Comparative analysis of ultrasonically devulcanized unfilled SBR,NR, and EPDM rubbers

The comparative study of the continuous ultrasonic devulcanization of various unfilled rubbers [natural rubber, styrene–butadiene rubber (SBR), ethylene–propylene–diene rubber (EPDM)] is carried out by means of a ultrasonic reactor. The power consumption, gel fraction, crosslink density, cure behavior, and physical properties of devulcanized rubbers were measured. The glass transition temperatures of virgin, vulcanized, and devulcanized rubbers were determined in order to characterize the difference in the mobility of rubber molecules for each rubber before and after devulcanization. Thermogravimetric analysis was also used to determine thermal stability of the various rubbers. A unique correlation between gel fraction and crosslink density indicated significant differences in the efficiency of devulcanization of various rubbers. Under certain devulcanization conditions, the mechanical properties of revulcanized SBR and EPDM rubbers were found to improve compared to those of the original rubbers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 434–441, 2003     

EPDM rubber reclaim from devulcanized EPDM

Two types of ethylene–propylene–diene monomer (EPDM) rubbers, namely an efficient vulcanized (EV) and a semiefficient vulcanized (SEV), have been used to produce devulcanizates in a continuous setup. The devulcanizates are re‐cured using the same recipes as for the virgin rubber. The influence of mixing it with virgin rubber compound, the addition of extra sulfur, the operating devulcanization conditions, and the excess of devulcanizing agent on the mechanical properties (hardness, tensile strength, and compression set) of the reclaim rubbers are studied. Most of the reclaims produced show slightly inferior mechanical properties compared to the virgin rubber. Surface imperfection was observed on the devulcanizate with high devulcanizing agent content. Excellent mechanical properties (all above the standards) of the reclaim were found when the devulcanized profile material was used (EV‐EPDM) to replace the virgin one for application as a roofing sheet material (SEV‐EPDM). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5948–5957, 2006     

Highly exfoliated poly(ϵ‐caprolactone)/organomontmorillonite nanocomposites prepared by in situ polymerization

Ethylene–propylene–diene rubbers (EPDM) with 2-ethylidene-5-norbornene (ENB), dicyclopentadiene (DCPD), and 1,4-hexadiene (HD) as third monomers have been vulcanized with peroxide and with a conventional sulfur vulcanization recipe, and their devulcanization was subsequently investigated for recycling purposes. The behavior of these vulcanizates during pure thermal devulcanization depends on the EPDM third monomer and the crosslinker used. Peroxide vulcanizates of ENB-EPDM devulcanize only to a small extent and predominantly by random scission, whereas peroxide vulcanizates of HD-EPDM devulcanize by crosslink scission. In contrast, sulfur vulcanizates of ENB-EPDM, devulcanize mainly by crosslink scission. During devulcanization of sulfur-cured HD-EPDM, scission of both crosslinks and main chains occurs. Sulfur-cured DCPD-EPDM cannot be devulcanized but shows further crosslinking instead. In those cases, where purely thermal devulcanization is already effective to a certain extent, diphenyldisulfide as devulcanization agent increases the effectivity during thermochemical devulcanization. Hexadecylamine as an alternative devulcanization agent is effective for ENB-EPDM but does not contribute to thermochemical devulcanization of HD-EPDM. In summary, devulcanization proceeds by different mechanisms in ENB-EPDM, DCPD-EPDM, and HD-EPDM. Explanations are given in terms of the chemical structures of the third monomers, the corresponding crosslinks, and devulcanization agents. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Modeling on the kinetics of an EPDM devulcanization in an internal batch mixer using an amine as the devulcanizing agent

The use of amines and the application of mechanical force (shear) in rubber devulcanization have been reported in the literatures. In this paper, the devulcanization of ethylene propylene diene rubber (EPDM) is conducted in a Brabender batch mixer using hexadecylamine (HDA) as the devulcanizing agent. Considering the complexity of the compound and the limitations of the analyses techniques for crosslinked systems, an engineering approach to model a devulcanization process of EPDM material is proposed. An engineering kinetic model has been derived by fitting a large number of experimental data with several models based on simple kinetic considerations. Rate determining parameters such as temperature, shear rate, reactant concentrations and time are included in the model. The model obtained covers all the phenomena happening during the devulcanization, without distinguishing them on the molecular level.     

