聚丙烯/凹凸棒土复合材料的结晶行为

通过双螺杆挤出机熔融共混制备了聚丙烯(PP)/凹凸棒土(ATP)复合材料样品,分别采用偏光显微镜和差示扫描量热仪对其结晶行为进行了研究。研究表明,复合材料样品的偏光显微镜照片呈现球晶所特有的十字消光现象,球晶尺寸与纯PP球晶的尺寸相比有所减小。非等温结晶测试结果表明,复合材料样品的结晶温度随着ATP含量的增加向高温方向移动,而且半结晶期缩短,PP/ATP复合材料的总体结晶速率增加;ATP的加入改变了PP成核的机制,起到了异相成核的作用。随着降温速率的增大,PP及PP/ATP(95/5)复合材料的结晶起始温度和结晶峰值温度均向低温方向移动,半结晶期变短。     

聚对苯二甲酸丙二酯/蒙脱土复合材料的制备及性能研究

通过熔融共混法制备了聚对苯二甲酸丙二酯/蒙脱土(PTT/MMT)复合材料。采用DSC法对其非等温结晶性能进行了研究,结果表明MMT在复合材料中起到了异相成核作用,随着MMT含量的增加,PTT/MMT复合材料的结晶峰温θp向高温方向移动;采用偏光显微镜观察PTT及PTT/MMT复合材料在190℃等温结晶的情况下的球晶形态,PTT/MMT复合材料的球晶尺寸比PTT球晶尺寸大大减小;采用电子万能试验机、邵氏硬度计和D JF-20动态冲击分析仪对PTT及PTT/MMT复合材料的综合力学性能进行了测试,结果表明当MMT的质量分数为2%时的PTT/MMT复合材料的综合力学性能最佳。     

PTT/蒙脱土复合材料非等温结晶行为的研究

采用差示扫描量热仪对熔融共混制备的聚对苯二甲酸丙二醇酯(PTT)/蒙脱土(MMT)复合材料非等温结晶行为进行了测试分析。研究结果表明:在相同的降温速率时,随着MMT含量的增加,PTT/MMT复合材料的结晶峰温向高温方向移动,结晶峰变窄,半结晶期也缩短;随着降温速率的增大,PTT/MMT复合材料的结晶峰温向低温方向移动,半结晶期变短。采用Ozawa法处理了PTT/MMT复合材料的非等温结晶过程,结果表明:MMT的加入改变了PTT的成核机理,加快了PTT的结晶速率。     

PP/空心玻璃微珠复合材料非等温结晶研究

采用熔融共混挤出的方法,制备了聚丙烯(PP)/空心玻璃微珠(HGB)复合材料,用差示扫描量热法研究了PP和PP/HGB复合材料的非等温结晶过程,并通过Jeziorny和莫志深方程研究了非等温结晶动力学。结果表明,随降温速率的增大,PP和PP/HGB复合材料的结晶峰温和结晶度降低,结晶速率增大;HGB的加入降低了PP的结晶速率。     

PET/分子筛复合材料的非等温结晶性能

采用原位聚合法制备了PET／分子筛复合材料并研究了其非等温结晶性能。结果表明：分子筛的加入有明显的异相成核效应,加快了结晶速度,增加了结晶度,减小了晶粒粒径分布;PET及PET／分子筛体系的热结晶峰温随着降温速率的增加而移向低温,半结晶时间、结晶度随降温速率的增加而减小,晶粒粒径分布则增大;分子筛的加入降低了降温速率对PET半结晶时间的影响;随着分子筛用量的增加,半结晶时间t1／2、结晶热焓ΔH、结晶峰半峰宽ΔW都能达到一个较佳值。     

PET/PTT合金结晶形态的研究

采用XP-201热台偏光显微镜研究了对苯二甲酸乙二醇酯（PET）/对苯二甲酸丙二醇酯（PTT）合金等温结晶时的结晶形态及影响因素。研究结果表明：随着等温结晶温度的升高,PET/PTT(40/60)合金的结晶诱导期变长;在观察的时间范围内各样品的球晶尺寸随着时间的延长而增大;随着PTT含量的增加,样品球晶的线生长速率增大,球晶尺寸增大;对比不同温度下等温结晶的球晶形态,PET/PTT(100/0)样品在190℃结晶时球晶尺寸最大, PET/PTT(40/60)样品和PET/PTT(100/0)样品在180℃结晶时球晶尺寸最大; PET/PTT(0/100)样品等温结晶时呈现出了复杂的条带球晶。     

