prepared by precipitation method

Zn_1−xMg_xS (0 ≤ x ≤ 0.55) quantum dots (QDs) were successfully synthesized by precipitation method. The crystal structures, microstructures, and optical properties of the Zn_1−xMg_xS QDs were investigated using X-ray diffraction, scanning electron microscopy, and ultraviolet-visible and photoluminescence (PL) spectroscopy. The Zn_1−xMg_xS QDs were found to have a cubic crystal structure and an average crystallite size of 6.40-7.96 nm. It has been shown that an increase in doping Mg²⁺ concentration in Zn_1−xMg_xS QDs led to a gradual widening of the band gap and a weakening in the PL intensity of the Zn_1−xMg_xS QDs.     

Effect of crystallization quality on ferromagnetism in Zn1 − xCoxO nanopowders

In this paper, a series of Zn_1 − xCo_xO nanocrystals with different cobalt percentages were fabricated by a simple chemical method, which were intensively explored for spintronics applications. X-ray diffraction (XRD), ultraviolet-visible (UV-Vis) spectrophotometer, transmission electron microscope (TEM) and vibrating sample magnetometer (VSM) were used to characterize the structures and magnetic properties of prepared samples. It was concluded that Co²⁺ was well inserted into ZnO wurtzite structure. The ferromagnetism of Zn_1 − xCo_xO nanopowders was observed at room temperature. The relation between crystallization quality and magnetism of Zn_1 − xCo_xO nanopowders was discussed in detail. It was demonstrated the crystallization quality of Zn_1 − xCo_xO nanocrystals had a strong effect on the ferromagnetism.     

Influence of SnO2 addition on the thermoelectric properties of Zn1 − xSnxO (0.01 ≤ x ≤ 0.05)

The grain size and the density of the Zn_1 − xSn_xO (0 ≤ x ≤ 0.05) samples decreased with increasing SnO₂ content. The addition of a small amount of SnO₂ (x ≤ 0.01) to ZnO led to an increase in both the electrical conductivity and the absolute value of the Seebeck coefficient, resulting in a significant increase in the power factor. The thermoelectric power factor was maximized to a value of 1.25 × 10⁻³ Wm⁻¹ K⁻² at 1073 K for the Zn_0.99Sn_0.01O sample.     

Electron paramagnetic resonance (EPR) of antiferromagnetic nanoparticles of La1−xSrxCrO3 (0.000 ≤ x ≤ 0.020) synthesized by combustion reaction

Nanocrystalline particles of La_1−xSr_xCrO₃ (0.000 ≤ x ≤ 0.020) compounds were synthesized in order to investigate the antiferromagnetic (AFM) to paramagnetic (PM) phase transition temperature, g-factor, line width and intensity by electron paramagnetic resonance (EPR). All samples were synthesized by combustion reaction method using strontium nitrate, lanthanum nitrate, chromium nitrate and urea as fuel without subsequent heat treatment. X-ray diffraction patterns of all systems showed broad peaks consistent with orthorhombic structure of LaCrO₃. The absence of extra reflections in the diffraction patterns of as-prepared materials ensures the phase purity. The average crystallite sizes determined from the prominent (1 1 2) peak of the diffraction using Scherrer's equation was independent of the addition of Sr²⁺ ions; being ca. 31–29 nm for x = 0.000 and 0.020, respectively. The EPR line width and intensity were found to be dependent on Sr²⁺ addition and temperature. However, the AFM–PM transition temperature was found to be independent of strontium concentration, being ca. 296 K. In the PM phase, g-factor was nearly temperature independent with increasing of x. The EPR results indicated that the addition of Sr²⁺ ions may induce creation of Cr³⁺–Cr⁴⁺ clusters.     

