Modeling combustion of straw–bitumen pellets in a fluidized bed

Recently, straw–bitumen pellets have been proposed as an alternative fuel. In this paper, a comprehensive model for steady state combustion of straw–bitumen pellets in a bubbling fluidized bed is presented. The combustor is divided into three sectors: a dense bed zone, a splashing zone and a freeboard zone. Relevant phenomena including volatile release and segregation, char comminution and elutriation, bed particles ejection, and post-combustion above the bed have been taken into consideration. Energy equations for the splashing and freeboard zones have been established.     

海藻生物质颗粒流化床燃烧试验研究

在小型流化床试验台上研究了海藻颗粒(条浒苔与马尾藻)的流化床燃烧。海藻在流化床内的挥发分析出燃烧时间都在1 min左右。条浒苔颗粒在流化床中燃烧先进行脱水和挥发分的燃烧,接着发生焦炭燃烧,其燃烧过程符合缩核模型,炭核由外向内逐层燃烧,而灰层半径几乎不变。但马尾藻颗粒由于挥发分的大量快速释放而迅速膨胀破碎成屑。另外通过对条浒苔颗粒及不同燃烧时间后收集的焦炭颗粒剖面的SEM扫描电镜观察,发现随着燃烧的进行,颗粒内孔隙增大,微孔表面粗糙。进一步详细研究了两种海藻颗粒(条浒苔与马尾藻)在流化床内单次投料下的燃烧。随着床温的升高,条浒苔释放NO_x相对浓度增加,CO相对浓度减少。而马尾藻释放气体中SO₂与NO_x含量相对条浒苔有所增加;随着床温的升高,CO相对浓度减少。床温的升高使得床内传热速率加快,两种海藻挥发分的析出提前,燃尽时间缩短。风速、床高的升高使得两种海藻燃烧容易,燃尽时间缩短。     

Reduction of the Volatile Matter Evolution Rate from a Plastic Pellet during Bubbling Fluidized Bed Pyrolysis by Using Porous Bed Material

Rapid volatile matter evolution from high‐volatile fuels such as wastes and biomass is one of problems associated with fluidized bed incinerators and gasifiers. When volatile matter evolves rapidly in the vicinity of the fuel feed point, the mixing of volatile matter with reactant gas is poor, and therefore, unreacted volatile matter is expected to be released from the reactor. In the present work, reduction of the volatile matter evolution rate was attempted by employing porous solids as bed materials instead of nonporous sand. The effect of bed material on the onset of devolatilization was measured by use of a bench‐scale bubbling fluidized bed reactor. Volatile matter capture by the porous solids (capacitance effect) and the heat transfer rate within the bed, both of which affect volatile matter evolution rate, were also measured. Four types of porous solids, both with and without capacitance effect, were employed as the bed material. By employing porous solids without capacitance effect, the contributions of reduced heat transfer rate and capacitance effect to the delay of volatile matter evolution can be evaluated separately. For porous bed materials with a moderate capacitance effect (volatile matter capture of up to 20 %), the delay of the onset of devolatilization, which was measured by detecting the flame combustion of the volatile matter, was explained by the lower heat transfer between the fuel and bed. However, for a porous particle with high capacitance effect (volatile matter capture of 30 %), the capacitance effect also affected the delay of the onset of the flame combustion.     

Two-stage dual fluidized bed gasification: Its conception and application to biomass

The quoted two-stage dual fluidized bed gasification (T-DFBG) devises the use of a two-stage fluidized bed (TFB) to replace the single-stage bubbling fluidized bed gasifier involved in the normally encountered dual fluidized bed gasification (N-DFBG) systems. By feeding fuel into the lower stage of the TFB, this lower stage functions as a fuel gasifier similar to that in the N-DFBG so that the upper stage of the TFB works to upgrade the produced gas in the lower stage and meanwhile to suppress the possible elutriation of fuel particles fed into the freeboard of the lower-stage bed. The heat carrier particles (HCPs) circulated from the char combustor enter first the upper stage of the TFB to facilitate the gas upgrading reactions occurring therein, and the particles are in turn forwarded into the lower stage to provide endothermic heat for fuel pyrolysis and gasification reactions. Consequently, with T-DFBG it is hopeful to increase gasification efficiency and decrease tar content in the produced gas. This anticipation was corroborated through gasifying dry coffee grounds in two 5.0kg/h experimental setups configured according to the principles of T-DFBG and N-DFBG, respectively. In comparison with the N-DFBG case, the test according to T-DFBG increased, the fuel C conversion and cold gas efficiency by about 7% and decreased tar content in the produced gas by up to 25% under similar reaction conditions. Test results demonstrated also that all these upgrading effects via adopting T-DFBG were more pronounced when a Ca-based additive was blended into the fuel.     

