Synthesis and characterization of greenish‐blue emitting vinyl copolymer containing pyrene and triarylamine moieties

Two fluorescent monomers N‐phenyl‐N‐(4‐vinylphenyl)pyren‐1‐amine (vinyl‐PyPA) and 1‐vinyl pyrene (VPy) were synthesized in good yields. A series of soluble conductive vinyl copolymers P(PyPA‐co‐VPy) containing vinyl‐PyPA and VPy moieties in different composition ratios were prepared by free radical solution polymerization. These copolymers showed high T_g (190?201 °C) and good thermal stability. The photoluminescence emission maxima of the copolymers were all in the range 474.5?478.5 nm, which was similar to the poly(N‐phenyl‐N‐(4‐vinylphenyl)pyren‐1‐amine) (P(PyPA)) (475 nm) but blue shifted compared with poly(1‐vinyl pyrene) (PVPy) (490.5 nm). The lifetime of the copolymers increased from 10.2 to 29.7 ns with an increase in pyrene content. The copolymers had higher quantum yields (0.51) than those of the homopolymers of P(PyPA) (0.48) and PVPy (0.13). The highest occupied molecular orbital of the copolymers remained relatively unchanged from P(PyPA), while the lowest unoccupied molecular orbital varied from ?2.41 eV to ?2.51 eV with an increase in pyrene ratio in the copolymers. The energy bandgaps of the copolymers (from 2.70 eV to 2.81 eV) were smaller than those of P(PyPA) (2.82 eV) and PVPy (3.47 eV). Two polymer light‐emitting diode (PLED) series were attempted including indium tin oxide (ITO) (fluorocarbon (CFx) treated)/P(PyPA‐co‐VPy)/LiF/Al and ITO(CFx treated)/P(PyPA‐co‐VPy)/1,3,5‐Tri(1‐phenyl‐1H‐benzo[d]imidazol‐2‐yl)phenyl (TPBi)/LiF/Al. The results suggested that the PyPA moiety is hole conducting and the PLEDs can achieve high luminance from 650 to 1150 cd m^?2 (at 100 mA cm^?2) only when an electron injecting layer TPBi is employed. © 2013 Society of Chemical Industry     

Specific interactions in 4‐hydroxybenzoic acid/poly(2‐vinylpyridine)/poly(N‐vinyl‐2‐pyrrolidone) blends

The specific interactions in ternary 4‐hydroxybenzoic acid (HBA)/poly(2‐vinylpyridine) (P2VPy)/poly(N‐vinyl‐2‐pyrrolidone) (PVP) blends were studied by differential scanning calorimetry, Fourier transform infrared (FTIR) spectroscopy, and electron microscopy. FTIR study shows the existence of hydrogen‐bonding interactions between HBA and P2VPy as well as PVP. The addition of a sufficiently large amount of HBA produces a blend showing one glass‐transition temperature (T_g). Microscopic study shows a drastic reduction in domain size in single‐T_g blends. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 901–907, 2001     

Miscibility and specific interactions in blends of poly(4-vinylphenol-co-methyl methacrylate)/poly(styrene-co-4-vinylpyridine)

The miscibility and phase behavior of poly(4-vinylphenol-co-methyl methacrylate) (PVPhMMA50) containing 50% of methyl methacrylate with random copolymers of poly(styrene-co-4-vinylpyridine) (PS4VPy) containing 5, 15, 30, 40, and 100% of 4-vinylpyridine, respectively, were investigated by differential scanning calorimetry, Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). It was shown that for a composition of 4-vinylpyridine less than 30%, all blends of PVPhMMA50/PS4VPy are immiscible, characterized by the apparition of two glass transitions (T_g) over their entire composition range. However, above this composition, a single T_g has been observed in all the blends of PVPhMMA50 and PS4VPy. When the amount of vinylpyridine exceeds to 40% in PS4VPy, the obtained T_gs of PVPhMMA50/PS4VPy blends were found to be significantly higher than those observed for each individual component of the mixture indicating that these blends are able to form interpolymer complexes. FTIR analysis reveals the existence of preferential specific interactions via hydrogen bonding between the hydroxyl and pyridyl groups and intensifies when the amount of 4VPy is increased in PS4VPy copolymers. Furthermore, the quantitative FTIR study carried out for PVPhMMA50/PS4VPy blends was also performed for the vinylphenol and vinylpyridine functional groups. These results were also confirmed by SEM study. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

