嘉峪关长城望宇炉业有限责任公司

<正>嘉峪关市长城望宇炉业有限责任公司自主开发、研制出适用于焦炉热修补的陶瓷焊补和半干法喷补技术,其中陶瓷焊补机分别获得5项国家实用新型专利:焦炉陶瓷焊补机(专利号:03 2 57272.7)、改进的焦炉陶瓷焊补机(专利号:201120263640.3)、气动焦炉陶瓷焊补机(专利号:201120393763.9)、改进气动陶瓷焊补机(专利号:201220459485.7)和焦炉陶瓷喷焊机(专利号:201420139684.9)。     

焦炉耐火砌体的检修方法

陈述了克里沃罗格焦化厂焦炉的生产状况，最高寿命达20年以上。认为焦炉最佳生产条件为稳定配煤质量、规定结焦时间及控制炉子操作，并为焦炉设计了包括高温计、存储装置及计算机在内的监控系统。常用的焦炉检修方法为火焰喷补、陶瓷焊补及放热性料喷补。文中介绍了陶瓷焊补机的性能、焊补料及放热性料的化学成分，示出了对焦炉燃烧室进行局部重砌时的炉室布置图及温度制度，以及缩短停炉时间的措施。     

莫来石陶瓷中的位错与断裂

有透射电镜和扫描电镜研究了莫来石陶瓷的亚结构特征和断裂过程。发现裂纹尖端成分布着位错列。认为这种特写位错的交互作用引起了莫来石陶瓷的解理和早期断裂，并使莫来石陶瓷在常温显示低的强度。实验证实，掺加第二相显微颗粒，能有效地钉扎位错，也提高了莫来石陶瓷的常温强度。     

莫来石/刚玉复相陶瓷热断裂特性研究

通过调整复相陶瓷中颗粒相的组成与级配,利用引入的热膨胀失配机制,控制莫来石/刚玉复相陶瓷显微结构,改善高温复相陶瓷热稳定性,着重研究了莫来石/刚玉复相陶瓷的热断裂特性.研究表明,全部采用莫来石颗粒相时,由于柱状莫来石颗粒极易发生热冲击穿晶断裂,且热膨胀失配导致的微裂纹较长,密度较小,故复相陶瓷热稳定性较差;全部采用刚玉颗粒相时,虽然基质相裂纹扩展至刚玉颗粒表面时穿晶断裂与沿晶的裂纹扩展同时发生,有利于改善复相陶瓷热稳定性,但由于热膨胀失配过度,未经热冲击时已产生宏观裂纹,故热稳定性最差.而采用莫来石/刚玉复合颗粒相,相比例为75/25制备的复相陶瓷试样,热膨胀失配形成的微裂纹较短,密度较大,其热稳定性最优.     

氧化铝/莫来石复合陶瓷断裂行为研究

用X射线衍射方法测定了氧化铝/莫来石复合陶瓷的残余应力,并通过计算加以验证。在莫来石含量比较小的情况下,氧化铝/莫来石复合陶瓷基体拉应力与莫来石体积含量成线性关系。通过模型分析了氧化铝基体和莫来石颗粒的应力状态及其对裂纹扩展的影响。由莫来石颗粒引入的基体拉应力使裂纹倾向于向晶内扩展。观察了氧化铝/莫来石复合陶瓷断裂方式的转变,计算了穿晶断裂比率与基体应力的关系,进而建立了莫来石含量、基体应力、穿晶断裂比率三者的对应关系。这为复合陶瓷材料的制备和性能分析提供了可靠基础。     

莫来石纤维多孔陶瓷粘结用的莫来石纳米晶的研制

粘结剂在纤维多孔陶瓷制备过程中起着关键性作用,对用作莫来石纤维多孔陶瓷粘结用的莫来石微晶制备过程和结构进行了分析研究。分析结果表明：所研制粘结剂胶体颗粒的ζ-电位为35．75mV;粘结剂在烧结过程中经历了如下变化：无定形物质→微量γ—Al2O3（970℃）→铝硅尖晶石（1030℃）→莫来石与铝硅尖晶石（1150℃）→莫来石纳米晶（1250℃）。烧结后的莫来石晶粒平均尺寸为6463nm;对晶胞参数的测定表明其与莫来石纤维具有良好的晶体结构上的匹配性。     