Effects of ultrasonic oscillation on processing behaviors of PS,EPDM, and PS/EPDM blend

In this study, the extrusion processing behaviors of polystyrene (PS), ethylene–propylene–diene terpolymer (EPDM), and their blend (PS/EPDM, 80/20) were studied by using a special ultrasonic oscillation extrusion system developed in our laboratory. The die pressure and volume flow rate were measured at different ultrasonic intensities and screw rotation speeds. The dependences on ultrasonic intensity of die pressure, volume flow rate, and apparent viscosity of polymers, as well as die swell at the same screw rotation speed were investigated. The effects of screw rotation speed on the processing behaviors of polymers and their blend at the same ultrasonic intensity were also studied. The experimental results showed that in the presence of ultrasonic irradiation, the processibilities of polymers and their blend were improved. Their possible mechanism is discussed in this article. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1856–1863, 2006     

Influence of calcium carbonate filler and mixing type process on structure and properties of styrene–acrylonitrile/ethylene–propylene–diene polymer blends

The properties of styrene–acrylonitrile (SAN) and ethylene–propylene–diene (EPDM) blends containing different types of calcium carbonate filler were studied. The influence of mixing type process on the blend properties was also studied. Two different mixing processes were used. The first one includes mixing of all components together. The other process is a two‐step mixing procedure: masterbatch (MB; EPDM/SAN/filler blend) was prepared and then it was mixed with previously prepared polymer blend. Surface energy of samples was determined to predict the strength of interactions between polymer blend components and used fillers. The phase morphology of blends and their thermal and mechanical properties were studied. From the results, it can be concluded that the type of mixing process has a strong influence on the morphological, thermal, and mechanical properties of blends. The two‐step mixing process causes better dispersion of fillers in blends as well as better dispersion of EPDM in SAN matrix, and therefore, the finest morphology and improved properties are observed in blends with MB. It can be concluded that the type of mixing process and carefully chosen compatibilizer are the important factors for obtaining the improved compatibility of SAN/EPDM blends. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effects of shear stress and subcritical water on devulcanization of styrene–butadiene rubber based ground tire rubber in a twin‐screw extruder

The devulcanization reaction of styrene–butadiene rubber (SBR) based ground tire rubber (GTR) in GTR/ethylene–propylene–diene monomer rubber (EPDM) blend was investigated through a compound‐induced reaction by increasing screw rotation speed and being in the presence of subcritical water. The effects of temperature, pressure, screw rotation speed, or promoting agents on the gel content, Mooney viscosity, and Fourier transform infrared spectra of the sol of the devulcanized blends (devulcanized ground tire rubber (DGTR)/EPDM) were measured, and the mechanical properties and microstructures of the revulcanized blend ((DGTR/EPDM)/SBR) were characterized. The results show that subcritical water as a swelling agent and reaction medium promotes the devulcanization reaction, increases the selectivity of the crosslink breakage, keeps the extrusion material from oxidative degradation, reduces the gel particle size of the devulcanized blends, and significantly improves the mechanical properties of the revulcanized SBR/(DGTR/EPDM) blends. In subcritical water, the suitable promoting agents (alkylphenol polysulfide 450, hydrogen peroxide H₂O₂, or 450/H₂O₂) accelerate the devulcanization reaction, keep the double bond content, and lead to further decrease of the gel content and Mooney viscosity of the devulcanized blends and further increase of the mechanical properties of the revulcanized SBR/(DGTR/EPDM) blends. Especially the compound promoting agent (450/H₂O₂) improves the selectivity of the crosslink breakage in devulcanization of SBR‐based GTR. When 450/H₂O₂ is added as a compound promoting agent at the best reaction condition in subcritical water (200°C, 1.6 MPa and 1000 rpm), the tensile strength and elongation at break of the revulcanized SBR/(DGTR/EPDM) blends reach to 85.4% and 201% of vulcanized SBR (24.0 MPa, 356%), respectively. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1845–1854, 2013     