The phase behavior and thermal stability of blends of poly(styrene‐co‐methacrylic acid)/poly(styrene‐co‐ 4‐vinylpyridine)

The hydrogen bonding and miscibility behaviors of poly(styrene‐co‐methacrylic acid) (PSMA20) containing 20% of methacrylic acid with copolymers of poly(styrene‐co‐4‐vinylpyridine) (PS4VP) containing 5, 15, 30, 40, and 50%, respectively, of 4‐vinylpyridine were investigated by differential scanning calorimetry, thermogravimetric analysis (TGA), and Fourier transform infrared spectroscopy (FTIR). It was shown that all the blends have a single glass transition over the entire composition range. The obtained T_gs of PSMA20/PS4VP blends containing an excess amount of PS4VP, above 15% of 4VP in the copolymer, were found to be significantly higher than those observed for each individual component of the mixture, indicating that these blends are able to form interpolymer complexes. The FTIR study reveals presence of intermolecular hydrogen‐bonding interaction between vinylpyridine nitrogen atom and the hydroxyl of MMA group and intensifies when the amount of 4VP is increased in PS4VP copolymers. A new band characterizing these interactions at 1724 cm⁻¹ was observed. In addition, the quantitative FTIR study carried out for PSMA20/PS4VP blends was also performed for the methacrylic acid and 4‐vinylpyridine functional groups. The TGA study confirmed that the thermal stability of these blends was clearly improved. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Miscibility and crystallization kinetics of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)/ poly(methyl methacrylate) blends

The miscibility and crystallization kinetics of the blends of random poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) [P(HB‐co‐HV)] copolymer and poly(methyl methacrylate) (PMMA) were investigated by differential scanning calorimetry (DSC) and polarized optical microscopy (POM). It was found that P(HB‐co‐HV)/PMMA blends were miscible in the melt. Thus the single glass‐transition temperature (T_g) of the blends within the whole composition range suggests that P(HB‐co‐HV) and PMMA were totally miscible for the miscible blends. The equilibrium melting point (T°_m) of P(HB‐co‐HV) in the P(HB‐co‐HV)/PMMA blends decreased with increasing PMMA. The T°_m depression supports the miscibility of the blends. With respect to the results of crystallization kinetics, it was found that both the spherulitic growth rate and the overall crystallization rate decreased with the addition of PMMA. The kinetics retardation was attributed to the decrease in P(HB‐co‐HV) molecular mobility and dilution of P(HB‐co‐HV) concentration resulting from the addition of PMMA, which has a higher T_g. According to secondary nucleation theory, the kinetics of spherulitic crystallization of P(HB‐co‐HV) in the blends was analyzed in the studied temperature range. The crystallizations of P(HB‐co‐HV) in P(HB‐co‐HV)/PMMA blends were assigned to n = 4, regime III growth process. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3595–3603, 2004     

Phase behavior of binary and ternary blends of poly(styrene‐co‐methacrylic acid), poly(styrene‐co‐4‐vinylpyridine), and poly(2,6‐dimethyl‐1,4‐phenylene oxide)

