Chemical modification of styrene–butadiene–styrene co-polymer by grafting of N-carbamyl maleamic acid

A styrene–butadiene–styrene (SBS) block co-polymer was functionalized using different amounts of N-carbamyl maleamic acid (NCMA) and benzoyl peroxide as initiator. NCMA, which is a bifunctional monomer, was synthesized in our laboratories. The concentration of NCMA used in the functionalization of SBS ranged from 0.5 to 3% (w/w) based on the co-polymer mass. Benzoyloxy radicals generated from the thermal decomposition of benzoyl peroxide initiated the grafting reaction. The concentration of the initiator was kept constant at 0.076% (w/w). FT-IR spectroscopy was used to determine the amount of NCMA effectively grafted onto the SBS. The maximum amount of monomer grafted was about 0.3% (w/w) when the SBS was modified with 1% (w/w) NCMA. The effect of grafting on the surface properties and the adhesion to polyurethane adhesive of the modified SBS were evaluated. Contact angle values were obtained using liquid droplets. When the concentration of the NCMA used in the grafting reaction was 1% (w/w), the contact angles with water on original and modified SBS were 95° and 77°, respectively. Adhesion properties were evaluated by standard peel tests employing a commercial polyurethane adhesive. The modified SBS having the largest amount of NCMA displayed a T-peel strength value 5-times higher than the corresponding value measured with the original SBS.     

A conductive foam: Based on novel poly(styrene‐b‐butadiene‐co‐styrene‐b‐styrene) tri‐block copolymer filled by carbon black

In this article, a conductive foam based on a novel styrene‐based thermoplastic elastomer called poly(styrene‐b‐butadiene‐co‐styrene‐b‐styrene) tri‐block copolymer S(BS)S was prepared and introduced. S(BS)S was particularly designed for chemical foaming with uniform fine cells, which overcame the shortcomings of traditional poly(styrene‐b‐butadiene‐b‐styrene) tri‐block copolymer (SBS). The preparation of conductive foams filled by the carbon black was studied. After the detail investigation of cross‐linking and foaming behaviors using moving die rheometer, the optimal foaming temperature was determined at 180°C with a complex accelerator for foaming agent. Scanning electron microscopy (SEM) images shown that the cell bubbles of conductive foam were around 30–50 µm. The conductivity of foams was tested using a megger and a semiconductor performance tester. SEM images also indicated that the conductivity of foams was mainly affected by the distribution of carbon black in the cell walls. The formation of the network of the carbon black aggregates had a contribution to perfect conductive paths. It also found that the conductivity of foams declined obviously with the foaming agent content increasing. The more foaming agent led to a sharp increasing of the number of cells (from 2.93 × 10⁶ to 6.20 × 10⁷ cells/cm³) and a rapid thinning of the cell walls (from 45.3 to 1.4 µm), resulting in an effective conductive path of the carbon black no forming. The conductive soft foams with the density of 0.48–0.09 g/cm³ and the volume resistivity of 3.1 × 10³?2.5 × 10⁵ Ω cm can be easily prepared in this study. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41644.     

Benzoyl peroxide–p‐acetylbenzylidenetriphenyl arsoniumylide initiated copolymerization of citronellol and styrene

Alternating copolymers, containing styrene and citronellol sequences, have been synthesized by radical polymerization using benzoylperoxide (BPO)–p‐acetylbenzylidenetriphenyl arsoniumylide (pABTAY) as initiator, in xylene at 80 ± 1 °C for 3 h under inert atmosphere. The kinetic expression is R_p ∝ [BPO]^0.88 [citronellol]^0.68 [styrene]^0.56 with BPO and R_p ∝ [pABTAY]^0.27 [citronellol]^0.76 [styrene]^0.63 with pABTAY, ie the system follows non‐ideal kinetics in both cases, because of primary radical termination and degradative chain transfer reactions. The activation energy with BPO and pABTAY is 94 kJ mol^?1 and 134 kJ mol^?1, respectively. Different spectral techniques, such as IR, FTIR, ¹H NMR and ¹³C NMR, have been used to characterize the copolymer, demonstrating the presence of alcoholic and phenyl groups of citronellol and styrene. The alternating nature of the copolymer is shown by the product of reactivity ratios r₁ (Sty) = 0.81 and r₂ (Citro) = 0.015 using BPO and r₁ (Sty) = 0.37 and r₂ (Citro) = 0.01 using (pABTAY), which are calculated by the Finemann–Ross method. A mechanism of copolymerization is proposed. © 2001 Society of Chemical Industry     

