Optimization of surface roughness and flank wear using the Taguchi method in milling of Hadfield steel with PVD and CVD coated inserts

In this paper, the Taguchi method and regression analysis have been applied to evaluate the machinability of Hadfield steel with PVD TiAlN- and CVD TiCN/Al₂O₃-coated carbide inserts under dry milling conditions. Several experiments were conducted using the L₁₈ (2 × 3 × 3) full-factorial design with a mixed orthogonal array on a CNC vertical machining center. Analysis of variance (ANOVA) was used to determine the effects of the machining parameters on surface roughness and flank wear. The cutting tool, cutting speed and feed rate were selected as machining parameters. The analysis results revealed that the feed rate was the dominant factor affecting surface roughness and cutting speed was the dominant factor affecting flank wear. Linear and quadratic regression analyses were applied to predict the outcomes of the experiment. The predicted values and measured values were very close to each other. Confirmation test results showed that the Taguchi method was very successful in the optimization of machining parameters for minimum surface roughness and flank wear in the milling the Hadfield steel.     

Suppression of notch wear of a whisker reinforced ceramic tool in air-jet-assisted high-speed machining of Inconel 718

This paper describes the notch and flank wear specific to a SiC whisker reinforced alumina tool in air jet assisted (AJA) turning of nickel-base superalloy Inconel 718 at high cutting speeds. An AJA machining experiment has revealed that the air jet applied to the tool tip in addition to coolant dramatically reduces the depth-of-cut notch wear. As a result, the width of flank wear, but not the size of notch wear, determined the life of a ceramic tool in AJA machining of Inconel 718. This is a reason for the large extension and small variation of the tool life when high speed AJA machining is adopted. The maximum tool life length reached 2160 m at a cutting speed of 660 m/min under the given cutting conditions. Finally, the mechanisms of the notch and flank wear of a SiC whisker reinforced alumina tool in AJA machining are discussed from the viewpoints of tribochemical reactions and tool wear anisotropy.     

Tool wear analysis and improvement of cutting conditions using the high-pressure water-jet assistance when machining the Ti17 titanium alloy

This paper presents experimental results concerning the machinability of the titanium alloy Ti17 with and without high-pressure water jet assistance (HPWJA) using uncoated WC/Co tools. For this purpose, the influence of the cutting speed and the water jet pressure on the evolution of tool wear and cutting forces have been investigated. The cutting speed has been varied between 50 m/min and 100 m/min and the water jet pressure has been varied from 50 bar to 250 bar. The optimum water jet pressure has been determined, leading to an increase in tool life of approximately 9 times. Compared to conventional lubrication, an increase of about 30% in productivity can be obtained.     

Wear mechanisms of PcBN cutting tools when dry turning ASTM Grade 2 austempered ductile iron under finishing conditions

Experimental studies of dry finish turning of ASTM Grade 2 austempered ductile iron with PcBN cutting tools were carried out at cutting speeds ranging from 50 to 800 m/min, at a feed of 0.05 mm/rev and depth cut of 0.2 mm. The wear mechanisms of PcBN cutting tools were investigated through the examination of the wear surfaces by means of optical, scanning electron and transmission electron microscopes as well as energy dispersive spectroscopy. Flank wear and crater wear were the main wear modes within this range of cutting speeds. Adhesion and adhesion induced abrasion were the main wear mechanisms at cutting speeds less than 150 m/min. Abrasion and wear by thermally activated-diffusion and oxidation-chemical reaction wear were the main wear mechanisms at cutting speeds greater than 150 m/min. A high concentration of Mg, Si, and O on the wear surfaces and a heat-affected zone in the tools suggested that at speeds in excess of 150 m/min, the rate controlling wear mechanism involved chemical reaction between the tools and the operating environment.     

The effect of oil mist supply on cutting point temperature and tool wear in driven rotary cutting

We examined cutting point temperature and tool wear in driven rotary cutting. Cutting tests under dry and minimum-quantity-lubrication (MQL) conditions of stainless steel (SUS304) were carried out. Cutting point temperature was measured using a tool-work-thermocouple method at various cutting speeds. Cutting point temperature tends to increase with increased cutting speed. In driven rotary cutting, cutting point temperature was lower than that of non-rotation cutting. At high-speed cutting of 500 m/min, cutting point temperature was over 1200 °C in the non-rotation tool, but 1000 °C with driven rotary cutting. In addition, when driven rotary cutting was used with MQL, cutting point temperature was decreased to 900 °C. The magnitude of tool wear corresponded almost precisely to cutting point temperature. Severe adhesion on the rake face was observed and resulted in progressive wear on the rake face in rotary cutting at a cutting speed of 100 m/min. The appropriate cutting speed range passively shifts higher from the viewpoint of cutting temperature with rotary cutting.     