Poly(styrene‐co‐methacrylic acid) (PSMA) and poly(styrene‐co‐4‐vinylpyridine) (PS4VP) of different compositions were prepared and characterized. The phase behavior of these copolymers as binary PSMA/PS4VP mixtures or with poly(2,6‐dimethyl‐1,4‐phenylene oxide) (PPO) as PPO/PSMA or PPO/PS4VP and PPO/PSMA/PS4VP ternary blends was investigated by differential scanning calorimetry (DSC). This study showed that PPO was miscible with PS4VP containing up to 15 mol % 4‐vinylpyridine (4VP) but immiscible with PS4VP‐30 (where the number following the hyphen refers to the percentage 4VP in the polymer) and PSMA‐20 (where the number following the hyphen refers to the percentage methacrylic acid in the polymer) over the entire composition range. To examine the morphology of the immiscible blends, scanning electron microscopy was used. Because of the hydrogen‐bonding specific interactions that occurred between the carboxylic groups of PSMA and the pyridine groups of PS4VP, chloroform solutions of PSMA‐20 and PS4VP‐15 formed interpolymer complexes. The obtained glass‐transition temperatures (T_g's) of the PSMA‐20/PS4VP‐15 complexes were found to be higher than those calculated from the additivity rule. Although, depending on the content of 4VP, the shape of the T_g of the PPO/PS4VP blends changed from concave to S‐shaped in the case of the miscible blends, two T_g were observed with each PPO/PS4VP‐30 and PPO/PS4VP‐40 blend. The thermal stability of the PSMA‐20/PS4VP‐15 interpolymer complexes was studied by thermogravimetry. On the basis of the obtained results, the phase behavior of the ternary PPO/PSMA‐20/PS4VP‐15 blends was investigated by DSC. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Morphology and thermal behavior of organo‐bentonite clay/poly(styrene‐co‐methacrylic acid)/poly(isobutyl methacrylate‐co‐4‐vinylpyridine) nanocomposites

Poly(styrene‐co‐methacrylic acid) containing 29 mol % of methacrylic acid (SMA‐29) and poly(isobutyl methacrylate‐co‐4‐vinylpyridine) containing 20 mol % of 4‐vinylpyridine (IBM4VP‐20) were synthesized, characterized, and used to elaborate binary and ternary nanocomposites of different ratios with a 3% by weight hexadecylammonium‐modified bentonite from Maghnia (Algeria) by casting method from tetrahydrofuran (THF) solutions. The morphology and the thermal behavior of these binary and ternary elaborated nanocomposites were investigated by X‐ray diffraction, scanning electron microscopy, FTIR spectroscopy, differential scanning calorimetry, and thermogravimetry. Polymer nanocomposites and nanoblends of different morphologies were obtained. The effect of the organoclay and its dispersion within the blend matrix on the phase behavior of the miscible SMA29/IBM4VP20 blends is discussed. The obtained results showed that increasing the amount of SMA29 in the IBM4VP20/SMA29 blend leads to near exfoliated nanostructure with significantly improved thermal stability. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation and characterization of acrylonitrile‐ethyl methacrylate copolymers and the effect of LiClO4 salt on electrical properties of copolymer films

Copolymers of poly(acrylonitrile‐co‐ethyl methacrylate), P(AN‐EMA), with three different EMA content and parent homopolymers were synthesized by emulsion polymerization. The chemical composition of copolymers were identified by FTIR, ¹H‐NMR and ¹³C‐NMR spectroscopy. The thermal properties of copolymers were modified by changing the EMA content in copolymer compositions. Various amounts of LiClO₄ salt loaded (PAN‐co‐PEMA) copolymer films were prepared by solution casting. The dielectric properties of these films at different temperatures and frequencies were investigated. It was found that the dielectric constant and ac‐conductivity of copolymer films were strongly influenced by the salt amounts and EMA content in copolymers. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Blends containing amphiphilic polymers IV. Poly(N‐1‐alkyl itaconamic acids) with poly(2‐vinylpyridine) and poly(4‐vinylphenol)

