Mechanical properties of randomly oriented short Sansevieria cylindrica fibre/polyester composites

The tensile, flexural and impact properties of randomly oriented short Sansevieria cylindrica fibre/polyester (SCFP) composites are described for the first time in this work. Composites were fabricated using raw S. cylindrica fibres (SCFs) with varying fibre lengths and weight percents of fibre. When the length of the SCFs was increased, the tensile, flexural and impact properties of the composite were increased up to a 30-mm fibre length, and then a curtailment in properties occurred for higher fibre length composites. SCFP composites showed a regular trend of an increase in properties with fibre weight percent until 40% and afterwards a decrease in properties for composites with greater fibre weight percent. Tensile tests revealed that the tensile strength was about 76 MPa, the Young’s modulus was 1.1 GPa and the elongation at break was between 7% and 8.3%. The flexural strength and modulus were estimated to be around 84 MPa and 3 GPa, respectively. Impact tests exhibited a strength of approximately 9.5 J/cm². The analysis of the tensile, flexural and impact properties of short SCFP composites displayed a critical fibre length and optimum fibre weight percent of 30 mm and 40%, respectively. Scanning electron microscope (SEM) studies were carried out to evaluate the fibre/matrix interactions. The experimental tensile strengths were compared with the theoretical predictions and found to be in good agreement with Hirsch’s model. An X-ray diffraction (XRD) analysis of the composites exposed the presence of cellulose IV with a crystallinity index of 60% and crystallite size of 68 nm.     

Mechanical property analysis of kenaf–glass fibre reinforced polymer composites using finite element analysis

Nowadays, natural fibres are used as a reinforcing material in polymer composites, owing to severe environmental concerns. Among many different types of natural resources, kenaf plants have been extensively exploited over the past few years. In this experimental study, partially eco-friendly hybrid composites were fabricated by using kenaf and glass fibres with two different fibre orientations of 0° and 90°. The mechanical properties such as tensile, flexural and impact strengths of these composites have been evaluated. From the experiment, it was observed that the composites with the 0° fibre orientation can withstand the maximum tensile strength of 49.27 MPa, flexural strength of 164.35 MPa, and impact strength of 6 J. Whereas, the composites with the 90° fibre orientation hold the maximum tensile strength of 69.86 MPa, flexural strength of 162.566 MPa and impact strength of 6.66 J. The finite element analysis was carried out to analyse the elastic behaviour of the composites and to predict the mechanical properties by using NX Nastran 9.0 software. The experimental results were compared with the predicted values and a high correlation between the results was observed. The morphology of the fractured surfaces of the composites was analysed using a scanning electron microscopy analysis. The results indicated that the properties were in the increasing trend and comparable with pure synthetic fibre reinforced composites, which shows the potential for hybridization of kenaf fibre with glass fibre.     

Mechanical properties of 3D KD-I SiCf/SiC composites with engineered fibre-matrix interfaces

Three-dimensional (3D) silicon carbide (SiC) matrix composites reinforced with KD-I SiC fibres were fabricated by precursor impregnation and pyrolysis (PIP) process. The fibre-matrix interfaces were tailored by pre-coating the as-received KD-I SiC fibres with PyC layers of different thicknesses or a layer of SiC. Interfacial characteristics and their effects on the composite mechanical properties were evaluated. The results indicate that the composite reinforced with as-received fibre possessed an interfacial shear strength of 72.1 MPa while the composite reinforced with SiC layer coated fibres had a much higher interfacial shear strength of 135.2 MPa. However, both composites showed inferior flexural strength and fracture toughness. With optimised PyC coating thickness, the interface coating led to much improved mechanical properties, i.e. a flexural strength of 420.6 MPa was achieved when the interlayer thickness is 0.1 μm, and a fracture toughness of 23.1 MPa m^1/2 was obtained for the interlayer thickness of 0.53 μm. In addition, the composites prepared by the PIP process exhibited superior mechanical properties over the composites prepared by the chemical vapour infiltration and vapour silicon infiltration (CVI-VSI) process.     

