Preparation of Ag nanoparticles in the presence of low generational poly(ester‐amine) dendrimers

Stable Ag nanoparticles of 10–20 nm were prepared by reduction of AgNO₃ with NaBH₄ in water solution in the presence of low generational hydroxyl‐ terminated poly(ester‐amine) dendrimer G1.0 (OH)₁₆ and amino‐terminated poly(ester‐amine) dendrimer G1.5 (NH₂)₈ by optimizing preparation conditions. UV–vis absorption spectra and transmission electron microscopy were adopted to characterize absorption properties of Ag⁺/dendrimer complex, Ag/dendrimer nanocomposite aqueous solutions, and the morphology of the formed Ag nanoparticles, respectively. The results showed that the size of the Ag particles increased with Ag⁺/dendrimer molar ratio, and the size of Ag nanoparticles in Ag/G1.0 (OH)₁₆ system was larger than that of Ag nanoparticles in Ag/G1.5 (NH₂)₈ system, while the polydispersities of two systems were similar. Moreover, the Ag/G1.5 (NH₂)₈ nanocomposite system was more stable than the Ag/G1.0 (OH)₁₆ one. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 422–426, 2007     

Effects of amino‐functionalized carbon nanotubes on the properties of amine‐terminated butadiene–acrylonitrile rubber‐toughened epoxy resins

Amino‐functionalized multiwalled carbon nanotubes (MWCNT‐NH₂s) as nanofillers were incorporated into diglycidyl ether of bisphenol A (DGEBA) toughened with amine‐terminated butadiene–acrylonitrile (ATBN). The curing kinetics, glass‐transition temperature (T_g), thermal stability, mechanical properties, and morphology of DGEBA/ATBN/MWCNT‐NH₂ nanocomposites were investigated by differential scanning calorimetry (DSC), thermogravimetric analysis, a universal test machine, and scanning electron microscopy. DSC dynamic kinetic studies showed that the addition of MWCNT‐NH₂s accelerated the curing reaction of the ATBN‐toughened epoxy resin. DSC results revealed that the T_g of the rubber‐toughened epoxy nanocomposites decreased nearly 10°C with 2 wt % MWCNT‐NH₂s. The thermogravimetric results show that the addition of MWCNT‐NH₂s enhanced the thermal stability of the ATBN‐toughened epoxy resin. The tensile strength, flexural strength, and flexural modulus of the DGEBA/ATBN/MWCNT‐NH₂ nanocomposites increased increasing MWCNT‐NH₂ contents, whereas the addition of the MWCNT‐NH₂s slightly decreased the elongation at break of the rubber‐toughened epoxy. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40472.     

端氨基树枝状大分子/环氧树脂体系固化动力学的FTIR研究

用傅立叶变换红外光谱(FTIR)法研究了双酚A二缩水甘油醚环氧树脂(GEBA)用低代端氨基聚(酯-胺)树枝状大分子G1.0(NH2)3、G1.5(NH2)8和聚(胺-酰胺)树枝状大分子PAMAM1.0(NH2)4作为固化剂的等温固化动力学,得到了不同温度下转化率与固化时间及反应速率与固化时间的关系.与小分子固化剂相比,端氨基树枝状大分子作固化剂时环氧基转化率在反应开始时增长得更快,较高代树枝状大分子在高温下固化环氧树脂时尤其如此.在相同温度和时间下,PAMAM1.0(NH2)4/DGEBA、G1.0(NH2)3/DGEBA、G1.5(NH2)8/DGEBA体系的转化率依次增大.进一步估算了3个体系在一定转化率下的固化反应表观活化能.在相同转化率时,用G1.5(NH2)8、PAMAM1.0(NH2)4、G1.0(NH2)3作固化剂的体系表观活化能依次减小.     

Advanced isoconversional cure kinetic analysis of epoxy/poly(furfuryl alcohol) bio‐resin system

Furfuryl alcohol as a biomass‐derived monomer was used for synthesizing poly(furfuryl alcohol). A diglycidyl ether of bisphenol A (DGEBA) epoxy resin along with 3% and 15% by weight of the poly(furfuryl alcohol) was cured using an aliphatic amine hardener. The cure kinetics of the DGEBA/poly(furfuryl alcohol)/amine systems were investigated by nonisothermal differential scanning calorimetry. The kinetic triplets [E_α, A_α, and f(α)] were computed by using an integral isoconversional method. Based on the E_α‐dependency results a single‐step autocatalytic model was suggested for the reactions mechanism, however, the A_α‐dependency and f(α) analysis did not confirm the suggested model. Detailed kinetics analysis revealed that the cure reaction mechanism of the DGEBA did not change due to the presence of the poly(furfuryl alcohol) in the degree of conversion range < 0.75, nevertheless, it dramatically changed in the degree of conversion range > 0.75 due to the presence of 15 wt % poly(furfuryl alcohol). © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45432.     