The phase behavior of blends containing Poly(N‐1‐alkyl itaconamic acids) (PNAIA) with Poly(2‐vinylpyrindine) (P2VPy) and Poly(4‐vinylphenol) (P4VPh) were analyzed by Diferential Scanning Calorimetry (DSC) and Fourier Transform Infrared Spectroscopy (FTIR). Miscibility over the whole range of compositions is observed in both systems. All the blends show thermograms exhibiting distinct single glass transition temperatures (T_g), which are intermediate to those of the pure components. The Calorimetric Analysis using Gordon Taylor, Couchman, and Kwei treatments allows conclusion that interactions between the components is favorable to the miscibility. FTIR analysis of the blends suggests that the driving force for miscibility is hydrogen bonding formation. The variation of the absorptions of the carbonyl groups of PNAIA and the hydroxyl groups of P4VPh allows one to attribute the miscibility to weak acid base like interactions. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1245–1250, 2002; DOI 10.1002/app.10453     

Water‐soluble copolymers. I. Biodegradability and functionality of poly[(sodium acrylate)‐co‐(4‐vinylpyridine)]

As a biodegradable functional polymer, poly[(sodium acrylate)‐co‐(4‐vinylpyridine)] [P(SA‐co‐4VP)] containing a small amounts of 4‐vinylpyridine groups were prepared and their biodegradability, dispersity, and complex performance were analyzed. The polymers can be useful as detergent builders and dispersants. It was found that the biodegradation of P(SA‐co‐4VP) was more conspicuous when content of the 4‐vinylpyridine in the copolymer was larger. This indicates that the 4‐vinylpyridine, which acts as biodegradable segments, should be incorporated into the polymer main chain in such a manner that they are digested by activated sludge. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1953–1957, 1999     

Miscibility and crystallization behavior of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)/poly(vinyl acetate) blends

The miscibility and crystallization behavior of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (P(HB‐co‐HV))/poly(vinyl acetate) (PVAc) blends have been investigated by differential scanning calorimetry (DSC) and polarized optical microscopy (POM). It was found that P(HB‐co‐HV)/PVAc blends were miscible in the melt over the whole compositions. Thus the blend exhibited a single glass transition temperature (T_g), which increased with increasing PVAc composition. The spherulitic morphologies of P(HB‐co‐HV)/PVAc blends indicated that the PVAc was predominantly segregated into P(HB‐co‐HV) interlamellar or interfibrillar regions during P(HB‐co‐HV) crystallization because of the volume‐filled spherulites. As to the crystallization kinetics study, it was found that the overall crystallization and crystal growth rates decreased with the addition of PVAc. The kinetics retardation was primarily attributed to the reduction of chain mobility and dilution of P(HB‐co‐HV) upon mixing with higher T_g PVAc. The overall crystallization rate was predominantly governed by the spherulitic growth rate and promoted by the samples treated with the quenched state because of the higher nucleation density. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 980–988, 2006     

Polymer nanocomposites containing carbon nanotubes and miscible polymer blends based on poly[ethylene‐co‐(acrylic acid)]

Four binary polymer blends containing poly [ethylene‐co‐(acrylic acid)] (PEAA) as one component, and poly(4‐vinyl phenol‐co‐2‐hydroxy ethyl methacrylate) (P4VPh‐co‐2HEMA) or poly(2‐ethyl‐2‐oxazoline) (PEOx) or poly(vinyl acetate‐co‐vinyl alcohol) (PVAc‐co‐VA) or poly (vinylpyrrolidone‐co‐vinyl acetate) (PVP‐co‐VAc) as the other component were prepared and used as a matrix of a series of composite materials. These binary mixtures were either partially or completely miscible within the composition range studied and were characterized by differential scanning calorimetry (DSC) and Fourier transformed infrared spectroscopy (FTIR). Carbon nanotubes (CNTs) were prepared by a thermal treatment of polyester synthesized through the chemical reaction between ethylene glycol and citric acid over an alumina boat. High resolution transmission electron microscopy (HRTEM) was used to characterize the synthesized CNTs. Films of composite materials containing CNTs were obtained after evaporation of the solvent used to prepare solutions of the four types of binary polymer blends. Young's moduli of the composites were obtained by thermomechanical analysis at room temperature. Only one glass transition temperature was detected for several compositions on both binary blends and the composite material matrices. Evidence of hydrogen bond formation was recorded for both miscible blends and composite materials. The degree of crystallinity and Young's moduli of the CNT‐polymer composites increased compared to the single polymer blends. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Poly(dimethylsiloxane)urethane‐co‐poly(methyl methacrylate) with 2,4‐toluene diisocyanate and m‐xylene diisocyanate. I. Compatibility and impact strength of copolymers