Synthesis of perovskite-type (La1−xCax)FeO3 (0 ≤ x ≤ 0.2) at low temperature

Gel formation was realized by adding citric acid to a solution of La(NO₃)₃·5H₂O, Ca(NO₃)₂·4H₂O, and Fe(NO₃)₂·9H₂O. Perovskite-type (La_1−xCa_x)FeO₃ (0 ≤ x ≤ 0.2) was synthesized by firing the gel at 500 °C in air for 1 h. The crystallite size (D_1 2 1) decreased with increasing x, while the specific surface area was 6.8-9.4 m²/g and independent of x. The XPS measurement of the (La_1−xCa_x)FeO₃ surface indicated that the Ca²⁺ ion content increased with increasing x, while the Fe ion content was independent of x. Catalytic activity for CO oxidation increased with increasing x.     

Structural and electrical properties of La2−xBaxMo2O9−x/2 (x = 0-0.18)

La_2−xBa_xMo₂O_9−x/2 (x ≤ 0.18) have been prepared by solid state reaction method. The lattice parameter of La_2−xBa_xMo₂O_9−x/2 (x ≤ 0.18) determined by XRD data refinement shows a linear dependence on the dopant Ba content x. For the specimen with a La/Ba molar ratio of 0.18-0.2, additional reflection of secondary phase exists in the XRD pattern, so the value of solubility limit for Ba in La₂Mo₂O₉ is defined in range of 0.18 < x < 0.2. As the replacement degree of La³⁺ by Ba²⁺ increases, the bulk conductivity of La_2−xBa_xMo₂O_9−x/2 (x ≤ 0.18) decreases initially and then increases, a minimum value at La_1.9Ba_0.1Mo₂O_8.95 exists. Hebb-Wagner studies in argon atmosphere, which use an oxide-ion blocking electrode, show that La_2−xBa_xMo₂O_9−x/2 (x ≤ 0.18) are predominantly oxide-ion conducting in the temperature ranging from 773 to 1173 K. The average thermal expansion coefficient of La_1.84Ba_0.16Mo₂O_8.92 determined by high-temperature XRD was deduced as great as 17.5 × 10⁻⁶ K⁻¹ between 298 and 1173 K.     

Order-disorder phase transitions and high-temperature oxide ion conductivity of Er2+xTi2−xO7−δ (x = 0, 0.096)

The Er_2+xTi_2−xO_7−δ (x = 0.096; 35.5 mol% Er₂O₃) solid solution and the stoichiometric pyrochlore-structured compound Er₂Ti₂O₇ (x = 0; 33.3 mol% Er₂O₃) are characterized by X-ray diffraction (phase analysis and Rietveld method), thermal analysis and optical spectroscopy. Both oxides were synthesized by thermal sintering of co-precipitated powders. The synthesis study was performed in the temperature range 650-1690 °C. The amorphous phase exists below 700 °C. The crystallization of the ordered pyrochlore phase (P) in the range 800-1000 °C is accompanied by oxygen release. The ordered pyrochlore phase (P) exists in the range 1000−1200 °C. Heat-treatment at T ≥ 1600 °C leads to the formation of an oxide ion-conducting phase with a distorted pyrochlore structure (P2) and an ionic conductivity of about 10⁻³ S/cm at 740 °C. Complex impedance spectra are used to separately assess the bulk and grain-boundary conductivity of the samples. At 700 °C and oxygen pressures above 10⁻¹⁰ Pa, the Er_2+xTi_2−xO_7−δ (x = 0, 0.096) samples are purely ionic conductors.     

Compositional dependence on the optical properties of amorphous As2 − xS3 − xSbx thin films

In this paper, we report results of the optical properties of thermally deposited As_2 − xS_3 − xSb_x thin films with x = 0.02, 0.07, 0.1 and 0.15. We have characterized the deposited films by Fourier Transform Infrared, Raman and X-ray photoelectron spectroscopy (XPS). The relationship between the structural and optical properties and the compositional variation were investigated. It was found that the optical bandgap decreases with increase in Sb content. The XPS core level spectra show a decrease in As₂S₃ percentage with increase in Sb content. This is confirmed from the shifting of the Raman peak from AsS₃ vibrational mode towards SbS₃ vibrational mode.     