Wear mechanisms of WC coated and uncoated tools in finish turning of Inconel 718

This paper presents the results of an experimental investigation on the wear mechanisms of uncoated tungsten carbide (WC) and coated tools (single-layer (TiAlN) PVD, and triple-layer (TiCN/Al₂O₃/TiN) CVD) in oblique finish turning of Inconel 718. Tool wear rate and wear mechanisms were evaluated for cutting speeds, 50<V<100 m/min, and feed rates, 0.075<f<0.125 mm/rev, at a constant depth of cut of 0.25 mm. It was concluded that abrasive and adhesive wear were the most dominant wear mechanisms, controlling the deterioration and final failure of the WC tools. While the triple layer CVD coated tools exhibited the highest wear resistance at high cutting speeds and low feeds, uncoated tools outperformed the single and multi-layer coated tools in the low range of cutting speeds and intermediate feeds. The cutting tool with single-layer PVD coating outperformed the other tools at the medium cutting speed.     

The design and optimization of micro polycrystalline diamond ball end mill for repairing micro-defects on the surface of KDP crystal

Micro-milling is a promising approach to repair the micro-defects on the surface of KH₂PO₄ (KDP) crystal. The geometrical parameters of micro ball end mill will greatly influence the repairing process as a result of the soft brittle properties of KDP crystal. Two types of double-edged micro ball end mills were designed and a three-dimensional finite element (FE) model was established to simulate the micro milling process of KDP crystal, which was validated by the milling experiments. The rake angle of −45°, the relief angle of 45° and the cutting edge radius of 1.5–2 μm were suggested to be the optimal geometrical parameters, whereas the rake angle of −25° and the relief angle of 9° were optimal just for micro ball end mill of Type I, the configuration with the rake angles ranging from 0° to 35°, by fully considering the cutting force, and the stress–strain distribution over the entire tool and the cutting zone in the simulation. Moreover, the micro polycrystalline diamond (PCD) ball end mills adopting the obtained optimal parameters were fabricated by wire electro-discharge machining (WEDM) and grinding techniques, with the average surface roughness Ra of tool rake face and tool flank face ∼0.10 μm, and the cutting edge radius of the tool ∼1.6 μm. The influence of tool's geometrical parameters on the finished surface quality was verified by the cutting experiments, and the tool with symmetric structure was found to have a better cutting performance. The repairing outlines with Ra of 31.3 nm were processed by the self-fabricated tool, which could successfully hold the growth of unstable damage sites on KDP crystal.     

Machining with AlCr-oxinitride PVD coated cutting tools

AlCrO_xN_1−x coatings were arc deposited onto HSS drills and WC–Co end mills at N₂/O₂ ratios of 0.9–0.75 using DC or 10 kHz pulse bias. Lower O₂ content coatings had a hardness of 32.5 GPa. whereas 0.25 O₂ ratio coatings were 24–25 GPa. AlCrO_xN_1−x coated 6.35 mm Dia. HSS jobber drills were tested by drilling 2.5D holes in AISI D2. 10 kHz 0.9 N₂ 0.1 O₂ coatings drilled a mean of 17.6 holes/µm, similar to commercial AlCrN coated drills at 17.8 holes/µm, whereas DC 0.75 N₂ 0.25 O₂ coatings drilled 9 holes/µm. AlCrO_xN_1−x coated WC–Co end mills had low steady state wear in milling AISI 316L (70 m/min, MQL) and cut >24 m whereas uncoated tools cut 6 m. In contrast to drilling DC 0.75 N₂ 0.25 O₂ tools had the least corner wear and low adhesion on the rake face.     

Mirror surface machining of high-alloy steels by elliptical vibration cutting with single-crystalline diamond tools: Influence of alloy elements on diamond tool damage

Elliptical vibration cutting with single-crystalline diamond tools is applied to mirror surface machining of high-alloy steels such as cold work die steels and high-speed tool steels with a hardness of more than 60 HRC. Although practical mirror surface machining of hardened die steels such as Stavax (modified AISI 420) with a hardness of 53 HRC has been realized with the elliptical vibration cutting, lives of single-crystalline diamond tools are not sufficiently long in machining of some high-alloy steels, that may be caused by a large amount of alloy elements. In order to clarify the influence of the alloy elements on the diamond tool damage, the elliptical vibration cutting experiments are conducted on six kinds of high-alloy steels and four kinds of pure metals which are the same as the alloy elements. Mechanical properties of the alloy steels, i.e. difference in hardness between carbides and matrices, and the number of small carbides, are measured, and their influence on the micro-chippings are investigated. The chemical states of the alloy elements in high-alloy steels are analyzed using an X-ray diffraction (XRD) and an electron probe micro analyzer (EPMA), and their influence on the tool wear is discussed. Based on the investigation, a mirror surface machining of DC53, which has a high hardness of 62.2 HRC and the best machinability in the tested high-alloy steels, is demonstrated, and a mirror surface with a roughness of Rt 0.05 μm is obtained successfully.     