Continuous ultrasonic devulcanization of NR/SBR blends

The ultrasonic devulcanization of sulfur‐cured natural rubber (NR)/styrene–butadiene rubber (SBR) blends was studied with the goal of understanding the devulcanization of rubber vulcanizates in which two networks of different natures were present. Also, similarities and differences in the devulcanization behaviors of NR, SBR, and their blends were found. During the devulcanization of cured NR/SBR blends, we observed that, as for NR, the ultrasonic power consumption for 75/25 and 50/50 (w/w) NR/SBR blends passed through a maximum at 7.5 μm. For SBR and 25/75 (w/w) NR/SBR blends, the power consumption increased with increasing ultrasonic amplitude. The higher power consumption led to a higher degree of devulcanization. The crosslink densities of the devulcanized 25/75, 50/50, and 75/25 (w/w) NR/SBR blends were lower than those of the devulcanized NR and SBR, possibly because of the reduced degree of unsaturation. The tensile properties of the revulcanized blends were lower than those of the virgin vulcanized blends. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 160–168, 2002     

亚临界流体挤出法复合诱导SBR基轮胎胶脱硫化及 再硫化材料力学性能

在SBR基轮胎胶(GTR)与三元乙丙橡胶（EPDM）混合物的熔融挤出过程中,采用改变亚临界流体品种和提高螺杆转速的方法,研究了亚临界流体（水,乙醇,丙醇）、螺杆转速、烷基酚多硫化物促进剂（450）以及温度对脱硫共混物（DGTR/EPDM）凝胶含量、门尼粘度、溶胶红外光谱及脱硫共混物共混丁苯橡胶（SBR）再硫化材料（SBR/(DGTR/EPDM)）力学性能的影响,对再硫化材料的试样断面形貌也进行了SEM观察。实验结果表明：亚临界流体（水,乙醇,丙醇）作为一种溶胀剂和反应性介质能够很好地促进脱硫反应,提高交联键断裂的选择性,降低脱硫产物的凝胶含量和凝胶颗粒尺寸并明显提高脱硫共混物共混丁苯橡胶再硫化材料的力学性能,其中亚临界乙醇的作用最显著。当450作为一种脱硫促进剂,在最优亚临界乙醇挤出反应条件（200℃,1.6 MPa,600 rpm）下,脱硫共混物共混丁苯橡胶分别达到丁苯生胶混炼硫化材料拉伸强度（24.0MPa）和断裂伸长率（356%）的99.6%和209%。     

Synthesis and properties of styrene–EPDM–vinyl acetate graft polymer

The styrene–EPDM–vinylacetate (SEV) graft polymer, which linked respectively the styrene (St) unit and vinylacetate the (VAc) unit to the ethylene–propylene–diene terpolymer (EPDM) backbone was synthesized by two‐step graft polymerizations: First the graft polymerization of VAc onto EPDM was carried out, and then St was added successively in the prepolymerized solution and further polymerized for a given period to obtain SEV. The effects of concentration of EPDM and an initiator, mole ratio of VAc to St, polymerization time, temperature, and solvent were examined on the graft polymerizations. The synthesized graft polymers (SEVs) that have different contents of St or VAc were identified by Fourier transform IR spectrum. The highest graft ratio has been obtained by 10 wt % of EPDM, 1.0 mole ratio of VAc to St, and 1.0 wt % of BPO in toluene for 48 h at 70°C. The glass transition temperature of SEV is lower than that of poly(vinyl acetate) (PVAc) and polystyrene (PS). The thermal stability of SEV is higher than that of PVAc, PS, and the acrylonitrile–butadiene–styrene (ABS) resin. The tensile strength of SEV was improved as compared with that of EPDM. The light resistance and weatherability of SEV were better than those of ABS. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2296–2304, 2000     

