Silver nanoparticles: Large scale solvothermal synthesis and optical properties

Silver nanoparticles have been successfully synthesized by a simple and modified solvothermal method at large scale using ethanol as the refluxing solvent and NaBH₄ as reducing agent. The nanopowder was investigated by means of X-ray diffraction (XRD), transmission electron microscopy (TEM), dynamic light scattering (DLS), UV-visible and BET surface area studies. XRD studies reveal the monophasic nature of these highly crystalline silver nanoparticles. Transmission electron microscopic studies show the monodisperse and highly uniform nanoparticles of silver of the particle size of 5 nm, however, the size is found to be 7 nm using dynamic light scattering which is in good agreement with the TEM and X-ray line broadening studies. The surface area was found to be 34.5 m²/g. UV-visible studies show the absorption band at ∼425 nm due to surface plasmon resonance. The percentage yield of silver nanoparticles was found to be as high as 98.5%.     

Zinc oxide micro- and nanoparticles: Synthesis, structure and optical properties

Zinc oxide (ZnO) spherical nanoparticles (SNPs) and bitter-melon-like (BML) microparticles were synthesized by a hydrothermal route using a zinc (Zn) plate as a source and substrate at various synthesis conditions. The structural analysis confirmed the formation of ZnO with hexagonal wurtzite phase on the hexagonal Zn substrate with growth of the ZnO microparticles along the [1 0 1] direction. The UV-vis absorption spectra of the ZnO microparticles indicated absorption peaks in the UV region which can be attributed to the band gap of ZnO. The room temperature photoluminescence (PL) of the ZnO microparticles exhibited a broad emission band, which is fitted with four Gaussian peaks and were assigned to transitions involving free excitons and various defect centers. The growth model for the formation of ZnO micro- and nanoparticles is presented.     

Dopant induced variations in microstructure and optical properties of CeO2 nanoparticles

Nanocrystalline CeO₂ particles doped in the range of 0-20% of Ca²⁺, La³⁺, and Zr⁴⁺ have been prepared from hydrothermal synthesis of nitrate solutions at 200 °C and the influences of the dopants on microstructure and optical properties of the nanoparticles have been investigated. The unit cell parameter is found to be modified by −0.39, +0.83 and +0.16% for doping of 20% Zr⁴⁺, La³⁺, and Ca²⁺, respectively. For each batch prepared, nanoparticles with a narrow size distribution of 5-15 nm have been obtained. A high-resolution transmission electron microscopy investigation reveals that these particles are single crystals mostly having hexagonal, square or circular two-dimensional projections. UV-visible spectra of doped powders exhibit shift of the absorption edge and absorption peak with respect to those of the undoped CeO₂ particles and has been attributed to compensation of Ce³⁺ and decreasing crystallite size as result of doping.     

Low temperature synthesis of porous copper/zinc oxide

A two-step urea aqueous solution process at a low temperature (90 °C) was employed for the preparation of a copper/zinc oxide material. Well defined porous spherical particles with average sizes of around 5 μm in diameter were prepared first and then used as a support for further copper-zinc precipitation. It was found that the particle composition and shape were changed with applied stirring speed (100 rpm or 200 rpm) and that particle size is inversely proportional to the copper content in the particles. The particles preserved their size and shape after the heat treatment. Prepared Cu/ZnO samples showed catalytic activity for the reaction of steam reforming of methane. Samples were characterized by scanning field emission electron microscopy, energy dispersive X-ray analyses, X-ray powder diffraction, surface area analyses, and atomic absorption spectroscopy.     