Nonisothermal cure of bisphenol epoxy resin with a nonlinear aliphatic polyamine hardener

The amino terminated polypropylenimine dendrimer (DAB‐dendri‐(NH₂)₄) was employed as a new nonlinear aliphatic curing agent for diglycidyl ether of bisphenol A (DGEBA). Nonisothermal curing reaction kinetics of DGEBA/DAB was investigated with a differential scanning calorimeter (DSC). The apparent reaction activation energy E_a is about 56.7 kJ/mol determined using the Kissinger equation, and a two‐parameter (m, n) autocatalytic model ([icirc]Sesták–Berggren equation) was confirmed to be able to well simulate the reaction kinetics in the light of the Málek method. In addition, the relation between reaction activation energy E_a and curing degree α was obtained by applying model‐free isoconversional analysis with the Kissinger‐Akahira‐Sunose (KAS) method. As α increases, E_a reduced quickly from >80 kJ/mol to ≈60 kJ/mol up to a ≈ 15%, then decreased slowly to 55 kJ/mol till a ～ 75%, and finally dropped to 44 kJ/mol at full conversion. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Tertiary‐amine‐free,non‐planar,sulfone‐containing,tetrafunctional epoxy and its application as a high temperature matrix

Non‐amine‐derived tetrafunctional epoxies have several advantages over the amine‐derived N,N,N′,N′‐tetraglycidyl‐4,4′‐diaminodiphenyl methane (TGDDM) in high temperature applications. Although two non‐amine‐derived tetrafunctional epoxies were developed in our laboratory, further improvements in toughness using less loading amount is still desirable. Thus, a tertiary‐amine‐free, non‐planar and triphenylmethane‐containing tetrafunctional epoxy (STFE) with a sulfone spacer was synthesized. When it was mixed with diglycidyl ether of bisphenol A (DGEBA) and cured with 4,4′‐diaminodiphenylsulfone (DDS), both thermal and mechanical performances outperformed TGDDM. Moreover, STFE modified system shows the highest toughness (35.7 kJ m^–2) among three amine‐free and triphenylmethane‐containing epoxies at merely 5 wt% loading. Molecular simulation and thermomechanical analysis results suggest that the improved mechanical properties could be related to the geometry of the molecule and larger free volume. Despite a marginal drop in T_g, the thermal degradation temperature is better than that of TGDDM/DDS. In addition, the moisture resistance of STFE/DGEBA/DDS is much better than that of TGDDM/DDS. Thus, STFE modified DGEBA could be a potential replacement for TGDDM in some high temperature applications. © 2020 Society of Chemical Industry     

Intercalation and exfoliation of clay nanoplatelets in epoxy‐based nanocomposites: TEM and XRD observations

Diglycidyl ether of bisphenol A (DGEBA) and diglycidyl ether of bisphenol F (DGEBF) reinforced with organo‐montmorillonite clay nanoplatelets were investigated using anhydride‐ and amine‐curing agents. The sonication technique was used to process epoxy/clay nanocomposites. The basal spacing of clay nanoplatelets was observed by wide‐angle X‐ray scattering (WAXS), small‐angle X‐ray scattering (SAXS) techniques, and transmission electron microscopy. It was found that the basal spacing of clay nanoplatelets in epoxy matrix was expanded after mixing with either DGEBA/DGEBF or methyltetrahydrophthalic‐anhydride (MTHPA) curing agent. The sonication technique provided larger d‐spacing of clay nanoplatelets. Because of the different curing temperatures, MTHPA‐cured epoxy/clay nanocomposites produced more expanded d‐spacing of clay nanoplatelets modified with methyl, tallow, bis(2‐hydroxyethyl) quaternary ammonium (MT2EtOH) than triethylenetetramine‐cured nanocomposites. Depending on the selection of curing agent and organic modification for clay nanoplatelets, the d‐spacing was expanded to be up to 8.72 nm. POLYM. ENG. SCI., 46:452–463, 2006. © 2006 Society of Plastics Engineers     