磷石膏增强聚丙烯复合材料的非等温结晶动力学

分别采用Jeziorny法和莫志深法研究了采用熔融挤出法制备的工业废渣磷石膏(PhG)增强聚丙烯(PP)复合材料的非等温结晶动力学。结果表明：两种方法研究结果基本一致。随着降温速率的增加,纯PP和PP/PhG复合材料的结晶温度均逐渐降低,结晶峰峰宽逐渐增大;PhG的加入降低了PP晶体中晶粒尺寸,提高了PP的结晶速率;PhG在PP基体中主要起均相成核作用,晶体的生长方式为三维球晶生长;采用Kissinger模型计算的纯PP的非等温结晶活化能为-231 kJ/mol,PP/PhG的非等温结晶活化能为-275 kJ/mol。     

PP/PP-g-MAH/HGB复合材料非等温结晶行为研究

采用熔融法制备了聚丙烯/马来酸酐接枝聚丙烯/空心玻璃微珠（PP/PP-g-MAH/HGB）复合材料,采用差示扫描量热仪研究了PP、PP/HGB、PP/PP-g-MAH/HGB复合材料的非等温结晶过程,并通过Jeziorny法和Mo法研究了3种材料的非等温结晶动力学。结果表明,随着降温速率的增大,3种材料的结晶峰温、结晶起始温度和结晶度均减小,结晶速率增大;HGB抑制了PP的结晶行为,降低了结晶速率;PP-g-MAH对PP结晶速率的影响较小,HGB和PP-g-MAH都会改变PP的结晶成核和生长机理。     

聚丙烯/海泡石复合材料的等温结晶行为

采用熔融共混的方法制备聚丙烯（PP）/海泡石复合材料,通过示差扫描量热仪和偏光显微镜研究有机化改性海泡石填充PP复合材料在不同温度下的等温结晶行为,考察海泡石对PP结晶行为的影响,采用Avrami方程处理等温结晶过程,并计算结晶动力学参数。结果表明,海泡石的加入使复合材料的结晶时间缩短,结晶度增大;随着结晶温度的升高,各体系的结晶速率下降,结晶速率常数n、K降低,并且随着结晶温度（Tc）的升高,半结晶时间（t1/2）增大;在同一结晶温度（Tc）下,海泡石的加入提高了基体的结晶速率,加快了PP的异相成核过程,使得PP球晶尺寸减小。     

PTT/PE共混体系结晶动力学及结晶形态研究

采用差示扫描量热法(DSC)研究了聚对苯二甲酸丙二醇酯/聚乙烯(PTT/PE)共混体系的非等温结晶动力学,通过热台偏光显微镜(POM)对共混物在等温条件下的结晶形态进行了研究。结果发现:PTT/PE共混体系各样品的结晶峰温度随着冷却速率的提高而下降,而半结晶时间t1/2随着冷却速率的提高而提高;结晶动力学常数Zc随着冷却速率的提高而下降,表明共混体系的结晶速率随着冷却速率的提高而降低;在POM观察的时间范围内各样品的球晶尺寸随着时间的延长而增大,PTT/PE(30/70)共混体系在190℃结晶时,球晶尺寸较大,即球晶生长较快。     

Poly(propylene)–poly(propylene)‐grafted maleic anhydride–organic montmorillonite (PP–PP‐g‐MAH–Org‐MMT) nanocomposites. II. Nonisothermal crystallization kinetics

The nonisothermal crystallization kinetics of poly(propylene) (PP), PP–organic‐montmorillonite (Org‐MMT) composite, and PP–PP‐grafted maleic anhydride (PP‐g‐MAH)–Org‐MMT nanocomposites were investigated by differential scanning calorimetry (DSC) at various cooling rates. Avrami analysis modified by Jeziorny and a method developed by Mo well‐described the nonisothermal crystallization process of these samples. The difference in the exponent n between PP and composite (either PP–Org‐MMT or PP–PP‐g‐MAH–Org‐MMT) indicated that nonisothermal kinetic crystallization corresponded to tridimensional growth with heterogeneous nucleation. The values of half‐time, Z_c; and F(T) showed that the crystallization rate increased with the increasing of cooling rates for PP and composites, but the crystallization rate of composites was faster than that of PP at a given cooling rate. The method developed by Ozawa can also be applied to describe the nonisothermal crystallization process of PP, but did not describe that of composites. Moreover, the method proposed by Kissinger was used to evaluate the activation energy of the mentioned samples. The results showed that the activation energy of PP–Org‐MMT was much greater than that of PP, but the activation energy of PP–PP‐g‐MAH–Org‐MMT was close to that of pure PP. Overall, the results indicate that the addition of Org‐MMT and PP‐g‐MAH may accelerate the overall nonisothermal crystallization process of PP. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 3093–3099, 2003     

Study on the Crystallization Properties of Polypropylene/Montmorillonite Composites

The crystalline size of polypropylene (PP) filled with montmorillonite (MMT) was studied by X-ray diffraction (XRD). The isothermal crystallization behavior of polypropylene was studied by means of differential scanning calorimetry (DSC). The Avrami equation was used to describe the isothermal crystalline kinetics of PP/MMT composites. The result showed that the addition of MMT decreased the crystalline size L _hkl of the polymer. MMT was used as nucleating agent during isothermal crystallization process of polypropylene. The addition of montmorillonite decreased the crystallization time of the polypropylene and the melt point was raised. The value of Avrami exponent n was related with the crystallization temperature. The value of Avrami pre-index factor k of PP/MMT composite was decreased with increasing crystallization temperature. The value of half crystallization time t _1/2 of PP/MMT composite was less than that of PP at a given crystallization temperature, signifying that montmorillonite acted as nucleating agent, accelerated the overall crystallization process.     