Synthesis, structural and magnetic properties of La1−xCdxFeO3 (0.0 ≤ x ≤ 0.3) orthoferrites

Nanocrystalline La_1−xCd_xFeO₃ (0.0 ≤ x ≤ 0.3) solid solutions have been synthesized by a single-step solution combustion method at a relatively low temperature of 400 °C. The combustion-synthesized solid solutions were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), and magnetic measurements. The crystal structure examined by XRD indicates that the samples were single-phase, and crystallize in an orthorhombic (space group, Pbnm no. 62) structure. The parent and doped compounds showed canted antiferromagnetic behavior associated with an increase in magnetic moment with Cd doping. The changes in magnetic properties of the materials are correlated to the changes in structural features resulting from the Rietveld structural refinement of the materials.     

Structural and optical properties of polycrystalline CdSexTe1−x (0 ≤ x ≤ 0.4) thin films

CdSe_xTe_1−x (0 ≤ x ≤ 0.4) ternary thin films have been deposited on quartz substrates at room temperature by a single source thermal evaporation. X-ray diffraction patterns and transmission electron microscope micrographs of these films showed that the films were of polycrystalline texture over the whole range studied and exhibit predominant cubic (zinc blende) structure with strong preferential orientation of the crystallites along (1 1 1) direction. Linear variation of the lattice constant with mole fraction x is observed obeying Vegard's law. The dependence of the optical constants, the refractive index n and extinction coefficient k, of the films on the mole fraction x was studied in the spectral range of 400-2500 nm. The normal dispersion of the refractive index of the films could be described using the Wemple-DiDomenco single-oscillator model. CdSe_xTe_1−x thin films of different composition have two direct and indirect transitions corresponding to energy gaps and . The variation in either or with x indicates that this system belongs to the amalgamation type. The variation follows a subquadratic dependence and the bowing parameters were found to be 0.36 and 0.48 eV for the direct, and indirect energy gaps, respectively. Direct linear variation of the ratio N/m^* with x is observed.     

Structure and thermal conductivity of Gd2(TixZr1 − x)2O7 ceramics

The Gd₂(Ti_xZr_1 − x)₂O₇ (x = 0, 0.25, 0.50, 0.75, 1.00) ceramics were synthesized by solid state reaction at 1650 °C for 10 h in air. The relative density and structure of Gd₂(Ti_xZr_1 − x)₂O₇ were analyzed by the Archimedes method and X-ray diffraction. The thermal diffusivity of Gd₂(Ti_xZr_1 − x)₂O₇ from room temperature to 1400 °C was measured by a laser-flash method. The Gd₂Zr₂O₇ has a defect fluorite-type structure; however, Gd₂(Ti_xZr_1 − x)₂O₇ (0.25 ≤ x ≤ 1.00) compositions exhibit an ordered pyrochlore-type structure. Gd₂Zr₂O₇ and Gd₂Ti₂O₇ are infinitely soluable. The thermal conductivity of Gd₂(Ti_xZr_1 − x)₂O₇ increases with increasing Ti content under identical temperature conditions. The thermal conductivity of Gd₂(Ti_xZr_1 − x)₂O₇ first decreases gradually with the increase of temperature below 1000 °C and then increases slightly above 1000 °C. The thermal conductivity of Gd₂(Ti_xZr_1 − x)₂O₇ is within the range of 1.33 to 2.86 W m^− 1 K^− 1 from room temperature to 1400 °C.     

Structural and optical properties of rock-salt Cd1 − xZnxO thin films prepared by thermal decomposition of electrodeposited Cd1 − xZnxO2

Cd_1 − xZn_xO nanocrystalline thin films with rock-salt structure were obtained through thermal decomposition of Cd_1 − xZn_xO₂ (x = 0, 0.37, 0.57, 1) thin films which were electrodeposited from aqueous solution at room temperature. X-ray diffraction results showed that the Zn ions were incorporated into rock salt-structure of CdO and the crystal lattice parameters decreased with the increase of Zn contents. The bandgaps of the Cd_1 − xZn_xO thin films were obtained from optical transmission and were 2.40, 2.51, 2.63 and 3.25 eV, respectively.     