Kinetics and thermal properties of epoxy resin cured with Ni(II)‐tris‐(O‐pheneylendiamine) bromide

Diglycidyl ether of bisphenol A (DGEBA) is cured with a nickel complex of O‐phenylendiamine (OPD) as a ligand. The structure of the synthesized curing agent is confirmed through IR and elemental analysis. The curing kinetics of DGEBA/Ni(OPD)₃Br₂ system is studied by the dynamic DSC and isothermal FTIR techniques. In all cases, we have observed at least two exothermic peaks during DSC traces up to 350°C. Dynamic activation energies are calculated by using the two isoconversional, Kissinger and Ozawa, methods applied to peak maximum. A two‐parameter (m, n) autocatalytic model (Sestak–Berggren equation) is found to be the most adequate model to describe the cure kinetics of the observed thermal events. Isothermal kinetic parameters are estimated using the Horie model. The onset decomposition temperature and char yield (at 700°C) of the crosslinked material were 290°C and 27%, respectively. The activation energy of the solid‐state thermal degradation process is evaluated by Ozawa approach, resulting in 95–138 kJ/mol on a range of 2–20% decomposition conversion. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1257–1265, 2006     

Preparation and properties of high‐performance polysilsesquioxanes/bismaleimide‐triazine hybrids

A novel kind of high‐performance hybrids (coded as POSS‐NH₂/BT) with significantly decreased curing temperature, lowered dielectric constant and loss, and improved thermal resistance were developed, which were prepared by copolymerizing bismaleimide with cage octa(aminopropylsilsesquioxane) (POSS‐NH₂) to produce POSS‐containing maleimide, and then co‐reacted with 2,2′‐bis(4‐cyanatophenyl) isopropylidene. The curing behavior and typical properties of cured POSS‐NH₂/BT were systematically investigated. Results show that POSS‐NH₂/BT hybrids have lower curing temperatures than BT resin because of the additional reactions between  OCN and amine groups. Compared with BT resin, all hybrids show improved dielectric properties. Specifically, hybrids have slightly decreased dielectric constants and similar dependence of dielectric constant on frequency over the whole frequency from 10 to 10⁶ Hz; more interestingly, the dielectric loss of hybrids is only 25% of that of BT resin at the frequency lower than 10⁵ Hz, whereas all hybrids and BT resin have almost equal dielectric loss when the frequency is higher than 10⁵ Hz. In addition, POSS‐NH₂/BT hybrids also show good thermal and thermo‐oxidative stability compared with BT resin. All these differences in macroproperties are attributed to the difference in chemical structure between POSS‐NH₂/BT hybrids and BT resin. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and spectroelectrochemistry of dithieno(3,2‐b:2′,3′‐d)pyrrole derivatives

New π‐conjugated polymers containing dithieno(3,2‐b:2′,3′‐d)pyrrole (DTP) were successfully synthesized via electropolymerization. The effect of structural differences on the electrochemical and optoelectronic properties of the 4‐[4H‐dithieno(3,2‐b:2′,3′‐d)pyrrol‐4‐yl]aniline (DTP–aryl–NH₂), 10‐[4H‐dithiyeno(3,2‐b:2′,3′‐d)pirol‐4‐il]dekan‐1‐amine (DTP–alkyl–NH₂), and 1,10‐bis[4H‐dithieno(3,2‐b:2′,3′‐d)pyrrol‐4‐yl] decane (DTP–alkyl–DTP) were investigated. The corresponding polymers were characterized by cyclic voltammetry, NMR (¹H‐NMR and ¹³C‐NMR), and ultraviolet–visible spectroscopy. Changes in the electronic nature of the functional groups led to variations in the electrochemical properties of the π‐conjugated systems. The electroactive polymer films revealed redox couples and exhibited electrochromic behavior. The replacement of the DTP–alkyl–DTP unit with DTP–aryl–NH₂ and DTP–alkyl–NH₂ resulted in a lower oxidation potential. Both the poly(10‐(4H‐Dithiyeno[3,2‐b:2′,3′‐d]pirol‐4‐il)dekan‐1‐amin) (poly(DTP–alkyl–NH₂)) and poly(1,10‐bis(4H‐dithieno[3,2‐b:2′,3′‐d]pyrrol‐4‐yl) decane) (poly(DTP–alkyl–DTP)) films showed multicolor electrochromism and also fast switching times (<1 s) in the visible and near infrared regions. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40701.     