Copolymerization of butadiene with styrene using a rare‐earth metal compound – dialkylmagnesium – halohydrocarbon catalytic system

Copolymerizations of butadiene (Bd) with styrene (St) were carried out with catalytic systems composed of a rare‐earth compound, Mg(n‐Bu)₂ (di‐n‐butyl magnesium) and halohydrocarbon. Of all the rare earth catalysts examined, Nd(P₅₀₇)₃–Mg(n‐Bu)₂–CHCl₃ showed a high activity in the copolymerization under certain conditions: [Bd] = [St] = 1.8 mol l^?1, [Nd] = 6.0 × 10^?3 mol l^?1, Mg/Nd = 10, Cl/Nd = 10 (molar ratio), ageing for 2 h, copolymerization at 50 °C for 6–20 h. The copolymer of butadiene and styrene obtained has a relatively high styrene content (10–30 mol%), cis‐1,4 content in butadiene unit (85–90%), and molecular weight ([η] = 0.8–1 dL g^?1). Monomer reactivity ratios were estimated to be r_Bd = 36 and r_St = 0.36 in the copolymerization. © 2002 Society of Chemical Industry     

Preparation of SBS/poly(styrene–methyl methacrylate) thermoplastic interpenetrating polymer network

SBS as polymer I, poly(styrene–methyl methacrylate) polymerized by atom transfer radical polymerization as polymer II, and a thermoplastic interpenetrating polymer network of SBS/poly(styrene–methyl methacrylate) were prepared by the sequential method. The effects of the polymerization temperature, the composition of the catalyst, the ratio of the monomers studied, and the kinetics at 90°C were also investigated. It was shown that when polymerization was initiated by a BPO/CuCl/bpy (BPO:CuCl:bpy = 1:1:3) system at 90°C, the mass averaged molecular weight of the poly(styrene–methyl methacrylate) increased with monomer conversion, and the polydispersities were kept very low. Fourier transform infrared spectroscopy and gel permeation chromatogram showed that poly(styrene–methyl methacrylate) with low polydispersities had been synthesized. Thus, a thermoplastic interpenetrating polymer network comprised of both narrow molecular‐weight‐distribution components was successfully prepared. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2007–2011, 2003     

Effects of molecular weight and arm number on properties of star‐shape styrene–butadiene–styrene triblock copolymer

A star‐shape styrene–butadiene–styrene triblock copolymer SBS (802) was synthesized and fractionated into four fractions coded as 802‐F1 (four arms), 802‐F2 (two arms), 802‐F3 (one arm), and 802‐F4 by repeating fractional precipitation. Their weight‐average molecular weight (M_w) was measured by size‐exclusion chromatography combined with laser light scattering to be 16.0 × 10⁴, 8.2 × 10⁴, 4.3 × 10⁴, and 1.19 × 10⁴, respectively. The samples were, respectively, compression‐molded and solution‐cast to obtain the sheets coded as 802C, 802‐F1C, 802‐F2C, and 802S, 802‐F1S, 802‐F2S. The structures and mechanical properties of the sheets were characterized by ¹H‐NMR, scanning electron microscope, wide‐angle X‐ray diffractometer, tensile testing, and dynamic mechanical thermal analysis. The results indicated that the compression‐molded 802‐F1C exhibited the higher tensile strength (σ_b, 28.4 MPa) and elongation at break (ε_b, 1610%), and its optical transmittance is much higher than those of 802C and 802‐F2C. This work revealed that the star‐shape SBS with four arms could be helpful in the enhancement of the properties as a result of good miscibility of the compression‐molded SBS sheets. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 832–840, 2005     

A pH‐sensitive porous chitosan membrane prepared via surface grafting copolymerization in supercritical carbon dioxide