Recycling of roofing membrane rubber by ultrasonic devulcanization

The recycling of vulcanizates based on EPDM roofing membrane rubber using a new ultrasonic devulcanization reactor with a grooved barrel was carried out. This reactor provided continuous devulcanization at an output as high as 2.52 g/s. Die pressure and ultrasonic power consumption were measured as a function of processing conditions. The mechanical properties of virgin vulcanized and revulcanized roofing membranes were measured. Tensile strength of the revulcanized rubber was found to be similar to that of the virgin vulcanizate. Gel fraction, crosslink density, and dynamic properties of the virgin vulcanizate, the ultrasonically devulcanized rubber, and the revulcanized rubber were determined. Also, dynamic properties and the cure behavior of the virgin compound and of the devulcanized roofing membrane were investigated. All these properties were found to be dependent on processing conditions during devulcanization. The thermal stability of the virgin compound, virgin vulcanizate, and devulcanized and revulcanized rubbers were studied by means of TGA. It was found that the thermal stability of all the vulcanizates in air and nitrogen environments remained practically intact, while that of devulcanized rubber in air environment was a function of processing conditions.     

Synthesis and evaluation of high‐performance ethylene–propylene–diene terpolymer/organoclay nanoscale composites

The main objective of this study was to synthesize and characterize the properties of ethylene–propylene–diene terpolymer (EPDM)/clay nanocomposites. Pristine clay, sodium montmorillonite (Na⁺–MMT), was intercalated with hexadecyl ammonium ion to form modified organoclay (16Me–MMT) and the effect of intercalation toward the change in interlayer spacing of the silicate layers was studied by X‐ray diffraction, which showed that the increase in interlayer spacing in Na⁺–MMT by 0.61 nm is attributed to the intercalation of hexadecyl ammonium ion within the clay layers. In the case of EPDM/16Me–MMT nanocomposites, the basal reflection peak was shifted toward a higher angle. However, gallery height remained more or less the same for different EPDM nanocomposites with organoclay content up to 8 wt %. The nanostructure of EPDM/clay composites was characterized by transmission electron microscopy, which established the coexistence of intercalated and exfoliated clay layers with an average layer thickness in the nanometer range within the EPDM matrix. The significant improvement in thermal stability and mechanical properties reflects the high‐performance nanocomposite formation. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2429–2436, 2004     

Radiation‐processed polychloroprene‐co‐ethylene–propene diene terpolymer blends: Evaluation of blend morphology,miscibility, and physical properties

The miscibility of polychloroprene rubber (CR) and ethylene–propylene–diene terpolymer rubber (EPDM) was studied over the entire composition range. Different blend compositions of CR and EPDM were prepared by initially mixing on a two‐roll mill and subsequently irradiating to different gamma radiation doses. The blends were characterized by differential scanning calorimetry, Fourier transform infrared spectroscopy, density measurement, hardness measurement, and solvent permeability analysis. The compatibility of the blends was studied by measuring the glass transition temperature and heat capacity change of the blends. The immiscibility of blends was reflected by the presence of two glass transition temperatures; however, partial miscible domains were observed due to inter diffusion of phases. Permeation data fitted best with the Maxwell's model and indicated that in CR‐EPDM blends, EPDM exists as continuous phase with CR as dispersed phase for lower CR weight fractions and phase inversion occurred in 40–60% CR region. It was observed that CR improved oil resistance of EPDM; however, the effect was prominent for blends of >20% CR content. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis of high rubber styrene–EPDM–acrylonitrile graft copolymer and its toughening effect on SAN