莫来石及多孔莫来石的研究和应用

高温性能稳定,抗热震性能好的莫来石是一种重要的工程陶瓷材料。概述了莫来石的结构、性能,以及在工业上的应用,并对多孔莫来石陶瓷的研究进展和应用进行了介绍。针对莫来石室温力学性能较差的缺陷,讨论了氧化锆和颗粒增韧莫来石的方法。最后,对多孔ZTM陶瓷发展前景进行了展望。     

Al2O3对ZTM陶瓷结构与性能的影响

本文研究了氧化铝对ZTM陶瓷结构和性能的影响.发现在烧结过程中,氧化铝可固溶于莫来石颗粒形成富铝型柱状莫来石,产生的体积膨胀增强了基质对氧化锆颗粒的约束,使材料中的四方氧化锆相对含量增加,其强韧化效果进一步发挥,明显改善了材料的力学性能.     

用莫来石－刚玉陶瓷作为石油裂解触媒载体

用莫来石－刚玉陶瓷作为石油裂解的触媒载体能提高乙烯产率。介绍了莫来石－刚玉陶瓷载体和触媒的制备工艺，讨论了所含颗粒成分及其含量对触媒载体性能的影响。     

Al2O3在莫来石中固溶对ZTM/Al2O3陶瓷结构与性能的影响

研究了加入氧化铝对ZTM陶瓷结构和性能的影响.发现在烧结过程,氧化铝可固溶于莫来石颗粒形成富铝型柱状莫来石,并因其产生的体积膨胀增强了基质对氧化锆颗粒的约束,使材料中的四方氧化锆相对含量增加,其强韧化效果进一步发挥,明显改善了材料的力学性能.     

Insect antifeedant properties of anthranoids from the genusVismia

Vismiones and ferruginins, representatives of a new class of lypophilic anthranoids from the genusVismia were found to inhibit feeding in larvae of species ofSpodoptera, Heliothis, and inLocusta migratoria.     

Direct observation of freeze-thaw instability of latex coatings via high pressure freezing and cryogenic SEM

Despite its industrial importance, the subject of freeze-thaw (F/T) stability of latex coatings has not been studied extensively. There is also a lack of fundamental understanding about the process and the mechanisms through which a coating becomes destabilized. High pressure (2100 bar) freezing fixes the state of water-suspended particles of polymer binder and inorganic pigments without the growth of ice crystals during freezing that produce artifacts in direct imaging scanning electron microscopy (SEM) of fracture surfaces of frozen coatings. We show that by incorporating copolymerizable functional monomers, it is possible to achieve F/T stability in polymer latexes and in low-VOC paints, as judged by the microstructures revealed by the cryogenic SEM technique. Particle coalescence as well as pigment segregation in F/T unstable systems are visualized. In order to achieve F/T stability in paints, latex particles must not flocculate and should provide protection to inorganic pigment and extender particles. Because of the unique capabilities of the cryogenic SEM, we are able to separate the effects of freezing and thawing, and study the influence of the rate of freezing and thawing on F/T stability. Destabilization can be caused by either freezing or thawing. A slow freezing process is more detrimental to F/T stability than a fast freezing process; the latter actually preserves suspension stability during freezing. Presented at the 82nd Annual Meeting of the Federation of Societies for Coatings Technology, October 27–29, 2004 in Chicago, IL. Tied for first place in The John A. Gordon Best Paper Competition.     

Ethanol and (−)-α-Pinene: Attractant Kairomones for Bark and Ambrosia Beetles in the Southeastern US