Development of kenaf-glass reinforced unsaturated polyester hybrid composite for structural applications

The main aim of this paper is to develop kenaf-glass (KG) fibres reinforced unsaturated polyester hybrid composite on a source of green composite using sheet moulding compound process. Unsaturated polyester resin (UPE) and KG fibres in mat form were used at a ratio of 70:30 (by volume) with treated and untreated kenaf fibre. The kenaf fibre was treated with 6% sodium hydroxide (NaOH) diluted solution for 3 h using mercerization method. The hybrid composites were tested for flexural, tensile and Izod impact strength using ASTM D790-03, ASTM D618 and ASTM D256-04 standards respectively. The highest flexural, tensile and impact strength were obtained from treated kenaf with 15/15 v/v KG fibres reinforced UPE hybrid composite in this investigation.Scanning electron microscopy fractography showed fibre cracking, debonding and fibre pulled-out as the main fracture mode of composites and kenaf treated 15/15 v/v KG reinforced hybrid composite exhibited better interfacial bonding between the matrix and reinforcement compared to other combinations.     

Using synchroton radiation-based micro-computer tomography (SR μ-CT) for the measurement of fibre orientations in cellulose fibre-reinforced polylactide (PLA) composites

The present work deals with the measurement of fibre orientation angles in composites. A study by Bax and Müssig [1] investigated the mechanical properties (tensile and impact characteristics) of injection-moulded flax and Cordenka-reinforced polylactide (PLA) composites with fibre mass fractions between 10 and 30 %. Raising the fibre content from 10 to 30 % resulted in an increase in tensile characteristics, but it was noted that a reinforcement with 10 % flax fibres led to poorer tensile strength as compared to the neat PLA matrix. This behaviour was not expected and needs clarification. Therefore, test specimens with a fibre content of 10 and 30 mass % were examined for their fibre orientations and void content. For the investigations, microcomputer tomography images were created by monochromatic synchrotron radiation. Fibre orientation angles of these micrographs were determined with an adapted measuring mask of the Fibreshape software. It could be shown that the fibre orientation in the composite is dependent on the fibre mass fraction and the type of fibre. No voids were found in all the investigated composites. The average fibre orientation angle of 10 % flax/PLA showed a larger deviation from the longitudinal axis of the test specimen than the other samples, and is made primarily responsible for the lower tensile strength of this composite.     

Polyoxymethylene composites with natural and cellulose fibres: Toughness and heat deflection temperature

Cellulose and abaca fibre reinforced polyoxymethylene (POM) composites were fabricated using an extrusion coating (double screw) compounding followed by injection moulding. The long cellulose or abaca fibres were dried online with an infrared dryer and impregnated fibre in matrix material by using a special extrusion die. The fibre loading in composites was 30 wt.%. The tensile properties, flexural properties, Charpy impact strength, falling weight impact strength, heat deflection temperature and dynamic mechanical properties were investigated for those composites. The fibre pull-outs, fibre matrix adhesion and cracks in composites were investigated by using scanning electron microscopy. It was observed that the tensile strength of composites was found to reduce by 18% for abaca fibre and increase by 90% for cellulose fibre in comparison to control POM. The flexural strength of composites was found to increase by 39% for abaca fibre and by 144% for cellulose fibre. Due to addition of abaca or cellulose fibre both modulus properties were found to increase 2-fold. The notched Charpy impact strength of cellulose fibre composites was 6-fold higher than that of control POM. The maximum impact resistance force was shorted out for cellulose fibre composites. The heat deflection temperature of abaca and cellulose fibre composites was observed to be 50 °C and 63 °C higher than for control POM respectively.     

Fabrication and testing of natural fibre composites: Vakka, sisal, bamboo and banana

A study has been carried out to investigate the tensile, flexural and dielectric properties of composites made by reinforcing vakka as a new natural fibre into a polyester resin matrix. The fibres extracted by retting and manual processes have been used to fabricate the composites. These composites are tested for tensile, flexural and dielectric properties and compared with those of established composites like sisal, bamboo and banana made under the same laboratory conditions. The composites are fabricated up to a maximum volume fraction of fibre of 0.37 in the case of tensile testing, and 0.39 for flexural and dielectric testing. It has been observed that the tensile properties increase with respect to volume fraction of fibre for vakka fibre composite and are also more than those of sisal and banana composites and comparable to those of bamboo composites. The flexural strength of vakka fibre composite is more than that of banana composite and is closer to sisal fibre composite with respect to the volume fraction of fibre, where as the flexural modulus is much higher than those of banana and sisal fibre composites and also very much closer to bamboo fibre composites. The dielectric strength of vakka fibre composite increases with increase in volume fraction of fibre in the composite unlike the case of sisal, bamboo and banana composites. The dielectric strength being a unique feature of vakka fibre composite, can be suggested for electrical insulation applications.     