Sintering behavior, microstructure and microwave dielectric properties of Li2+xTiO3 (0 ≤ x ≤ 0.2)

Sintering behavior, microstructure and microwave dielectric properties of Li_2+xTiO₃ (0 ≤ x ≤ 0.2) ceramics have been studied by X-ray diffraction (XRD), scan electron microscopy (SEM), Raman spectra, dilatometery and microwave resonant measurement in this research. Homogeneous non-stoichiometric composition with rock salt structure existed for Li_2+xTiO₃ (0 ≤ x ≤ 0.2) ceramics. The sintering temperature was successfully reduced and highly densified sample could be obtained with appropriate excessive amount of lithium (x = 0.08). A transient reactive liquid phase sintering mechanism was proposed. The preferred orientation of grain growth and micro-cracks existed in the Li₂TiO₃ (x = 0) sample disappeared in the lithium excessive samples with x ≥ 0.08. The microwave dielectric properties varied significantly with the excessive amount of lithium. Optimized microwave dielectric properties were obtained for the x = 0.08 composition: ?_r = 24.6, Q × f = 66,000 GHz, and τ_f = 22.1 ppm/°C.     

Synthesis of spherical nanostructured LiMxMn2−xO4 (M = Ni, Co, and Ti; 0 ≤ x ≤ 0.2) via a single-step ultrasonic spray pyrolysis method and their high rate charge-discharge performances

LiM_xMn_2−xO₄ (M = Ni²⁺, Co³⁺, and Ti⁴⁺; 0 ≤ x ≤ 0.2) spinels were prepared via a single-step ultrasonic spray pyrolysis method. Comparative studies on powder properties and high rate charge-discharge electrochemical performances (from 1 to 15 C) were performed. XRD identified that pure spinel phase was obtained and M was successfully substituted for Mn in spinel lattice. SEM and TEM studies confirmed that powders had a feature of ‘spherical nanostructural’, that is, powders consisted of spherical secondary particles with the size of about 1 μm, which were developed from close-packed primary particles with several tens of nanometers. Substitutions enhanced density of second particles to different extents, depending on M and its content. Charge-discharge tests showed that as-prepared LiMn₂O₄ could deliver excellent rate performance (around 100 mAh/g at 10 C). Ni substitution contributed to improving electrochemical performances. In the voltage range of 4.95-3.5 V, the materials showed much better electrochemical performances than LiMn₂O₄ in terms of capacity, cycleability and rate capability.     

Double subband occupation of the two-dimensional electron gas in InxAl1 − xN/AlN/GaN/AlN heterostructures with a low indium content (0.064 ≤ x ≤ 0.140) barrier

We present a carrier transport study on low indium content (0.064 ≤ x ≤ 0.140) In_xAl_1 − xN/AlN/GaN/AlN heterostructures. Experimental Hall data were carried out as a function of temperature (33-300 K) and a magnetic field (0-1.4 T). A two-dimensional electron gas (2DEG) with single or double subbands and a two-dimensional hole gas were extracted after implementing quantitative mobility spectrum analysis on the magnetic field dependent Hall data. The mobility of the lowest subband of 2DEG was found to be lower than the mobility of the second subband. This behavior is explained by way of interface related scattering mechanisms, and the results are supported with a one-dimensional self-consistent solution of non-linear Schrödinger-Poisson equations.     

Synthesis of three dimensional photoluminescent [In10S20 − xSex] supertetrahedral clusters: (x < 0.3)

Two strong solid state luminescence peaks, centered at 457 nm and 538 nm, were observed from the newly synthesized ternary [In₁₀S_20 − xSe_x]¹⁰⁻ T3 clusters, under excitation by UV radiation (λ = 360 nm). The 457 nm peak is due to the porosity property of T3 clusters. Nevertheless, the 538 nm peak has not been reported for the T3 clusters before. In this letter, we demonstrate that the 538 nm peak is attributed to the trace Se atoms confined in the [In₁₀S_20 − xSe_x]¹⁰⁻ clusters. The luminescent output from the ternary [In₁₀S_20 − xSe_x]¹⁰⁻ T3 clusters is independent of temperature from 298 K until 77 K.