In this study, slightly crosslinked poly(dimethylsiloxane)urethane‐co‐poly(methyl methacrylate) (PDMS urethane‐co‐PMMA) graft copolymers based on two diisocyanates, 2,4‐toluene diisocyanate (2,4‐TDI) and m‐xylene diisocyanate (m‐XDI), were successfully synthesized. Glass‐transition behaviors of the copolymers were investigated. Results confirm that PDMS–urethane and PMMA are miscible in the 2,4‐TDI system, but are only partially miscible in the m‐XDI system. The methylene groups adjoining the isocyanate in the m‐XDI system show increased phase‐separation behavior over the 2,4‐TDI system, in which the benzene ring adjoins the isocyanate. The functional group of PDMS–urethane improves the impact strength of the copolymers. The toughness depends on the compatibility of PDMS–urethane and PMMA segments in the copolymers. In the m‐XDI system, the impact strength of the copolymer containing 3.75 phr macromonomer achieves a maximum value (from 13.02 to 22.21 J/m). The fracture behavior and impact strength of the copolymers in the 2,4‐TDI system are similar to that of PMMA homopolymer, although they are independent of the macromonomer content in the copolymer. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1875–1885, 2002     

Mechanical properties–morphology relationships in nano‐/microstructured epoxy matrices modified with PEO–PPO–PEO block copolymers

Epoxy‐based blends containing poly(ethylene oxide)‐co‐poly(propylene oxide)‐co‐poly(ethylene oxide) (PEO–PPO–PEO) block copolymers with different PEO/PPO molar ratios have been investigated in order to analyze the effect of the generated morphologies and interactions between components on the mechanical properties of the blends. Mechanical, morphological and dynamic mechanical analyses indicate that the observed increase of flexural modulus can be related to the decrease of free volume. In modified systems that remain miscible, an increase of flexural modulus, strength and fracture toughness can be observed. Also, macrophase‐ and microphase‐separated systems show an increase of fracture toughness but not of flexural modulus and strength at low contents of block copolymers. Copyright © 2007 Society of Chemical Industry     

Miscibility and intermolecular hydrogen‐bonding interactions in poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate)/poly(4‐vinyl phenol) binary blends

The miscibility and hydrogen bonding interaction in the poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate)/poly(4‐vinyl phenol) [P(3HB‐co‐3HH)/PVPh] binary blends were investigated by differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FTIR). The DSC results indicate that P(3HB‐co‐3HH) with 20 mol % 3HH unit content is fully miscible with PVPh, and FTIR studies reveal the existence of hydrogen bonding interaction between the carbonyl groups of P(3HB‐co‐3HH) and the hydroxyl groups of PVPh. The effect of blending of PVPh on the mechanical properties of P(3HB‐co‐3HH) were studied by tensile testing. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis and properties of poly(acrylonitrile‐co‐p‐trimethylsilylstyrene) and poly(acrylonitrile‐co‐p‐trimethylsilylstyrene‐co‐styrene)