High‐performance thermosetting films based on an amino‐functionalized poly(ether sulfone)

We have developed a sequence‐dependent synthesis of the amino‐functionalized poly(ether sulfone) P2 . The amino groups of P2 act as reactive sites toward epoxy resins. After curing P2 with diglycidyl ether of bisphenol A (DGEBA) and cresol novolac epoxy (CNE), we obtained the flexible, light‐yellow, transparent, epoxy thermosetting films P2 /DGEBA, and P2 /CNE, respectively, having glass transition temperatures (T_g) of 258 and 274°C, respectively. In addition, we also prepared a flexible film after condensation of the amino groups of P2 with the anhydride groups of 4,4′‐oxydiphthalic anhydride (ODPA); after imidization at 300°C for 1 h, the resulting P2 /ODPA thermosetting film possessed a value of T_g of 340°C. These three thermosetting films also exhibited flame retardancy with a UL‐94 VTM‐0 grade. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40980.     

Influence of PS‐b‐PEO diblock copolymers on the compatibility of syndiotactic polystyrene modified epoxy blends

Homogeneous solutions of syndiotactic polystyrene (sPS) in diglycidylether of bisphenol A (DGEBA), containing 2.5, 5 and 7.5 wt % of thermoplastic with or without 0.5 and 1 wt % of poly(styrene‐b‐ethylene oxide) (PS‐b‐PEO) block copolymer, were polymerized using a stoichiometric amount of an aromatic amine hardener, 4,4′‐methylene bis (3‐chloro‐2,6‐diethylaniline) (MCDEA). The dynamic‐mechanical properties and morphological changes of sPS‐(DGEBA/MCDEA) compatibilized with different amount of PS‐b‐PEO have been investigated in this paper. The addition of the block copolymer produced significant changes in the morphologies generated. The size of the dispersed spherical sPS spherulites does not change significantly, but less spherulites of sPS appeared upon network formation in the systems with compatibilizer, what means that addition of compatibilizer in this system delayed crystallization of sPS in sPS‐(DGEBA/MCDEA) systems and change phase separation mechanism from crystallization‐induced phase separation (CIPS) and reaction‐induced phase separation (RIPS) almost only to RIPS. Moreover, PS‐b‐PEO with higher molecular weight of PS block seems to be a more effective compatibilizer than one with lower molecular weight of PS block. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 479–488, 2006     

The effect of ionic interaction on the miscibility and crystallization behaviors of poly(ethylene glycol)/poly(L‐lactic acid) blends

The effect of end groups (2NH₂) of poly(ethylene glycol) (PEG) on the miscibility and crystallization behaviors of binary crystalline blends of PEG/poly(L ‐lactic acid) (PLLA) were investigated. The results of conductivity meter and dielectric analyzer (DEA) implied the existence of ions, which could be explained by the amine groups of PEG gaining the protons from the carboxylic acid groups of PLLA. The miscibility of PEG(2NH₂)/PLLA blends was the best because of the ionic interaction as compared with PEG(2OH, 1OH‐1CH₃, and 2CH₃)/PLLA blends. Since the ionic interaction formed only at the chain ends of PEG(2NH₂) and PLLA, unlike hydrogen bonds forming at various sites along the chains in the other PEG/PLLA blend systems, the folding of PLLA blended with PEG(2NH₂) was affected in a different manner. Thus the fold surface free energy played an important role on the crystallization rate of PLLA for the PEG(2NH₂)/PLLA blend system. PLLA had the least fold surface free energy and the fast crystallization rate in the PEG(2NH₂)/PLLA blend system, among all the PEG/PLLA systems studied. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation of different dendritic‐layered silicate nanocomposites

Several dendrimer–clay nanocomposites have been prepared. Firstly, the dendrimer (DE₁)/clay nanocomposite was obtained via an in situ free radical polymerization of a double bond‐ended dendrimer (DE₁), derived from Behera's amine by using 2,2′‐azobisisobutyronitrile (AIBN), as initiator, and Cloisite 30 B, as nanofiller. Further free radical in situ copolymerization processes were conducted between DE₁, methyl methacrylate (MMA), and styrene (St). Two other dendrimer/clay nanocomposites were prepared by the reaction of second generation (G₂)–36‐acid dendrimer (DE₂) and N,N′,N′,N′‐tetrakis[2‐hydroxy‐1,1‐bis(hydroxylmethyl) ethyl]‐α,α,ω,ω‐alkane‐tetracarboxamide [6]‐10‐[6] Arborols (DE₃) with montmorillonite clay (MMT). POLYM. ENG. SCI., 53:2166–2174, 2013. © 2013 Society of Plastics Engineers     

