Synthesis and photopolymerization of ethylene glycol 3‐morpholine‐propionate methacrylate for potential dental composite application

2,2‐Bis[4‐(2‐hydroxy‐3‐methacryloxypropoxy) phenyl]‐propane (bis‐GMA), triethylene glycol dimethylacrylate (TEGDMA), camphorquinone (CQ), ethyl‐4‐dimethylaminobenzoate (EDMAB), or 2‐(dimethylamine)ethyl methacrylate (DMEM) were composed of the modern dental composite system and acted as resin, diluent, photoinitiator, and coinitiator, respectively. In this study, ethylene glycol 3‐morpholine‐propionate methacrylate (EGMPM) was synthesized via Michael addition reaction to replace both the TEGDMA as a diluent and the nonpolymerizable amine EDMAB as a coinitiator. Mixtures of bis‐GMA/TEGDMA/CQ/EGMPM and bis‐GMA/TEGDMA/CQ/DMEM were found to have almost the same rate of polymerization and reach final double bond conversion at 58%, slightly lower than that of the bis‐GMA/TEGDMA/CQ/EDMAB (63%) and bis‐GMA/EGMPM/CQ (60%) under comparable visible light irradiation conditions. In addition, the results of dynamic mechanical analysis showed that all of the four samples had approximately the same modulus and the glass transition temperature. The water sorption and solubility of bis‐GMA/TEGDMA/CQ with different amines (EDMAB, DMEM, and EGMPM) had almost the same value except that the water sorption of bis‐GMA/EGMPM/CQ was out of the range of the ISO 4049 (2000) standards. The results indicated that EGMPM was potentially a coinitiator for dental composite, because there are no significant differences in photopolymerization characteristic and physical properties when compared with traditional system (bis‐GMA/TEGDMA/CQ/EDMAB). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4589–4594, 2006     

Photopolymerization of methyl methacrylate by 2,2′‐dithiodiethanol: Effect of reaction conditions

The photopolymerization of methyl methacrylate (MMA) through the use of a novel disulphide, 2,2′‐dithiodiethanol (DDE), was studied. This photoinitiator is of special interest because of its possible use in the synthesis of polyurethane macrophotoinitiator. The photopolymerization was carried out in the Heber multilamp photochemical reactor (COMPACT‐LP‐MP88) at 254 nm. The effects of reaction conditions on the polymerization of MMA were studied. It was observed that the percentage conversion and molecular weight increased with the increases of monomer concentration and reaction time. However, for the initiator to monomer molar ratio, there was a critical molar ratio for maximum conversion. The results suggested the living radical nature of the photoinitiator, which was further investigated by the preparation of block copolymer with acrylonitrile. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1601–1606, 2006     

Methylmethacrylate polymerization photoinitiated by 1‐(bromoacetyl)pyrene

The photopolymerization of methylmethacrylate induced by pyrene, 1‐acetylpyrene (AP), and 1‐(bromoacetyl)pyrene (BP) has been investigated. Under all conditions employed, pyrene was completely ineffective. Introduction of a carbonyl and a bromo group in pyrene enhanced the polymerization efficiencies. Efficiency of AP as photoinitiator was very low; however, BP was proved to be a good photoinitiator. The polymerization with BP follows first‐order kinetics with respect to monomer conversion, with a shorter induction period as compared with that of AP. The value of the initiator exponent (0.5) and the linear dependence of reciprocal average degree of polymerization on the square root of the initiator concentration suggest radical polymerization with bimolecular termination. IR and NMR spectra showed the atactic nature of polymethylmethacrylate. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 920–926, 2006     

Synthesis and properties of photocross‐linked polymers of epoxidized linseed oil with different reactive diluents