High rubber styrene–EPDM–acrylonitrile (AES) was prepared by the graft copolymerization of styrene (St) and acrylonitrile (AN) onto ethylene–propylene–diene terpolymer (EPDM) in n‐heptane/toluene cosolvent using benzoyl peroxide as an initiator. The effects of reaction conditions, such as reaction temperature, initiator concentration, EPDM content, the solvent component, and reaction time, on the graft copolymerization are discussed. In addition, according to the research on mechanical properties of the SAN/AES blend, a remarkable toughening effect of AES on SAN resin was found. By means of scanning electron microscopy, the toughening mechanism is proposed to be crazing initiation from rubber particles and shear deformation of SAN matrix. Uniform dispersion of rubber particles, as shown by transmission electron microscopy, is attributed to the good compatibility of SAN and AES. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 416–423, 2004     

Structure and mechanical properties of nanodispersed fibrous silicate‐reinforced ethylene–propylene–diene monomer nanocomposites

In this study, ethylene–propylene–diene monomer (EPDM)/fibrillar silicate (FS) nanocomposites were successfully prepared by mechanically blending EPDM with FS, which was modified by silane coupling agent KH570 containing methacryloxy group. The effects of silane content and modified FS on the dispersion of FS and mechanical properties of the composites were investigated. The impact of water in FS on mechanical properties of the composites was also evaluated. The results showed that modified FS could be dissociated into nanofibers dispersing evenly in the EPDM matrix by increasing substantially the loading of silane through the mechanical blending. The optimum loading level of silane coupling agent was up to 24 phr/100 phr FS. Silane KH570 could improve the dispersion of FS and strengthen nanofibers–rubber interfacial adhesion even at the loading of as high as 50 phr FS, making FS to exhibit excellent reinforcement to EPDM. Too much FS could not be completely dissociated into nanofibers, slowing down further improvement. The EPDM/FS composites exhibited the similar stress–strain behavior and obvious mechanical anisotropy with short microfiber‐reinforced rubber composites. With the increase in silane coupling agent and modified FS, the number of nanofibers increased because of the exfoliation of FS microparticles; thus, the mechanical behaviors would become more obvious. It was suggested that the free water in FS should be removed before mechanically blending EPDM with FS because it obviously affected the tensile properties of the composites. Regardless of whether FS was dried or modified, the EPDM/FS composites changed little in tensile strength after soaked in hot water. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

废旧轮胎胶粉应力诱导脱硫反应影响因素的研究

在废旧轮胎胶粉/EPDM的熔融挤出过程中,以仲丁醇为脱硫反应促进剂,研究螺杆转速和挤出反应温度对脱硫共混物凝胶质量分数(w)、凝胶分子链结构以及SBR/脱硫共混物再硫化材料物理性能的影响。结果表明:在废旧轮胎胶粉/EPDM的熔融挤出过程中,随着螺杆转速和挤出反应温度的升高,废旧轮胎胶粉颗粒所受的机械剪切应力作用增强,引起废旧轮胎胶粉中交联网络的断裂、降解或解交联反应,导致脱硫共混物w显著减小以及SBR/脱硫共混物再硫化材料中凝胶粒子尺寸明显减小;添加仲丁醇有利于脱硫反应的进行,并具有抑制交联副反应和保护脱硫产物中双键的作用,使脱硫共混物的w进一步减小;在螺杆转速为1 000 r.min-1、挤出反应温度为240℃的条件下,SBR/脱硫共混物(添加仲丁醇)再硫化材料的拉伸强度和拉断伸长率分别为19.3 MPa和567%。     