We report the successful grafting copolymerization of acrylic acid (AA) on a crosslinked porous chitosan membrane in supercritical carbon dioxide at pressures ranging from 13 to 25 MPa with the use of benzyl peroxide (BPO) as the reduction–oxidation free radical initiator. The effects of reaction pressure, initiator concentration, monomer concentration, reaction temperature and reaction time on grafting yield (GY) were investigated. GY initially increases and then decreases with increasing polymerization temperature and AA and BPO concentrations. The optimum grafting conditions to obtain maximum GY are as follows: 8 h reaction time, 80 °C reaction temperature, 3.05 × 10^?2 g mL^?1 AA concentration, 3 × 10^?3 g mL^?1 BPO concentration and 16 MPa reaction pressure. The water flux of the grafted chitosan membranes decreases with pH from 2 to 7, even at considerably low GY (0.95 wt%). A novel and green modification method has been developed for the preparation of biopolymer‐based membranes. © 2014 Society of Chemical Industry     

Preparation and properties of bitumen modified with the maleic anhydride grafted styrene‐butadiene‐styrene triblock copolymer

A procedure to improve the properties of styrene‐butadiene‐styrene (SBS) copolymer modified bitumen by grafting of maleic anhydride (MAH) onto SBS in the presence of benzoyl peroxide (BPO) as initiator was proposed. The effects of the grafting degree (GD) on the properties of modified bitumen were investigated. FTIR spectroscopy was employed to verify the grafting of MAH onto SBS. The GD of MAH onto SBS was determined by a back titration procedure. To assess the effects of the GD of grafted SBS on properties of modified bitumen, the softening point, penetration, ductility, elastic recovery, penetration index, viscosity, storage stability, and dynamic shear properties were tested. Experimental results indicated that the SBS grafted with maleic anhydride (SBS‐g‐MAH) copolymer was successfully synthesized by solvothermal method, and different GD of the SBS‐g‐MAH was obtained by control the MAH concentration. The GD of the MAH onto SBS has great effect on the rheological properties of the modified bitumen, and the high temperature performance and storage stability of modified bitumen were improved with the GD of the MAH onto SBS increasing. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Synthesis and characterization of p‐perfluoro{1‐[2‐(2‐fluorosulfonyl‐ethoxy)propoxy]}ethylated poly(α‐methyl styrene)

p‐Perfluoro{1‐[2‐(2‐fluorosulfonyl‐ethoxy)propoxy]}ethylated poly(α‐ methyl styrene) 3 was synthesized via electron transfer of perfluoro‐di{2‐[2‐(2‐fluorosulfonyl‐ethoxy)propoxy]}propionyl peroxide 2 and poly(α‐methyl styrene) 1 at different reactant molar ratios (2 : 1). The modified polymer 3 was characterized by various techniques. The ring p‐substitution was proved by FTIR and ¹⁹FNMR. The desulfonation appeared at above 124°C was found by TGA. The molecular weight determined by GPC increased with the increase of reactant molar ratio, and the polydispersity values indicated there was no degradation of the parent polymer chain in the reaction. Followed by hydrolysis and acidification, the modified polymer 3 could be further quantitatively converted into its sulfonic form 4. Ion exchange capacity of novel polyelectrolyte 4 can be controlled by changing reactant molar ratio (2 : 1). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3615–3618, 2006     

Synthesis and properties of a novel (main‐chain)– (side‐chain) polymeric peroxide

A novel (main‐chain)‐(side‐chain) vinyl polyperoxide, poly(dipentene peroxide) (PDP), an alternating copolymer of dipentene (DP) and oxygen, has been synthesized by thermal oxidative polymerization of DP. The PDP was characterized by ¹H NMR, ¹³C NMR, FTIR, DSC, TGA, and EI‐MS studies. The overall activation energies of the degradation from Kissinger's method were 28 and 33 kcal/mol, respectively, for the endocyclic and acyclic peroxide units. The side‐chain peroxy groups were found to be thermally more stable than the main chain. Above 45°C the rate of polymerization increases sharply at a particular instant showing an “autoacceleration” with the formation of knee point. The kinetics of autoacceleration has been studied at various temperatures (45–70°C) and pressures (50–250 psi). © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1549–1555, 2001     

m‐Chloroaniline emulsion polymerization,macromolecular chain structure and electrochemical properties