Cross‐linked polymers were obtained by photopolymerization of epoxidized linseed oil with different reactive diluents (3,4‐epoxycyclohexylmethyl‐3,4‐epoxycyclohexane carboxylate, 1,4‐cyclohexane dimethanol diglycidyl ether, bisphenol A diglycidyl ether, trimethylolpropane triglycidyl ether, and bis[4‐(glycidyloxy)phenyl]methane) using the mixture of triarylsulfonium hexafluoroantimonates as photoinitiator. The kinetic of photocross‐linking reactions of compositions with different concentrations of reactive diluents was investigated. The 69%–91% conversion of epoxy groups of the compositions containing reactive diluents was reached. The mechanical properties, thermal stability, and swelling in polar and nonpolar solvents of the photocross‐linked polymers were studied. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Copolymers of acrylic acid with N‐vinylpyrrolidinone and 2‐hydroxyethyl methacrylate as pH‐responsive hydrogels synthesized through a photoinitiator‐free photopolymerization technique

pH‐sensitive hydrogels for biomedical applications were synthesized using a photoinitiator‐free technique involving the initiation of photopolymerization by donor/acceptor pairs. The differential photocalorimetric technique indicated a high polymerization rate for the N‐vinylpyrrolidinone (NVP, donor)/acrylic acid (AA, acceptor) pair at a 1:1 molar ratio. However, photopolymerization of larger quantities of these monomers (1:1 molar ratio) produced a water‐soluble polymer. Nevertheless, an anionic hydrogel was successfully formed when a small quantity of 2‐hydroxyethyl methacrylate (HEMA) was included in the NVP/AA formulation. A mixture of HEMA and AA, although both are classified as acceptors, photopolymerized to produce a copolymer which functioned as an anionic hydrogel. The swelling and drug release of these hydrogels were investigated in acidic, neutral and basic pH environments. Their biocompatibility with HaCaT human epidermal keratinocyte cells was tested and a positive cell growth as evidenced by the 3‐[4,5‐dimethylthiazol‐2‐yl]‐2,5‐diphenyl tetrazolium bromide (MTT) cell proliferation assay indicated that these hydrogels have no toxic effect on HaCaT. Copyright © 2006 Society of Chemical Industry     

A water‐soluble supramolecular‐structured photoinitiator between methylated β‐cyclodextrin and 2,2‐dimethoxy‐2‐phenylacetophenone

A water‐soluble supramolecular‐structured photoinitiator (SSPI) was synthesized by supramolecular self‐assembling between methylated β‐cyclodextrin (MβCD) and hydrophobic 2,2‐dimethoxy‐2‐phenylacetophenone (DMPA). The structure of SSPI was characterized by X‐ray diffraction, FTIR, ¹H NMR, UV–vis, and fluorescence spectra. The results indicated that MβCD and DMPA had formed 1 : 1 inclusion complex in methanol solution. The binding constant (K) for the complex was 7.51 × 10²M^?1. SSPI could be dissolved in water easily and its water‐solubility was 15.3 g/100 mL. SSPI was the more efficient photoinitiator than DMPA for the photopolymerization of acrylamide (AM) in homogeneous aqueous system. The conversion for photopolymerization of trimethylolpropane triacrylate system initiated by SSPI was similar to that initiated by DMPA. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

A (Triphenylphosphine)Silver (I) Complex as a New Performance Additive in Free‐Radical Photopolymerization under Air

Unusual photochemical properties of an Ag(I)‐derived complex, i.e., bis[(µ‐chloro)bis(triphenylphosphine)silver (I)] ([Ag](PPh₃)) are demonstrated when used in free‐radical photopolymerization reactions: i) [Ag](PPh₃) can act as an innovative photoinitiating system when associated with a commercial type I photoinitiator 2,2‐dimethoxy‐2‐phenylacetophenone to overcome the oxygen inhibition effect during the free‐radical photopolymerization of acrylate monomers, thus accelerating the kinetics of polymerization under air; ii) silver‐based nanoparticles can be in situ generated under air, thus leading to new antibacterial coatings which prevent the growth of Escherichia coli and Staphylococcus aureus after few hours of incubation.     