Synthesis and properties of vinyltrimethoxysilane–EPDM–styrene graft terpolymer

The graft copolymerizations of vinyltrimethoxysilane (VTMO) and styrene (St) onto ethylene–propylene–diene terpolymer (EPDM) were carried out with benzoyl peroxide (BPO) as an initiator in toluene. The effects of EPDM concentration, mole ratio of VTMO to St, reaction time, reaction temperature, and initiator concentration on the graft copolymerizations were examined. The synthesized VTMO–EPDM–St graft terpolymers (VES) were confirmed by infrared and ¹H-NMR spectroscopies. The molecular weight, thermal stability, light resistance, and weatherability of the graft terpolymer were investigated by gel permeation chromatography, thermogravimetric analysis, and Fade-o-Meter. The number-average molecular weight was 109,000. It was found that the heat resistance and light resistance as well as weatherability of VES are considerably better than those of acrylonitrile–butadiene–styrene terpolymer. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67:1345–1352, 1998     

Microwave‐induced devulcanization for poly(ethylene–propylene–diene) recycling

The production of high quantities of end‐of‐life rubbers is an environmental problem of growing importance. Because of their crosslinked nature, such rubbers cannot be easily reprocessed, and actually, they are mainly wasted or reused after a simple mechanical grinding. In this study, a microwave (MW)‐induced thermal treatment at temperatures above 300°C was proposed to obtain partial devulcanization of a poly(ethylene–propylene–diene) (EPDM) rubber filled with carbon black. The use of MWs showed to be a very fast and simple technique, which allowed the production of a treated rubber with a relatively low degree of crosslinking, a slight revulcanization ability, and suitability for reuse in conjunction with virgin rubber. Preliminary mechanical characterization, performed on the revulcanized samples, indicated that the virgin and treated rubber were able to establish a good interface adhesion, which led to performances better than those of similar materials where the recycled part was made of ground untreated EPDM. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation and characterization of acrylonitrile–styrene–methylmethacrylate terpolymer as a compatibilizer for rubber blends

Acrylonitrile‐co‐styrene‐co‐methylmethacrylate (AN‐S‐MMA) terpolymer was prepared by bulk and emulsifier‐free emulsion polymerization techniques. The bulk and emulsion terpolymers were characterized by means of Fourierr transform infrared spectroscopy, ¹³C nuclear magnetic resonance (NMR) spectroscopy, gel permeation chromatography, thermal gravimetric analysis, and elemental analysis. The kinetics of the terpolymerization were studied. The terpolymers were then incorporated into butadiene—acrylonitrile rubber (NBR)/ethylene propylene diene monomer rubber (EPDM) blends and into chloroprene rubber (CR)/EPDM blend. The terpolymers were then tested for potential as compatibilizers by using scanning electron microscopy and differential scanning calorimetry. The terpolymers improved the compatibility of CR/EPDM and NBR/EPDM blends. The physicomechanical properties of CR/EPDM and NBR/EPDM blend vulcanizates revealed that the incorporation of terpolymers was advantageous, since they resulted in blend vulcanizates with higher 100% moduli and with more thermally stable mechanical properties than the individual rubbers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3143–3153, 2003     

Preparation and characterization of composites: Ethylene–propylene–diene terpolymer‐graft‐maleic anhydride/CaCO3

In this paper, a new method was applied to form crosslinking networks in the ethylene–propylene–diene terpolymer (EPDM) matrix with calcium carbonate(CaCO₃) particles, which were chemically treated by maleic anhydride (MAH). The tensile test showed that the tensile strength and the elongation at break of the composites were improved significantly, and when the content of CaCO₃ was about 20 wt % in the composites, the maximum tensile properties were achieved. The results of swell and solution text showed that the composites had evident crosslinking structure. The results of attenuated transmission reflectance‐Fourier transform infrared (ATR‐FTIR) spectrum proved that the Acid‐Base reaction between CaCO₃ and MAH had happened. SEM micrographs showed that the interfacial adhesion between CaCO₃ and copolymer was well. The thermogravimetric analysis curves showed that the composites had a new change in mass between 655 and 700°C, which might be the decomposition temperature of calcium maleicate. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1810–1815, 2006