Poly(m‐chloroaniline) (PmClAn) was synthesized by emulsion polymerization. The influences of reaction temperature and initiator concentration on polymerizations were studied. It was found that PmClAn with number‐average molecular weight of 1.85 × 10³ g mol^?1 was obtained by the following conditions: 80 °C, [monomer] = 0.187 × 10^?3 mol l^?1, [sodium lauryl sulfate] = 4.8 × 10^?2 mol l^?1, [potassium peroxydisulfate] = 5.6 × 10^?2 mol l^?1, reaction period = 2.0 h. ¹H NMR, FTIR, and transmission and scanning microscopy were used for structural characterization of PmClAn. It was shown that the ratio of benzoid to quinoid units in the macromolecular chain was respectively 3:2, and that PmClAn has a typical crystalline monoclinic form. A PmClAn molecular chain configuration was also proposed on the basis of crystallographic data. Cyclic voltammetry experiments revealed the PmClAn membrane electrode electroactivity. This electroactivity increased when the polymer was proton‐doped. When Pt particles were electrodeposited onto the polymer membrane electrode, they presented a preferred orientation. Isopropanol oxidation intensities with platinized PmClAn modified electrodes were larger than with a platinized Pt electrode. We also found that oxidation occurred mainly on the Pt particles deposited on the polymer, and that the anodic peak potential changed with polymer and its doping level. These results indicated that the Pt particles interacted with the polymer and that catalytic properties could be observed. © 2002 Society of Chemical Industry     

Synthesis of styrene–ethylene–butylene–styrene triblock copolymer‐g‐polylactic acid copolymer and its potential application as a toughener for polylactic acid

The copolymer of styrene–ethylene–butylene–styrene triblock copolymer‐g‐polylactic acid (SEBS‐g‐PLA) was successfully prepared using a novel solvothermal synthetic method, in which the graft copolymerization of PLA and SEBS was simply performed in cholorform solution at 100–150°C with benzoyl peroxide (BPO) as initiator. The effect of various factors including the reaction temperature and time and the content of BPO and PLA on the graft copolymerization was investigated in detail. It is found that the optimal reaction condition for the grafted copolymers SEBS‐g‐PLA was 120°C for 5 h, while the optimal formulation of SEBS/PLA/BPO was 5 g/2 g/0.5 g in 30 mL chloroform. The properties and microstructures of the obtained SEBS‐g‐PLA copolymers were also studied. The tensile strength and elongation at break were higher than that of pure SEBS and improved with the increase of grafting degree. In addition, SEBS‐g‐PLA copolymer possessed two‐phase structure with vague phase boundaries. The as‐prepared SEBS‐g‐PLA copolymers can be used as the toughening component to improve the impact strength of PLA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Functionalization of high‐density polyethylene in the molten state by glycidyl methacrylate grafting

:This study concerns the melt‐free radical grafting of glycidyl methacrylate (GMA) onto high‐density polyethylene (HDPE). We studied the effect of two initiators (tert‐butyl cumyl peroxide and di‐tert‐butyl peroxide) onto HDPE. Crosslinking of polymer was observed in the presence of 0.3 wt % tert‐butyl cumyl peroxide but not with 0.3 wt % di‐tert‐butyl peroxide. The grafting was carried out in a Brabender batch mixer at 190 °C. The grafting yield of GMA onto HDPE (determined by infrared spectrometry) is weak (<1 wt % for an initial concentration in monomer of 6 wt %). Moreover, it was noted that the degree of grafting did not vary with the concentration and the nature of peroxide used. To increase the grafting yield of GMA, we added to the HDPE/peroxide/GMA system an electron‐donating monomer, such as styrene. Adding this comonomer multiplied the rate of grafted GMA 3‐ or 4‐fold, resulting in a ratio [styrene]_i/[GMA]_i = 1 mol/mol with [GMA]_i = 6 wt %. So, the copolymerization is favored compared with the homopolymerization. This kind of copolymer presenting reactive functions is very attractive in the field of compatibilizing immiscible polymers. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 581–590, 2001     