Monomer conversion in a light‐cured dental resin containing 1‐phenyl‐1,2‐ propanedione photosensitizer

The efficiency of 1‐phenyl‐1,2‐propanedione (PPD) photosensitizer for the photopolymerization of a dental resin based on 2,2‐bis[4‐(2‐hydroxy‐3‐methacryloxyprop‐1‐oxy)phenyl]propane/triethylene glycol dimethacrylate was assessed. Experimental formulations containing PPD or/and camphorquinone (CQ) in combination with dimethylaminoethyl methacrylate (DMAEMA), ethyl‐4‐dimethylaminobenzoate (EDMAB), 4‐(N,N‐dimethylamino)phenethyl alcohol (DMPOH) and N,N‐3,5‐tetramethylaniline (TMA) at different concentrations were studied. The photopolymerization was carried out by means of a commercial light‐emitting diode (LED) curing unit. Near‐infrared spectroscopy was used to follow the consumption of double bonds versus irradiation time. No significant differences in the conversion values among formulations prepared with PPD in combination with DMAEMA, DMPOH and TMA were found. In contrast, the conversion was markedly increased by the presence of EDMAB. At low concentrations of photosensitizer, when used in combination with DMAEMA and EDMAB, PPD resulted in a final conversion equivalent to CQ. However, when DMPOH and TMA were used, PPD was found to be less efficient than CQ. In addition, at high photoinitiator concentration, the effectiveness of PPD was less than that of CQ independently of the co‐initiator used. The replacement of some CQ by an equivalent amount of PPD resulted in similar final monomer conversion as formulations having the same amount of CQ alone. The LED light source employed emitted in the wavelength range 410–490 nm with a peak around 470 nm, whereas the maximum molar absorbance of PPD was in the UV region. However, the small overlap of the spectral distribution of the LED curing lamp and the PPD absorption spectrum was compensated by the large extinction coefficient of PPD. Copyright © 2007 Society of Chemical Industry     

Synthesis of a chiral stationary phase with poly[styrene‐b‐cellulose 2,3‐bis(3,5‐dimethylphenylcarbamate)] by surface‐initiated atom transfer radical polymerization and its chiral resolution efficiency

A chiral stationary phase (CSP) with poly[styrene‐b‐cellulose 2,3‐bis(3,5‐dimethylphenylcarbamate)] was synthesized by the surface‐initiated atom transfer radical polymerization (SI‐ATRP) of cellulose 2,3‐bis(3,5‐dimethylphenylcarbamate)‐6‐acrylate after the SI‐ATRP of styrene on the surface of silicon dioxide supports in pyridine. The successful preparation of the CSP with poly[styrene‐b‐cellulose 2,3‐bis(3,5‐dimethylphenylcarbamate)] was confirmed via Fourier transform infrared spectroscopy, field emission scanning electron microscopy, X‐ray photoelectron spectroscopy, elemental analysis, and thermal analysis. The applicability for the chiral resolution of the CSP with poly[styrene‐b‐cellulose 2,3‐bis(3,5‐diphenylcarbamate)] was evaluated with high‐performance liquid chromatography with 10 racemates under various mobile phases of hexane/alcohol, hexane/tetrahydrofuran (THF), and hexane/chloroform. The results show that the CSP with poly[styrene‐b‐cellulose 2,3‐bis(3,5‐diphenylcarbamate)] could be used in THF and chloroform as eluents. The chiral resolutions of the commercial Chiracel OD, the CSP with cellulose 2,3‐bis(3,5‐dimethylphenylcarabmate), and the CSP with poly[styrene‐b‐cellulose 2,3‐bis(3,5‐dimethylphenylcarbamate)] prepared by SI‐ATRP were examined. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Influence of the Thiol Structure on the Kinetics of Thiol‐ene Photopolymerization with Time‐Resolved Infrared Spectroscopy

Photopolymerization kinetics of difunctional thiols with alkenes were studied. Two of the thiols, trans‐1,4‐bis(mercaptomethyl)cyclohexane (CHDMT) and 1,4‐bis(mercaptomethyl)benzene (BDMT) were synthesized. The CHDMT was synthesized via a two step process using potassium thioacetate and hydrochloric acid as reagents. The BDMT was synthesized by a one step process using 1,4‐benzenedimethanebromine with thiourea and potassium hydroxide as reagents. Three types of alkenes (divinyl ether, diallyl ether, and dimethacrylate) were reacted with CHDMT, BDMT or 1,8‐octanedithiol (ODT). The photopolymerization was investigated with and without a photoinitiator. The kinetics of the thiol‐ene photopolymerization was investigated by time‐resolved infrared spectroscopy. It was proposed that the steric hindrance of the cyclohexane (CHDMT) resulted in a lower rate of photopolymerization compared to BDMT and ODT. The vinyl ether (alkene) exhibited the highest activity compared to allyl ether and acrylate which was attributed to a high electron density of the alkene. Incorporation of photoinitiator increased the reaction rate and final conversion of the system, particularly in the ODT system.