In 2002–2004, we examined the flight responses of 49 species of native and exotic bark and ambrosia beetles (Coleoptera: Scolytidae and Platypodidae) to traps baited with ethanol and/or (−)-α-pinene in the southeastern US. Eight field trials were conducted in mature pine stands in Alabama, Florida, Georgia, North Carolina, and South Carolina. Funnel traps baited with ethanol lures (release rate, about 0.6 g/day at 25–28°C) were attractive to ten species of ambrosia beetles (Ambrosiodmus tachygraphus, Anisandrus sayi, Dryoxylon onoharaensum, Monarthrum mali, Xyleborinus saxesenii, Xyleborus affinis, Xyleborus ferrugineus, Xylosandrus compactus, Xylosandrus crassiusculus, and Xylosandrus germanus) and two species of bark beetles (Cryptocarenus heveae and Hypothenemus sp.). Traps baited with (−)-α-pinene lures (release rate, 2–6 g/day at 25–28°C) were attractive to five bark beetle species (Dendroctonus terebrans, Hylastes porculus, Hylastes salebrosus, Hylastes tenuis, and Ips grandicollis) and one platypodid ambrosia beetle species (Myoplatypus flavicornis). Ethanol enhanced responses of some species (Xyleborus pubescens, H. porculus, H. salebrosus, H. tenuis, and Pityophthorus cariniceps) to traps baited with (−)-α-pinene in some locations. (−)-α-Pinene interrupted the response of some ambrosia beetle species to traps baited with ethanol, but only the response of D. onoharaensum was interrupted consistently at most locations. Of 23 species of ambrosia beetles captured in our field trials, nine were exotic and accounted for 70–97% of total catches of ambrosia beetles. Our results provide support for the continued use of separate traps baited with ethanol alone and ethanol with (−)-α-pinene to detect and monitor common bark and ambrosia beetles from the southeastern region of the US.     

Methyl 2,4,6-decatrienoates Attract Stink Bugs and Tachinid Parasitoids

Halyomorpha halys (Stål) (Pentatomidae), called the brown marmorated stink bug (BMSB), is a newly invasive species in the eastern USA that is rapidly spreading from the original point of establishment in Allentown, PA. In its native range, the BMSB is reportedly attracted to methyl (E,E,Z)-2,4,6-decatrienoate, the male-produced pheromone of another pentatomid common in eastern Asia, Plautia stali Scott. In North America, Thyanta spp. are the only pentatomids known to produce methyl 2,4,6-decatrienoate [the (E,Z,Z)-isomer] as part of their pheromones. Methyl 2,4,6-decatrienoates were field-tested in Maryland to monitor the spread of the BMSB and to explore the possibility that Thyanta spp. are an alternate host for parasitic tachinid flies that use stink bug pheromones as host-finding kairomones. Here we report the first captures of adult and nymph BMSBs in traps baited with methyl (E,E,Z)-2,4,6-decatrienoate in central Maryland and present data verifying that the tachinid, Euclytia flava (Townsend), exploits methyl (E,Z,Z)-2,4,6-decatrienoate as a kairomone. We also report the unexpected finding that various isomers of methyl 2,4,6-decatrienoate attract Acrosternum hilare (Say), although this bug apparently does not produce methyl decatrienoates. Other stink bugs and tachinids native to North America were also attracted to methyl 2,4,6-decatrienoates. These data indicate there are Heteroptera in North America in addition to Thyanta spp. that probably use methyl 2,4,6-decatrienoates as pheromones. The evidence that some pentatomids exploit the pheromones of other true bugs as kairomones to find food or to congregate as a passive defense against tachinid parasitism is discussed.     

2007～2008年世界塑料工业进展

收集了2007年7月～2008年6月世界塑料工业的相关资料,介绍了2007～2008年国外塑料工业的发展情况,提供了世界塑料产量、消费量及全球各类树脂的需求量及产能情况.按通用热塑性树脂(聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂)、工程塑料(尼龙、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚)、特种工程塑料(聚苯·硫醚、液晶聚合物、聚醚醚酮)、通用热固性树脂(酚醛、聚氨酯、不饱和聚酯树脂、环氧树脂)不同品种的顺序,对树脂的产量、消费量、供需状况及合成工艺、产品应用开发、树脂品种的延伸及应用的进一步扩展等技术作了详细介绍.     

2005～2006年国外塑料工业进展

收集了2005年7月～2006年6月国外塑料工业的相关资料,介绍了2005—2006年国外塑料工业的发展情况。提供了世界塑料产量、消费量及全球各类树脂生产量以及各国塑料制品的进出口情况。作为对比,介绍了中国塑料的生产情况。按通用热塑性树脂（聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂）、工程塑料（聚酰胺、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚）、通用热固性树脂（酚醛、聚氨酯、不饱和树脂、环氧树脂）、特种工程塑料（聚苯硫醚、液晶聚合物、聚醚醚酮）的品种顺序,对树脂的产量、消费量、供需状况及合成工艺、产品开发、树脂品种的延伸及应用的扩展作了详细的介绍。