聚丙烯/聚苯乙烯/膨润土共混体系的结晶性能和热性能研究

通过偏光显微镜(PLM)和光学解偏振仪对聚丙烯/聚苯乙烯/膨润土三元共混体系的结晶形态和等温结晶速率进行了研究。结果表明:共混体系所形成的球晶比纯聚丙烯(PP)所形成的球晶尺寸小,聚苯乙烯(PS)/膨润土(Garamite)复合粒子的加入导致PP的结晶成核和生长发生了改变,加快了PP的结晶速率。同时采用差示扫描量热仪(DSC)对该三元共混体系的热性能进行了研究,结果表明,随着膨润土含量的增加,共混体系熔融温度变高,结晶温度变高,结晶度下降。     

Study on the crystallization kinetics of PP/GF composites

The crystallization kinetics and morphology of glass fiber-reinforced polypropylene (PP/GF) were investigated in this work. Both isothermal and nonisothermal crystallization behaviors of 90PP/10GF, 80PP/20GF, and 70PP/30GF were examined with a DSC instrument. It was found that the addition of glass fiber would increase the crystallization rate of PP and increase the content of β spherulite, which was most likely formed at temperatures between 390 and 400 K. The morphology of spherulites of PP/GF composites were examined with SEM and a polarized microscope. All experimental observations conformed rather well with the theoretical approach, a dynamic crystallization model, proposed in our previous work. The size of α spherulites of PP would decrease at lower crystallization temperature, or at higher cooling rate, or by adding glass fiber in it.     

PET/PTT合金非等温结晶行为的研究

采用差示扫描量热仪对熔融共混制备的聚对苯二甲酸乙二醇酯（PET）/聚对苯二甲酸丙二醇酯（PTT）合金的非等温结晶行为进行研究。结果表明,在相同的降温速率时, 随着PTT含量的增加,PET/PTT合金结晶峰温度向低温方向移动,而且当合金中PET与PTT含量接近时,合金样品出现了双重结晶峰;在降温结晶的过程中,随着降温速率的增大,各合金样品结晶峰温度均降低,其结晶峰均宽化;采用Jeziorny法对上述非等温结晶过程进行了分析,分析结果表明,随着降温速率的增大,各合金样品非等温结晶速率常数增加,其Avrami指数在1~5之间,并且逐渐减小。     

PP/纳米TiO2复合材料的晶体形貌和非等温结晶行为

用熔融共混法制备了聚丙烯（PP）/纳米TiO2复合材料,用透射电子显微镜、偏光显微镜、差示扫描量热仪和广角X射线衍射仪对其纳米粒子分散性、晶体形貌和非等温结晶行为进行了研究。结果表明,纳米TiO2以纳米级尺寸均匀分散于PP基体中;130 ℃冷却和室温冷却时,PP/纳米TiO2复合材料的晶粒比纯PP的细,并且随着纳米TiO2含量的增加,PP/纳米TiO2复合材料的晶粒尺寸先减小后增大,纳米TiO2含量为2 %（质量分数,下同）时晶粒最细;纳米TiO2对PP结晶具有加速作用;复合材料的结晶活化能高于纯PP的,并且纳米TiO2含量多且均匀时复合材料结晶活化能高;纳米TiO2含量较少时可诱导较多的β晶生成,当纳米TiO2含量为1 %时,复合材料中β晶含量达到25.2 %。     

Crystallization behaviors of polypropylene/montmorillonite nanocomposites

The isothermal crystallization kinetics of polypropylene/montmorillonite (PP/MMT) nanocomposites synthesized via intercalation polymerization were investigated by using differential scanning calorimeter and polarizing optical microscope (POM). The crystallinity of the nanocomposites decreased with the increase of the montmorillonite content, indicating that the MMT layers dispersed in the PP matrices confined the PP chains and hindered the crystallization of the PP chains. The POM photographs showed that the spherulites of the PP/MMT nanocomposites were greatly decreased in size as MMT was introduced. On the other hand, the crystallization rate increased dramatically with the increasing of MMT content. The interfacial free‐energy per unit area perpendicular to PP chains in PP/MMT nanocomposites decreased with increasing MMT content, suggesting that the MMT layers acted as heterogeneous nuclei in the nucleation of crystallization. The nucleus density increased with the increasing of MMT content, leading to a positive effect on the crystallization. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1978–1985, 2002