Properties of high-alumina cement reinforced with alkali resistant glass fibres

The changes in the mechanical properties of cement composites made from high-alumina cement and Cem-FIL AR-glass fibres kept in three different environments up to 10 years are described. While the flexural and impact properties of the composite remained largely unaffected with time in a relatively dry atmosphere, in wet conditions a reduction in strength takes place. In natural weather the 10 year modulus of rupture and impact strength values are 22.8 MIN m^–2 and 6.7 KJ m^–2, respectively, corresponding to the 28 day values of 41.2 MN m^–2 and 22.8 KJ m^–2. These values are significantly better than the corresponding results obtained with Portland cement composites made from Cem-FIL fibres. High-alumina cement composites reinforced by E-glass fibre lose a very large proportion of their flexural and impact strength under wet conditions. The strength reduction with time observed for glass fibre reinforced high-alumina cement composites can be related to two sources: (a) the reduction in the strength of the glass fibre due to chemical corrosion and (b) conversion of the matrix. The latter has greater influence on those composite properties that are matrix controlled such as the Young's modulus whereas any significant reduction in fibre tensile strength is reflected in a corresponding loss in composite tensile and bending strength. Matrix conversion may also influence the fibre-matrix bond.     

Could biopolymers reinforced by randomly scattered flax fibre be used in structural applications?

Thermoplastics reinforced by natural fibres are mainly used for fitting-up products in the automotive industry. The aim of this work is to study the tensile properties of natural fibre-biopolymer composites in order to determine whether or not, biocomposites may replace glass fibre reinforced unsaturated polyester resins. The materials used are flax fibre, polylactic acid (PLA), l-polylactide acid (PLLA), poly(3-hydroxylbutyrate) (PHB), polycaprolactone and starch thermoplastic (MaterBi® Z), poly(butylene succianate) (PBS) and poly(butylene adipate-co-terephtalate) (PBAT). The tensile properties of the flax fibres have already been determined [C. Baley, Analysis of the flax fibres tensile behaviour and analysis of the tensile stiffness increase, Comp Part A 2002;33:939–948]. The composites are manufactured using a film stacking technique. After studying the processing parameters, these are then adapted to each thermoplastic composites. Test samples are cut out from the composites to test their mechanical properties under tensile loading conditions. These tensile properties are then compared to those of similar polypropylene flax composites. Preliminary results show that the tensile properties are improved with the fibre volume fraction. The tensile strength and Young’s modulus of PLLA and PLA flax composites are greater than those of similar PP/flax fibre composites. The specific tensile strength and modulus of flax fibre/PLLA composite have proved to be very close to those of glass fibre polyester composites.     

Jute/polypropylene composites I. Effect of matrix modification

Natural fibre-reinforced polymers can exhibit very different mechanical performances and environmental aging resistances depending on their interphase properties, but most studies have been focused on fibre surface treatment. Here, investigations of the effect of maleic anhydride grafted polypropylene (MAHgPP) coupling agents on the properties of jute fibre/polypropylene (PP) composites have been considered with two kinds of matrices (PP1 and PP2). Both mechanical behaviour of random short fibre composites and micro-mechanical properties of single fibre model composites were examined. Taking into account interfacial properties, a modified rule of mixture (ROM) theory is formulated which fits well to the experimental results. The addition of 2 wt% MAHgPP to polypropylene matrices can significantly improve the adhesion strength with jute fibres and in turn the mechanical properties of composites. We found that the intrinsic tensile properties of jute fibre are proportional to the fibre’s cross-sectional area, which is associated with its perfect circle shape, suggesting the jute fibre’s special statistical tensile properties. We also characterised the hydrophilic character of natural fibres and, moreover, humidity environmental aging effects. The theoretical results are found to coincide fairly well with the experimental data and the major reason of composite tensile strength increase in humidity aging conditions can be attributed to both improved polymer–matrix and interfacial adhesion strength.     

Effects of fibre length on tensile strength of carbon/glass fibre hybrid composites

The tensile strength of epoxy resin reinforced with random-planar orientation of short carbon and glass fibres increased as the length of the reinforcing fibres increased, and the increase in tensile strength remained almost unchanged after the fibre length reached a certain level. The tensile strength of composites at any fibre length could be estimated by taking the strain rate and temperature dependence of both the yield shear strength at the fibre-matrix interphase and the mean critical fibre length into consideration. The tensile strength of the hybrid composite could be estimated by the additive rule of hybrid mixtures, using the tensile strength of both composites.     