Studies on the structural and optical properties of zinc oxide nanobushes and Co-doped ZnO self-aggregated nanorods synthesized by simple thermal decomposition route

Pure and Co-doped zinc oxide nanomaterials were prepared by a simple low temperature synthesis and were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), high resolution-transmission electron microscopy (HR-TEM), diffused reflectance spectroscopy (DRS) and electron paramagnetic resonance (EPR) techniques. The results showed the formation of nanobushes that consists of several nanowires for pure ZnO and the nanorods formed by self-aggregation for Co-doped ZnO. The presence of Co²⁺ ions replacing some of the Zn²⁺ in the ZnO lattice was confirmed by EPR and DRS studies. The mechanism for the formation of self-aggregated and self-aligned ZnO rods after the incorporation of cobalt in the lattice by the building block units is discussed in this study. Morphological studies were carried out using SEM and HR-TEM, which supports the validity of the proposed mechanism for the formation of ZnO nanobushes and Co-doped ZnO nanorods. The synthesized nanomaterials were found to have good optoelectronic properties.     

Sonochemical synthesis of ZnO nanoparticles: The effect of temperature and sonication power

ZnO nanoparticles were synthesized by drop-wise addition of ZnCl₂ solution to KOH, in different temperatures and sonication output powers. The morphologies and structure of resulting materials were characterized by means of X-ray diffraction (XRD) and scanning electron microscopy (SEM). The morphology of the products was determined to be a mixture of nano rods as well as nanoparticles depending to sonication output power and temperature. A reduction in nanoparticles and aggregates sizes as well as amount of byproducts was observed by increasing the sonication output power. A combination of sonication output power and temperature was also studied on the properties of the product. At 70 °C and 45 W sonication output power, the smallest nanoparticles as well as narrower range of sizes in addition to minimum amount of byproducts was obtained in this work.     

Structural properties and growth mechanism of flower-like ZnO structures obtained by simple solution method

Flower-shaped zinc oxide (ZnO) structures have been synthesized in the reaction of aqueous solution of zinc nitrate and NaOH at 90 °C. To examine the morphology of ZnO nanostructures, time-dependent experiments were carried out. Detailed structural observation showed that the flower-like structures consist of triangular-shaped leaves, having sharpened tips with wider bases. Photoluminescence spectrum measured at room temperature show a sharp UV emission at 381 nm and a strong and broad green emission at 480-750 nm attributed to structural defects. A possible growth mechanism for the formation of flower-shaped ZnO structures is discussed in detail.     

Vanadium dioxide nanobelts: Hydrothermal synthesis and magnetic properties

VO₂ (B) nanobelts were prepared by a hydrothermal method at 180 °C using V₂O₅·nH₂O sol and H₂C₂O₄·2H₂O as starting agents. The obtained nanobelts have diameters ranging from 50 to 100 nm in width, 20-30 nm in thickness with lengths up to 1.5 μm. Measurements of the static magnetic susceptibility provide evidence for two phase transitions at T₁ = 225 K and T₂ = 290 K, respectively. Below T₁, the data suggest the presence quasi-free as well as of strongly antiferromagnetic correlated spins associated to V⁴⁺-ions.     

Hydrothermal synthesis and properties of solid solutions and composite nanoparticles in the TiO2-SnO2 system

Solid solutions and composite nanoparticles in the TiO₂-SnO₂ system were directly formed via the hydrothermal treatment of precursor solutions of TiCl₄ and SnCl₄ under weakly basic conditions in the presence of urea. The rutile-type (Ti, Sn)O₂ solid solutions were formed in the composition range of Ti 0-70 mol%. The composite nanoparticles consisting of anatase- and rutile-type phases were formed at the composition of Ti 80 and Ti 90 mol%. The change in the lattice parameters a₀ and c₀ of the rutile-type solid solutions followed the Vegard Law. The crystallite size of the rutile-type solid solutions was in the range of 5-10 nm. The diffuse reflectance spectra varied with changing Ti content in the precipitates. The photocatalytic activity of composite nanoparticles synthesized at 240 °C was higher than that synthesized at 180 °C. The composite nanoparticles consisting of anatase- and rutile-type phases with compositions Ti_0.90Sn_0.10O₂ and Ti_0.80Sn_0.20O₂ showed improved photocatalytic activity.     