A Practical Method to Estimate the Bed Height of a Fluidized Bed of Fine Particles

Knowledge of both dense bed expansion and freeboard solids inventory are required for the determination of bed height in fluidized beds of fine particles, e.g., Fluidized Catalytic Cracking (FCC) catalysts. A more accurate estimation of the solids inventory in the freeboard is achieved based on a modified model for the freeboard particle concentration profile. Using the experimentally determined dense bed expansion and the modified freeboard model, a more practical method with improved accuracy is provided to determine the bed height both in laboratory and industrial fluidized beds of FCC particles. The bed height in a fluidized bed can exhibit different trends as the superficial gas velocity increases, depending on the different characteristics of the dense bed expansion and solids entrainment in the freeboard. The factors that influence the bed height are discussed, showing the complexity of bed height and demonstrating that it is not realistic to determine the bed height by a generalized model that can accurately predict the dense bed expansion and freeboard solids inventory simultaneously. Moreover, a method to determine the bed height, based on axial pressure fluctuation profiles, is proposed in this study for laboratory fluidized beds, which provides improved accuracy compared to observation alone or determining the turning points in the axial pressure profiles, especially in high‐velocity fluidized beds.     

无烟煤化学链燃烧过程燃料氮转化释放特性

基于赤铁矿石载氧体,在小型单流化床反应器上,开展煤挥发分和焦炭的化学链燃烧研究,探讨挥发分氮和焦氮在化学链燃烧过程中的转化特性。研究表明:燃料氮释放的中间产物HCN和NH₃与铁矿石载氧体具有较高的化学反应亲和性,易于被载氧体氧化生成N₂和NO。淮北无烟煤挥发分氮转化过程中,NO是唯一的氮氧化物,反应器出口中间产物NH₃的释放份额略高于HCN。在煤焦化学链燃烧还原过程中,部分燃料氮释放的中间产物HCN和NH₃被铁矿石氧化导致少量NO的生成,还原过程中无N₂O的释放;较高的还原反应温度加速了NO的生成。减少进入载氧体氧化再生过程的焦炭量可减少空气反应器NO和N₂O的生成。     

HEAT TRANSFER BETWEEN HORIZONTAL TUBES AND FREEBOARD REGION OF A LOW-RANK COAL FLUIDIZED BED COMBUSTOR

Experiments are conducted to measure the heat transfer rates to air-cooled horizontal tubes of diameter 38.1mm in the freeboard region of a pilot-scale fluidized-bed combustor burning North Dakota lignite- Silica sand with diameter ranging from 883 to 973 μim is used as bed material. The tests are carried out without limestone addition and ash recycle, at average bed temperatures ranging from 698 to 1117K, freeboard temperatures of 700 to 1139 K and superficial velocities of 1.74 to 1.86 m/s. Among the existing correlations, those proposed by George and Grace (1982), and Byam et al. (1981) are found to predict the experimental results quite well and their root-mean-square deviations are found to be 15.8 and 18.4 percent respectively. @KEYWORDS: Heat transfer, Fluidized bed Coal combustor     

Surface-to-suspension heat transfer model in lean gas–solid freeboard flow

Heat transfer in dense fluidized beds have been extensively studied. However, there is not much detailed information about the mechanism of surface-to-suspension heat transfer in the freeboard region. In the present work, a newly designed heating plate was used to measure the plate-surface-to-particle-suspension heat transfer coefficients in the freeboard.The experimental unit consisted of a 30 cm i.d. fluidized bed reactor packed with fluidized catalytic particles of mean particle size 90 μm. Three types of plate orientations were used to test directional effects of surface on heat transfer rate. Height of the freeboard was 171 cm, and the superficial gas velocity was varied from 0.28 to 0.64 m/s. Local solids concentrations in the freeboard were also obtained by a nozzle-type sampling probe. Data on axial distribution of solids concentration were used to find out the solids kinematics in the freeboard region. Finally, a surface-to-suspension heat transfer model was developed to elucidate the surface to particle heat transfer mechanism in this lean phase system.The model is based on the transient gas-convective heating of single particles when sliding over the heating plate and the assumption of instantaneous attachment–detachment equilibrium between particles and the plate surface.     