Silica‐modified SBR/BR blends

The purpose of this article is that the silica‐modified SBR/BR blend replaces natural rubber (NR) in some application fields. The styrene‐butadiene rubber (SBR) and cis‐butadiene rubber (BR) blend was modified, in which silica filler was treated with the r‐Aminopropyltriethoxysilane (KH‐550) as a coupling agent, to improve mechanical and thermal properties, and compatibilities. The optimum formula and cure condition were determined by testing the properties of SBR/BR blend. The properties of NR and the silica‐modified SBR/BR blend were compared. The results show that the optimum formulawas 80/20 SBR/BR, 2.5 phr dicumyl peroxide (DCP), 45 phr silica and 2.5 mL KH‐550. The best cure condition was at 150°C for 25 min under 10 MPa. The mechanical and thermal properties of SBR/BR blend were obviously modified, in which the silica filler treated with KH‐550. The compatibility of SBR/BR blend with DCP was better than those with benzoyl peroxide (BPO) and DCP/BPO. The crosslinking bonds between modified silica and rubbers were proved by Fourier transform infrared analysis, and the compatibility of SBR and BR was proved by polarized light microscopy (PLM) analysis. The silica‐modified SBR/BR blend can substitute for NR in the specific application fields. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Oil absorbents based on styrene–butadiene rubber

Four oil absorbents based on styrene–butadiene (SBR)—pure SBR (PS), 4‐tert‐butylstyrene–SBR (PBS), EPDM–SBR network (PES), and 4‐tert‐butylstyrene‐EPDM‐SBR (PBES)—were produced from crosslinking polymerization of uncured styrene–butadiene rubber (SBR), 4‐tert‐butylstyrene (tBS), and ethylene–propylene–diene terpolymer (EPDM). The reaction took place in toluene using benzoyl peroxide (BPO) as an initiator. Uncured SBR was used as both a prepolymer and a crosslink agent in this work, and the crosslinked polymer was identified by IR spectroscopy. The oil absorbency of the crosslinked polymer was evaluated with ASTM method F726‐81. The order of maximum oil absorbency was PBES > PBS > PES > PS. The maximum values of oil absorbency of PBES and PBS were 74.0 and 69.5 g/g, respectively. Gel fractions and swelling kinetic constants, however, had opposite sequences. The swelling kinetic constant of PS evaluated by an experimental equation was 49.97 × 10^?2 h^?1. The gel strength parameter, S, the relaxation exponent, n, and the fractal dimension, d_f, of the crosslinked polymer at the pseudo‐critical gel state were determined from oscillatory shear measurements by a dynamic rheometer. The morphologies and light resistance properties of the crosslinked polymers were observed, respectively, with a scanning electron microscope (SEM) and a color difference meter.     

Rapid FTIR method for quantification of styrene‐butadiene type copolymers in bitumen

The mid‐IR molar absorptivity for polystyrene (PS) and polybutadiene (PB) blocks were obtained for five styrene‐butadiene‐styrene (SBS) and SB copolymers, including linear, branched, and star copolymers, and their blends with bitumen. The average absorptivity for PS and PB blocks was 277 and 69 L mol⁻¹ cm⁻¹ and it was little affected by the S/B ratio or the copolymer architecture. In the presence of bitumen, Beer's law was obeyed but the respective PS and PB absorptivity was 242 and 68 L mol⁻¹ cm⁻¹, possibly because of weak interactions between the copolymer and bitumen. The absorptivity values were used to calculate the concentration of SB‐type copolymers in blends with bitumen with an accuracy of 10% or better. The method can be used to probe the stability of bitumen–copolymer blends in storage at 165°C, to determine the copolymer concentration in commercial polymer modified bitumen (PMB), and to assess the resistance of PMB to weathering. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1034–1041, 2001     

Toughening of cyanate ester resin by N‐phenylmaleimide–N‐(p‐hydroxy)phenyl‐maleimide–styrene terpolymers and their hybrid modifiers