Towards thiol functionalization of vanadium pentoxide nanotubes using gold nanoparticles

Template-directed synthesis is a promising route to realize vanadate-based 1-D nanostructures, an example of which is the formation of vanadium pentoxide nanotubes and associated nanostructures. In this work, we report the interchange of long-chained alkyl amines with alkyl thiols. This reaction was followed using gold nanoparticles prepared by the Chemical Liquid Deposition (CLD) method with an average diameter of ∼0.9 nm and a stability of ∼85 days. V₂O₅ nanotubes (VOx-NTs) with lengths of ∼2 m and internal hollow diameters of 20-100 nm were synthesized and functionalized in a Au-acetone colloid with a nominal concentration of ∼4×10⁻³ mol dm⁻³. The interchange reaction with dodecylamine is found only to occur in polar solvents and incorporation of the gold nanoparticles is not observed in the presence of n-decane.     

CeO2 nanocrystals: Seed-mediated synthesis and size control

This work reports on seed-mediated synthesis and size control of monodispersed CeO₂ nanoparticles. CeO₂ nanoparticles of mean size smaller than 2 nm were first prepared by a simple mixing of aqueous solution of cerium (IV) sulfate and ammonia solution at ambient conditions. Using these as-prepared fine particles as the tiny seeds, tunable sizes of CeO₂ nanoparticles were achieved via a facile hydrothermal treatment. All samples were characterized by X-ray diffraction (XRD), infrared (IR) spectroscopy, UV-vis spectroscopy, and thermogravimetric analysis (TGA). It is shown that in comparison with other inorganic cerium salts such as cerium (III) nitrates, cerium (IV) sulfate appears more suitable for forming CeO₂ nanoparticles at room temperature. Sulfate groups are strongly thermodynamically adsorbed on CeO₂ nanoparticle surfaces. The formation mechanism, surface hydration and sulfation characteristics of the resulting CeO₂ nanoparticles are also discussed.     

Electrical and gas sensing properties of self-aligned copper-doped zinc oxide nanoparticles

Electrical and gas sensing properties of nanocrystalline ZnO:Cu, having Cu X wt% (X = 0.0, 0.5, 1.0, and 1.5) in ZnO, in the form of pellet were investigated. Copper chloride and zinc acetate were used as precursors along with oxalic acid as a precipitating reagent in methanol. Material characterization was done by X-ray diffraction (XRD), scanning electron microscopy (SEM), field emission scanning electron microscopy (FE-SEM) and inductive coupled plasma with optical emission spectrometry (ICP-OES). FE-SEM showed the self-aligned Cu-doped ZnO nano-clusters with particles in the range of 40-45 nm. The doping of 0.5% of copper changes the electrical conductivity by an order of magnitude whereas the temperature coefficient of resistance (TCR) reduces with increase in copper wt% in ZnO. The material has shown an excellent sensitivity for the H₂, LPG and CO gases with limited temperature selectivity through the optimized operating temperature of 130, 190 and 220 °C for H₂, LPG and CO gases, respectively at 625 ppm gas concentration. The %SF was observed to be 1460 for H₂ at 1% Cu doping whereas the 0.5% Cu doping offered %SF of 950 and 520 for CO and LPG, respectively. The response and recovery time was found to be 6 to 8 s and 16 s, respectively.     

Hydrothermal fabrication of various morphological α-Fe2O3 nanoparticles modified by surfactants