Peach and apricot stone combustion in a bubbling fluidized bed

In this study, a bubbling fluidized bed combustor (BFBC) of 102 mm inside diameter and 900 mm height was used to investigate the combustion characteristics of peach and apricot stones produced as a waste from the fruit juice industry. A lignite coal was also burned in the same combustor. The combustion characteristics of the wastes were compared with that of a lignite coal that is most widely used in Turkey. On-line concentrations of O₂, CO, CO₂, SO₂, NO_X and total hydrocarbons (C_mH_n) were measured in the flue gas during combustion experiments. By changing the operating parameters (excess air ratio, fluidization velocity, and fuel feed rate), the variation of emissions of various pollutants was studied. Temperature distribution along the bed was measured with thermocouples.During the combustion tests, it was observed that the volatile matter from peach and apricot stones quickly volatilizes and mostly burn in the freeboard. The temperature profiles along the bed and the freeboard also confirmed this phenomenon. It was found that as the volatile matter of fruit stones increases, the combustion takes place more in the freeboard region.The results of this study have shown that the combustion efficiencies ranged between 98.8% and 99.1% for coal, 96.0% and 97.5% for peach stone and 93.4% and 96.3% for apricot stones. The coal has zero CO emission, but biomass fuels have very high CO emission which indicates that a secondary air addition is required for the system. SO₂ emission of the coal is around 2400–2800 mg/Nm³, whereas the biomass fuels have zero SO₂ emission. NO_X emissions are all below the limits set by the Turkish Air Quality Control Regulation of 1986 (TAQCR) for all tests. As the results of combustion of two biomass fuels are compared with each other, peach stones gave lower CO and NO_X emissions but the SO₂ emissions are a little higher than for apricot stones. These results suggest that peach and apricot stones are potential fuels that can be utilized for clean energy production in small-scale fruit juice industries by using BFBC.     

The ignition temperature of lignite char in a fluidized bed combustor

This paper summarises the experimental and modelling work carried out for the variation of bed ignition temperature of a fluidized bed combustor with the char particle diameter and the fluidizing velocity. A lignite char was used and its reactivity was represented using data from Field (1967) and Turnbull and Davidson (1984). The modelling involved solving the steady state heat balance around the fluidized bed combustor at the ignition temperature. A correlation of the total area of char ignited per unit bed mass was determined as a function of the char particle diameter and the fluidizing velocity. This correlation was used to determine the ignition temperature of the fluidized bed combustor operating at different conditions. The fluidized bed combustor heat balance was then solved for the bed ignition temperature which was influenced by both the rate of heat loss from the bed and the reactivity of the char. A sensitivity analysis suggests that the chemical rate reaction coefficient is the most prominent variable when determining the ignition temperature of a fluidized bed combustor.     

Modeling a pilot-scale fluidized bed coal gasification reactor

A steady-state model has been developed to simulate the North Carolina State University pilot-scale fluidized bed coal gasification reactor. The model involves instantaneous devolatilization of coal at the top of the gasifier (freeboard region) and char combustion and gasification in the fluidized bed. A two-phase (emulsion-dilute gas) representation of the fluidized bed incorporates the phenomena of jetting, bubbling, slugging, and mass and heat transfer between phases, and enables the prediction of individual species flow rates and temperature profiles within the bed. The model has been successfully used to simulate the gasification of a devolatilized Western Kentucky bituminous coal and a New Mexico subbituminous coal and to predict effects of various operating parameters on key gasifier performance variables.     

Optical image analysis of fine coal particles as an aid in optimizing combustion in a fluidized bed

The performance of a fluidized bed combustor is adversely affected by the entrainment of fine coal and char particles. The size distribution of the entrained particles is an indicator of the combustor's performance. Size analysis data may be helpful for optimizing the operating conditions.

An optical image analysis system (TAS, Leitz) was used to analyze the size distribution of char particles elutriated from a small fluidized bed after one single pass. The TAS system discriminates between highly reflecting char particles and low-reflectance ash. The maximum size of the chars produced in these experiments was about 50 μm, almost independent of the type of coal.     

Modeling and experimental studies on single particle coal devolatilization and residual char combustion in fluidized bed

Single particle devolatilization followed by combustion of the residual coal char particle has been analyzed in a batch-fluidized bed. The kinetic scheme with distributed activation energy is used for coal devolatilization while multiple chemical reactions with volume reaction mechanism are considered for residual char combustion. Both the models couple kinetics with heat transfer. Finite Volume Method (FVM) is employed to solve fully transient partial differential equations coupled with reaction kinetics. The devolatilization model is used to predict the devolatilization time along with residual mass and particle temperature, while the combined devolatilization and char combustion model is used to predict the overall mass loss and temperature profile of coal. The computed results are compared with the experimental results of the present authors for combustion of Indian sub-bituminous coal (15% ash) in a fluidized bed combustor as well as with published experimental results for coal with low ash high volatile matter. The effects of various operating parameters like bed temperature, oxygen mole fraction in bulk phase on devolatilization time and burn-out time of coal particle in bubbling fluidized bed have been examined through simulation.     

Modelling of circulating fluidized bed combustion of a char

The combustion of a char in the 41 mm ID riser of a laboratory circulating fluidized bed combustor has been investigated at different air excesses and rates of solids (char and sand) circulating in the loop. Riser performance was characterized by an axial oxygen concentration profile as well as by the overall carbon content and particle size distribution. The proposed model accounts for carbon surface reaction, intraparticle and external diffusion, and attrition. External diffusion effects were relevant in the riser dense region where char was potentially entrapped in large clusters of inert solids. Experimental data and results of the model calculations are in satisfactory agreement.     