     

Cationic photopolymerization of polyfunctional 1‐propenyl ether systems

The cationic photopolymerization of trimethylolpropane tripropenyl ether (TPE), initiated by a diaryl iodonium salt, has been investigated. The influence of the presence of different alcoholic additives on the rates of photopolymerization and on the properties of the networks obtained has been studied. New 1‐propenyl ethers (trimethylolpropane dipropenyl ether (DPE) and its acetyl ester) were synthesized and employed as modifying agents in TPE photopolymerization. The thermal and dynamic‐mechanical properties of the films obtained have been investigated and are correlated with the structure of the networks and to the mechanism of the curing reaction; a microheterogeneous structure of the network was shown by dynamic‐mechanical thermal analysis. © 2001 Society of Chemical Industry     

Vibrational spectroscopic investigation of light‐induced polymerization process of epoxy resin,polytetrahydrofuran and spirobislactone

The light‐induced polymerization process of bisphenol F diglycidyl ether (BFDGE), 5,5′‐dicarboxylic‐7,7′‐dioxo‐2,2′‐spirodi(benzotetrahydrofuran) (DCSBL) and polytetrahydrofuran (pTHF‐250) was studied. 4‐[(2‐Hydroxytetradecyl)oxy]phenyl‐phenyliodoniumhexafluoroantimonate, camphorquinone and ethyl 4‐dimethylaminobenzoate were used as a photoinitiator system. The polymerization process was induced by light and monitored using Fourier transform infrared spectroscopy. A novel combination‐initiation polymerization process was proposed: first, cationic copolymerization of BFDGE and pTHF‐250 was initiated by the photoinitiator system and heat was released by this polymerization; then, copolymerization of BFDGE and DCSBL was induced by that heat while pTHF‐250 served as an anionic initiator. Copyright © 2007 Society of Chemical Industry     

A study of localized curing of glass‐filled composites using microhardness measurements

Extent of cure of hybrid composite systems is examined by conducting hardness measurements at different stages of the photopolymerization reaction and obtaining kinetic parameters that matched the experimental data. The materials are commercial dental composites based on bis[4‐(2‐hydroxy‐3‐methacryloyloxypropoxy)phenyl]propane resins with different photoinitiator concentrations as well as filler particle sizes and combinations. Samples (five per group) were made using nylon molds (2.5 × 5 mm) of the tested composites. The samples were light cured with a constant‐power light source for durations up to 20 s. After curing, all samples underwent Vicker's hardness testing of top and bottom surfaces. While there are significant differences in the polymerization behavior between the top and bottom locations for the tested composites, the corresponding growth exponent n, a kinetic parameter in the kinetic theory, is very close in all cases. For the tested materials the coefficient factor k is much lower for the bottom surfaces compared with the top surfaces. This reduction in the value of k is more severe for the material with a higher concentration of the photoinitiator as well as a higher percentage of glass filler particles in the wavelength range affecting the photopolymerization. It is argued that a relationship between k and the irradiation intensity can be used to quantify the decay of irradiated light with its penetration into the composites. The comparisons can be used to draw preliminary conclusions on the parameters controlling the effective depth of cure in a hybrid composite. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 426–431, 2005     

Forgotten monomers: access to α‐modified N‐vinylpyrrolidone polymers via C‐alkylation

Alkylation of N‐vinylpyrrolidone using lithium diisopropylamide and bis(2‐bromoethyl) ether was carried out to obtain 3‐(2‐(2‐bromoethoxy)ethyl)‐1‐vinyl‐2‐pyrrolidone ( 2 ). The derivative 2 represents a versatile starting molecule for further modification via nucleophilic displacement yielding, for example, the bicyclic 2‐vinyl‐8‐oxa‐2‐azaspiro[4.5]decan‐1‐one ( 4 ) or the ammonium salt 3‐diethoxy‐N,N′‐((dimethylbenzyl)ammonium bromide)‐1‐vinyl‐2‐pyrrolidone ( 10 ). Via free radical polymerization of 4 and 10 , the corresponding homopolymers were obtained. Copolymerization of 4 and 10 with N,N′‐diethylacrylamide yielded water‐soluble materials. The thermosensitive solubility of copolymers poly[(2‐vinyl‐8‐oxa‐2‐azaspiro[4.5]decan‐1‐one)‐co‐(N,N′‐diethylacrylamide)] and poly[(3‐diethoxy‐N,N′‐((dimethylbenzyl)ammonium bromide)‐1‐vinyl‐2‐pyrrolidone)‐co‐(N‐vinylpyrrolidone)] in water was investigated. © 2015 Society of Chemical Industry     