Two kinds of various morphological α-Fe₂O₃ nanoparticles modified by anionic surfactant (sodium dodecylsulfonate, SDS) and cationic surfactant (hexadecyipyridinium chloride, HPC), respectively, have been synthesized via hydrothermal method, using simple inorganic salt (NH₄)₃Fe(C₂O₄)₃ and alkali NaOH as starting precursors. Meanwhile, α-Fe₂O₃ nanoparticles without surfactant are also fabricated under the same conditions for comparison. The resultant products were characterized by means of Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), transmission electron micrograph (TEM) combined with electron diffraction (ED) and magnetization measurements. It is interesting that the obtained α-Fe₂O₃ nanoparticles without surfactant are polyhedral with average particle size of 90 ± 35 nm; while the obtained α-Fe₂O₃ nanoparticles modified by SDS are ellipsoidal with mean particle size of major axis: ca. 420 nm; minor axis: ca. 205 nm and those modified by HPC are spherical with mean particle size of ca. 185 nm observed from TEM. In addition, magnetic hysteresis measurements reveal that the α-Fe₂O₃ nanoparticles modified by two surfactants show enhancement in coercivity (H_c) and the remanent magnetization (M_r) compared with those of the obtained α-Fe₂O₃ nanoparticles without surfactant at room temperature. The experimental results suggest that the surfactants not only significantly influence the size and shape of the particles, but also their magnetic properties.     

Synthesis and optical properties of hierarchical pure ZnO nanostructures

We report the catalyst-free synthesis of hierarchical pure ZnO nanostructures with 6-fold structural symmetry by two-step thermal evaporation process. At the first step, the hexagonal-shaped nanowires consisting of a great deal of Zn and little oxide were prepared via the layer-by-layer growth mechanism; and at the second step, hierarchical pure ZnO nanostructures were synthesized by evaporating the Zn source on the basis of the step-one made substrate. Scanning electron microscopy, transmission electron microscope images, and the corresponding selected area electron diffraction pattern have been utilized to reveal the screw dislocation growth mechanism, through which the single crystal ZnO nanorods are epitaxially grown from the side-wall of central axial nanowires. Raman and photoluminescence spectra further indicate that, for the hierarchical ZnO nanostructures, the ultraviolet peak is related to the free exciton recombination, while the oxygen vacancies and high surface-to-volume ratio are responsible for the strong green peak emission.     

Microwave synthesis of nanocrystalline Sb2S3 and its electrochemical properties

Nanocrystalline antimony trisulfide (Sb₂S₃) was successfully synthesized via microwave irradiation by the reaction of antimony trichloride (SbCl₃) and thiourea (CS(NH₂)₂) with PVP as the surfactant. The samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and high resolution TEM (HRTEM). XRD results show that the as-prepared sample is orthorhombic-phase Sb₂S₃. TEM image of the as-prepared Sb₂S₃ shows the rod-like structure. HRTEM image indicates that rodbundles of Sb₂S₃ consists of a number nanorods with the diameter ranging from 30 nm to 50 nm. Detailed HRTEM image demonstrates the preferential direction growth of the Sb₂S₃ nanorods. The electrochemical properties of Sb₂S₃ were primarily investigated by constant current charge/discharge cycling tests in lithium hexafluorophosphate (LiPF₆) solution. The possible electrochemical reaction mechanism was explained. The results indicate that the nanocrystalline Sb₂S₃ shows potential application in the field of the electrode materials.     

The catalytic behavior of zinc oxide prepared from various precursors and by different methods

Samples of zinc oxide were obtained by thermal decomposition of zinc salts (acetate and nitrate) and by precipitation (chloride and nitrate). The samples were characterized by S_BET, X-ray diffraction (XRD), temperature-programmed reduction (TPR) and scanning electron microscopy (SEM). XRD showed that ZnO crystals exhibited similar morphologies, while the crystal size and the particles morphology, availed by SEM, are dependent on the preparation method and the precursor salt utilized. The catalytic properties were evaluated to sec-butyl alcohol (SBA) reaction, using nitrogen, hydrogen and synthetic air as carrier gas. The catalytic properties of ZnO surface are strongly dependent on crystal size, atmosphere of reaction and zinc salts precursor. The activity to dehydrogenation of SBA in oxidant atmosphere is strongly sensitive to crystal size, while the selectivity to methyl ethyl ketone (MEK) is slightly sensitive. The activity to dehydrogenation and dehydration of SBA increases with change of atmosphere reaction from oxidant to reducing. High reaction temperatures and reducing environment for ZnO sample with small crystal size decrease significantly the selectivity to MEK. The ZnO crystal size has an important role to establish the properties of partial reduction of ZnO and catalytic properties.     