水平埋管在流化床稀相中的传热研究

本文研究了水平埋管在流化床稀相中的传热规律.实验表明流化床稀相中的传热可以划分为三个不同的区域.文中给出了各自的放热系数计算公式;测定了沿管子周界的局部放热系数;讨论了各主要因素对稀相传热的影响.     

Some process fundamentals of biomass gasification in dual fluidized bed

The dual fluidised bed gasification technology is prospective because it produces high caloric product gas free of N₂ dilution even when air is used to generate the gasification-required endothermic heat via in situ combustion. This study is devoted to providing the necessary process fundamentals for development of a bubbling fluidized bed (BFB) biomass gasifier coupled to a pneumatic transported riser (PTR) char combustor. In a steam-blown fluidized bed of silica sand, gasification of 1.0 g biomass, a kind of dried coffee grounds containing about 10 wt.% water, in batch format clarified first the characteristics of fuel pyrolysis (at 1073 K) under the conditions simulating that prevailing in the gasifier intended to develop. The result shown that via pyrolysis more than 60% of fuel carbon and up to 75% of fuel mass could be converted into product gas, while the simultaneously formed char was about 22% of fuel mass. With all of these data as the known input, a process simulation using the software package ASPEN then revealed that the considered dual bed gasification plant, i.e. a BFB gasifier + a PTR combustor, is able to sustain its independent heat and mass balances to allow cold gas efficiencies higher than 75%, given that the fuel has suitable water contents and the heat carried with the product gas from the gasifier and with the flue gas from the char combustor is efficiently recovered inside the plant. In a dual fluidized bed pilot gasification facility simulating the gasification plant for development, the article finally demonstrated experimentally that the necessary reaction time for fuel, i.e. the explicit residence time of fuel particles inside the BFB gasifier computed according to a plug granular flow assumption, can be lower than 160 s. The results shown that varying the residence time from 160 to 1200 s only slightly increased the gasification efficiency, but the reaction time available in the PTR, say, about 3 s in our case, was too short to assure the finish even of fuel pyrolysis.     

Characterization of the devolatilization rate of solid fuels in fluidized beds by time‐resolved pressure measurements

The characterization of volatile matter (VM) release from solid fuel particles during fluidized‐bed combustion/gasification is relevant to the assessment of the reactor performance, as devolatilization rate affects in‐bed axial fuel segregation and VM distribution across the reactor. An experimental technique for the characterization of the devolatilization rate of solid fuels in fluidized beds is proposed. It is based on the analysis of the time series of pressure measured in a bench‐scale fluidized‐bed reactor as VM is released from a batch of fuel particles. A remarkable feature of the technique is the possibility to follow fast devolatilization with excellent time‐resolution. A mathematical model of the experiment has been developed to determine the time‐resolved devolatilization rate, the devolatilization time and the volume‐based mean molecular weight of the emitted volatile compounds. Devolatilization kinetics has been characterized for different solid fuels over a broad range of particle sizes. © 2011 American Institute of Chemical Engineers AIChE J, 2012     

An analytical model for freeboard and in-bed limestone sulfation in fluidized-bed coal combustors

A new model, which combines in-bed and freeboard sulfation, significantly improves the ability to predict sulfur capture by limestone sorbents in fluidized-bed coal combustors. In this model, the in-bed hydrodynamics are described in terms of a bubble phase and an emulsion phase while the freeboard region has only a diluted emulsion phase. The solids, which are in the emulsion phases, are considered to be completely back-mixed; the gaseous bubble phase travels in plug-flow but exchanges with the emulsion phase. The sulfation reaction occurs principally in the emulsion phase and the reaction rate is a direct function of the sulfur dioxide concentration, the extent of the calcium oxide conversion (as measured by a thermogravimetric analyzer), and the amount of limestone present in the bed and in the freeboard. The amount present, or holdup, in the free-board is calculated from empirical correlations for elutriation and from particle-time trajectories as predicted from equations of motion.The model indicates that a significant amount of sulfur capture can occur in the freeboard region, especially with high superficial gas velocities and small particle sizes, both of which lead to increased freeboard holdup. For an overall sulfur retention of 90%, approximately 9% of the sulfur is predicted to be captured within the freeboard above a combustor bed 1.8 m by 1.8 m by 1.2 m high of 1200 μm diameter limestone particles that are fluidized at 2.4 m/s. The model also predicts that the sulfur captured by the entrained particles is negligible. These predictions compare favorably with the actual sulfur retentions experienced in similar sized pilot-scale combustors.