Copolymerization of acrylonitrile (AN) with p‐trimethylsilylstyrene (TMSS) was carried out at 60°C in bulk and in solution in the presence of 2,2′‐azobisisobutyronitrile (AIBN). The reactivity ratios of AN (M₁) and TMSS (M₂) were determined to be r₁ = 0.068 and r₂ = 0.309. The effects of the AIBN concentration and that of the chain transfer agent CCl₄ on the molecular weights (MWs) of the copolymers were investigated. An increase in the concentrations of AIBN or CCl₄ in solution led to a decrease in MW. Poly(AN‐co‐TMSS‐co‐St) was synthesized in solution using AIBN as the initiator. The molar fraction of AN was 0.415, while the molar ratio of TMSS/St varied from 1 : 1 to 1 : 9. The transition temperatures and thermal and thermooxidative stabilities of poly(AN‐co‐TMSS) and poly(AN‐co‐TMSS‐co‐St) were investigated. The differential scanning calorimeter technique was used to determine the compatibility of the poly(AN‐co‐TMSS) and poly(AN‐co‐TMSS‐co‐St) with commercial poly(AN‐co‐St). All the blends show a single glass transition temperature, which indicates the compatibility of the blend components. The surface film morphology of the blends mentioned above was examined by X‐ray photoelectron spectroscopy. The data obtained indicate that the silicon‐containing copolymer is concentrated in the surface layer. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1920–1928, 2000     

Studies on blends of LLDPE and polar polymers compatibilized by a random copolymer

Compatibilization of blends of linear low‐density polyethylene (LLDPE)–poly(methyl methacrylate) (PMMA) and LLDPE–copolymer of methyl methacrylate (MMA) and 4‐vinylpyridine (poly(MMA‐co‐4VP) with poly(ethylene‐co‐methacrylic acid) (EMAA) have been studied. Mechanical properties of the LLDPE–PMMA blends increase upon addition of EMAA. In order to further improve interfacial adhesion of LLDPE and PMMA, 4‐vinyl pyridine units are introduced into PMMA chains, or poly(MMA‐co‐4VP) is used as the polar polymer. In LLDPE–poly(MMA‐co‐4VP)–EMAA blends, interaction of MAA in EMAA with 4VP of poly(MMA‐co‐4VP) causes a band shift in the infrared (IR) spectra. Chemical shifts of N_1s binding energy in X‐ray photoelectronic spectroscopy (XPS) experiments indicate a transfer of proton from MAA to 4VP. Scanning electron microscopy (SEM) pictures show that the morphology of the blends were improved upon addition of EMAA. Nonradiative energy transfer (NRET) fluorescence results attest that there exists interdiffusion of chromophore‐labeled LLDPE chains and chromophore‐labeled poly(MMA‐co‐4VP) chains in the interface. Based on experimental results, the mechanism of compatibilization is studied in detail. Compatibilization is realized through the interaction between MAA in EMAA with 4VP in poly(MMA‐co‐4VP). © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 967–973, 1999     

Interpolymer‐specific interactions and miscibility in poly(styrene‐co‐acrylic acid)/poly(styrene‐co‐N,N‐dimethylacrylamide) blends

The miscibility or complexation of poly(styrene‐co‐acrylic acid) containing 27 mol % of acrylic acid (SAA‐27) and poly(styrene‐co‐N,N‐dimethylacrylamide) containing 17 or 32 mol % of N,N‐dimethylacrylamide (SAD‐17, SAD‐32) or poly(N,N‐dimethylacrylamide) (PDMA) were investigated by different techniques. The differential scanning calorimetry (DSC) analysis showed that a single glass‐transition temperature was observed for all the mixtures prepared from tetrahydrofuran (THF) or butan‐2‐one. This is an evidence of their miscibility or complexation over the entire composition range. As the content of the basic constituent increases as within SAA‐27/SAD‐32 and SAA‐27/PDMA, higher number of specific interpolymer interactins occurred and led to the formation of interpolymer complexes in butan‐2‐one. The qualitative Fourier transform infrared (FTIR) spectroscopy study carried out for SAA‐27/SAD‐17 blends revealed that hydrogen bonding occurred between the hydroxyl groups of SAA‐27 and the carbonyl amide of SAD‐17. Quantitative analysis carried out in the 160–210°C temperature range for the SAA‐27 copolymer and its blends of different ratios using the Painter–Coleman association model led to the estimation of the equilibrium constants K₂, K_A and the enthalpies of hydrogen bond formation. These blends are miscible even at 180°C as confirmed from the negative values of the total free energy of mixing ΔG_M over the entire blend composition. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1011–1024, 2007     