Synthesis by an ionic liquid-assisted method and optical properties of nanoflower Y2O3

Flower-like Y₂O₃ nano-/microstructured phosphors without metal activators have successfully been fabricated by an ionic liquid (IL)-assisted method involving temperature (600 °C) annealing. In this paper, the effect of IL concentration on the morphology of the product has been investigated. The IL plays a crucial role in the formation of various morphologies of Y₂O₃. The structural and morphological features of the obtained samples have been characterized by means of X-ray powder diffraction (XRD) analysis, photoluminescence spectra (PL), Fourier-transform infrared (FT-IR) spectra and X-ray photoelectron spectra (XPS). The photoluminescence spectra of the products exhibit an intense bluish-white emission (ranging from 405 to 430 nm and centered at 418 nm). The luminescent mechanisms have been ascribed to the carbon impurities in the Y₂O₃ host. The effect of the ILs cation and the counter anions on the Y₂O₃ morphology of these nanostructures was studied experimentally. It was observed that Y₂O₃ morphology and PL of these nanostructures were strongly influenced by the type of cation and anion. As the length of the subsidiary chain of cation section of IL (imidaziole ione) reduces, the thickness of the nano-sheets increases. It is expected that the present method may easily be extended to similar nano-/microstructures of other oxide materials. Such investigations are currently underway.     

Selective synthesis, characterization, and photoluminescence study of YPO4:Eu nanorods and nanoparticles

Two different morphological varieties of YPO₄:Eu³⁺ (nanorods and nanoparticles) have been synthesized by convenient template-assisted routes. A surfactant-mediated synthesis route generated the nanorods, while a complex based precursor solution method led to the formation of the nanoparticles. The nanorods have an average diameter of ∼33 nm and an average length of ∼290 nm, whereas the spherical nanoparticles show an average diameter of ∼34 nm. Upon photoluminescence study of the as-prepared samples, the chromaticity of the dopant ion was found to be sensitive to the host morphology as well as the preparative strategy adopted for sample fabrication.     

Application of nanostructured Ca doped CeO2 for ultraviolet filtration

Calcium doped CeO₂ nanoparticles with doping concentrations between 0 and 50 mol% were synthesized by a co-precipitation method for ultraviolet filtration application. Below 20 mol% doping concentration, the samples were single-phase. From 30 mol%, CaCO₃ appears as a secondary phase. The calculated CeO₂ mean crystallite size was 9.3 nm for the pure and 5.7 nm for the 50 mol% Ca-doped sample. Between 250 and 330 nm, the absorbance increased for the 10, 30, and 40 mol% Ca-doped samples compared to the pure one. The band-gap was found to be 3.20 eV for the undoped, and between 3.36 and 3.51 eV for the doped samples. The blue shifts are attributed to the quantum confinement effect. X-ray photoelectron spectroscopy showed that the Ce³⁺ atomic concentration in the pure sample was higher than that of the 20 mol% Ca-doped sample.     

Synthesis and surface plasmon resonance properties of carbon-coated Cu and Co nanoparticles

Carbon-coated Cu and Co nanoparticles were synthesized by the carbonization of PVA-metal hydroxide complexes. The possible reaction process and surface plasmon resonance (SPR) properties of the Cu and Co nanoparticles enwrapped in carbon layer were explored. The XRD results showed that no byproducts, such as oxides and carbides, were formed in the products, and the Cu and Co nanoparticles were effectively protected against oxidation by the carbon layer. The size ranges of the metal nanoparticles were 20-50 nm for Cu and 15-65 nm for Co, respectively. UV-vis absorption spectra showed that the SPR bands of the Cu and Co nanoparticles coated with carbon were red-shifted mainly due to the increase of the effective dielectric constant of the surrounding medium induced by the carbon layer.