ESR and kinetic study of a novel polymerizable photoinitiator comprising the structure of N‐phenylmaleimide and benzophenone for photopolymerization

A novel polymerizable photoinitiator, 4‐[(4‐maleimido)phenoxy]benzophenone (MPBP) comprising the structure of N‐phenylmaleimide and benzophenone was used for the photopolymerization with N,N‐dimethylaminoethyl methacrylate (DMAEMA) as coinitiator. The ESR spectrum of this photoredox system was studied and compared with BP/DMAEMA; the results showed the same signals of them and verified that N‐phenylmaleimide does not generate radicals. The kinetics for photopolymerization of methyl methacrylate (MMA) using such system was studied by dilatometer. It was found that the polymerization rate was proportional to the 0.3172th power of the MPBP concentration, the 0.7669th power and the 0.1765th power of MMA concentration and DMAEMA concentration respectively; the overall apparent activation energy obtained was 31.88 kJ/mol. The polymerization kinetics of 1,6‐hexanediol diacrylate (HDDA) initiated by such system was studied by photo‐DSC. It showed that the increase in the MPBP concentration, light intensity, and temperature leads to increased polymerization rate and final conversion. The apparent activation energy was 11.25 kJ/mol. This polymerizable photoredox system was significantly favorable for reducing the migration of active species but owning high efficiency. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2347–2354, 2006     

Preparation and antidehydration of interpenetrating polymer network hydrogels based on 2‐hydroxyethyl methacrylate and N‐vinyl‐2‐pyrrolidone

This work reports the preparation of 2‐hydroxyethyl methacrylate (HEMA)/N‐vinyl‐2‐pyrrolidone (NVP) interpenetrating polymer network (IPN) hydrogels by UV‐initiated polymerization in the presence of free radical photoinitiator Darocur 1173 and cationic photoinitiator 4,4′‐dimethyl diphenyl iodonium hexafluorophosphate. The polymerization mechanism was investigated by the formation of gel network. The structure and morphology of the HEMA/NVP IPN hydrogels were characterized by fourier transform infrared spectroscopy (FTIR) and scanning electron microscope (SEM). The results showed that the IPN gels exhibited homogeneous morphology. The dehydration rates of HEMA/NVP IPN hydrogels were examined by the gravimetric method. The results revealed that the hydrogels had a significant improvement of antidehydration ability in comparison with poly(2‐hydroxyethyl methacrylate)(PHEMA) hydrogel embedded physically with poly(N‐vinyl‐2‐pyrrolidone)(PVP). © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Organosoluble and light‐colored fluorinated polyimides derived from 5,5′‐bis[4‐(4‐amino‐2‐trifluoromethylphenoxy) phenyl]‐4,7‐methanohexahydroindan

A novel bis(ether amine) monomer, 5,5′‐bis[4‐(4‐amino‐2‐trifluoromethylphenoxy)phenyl]‐4,7‐methanohexahydroindan ( 2 ), was synthesized through the nucleophilic aromatic substitution reaction of 5,5′‐bis‐(4‐hydroxyphenyl)‐4,7‐methanohexahydroindan with 2‐chloro‐5‐nitrobenzotrifluoride to yield the intermediate dinitro compound, followed by catalytic reduction with hydrazine and Pd/C. A series of polyimides were synthesized from 2 and various aromatic dianhydrides using a standard two‐stage process with chemical or thermal imidization of poly(amic acid). All of these polymer films were soluble in amide‐type solvents above 10% w/v, had tensile strengths of 97–117 MPa, and the 10% weight loss temperature was above 464 °C with their residues exceeding 46% at 800 °C in nitrogen. Compared with the non‐fluorinated polyimides, the fluorinated series were observed to have lower dielectric constants (2.92–3.28 at 1 MHz) and lower moisture absorptions (0.15–0.43 wt%) as well as lower color intensity and better solubility. Copyright © 2006 Society of Chemical Industry     