Effect of structural change of pitch on the thermal conductivity of epoxy‐based composites filled with heat‐treated pitch

Petroleum‐based pitches were used as filler materials to study the effects of heat‐treatment‐induced changes in pitch structure on the thermal conductivity of epoxy‐based composites. The heat treatment was performed in two steps: the first involved heating the pitch to 250 °C in order to remove the low‐molecular‐weight compounds from the pitch, and the second involved heating the pitch to either 430 or 450 °C. There was no significant difference in the curing behavior of the diglycidyl ether of bisphenol A (DGEBA)/pitch composites, regardless of the heat‐treatment temperature. However, the thermal conductivity of the DGEBA/pitch composites improved with increasing heat‐treatment temperature, and the epoxy composite prepared with pitch heat‐treated at 430 °C exhibited the maximum thermal conductivity. This can be attributed to structural changes in the pitch, such as the distance between adjacent planes (d‐spacing), crystallite height (L_c) and crystallite width (L_a). Although L_c of the pitch increased with increasing heat‐treatment temperature, the d‐spacings and L_a decreased. These results suggest that the heat treatment of the pitch led to a well‐stacked crystalline structure. However, compared with the pitch heat‐treated at 430 °C, that heat‐treated at 450 °C exhibited lower thermal conductivity in the DGEBA/pitch composite because of the low L_a, resulting in the loss of basal carbon as a consequence of in situ gasification, and pyrolysis of the low‐molecular‐weight compounds in the pitch. © 2013 Society of Chemical Industry     

Synthesis,characterization, and performance evaluation of PES/EDA‐functionalized TiO2 mixed matrix membranes for CO2/CH4 separation

Poor adhesion between hydrophobic polymers and hydrophilic inorganic fillers is a challenge that encumbers a high separation performance of mixed matrix membrane (MMM). In this study, Titanium(IV) oxide (TiO₂) nanoparticles were functionalized using ethylenediamine (EDA) before embedment in poly(ether sulfone) (PES) polymer matrix. MMMs were synthesized through dry phase inversion technique. Membranes morphology and nanoparticles dispersion was drastically enhanced posterior amine modification indicating an improved adhesion between the polymer and filler particles. Membranes thermal stability was likewise improved as higher degradation temperatures were perceived for PES/EDA–TiO₂ MMMs. Gas separation evaluation for pure carbon dioxide (CO₂) and methane (CH₄) gases revealed a remarkably enhanced separation performance upon amine‐grafting of TiO₂ as EDA‐TiO₂ MMMs exhibited a higher separation performance as compared to MMMs with pristine TiO₂. The highest ideal separation factor achieved was 41.52 with CO₂ permeability of 10.11 Barrer at an optimum loading of 5% wt of EDA‐TiO₂ which is threefold higher as compared to neat PES membrane and approximately twofold higher than MMMs with pristine TiO₂, respectively, at the same filler loading. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45346.     

Synthesis and characterization of stearyl‐group‐terminated dendrimers and thermosensitivity of their toluene solutions

Stearyl‐group‐terminated poly(ester amide) dendrimers [PEAD (R)₃ and PEAD (R)₈] and a poly(amino amide) dendrimer [PAMAM (R)₄] were synthesized by the amidation of three, eight, and four terminated primary amino groups in poly(ester amine) dendrimers and a poly(amino amide) dendrimer with stearyl chloride. The dendrimer structures were characterized with IR and elemental analysis. The toluene solutions of the stearyl‐group‐terminated dendrimers were thermosensitive. Not only did gels form in PEAD (R)₃–, PEAD (R)₈–, and PAMAM (R)₄–toluene solutions below 57.5, 60, and 49°C, respectively, but the content of toluene in the gels depended on the temperature, and a break existed at about 30°C. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 341–346, 2005     

Gadolinium‐conjugated FA‐PEG‐PAMAM‐COOH nanoparticles as potential tumor‐targeted circulation‐prolonged macromolecular MRI contrast agents