N‐Phenylmaleimide–N‐(p‐hydroxy)phenylmaleimide–styrene terpolymer (HPMS), carrying reactive p‐hydroxyphenyl groups, was prepared and used to improve the toughness of cyanate ester resins. Hybrid modifiers composed of N‐phenylmaleimide–styrene copolymer (PMS) and HPMS were also examined for further improvement in toughness. Balanced properties of the modified resins were obtained by using the hybrid modifiers. The morphology of the modified resins depends on HPMS structure, molecular weight and content, and hybrid modifier compositions. The most effective modification of the cyanate ester resin was attained because of the co‐continuous phase structure of the modified resin. Inclusion of the modifier composed of 10 wt% PMS (M_w 136 000 g mol^?1) and 2.5 wt% HPMS (hydroxyphenyl unit 3 mol%, M_w 15 500 g mol^?1) led to 135% increase in the fracture toughness (K_IC) for the modified resin with a slight loss of flexural strength and retention of flexural modulus and glass transition temperature, compared with the values for the unmodified resin. Furthermore, the effect of the curing conditions on the mechanical and thermal properties of the modified resins was examined. The toughening mechanism is discussed in terms of the morphological and dynamic viscoelastic behaviour of the modified cyanate ester resin system. © 2001 Society of Chemical Industry     

One pot synthesis of xanthan gum‐g‐N‐vinyl‐2‐pyrrolidone and study of their metal ion sorption behavior and water swelling property

In this article, graft copolymerization of N‐vinyl‐2‐pyrrolidone onto xanthan gum initiated by potassium peroxydiphosphate/Ag⁺ system in an aqueous medium has been studied under oxygen free nitrogen atmosphere. Grafting ratio, grafting efficiency, and add on increase on increasing the concentration of potassium peroxydiphosphate (2.0 × 10^?3 to 12 × 10^?3 mol dm^?3), Ag⁺(0.4 × 10^?3 to 2.8 × 10^?3 mol dm^?3), and hydrogen ion concentration from 2 × 10^?3 to 14.0 × 10^?3 mol dm^?3. Maximum grafting has been obtained when xanthan gum and monomer concentration were 0.4 g dm^?3 and 16 × 10^?2 mol dm^?3, respectively, at 35°C and 120 min. Water swelling capacity, swelling ratio, metal ion uptake, and metal retention capacity have also been studied, and it has been found that graft copolymer shows enhancement in these properties than pure xanthan gum. The graft copolymer has been characterized by FTIR and thermal analysis. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Domain structure and miscibility studies of blends of styrene–butadiene–styrene block copolymers (SBS) and styrene–glycidyl methacrylate statistical copolymers (PS‐GMA) using SAXS and DMTA

The domain structure and miscibility in the solid state of a series of blends of styrene‐butadiene‐styrene (SBS) block copolymers and styrene‐glycidyl methacrylate (PS‐GMA) statistical copolymers with varying molecular weights and compositions were studied using small angle X‐ray scattering and dynamic mechanical thermal analysis. Depending on the molecular characteristics of each component, different types and degrees of solubilization of PS‐GMA in SBS were found which, in addition to the initially SBS phase morphology, lead to materials with multiphase domain morphologies with differences in size and structure. The degree of solubilization of PS‐GMA into the PS domains of SBS was found to be higher for blends containing PS‐GMA with lower molecular weight (M_w = 18 100 g mol^?1) and lower GMA content (1 wt%) and/or for SBS with higher PS content (39 wt%) and longer PS blocks (M_w = 19 600 g mol^?1). Localized solubilization of PS‐GMA in the middle of PS domains of SBS was found to be the most probable to occur for the systems under study, causing swelling of PS domains. However, uniform solubilization was also observed for SBS/PS‐GMA blends containing SBS with composition in the range of a morphological transition (PS block M_w = 19 600 g mol^?1 and 39 wt% of PS) causing a morphological transition in the SBS copolymer (cylinder to lamella). Copyright © 2006 Crown in the right of Canada. Published by John Wiley & Sons, Ltd     

Morphology of pyrolyzed polystyrene–isoprene–styrene and polystyrene–butadiene–styrene block copolymers

The surface morphology of thermooxidative‐degraded polystyrene–isoprene–styrene (SIS) and polystyrene–butadiene–styrene (SBS) thermoplastic block copolymers were studied by scanning electron microscopy. Surface changes caused by heating the samples in a pyrolizer for 15 and 30 min were presented in different micrographs. The morphological changes occurring due to the formation of polar groups and their crossing linking during the thermooxidative degradation are discussed. Morphological study of these thermally degraded polymer samples show very good correlation with the thermodegradation results. The rate of thermodegradation is fast in case of SBS compared with SIS block copolymer. ©2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006