Blue fluorescent conductive poly(9,10‐di(1‐naphthalenyl)‐2‐vinylanthracene) homopolymer and its highly soluble copolymers with styrene or 9‐vinylcarbazole

A new blue fluorescent monomer, 9,10‐di(1‐naphthalenyl)‐2‐vinylanthracene, was designed and synthesized in good yield. Its homopolymer poly(9,10‐di(1‐naphthalenyl)‐2‐vinylanthracene) (P(ADN)) and soluble conductive vinyl copolymers poly[(9,10‐di(1‐naphthalenyl)‐2‐vinylanthracene)‐co‐styrene] (P(ADN‐co‐S)) and poly[(9,10‐di(1‐naphthalenyl)‐2‐vinylanthracene)‐co‐(9‐vinylcarbazole)] (P(ADN‐co‐VK)) were synthesized using free radical solution polymerization. All the polymers showed high glass transition mid‐point temperatures (203 to 237 °C) and good thermal stabilities. The photoluminescence emission of the copolymers was similar to that of P(ADN) (with two maxima at 423 and 442 nm). The lifetimes of P(ADN‐co‐S) (6.82 to 7.91 ns) were all slightly less than that of P(ADN) (8.40 ns). The lifetime of P(ADN‐co‐VK) increased from 7.8 to 8.8 ns with an increase in VK content. The fluorescence quantum yields of P(ADN‐co‐S) showed an overall increasing tendency from 0.42 to 0.58. The quantum efficiencies of P(ADN‐co‐VK) decreased from 0.36 to 0.19 with an increase of VK fraction. With increasing S/VK content, the highest occupied molecular orbital of P(ADN‐co‐S)/P(ADN‐co‐VK) ranged from ?5.58 to ?5.73 eV, which was similar to that of P(ADN) (?5.71 eV). The band gaps of P(ADN‐co‐S) and P(ADN‐co‐VK) were about 2.97 eV, which were equal to that of P(ADN), and smaller than that of 2‐methyl‐9,10‐di(1‐naphthalenyl)anthracene (MADN) (3.04 eV) and poly(9‐vinylcarbazole) (3.54 eV). Preliminary electroluminescence results were obtained for a homojunction device with the configuration ITO/MoO₃ (20 nm)/P(ADN)/LiF (1 nm)/Al (100 nm), which achieved only 30–50 cd m^?2, due to P(ADN) having a low mobility of 4.7 × 10^?8 cm² V^?1 s^?1 compared to that of its model compound MADN of 6.5 × 10^?4 cm² V^?1 s^?1. © 2013 Society of Chemical Industry     

Preparation and application of sulfonated poly(1‐octene‐co‐styrene)

In this article, 1‐octene and styrene was copolymerized by the supported catalyst (TiCl₄/ID/MgCl₂). Subsequently, by sulfonation reaction, sulfonated poly(1‐octene‐co‐styrene)s which were amphiphilic copolymers were prepared. The copolymerization behavior between 1‐octene and styrene is moderate ideal behavior. Copolymers prepared by this catalyst contain appreciable amounts of both 1‐octene and styrene. Increase in the feed ratio of styrene/1‐octene leads to increase in styrene content in copolymer and decrease in molecular weight. As the polymerization temperature increases, the styrene content in the copolymers increases, however, the molecular weight decreases. Hydrogen is an efficient regulator to lower the molecular weights of poly(1‐octene‐co‐styrene)s. The sulfonation degree of the sulfonated poly(1‐octene‐co‐styrene)s increased as the styrene content in copolymer increased or the molecular weight decreased. Thirty‐six hour is long enough for sulfonation reaction. The sulfonated poly(1‐octene‐co‐styrene)s can be used as effective and durable modifying agent to improve the wettability of polyethylene film and have potential application in emulsified fuels and for the stabilization of dispersions. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011