The aim of research is to develop potential tumor‐targeted circulation‐prolonged macromolecular magnetic resonance imaging (MRI) contrast agents without the use of low molecular gadolinium (Gd) ligands. The contrast agents were based on polymer–metal complex nanoparticles with controllable particle size to achieve the active and passive tumor‐targeted potential. In particular, poly (amidoamine) (PAMAM) dendrimer with 32 carboxylic groups was modified with folate‐conjugated poly (ethyleneglycol) amine (FA‐PEG‐NH₂, M_w: 2 k and 4 kDa). FA‐PEG‐PAMAM‐Gd macromolecular MRI contrast agents were prepared by the complex reaction between the carboxylic groups in PAMAM and GdCl₃. The structure of FA‐PEG‐PAMAM‐COOH was confirmed by nuclear magnetic resonance (¹H‐NMR), Fourier transform infrared (FTIR) spectra, and electrospray ionization mass spectra (ESI‐MS). The mass percentage content of Gd (III) in FA‐PEG‐PAMAM‐Gd was measured by inductively coupled plasma‐atomic emission spectrometer (ICP‐AES). The sizes of these nanoparticles were about 70 nm measured by transmission electron microscopy, suggestion of their passive targeting potential to tumor tissue. In comparison with clinically available small molecular Gadopentetate dimeglumine, FA‐PEG‐PAMAM‐Gd showed comparable cytotoxicity and higher relaxation rate, suggestion of their great potential as tumor‐targeted nanosized macromolecular MRI contrast agents due to the overexpressed FA receptor in human tumor cell surfaces. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Toughness and strength improvement of diglycidyl ether of bisphenol‐A by low viscosity liquid hyperbranched epoxy resin

This article reports on the use of low viscosity liquid thermosetting hyperbranched poly(trimellitic anhydride‐diethylene glycol) ester epoxy resin (HTDE) as an additive to an epoxy amine resin system. Four kinds of variety molecular weight and epoxy equivalent weight HTDE as modifiers in the diglycidyl ether of bisphenol‐A (DGEBA) amine systems are discussed in detail. It has been shown that the content and molecular weight of HTDE have important effect on the performance of the cured system, and the performance of the HTDE/DGEBA blends has been maximum with the increase of content and molecular weight or generation of HTDE. The impact strength and fracture toughness of the cured systems with 9 wt % second generation of HTDE are 58.2 kJ/m² and 3.20 MPa m^1/2, which are almost three and two times, respectively, of DGEBA performance. Furthermore, the tensile and flexural strength can be enhanced about 20%. The glass transition temperature and Vicat temperature, however, are found to decrease to some extent. The fracture surfaces are evaluated by using scanning electron microscopy, which showed that the homogeneous phase structure of the HTDE blends facilitates an enhanced interaction with the polymer matrix to achieve excellent toughness and strength enhancement of the cured systems, and the “protonema” phenomenon in SEM has been explained by in situ reinforcing and toughening mechanism and molecular simulation. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2504–2511, 2006     

Curing of epoxy resin using imide‐amines

The curing behavior of diglycidyl ether of bisphenol‐A (DGEBA) was investigated by differential scanning calorimetry, using varying molar ratios of imide‐amines and 4,4′‐diaminodiphenyl sulfone (DDS). The imide‐amines were prepared by reacting 1 mol of pyromellitic dianhydride (P) with excess (2.5 mol) of 4,4′‐diaminodiphenyl ether (E), 4,4′‐diaminodiphenyl methane (M), or 4,4′‐diaminodiphenyl sulfone (S) and designated as PE, PM, PS. Structural characterization was done using FTIR, ¹H NMR, ¹³C NMR spectroscopic techniques and elemental analysis. The mixture of imide‐amines and DDS at ratio of 0 : 1, 0.25 : 0.75, 0.5 : 0.5, 0.75 : 0.25, and 1 : 0 were used to investigate the curing behavior of DGEBA. The multiple heating rate method (5, 10, 15, and 20°C/min) was used to study the curing kinetics of epoxy resins. The peak exotherm temperature was found to be dependent on the heating rate, structure of imide‐amine, and also on the ratio of imide‐amine : DDS used. Activation energy was highest in case of epoxy cured using a mixture of DDS : imide‐amine of a ratio of 0.75 : 0.25. Thermal stability of the isothermally cured resins was also evaluated in a nitrogen atmosphere using dynamic thermogravimetry. The char yield was highest in case of resins cured using mixture of DDS : PS (0.25 : 0.75; EPS‐3), DDS : PM (0.25 : 0.75; EPM‐3), and DDS : PE (0.75 : 0.25; EPE‐1). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3502–3510, 2006