Effect of the reaction conditions on the photopolymerization of methyl methacrylate by diethyl dithiocarbamato‐(1,2)‐propane diol

The photopolymerization of methyl methacrylate (MMA) through the use of diethyl dithiocarbamato‐(1,2)‐propane diol (DCPD) was studied. The photoinitiator was synthesized from 3‐chloro‐1,2‐propane diol and sodium diethyl dithiocarbamate in a solvent mixture of acetone and anhydrous ethanol. The photopolymerization was carried out in a Heber multilamp photochemical reactor (COMPACT‐LP‐MP88) (Heber Scientific, Chennai, India) at 254 nm. The effects of the reaction conditions on the polymerization of MMA were studied. The conversion and molecular weight increased with an increase in the monomer concentration and reaction time. However, for the DCPD‐to‐MMA molar ratio, a critical value was found for maximum conversion. The results suggested the living radical nature of the photoinitiator, which was further investigated by the preparation of a block copolymer with styrene. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2320–2328, 2005     

Development of low‐shrinkage composites based on novel crosslinking vinylcyclopropanes

Polymerization shrinkage of methacrylate‐based dental composites remains a major concern in restorative dentistry. Cyclic monomers that undergo ring‐opening polymerization are known to exhibit reduced polymerization shrinkage compared to methacrylates. In this article, the synthesis of four crosslinking 1,1‐disubstituted 2‐vinylcyclopropanes bearing rigid spacers is described. These monomers were synthesized by esterification of 1‐ethoxycarbonyl‐2‐vinylcyclopropane‐1‐carboxylic acid with the corresponding diols. The photopolymerization kinetics of these monomers was investigated by photo‐differential scanning calorimeter using bis(4‐methoxybenzoyl)diethylgermane as the photoinitiator. The synthesized vinylcyclopropanes (VCPs) were shown to be more reactive than the frequently used reactive diluent triethylene glycol dimethacrylate. Composites based on these VCPs showed good mechanical properties and exhibited a significantly reduced volumetric shrinkage and shrinkage stress compared to a corresponding dimethacrylate‐based restorative material. This work highlights the excellent potential of VCPs as alternatives to methacrylates in the development of low‐shrinkage dental composites. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45577.     

Gold(I)‐Catalyzed Tandem Alkoxylation/Lactonization of γ‐Hydroxy‐α,β‐Acetylenic Esters

The formation of 4‐alkoxy‐2(5H)‐furanones was achieved via tandem alkoxylation/lactonization of γ‐hydroxy‐α,β‐acetylenic esters catalyzed by 2 mol% of [2,6‐bis(diisopropylphenyl)imidazol‐2‐ylidine]gold bis(trifluoromethanesulfonyl)imidate [Au(IPr)(NTf₂)]. The economic and simple procedure was applied to a series of various secondary propargylic alcohols allowing for yields of desired product of up to 95%. In addition, tertiary propargylic alcohols bearing mostly cyclic substituents were converted into the corresponding spiro derivatives. Both primary and secondary alcohols reacted with propargylic alcohols at moderate temperatures (65–80 °C) in either neat reactions or using 1,2‐dichloroethane as a reaction medium allowing for yields of 23–95%. In contrast to [Au(IPr)(NTf₂)], reactions with cationic complexes such as [2,6‐bis(diisopropylphenyl)imidazol‐2‐ylidine](acetonitrile)gold tetrafluoroborate [Au(IPr)(CH₃CN)][BF₄] or (μ‐hydroxy)bis{[2,6‐bis(diisopropylphenyl)imidazol‐2‐ylidine]gold} tetrafluoroborate or bis(trifluoromethanesulfonyl)imidate – [{Au(IPr)}₂(μ‐OH)][X] (X=BF₄, NTf₂) – mostly stop after the alkoxylation. Analysis of the intermediate proved the exclusive formation of the E‐isomer which allows for the subsequent lactonization.