Influence of the Physical Structure of Flax Fibres on the Mechanical Properties of Flax Fibre Reinforced Polypropylene Composites

This study investigates the influence of the physical structure of flax fibres on the mechanical properties of polypropylene (PP) composites. Due to their composite-like structure, flax fibres have relatively weak lateral bonds which are in particular present in flax fibres that are often used in natural fibre mat reinforced thermoplastics (NMT). These weak bonds can be partly removed by combing the fibres. In order to study the influence of the physical structure of flax fibres on NMT tensile and flexural properties, uncombed and combed flax fibre reinforced PP composites were manufactured via a wet laid process. The influence of improved fibre-matrix adhesion was studied using maleic-anhydride grafted PP. Results indicated that the flax physical structure has a significant effect on flax-PP composite properties and that the flax fibre reinforced PP properties are similar to values predicted with existing micromechanical models. The tensile modulus of flax-PP composites can fairly compete with commercial glass mat reinforced thermoplastic (GMT) modulus, the strength, however, both tensile and flexural, can not. In order to rise the strength of flax fibre reinforced PP composites to the level of GMT strength, the flax fibres have to be further isolated to elementary flax fibres.     

Microwave heating as a means for carbon fibre recovery from polymer composites: a technical feasibility study

Carbon fibre composites with an epoxy resin matrix were subjected to microwave-heating experiments in order to volatilise the polymer content and to produce clean fibres for potential reuse in high-grade applications. The composites were processed at 3 kW for 8 s in a multimode microwave applicator. The recovered fibres were characterised by tensile tests and electron microscopy. The results compare favourably with virgin fibre properties.     

The potential of harakeke fibre as reinforcement in polymer matrix composites including modelling of long harakeke fibre composite strength

Mechanical properties of aligned long harakeke fibre reinforced epoxy with different fibre contents were evaluated. Addition of fibre was found to enhance tensile properties of epoxy; tensile strength and Young’s modulus increased with increasing content of harakeke fibre up to 223 MPa at a fibre content of 55 wt% and 17 GPa at a fibre content of 63 wt%, respectively. The flexural strength and flexural modulus increased to a maximum of 223 MPa and 14 GPa, respectively, as the fibre content increased up to 49 wt% with no further increase with increased fibre content. The Rule of Mixtures based model for estimating tensile strength of aligned long fibre composites was also developed assuming composite failure occurred as a consequence of the fracture of the lowest failure strain fibres taking account porosity of composites. The model was shown to have good accuracy for predicting the strength of aligned long natural fibre composites.     

Polypropylene composites with enzyme modified abaca fibre

Abaca fibre reinforced PP composites were prepared using a high speed mixer followed by injection moulding with 30 wt.% of fibre load. Prior to composite production, the fibres were modified by fungamix and natural enzyme. The effects of modification of the fibre were assessed on the basis of morphology and thermal resistance and as well as on mechanical, thermal and environmental stress corrosion resistance properties of the resulting composites. Coupling agent (MA-PP) was also used with unmodified abaca fibre to observe the coupling agent effect on resulting composites properties. The moisture absorption of the composites was found to be reduced 20–45% due to modification. Tensile strength found to be 5–45% and flexural strengths found to be 10–35% increased due to modification. Modified fibre composites found to better resistance in acid and base medium.     

Experimental and theoretical studies on the properties of injection moulded glass fibre reinforced mixed plastics composites

Recycled mixed post-consumer and post-industrial plastic wastes consisting of HDPE, LDPE and PP were injection moulded with short glass fibre (10–30% by weight) to produce a new generation composite materials. Intensive experimental studies were then performed to characterise the tensile, compression and flexural properties of glass fibre reinforced mixed plastics composites. With the addition of 30 wt.% of glass fibre, the strength properties and elastic modulus increased by as much as 141% and 357%, respectively. The best improvement is seen in the flexural properties due to the better orientation of the glass fibres in the longitudinal direction at the outer layers. The randomness and length of the glass fibre were accounted to modify the existing rule of mixture and fibre model analysis to reliably predict the elastic and strength properties of glass fibre reinforced mixed plastics composites.     

Silicon carbide (NicalonTM) fibre-reinforced borosilicate glass composites: mechanical properties

The objective of this study was to assess the applicability of an extrinsic carbon coating to tailor the interface in a unidirectional NicalonTM–borosilicate glass composite for maximum strength. Three unidirectional NicalonTM fibre-reinforced borosilicate glass composites were fabricated with different interfaces by using (1) uncoated (2) 25 nm thick carbon-coated and (3) 140 nm thick carbon coated Nicalon fibres. The tensile behaviours of the three systems differed significantly. Damage developments during tensile loading were recorded by a replica technique. Fibre–matrix interfacial frictional stresses were measured. A shear lag model was used to quantitatively relate the interfacial properties, damage and elastic modulus. Tensile specimen design was varied to obtain desirable failure mode. Tensile strengths of NicalonTM fibres in all three types of composites were measured by the fracture mirror method. Weibull analysis of the fibre strength data was performed. Fibre strength data obtained from the fracture mirror method were compared with strength data obtained by single fibre tensile testing of as-received fibres and fibres extracted from the composites. The fibre strength data were used in various composite strength models to predict strengths. Nicalon–borosilicate glass composites with ultimate tensile strength values as high as 585 MPa were produced using extrinsic carbon coatings on the fibres. Fibre strength measurements indicated fibre strength degradation during processing. Fracture mirror analysis gave higher fibre strengths than extracted single fibre tensile testing for all three types of composites. The fibre bundle model gave reasonable composite ultimate tensile strength predictions using fracture mirror based fibre strength data. Characterization and analysis suggest that the full reinforcing potential of the fibres was not realized and the composite strength can be further increased by optimizing the fibre coating thickness and processing parameters. The use of microcrack density measurements, indentation–frictional stress measurements and shear lag modelling have been demonstrated for assessing whether the full reinforcing and toughening potential of the fibres has been realized. This revised version was published online in November 2006 with corrections to the Cover Date.     

Mechanical properties of natural fibre reinforced polymer composites

During the last few years, natural fibres have received much more attention than ever before from the research community all over the world. These natural fibres offer a number of advantages over traditional synthetic fibres. In the present communication, a study on the synthesis and mechanical properties of new series of green composites involving Hibiscus sabdariffa fibre as a reinforcing material in urea-formaldehyde (UF) resin based polymer matrix has been reported. Static mechanical properties of randomly oriented intimately mixed Hibiscus sabdariffa fibre reinforced polymer composites such as tensile, compressive and wear properties were investigated as a function of fibre loading. Initially urea-formaldehyde resin prepared was subjected to evaluation of its optimum mechanical properties. Then reinforcing of the resin with Hibiscus sabdariffa fibre was accomplished in three different forms: particle size, short fibre and long fibre by employing optimized resin. Present work reveals that mechanical properties such as tensile strength, compressive strength and wear resistance etc of the urea-formaldehyde resin increases to considerable extent when reinforced with the fibre. Thermal (TGA/DTA/DTG) and morphological studies (SEM) of the resin and biocomposites have also been carried out.     

Procedural influences on compression and injection moulded cellulose fibre-reinforced polylactide (PLA) composites: Influence of fibre loading,fibre length,fibre orientation and voids

The influence of fibre loading (20, 30, 40 mass%), fibre fineness, and the processing procedure (compression moulding – CM and injection moulding – IM) on the tensile and impact strength of lyocell/PLA composites was examined. The results revealed a significantly higher tensile and impact strength for CM composites compared to IM composites. An increase in strength up to a fibre loading of 40% was determined for CM composites, while for IM composites the highest values were measured at a fibre loading of 30%. Composites were investigated for their void content, fibre orientation, fibre length and process-induced fibre damage. A better fibre/matrix adhesion and compaction of IM composites was found while fibre orientation as well as mechanical properties of extracted fibres show no significant differences between CM and IM composites. The different mechanical characteristics of CM and IM samples are attributed predominantly to the fibre aspect ratio and the distribution of voids.     

Woven hybrid composites: Tensile and flexural properties of oil palm-woven jute fibres based epoxy composites

In this research, tensile and flexural performance of tri layer oil palm empty fruit bunches (EFB)/woven jute (Jw) fibre reinforced epoxy hybrid composites subjected to layering pattern has been experimentally investigated. Sandwich composites were fabricated by hand lay-up technique in a mould and cured with 105 °C temperatures for 1 h by using hot press. Pure EFB and woven jute composites were also fabricate for comparison purpose. Results showed that tensile and flexural properties of pure EFB composite can be improved by hybridization with woven jute fibre as extreme woven jute fibre mat. It was found that tensile and flexural properties of hybrid composite is higher than that of EFB composite but less than woven jute composite. Statistical analysis of composites done by ANOVA-one way, it showed significant differences between the results obtained. The fracture surface morphology of the tensile samples of the hybrid composites was performed by using scanning electron microscopy.