Tribology characteristics of magnesium alloy AZ31B and its composites

In this paper, wear characteristics of magnesium alloy, AZ31B, and its nano-composites, AZ31B/nano-Al₂O_3, processed by the disintegrated melt deposition technique are investigated. The experiments were carried out using a pin-on-disk configuration against a steel disk counterface under different sliding speeds of 1, 3, 5, 7 and 10 m/s for 10 N normal load, and 1, 3 and 5 m/s for 30 N normal load. The worn samples and wear debris were then examined under a field emission scanning electron microscopy equipped with an energy dispersive spectrometer to reveal its wear features. The wear test results show that the wear rates of the composites are gradually reduced over the sliding speed range for both normal loads. The composite wear rates are higher than that of the alloy at low speeds and lower when sliding speed further increased. The coefficient of friction results of both the alloy and composites are in the range of 0.25–0.45 and reaches minimums at 5 m/s under 10 N and 3 m/s under 30 N load. Microstructural characterization results established different dominant mechanisms at different sliding speeds, namely, abrasion, delamination, oxidation, adhesion and thermal softening and melting. An experimental wear map was then constructed.     

Nanometric cutting in a scanning electron microscope

A nanometric cutting device under high vacuum conditions in a scanning electron microscope (SEM) was developed. The performance, tool-sample positioning, and processing capacity of the nanometric cutting platform were studied. The proposed device can be used to realize a displacement of 7 μm, with a closed-loop resolution of 0.6 nm in both the cutting direction and the depth direction. Using a diamond cutting tool with an edge radius of 43 nm formed by focused ion beam (FIB) processing, nanometric cutting experiments on monocrystalline silicon were performed on the developed cutting device under SEM online observation. Chips and machining results of different depths of cut were studied during the cutting process, and cutting depths of less than 10 nm could be obtained with high repeatability. Moreover, the cutting speed was found to exhibit a strong relationship with the brittle–ductile transition depth on brittle material. The experimental results of taper cutting and sinusoidal cutting indicated that the developed device has the ability to perform multiple degrees of freedom (DOFs) cutting and to study nanoscale material removal behaviour.     

Cutting performance of nano-crystalline diamond (NCD) coating in micro-milling of Ti6Al4V alloy

Hard coatings are an important factor affecting the cutting performance of tools. In particular, they directly affect tool life, cutting forces, surface quality and burr formation in the micro-milling process. In this study, the performance of nano-crystalline diamond (NCD) coated tools was evaluated by comparing it with TiN-coated, AlCrN-coated and uncoated carbide tools in micro-milling of Ti₆Al₄V alloy. A series of micro-milling tests was carried out to determine the effects of coating type and machining conditions on tool wear, cutting force, surface roughness and burr size. Flat end-mill tools with two flutes and a diameter of 0.5 mm were used in the micro-milling process. The minimum chip thickness depending on both the cutting force and the surface roughness were determined. The results showed that the minimum chip thickness is about 0.3 times that of the cutter corner radius for Ti₆Al₄V alloy and changes very little with coating type. It was observed from wear tests that the dominant wear mechanism was abrasion. Maximum wear occurred on NCD-coated and uncoated tools. In addition, maximum burr size was obtained in the cutting process with the uncoated tool.     

Development and machining performance of a textured diamond cutting tool fabricated with a focused ion beam and heat treatment

This paper presents the fabrication method and machining performance of a textured diamond cutting tool. To improve the machining performance, a texture was fabricated on the rake face of the diamond tool with a depth of 43 nm and width of 1.8 μm by utilizing a focused ion beam (FIB) followed by heat treatment. In addition, a FIB-induced non-diamond phase that adversely affects the machining performance was removed. A machining experiment using aluminum alloy and nickel phosphorus was conducted to evaluate the proposed method. A significant decrease in friction was observed at the tool–chip interface after texturing. This corresponds to a reduced cutting force, which indicates that the machining performance of the tool was improved by texturing. The magnitude of the effect depends on the shape and direction of the texture. The textured tool was able to machine a surface topography similar to that with a non-textured tool, which indicates that the texture effect can be obtained while maintaining the quality of the machined surface by fabricating the texture far from the cutting edge.     

Optimization of surface roughness,cutting force and tool wear of nitrogen alloyed duplex stainless steel in a dry turning process using Taguchi method

In this work, the dry turning parameters of two different grades of nitrogen alloyed duplex stainless steel are optimized by using Taguchi method. The turning operations were carried out with TiC and TiCN coated carbide cutting tool inserts. The experiments were conducted at three different cutting speeds (80, 100 and 120 m/min) with three different feed rates (0.04, 0.08 and 0.12 mm/rev) and a constant depth of cut (0.5 mm). The cutting parameters are optimized using signal to noise ratio and the analysis of variance. The effects of cutting speed and feed rate on surface roughness, cutting force and tool wear were analyzed. The results revealed that the feed rate is the more significant parameter influencing the surface roughness and cutting force. The cutting speed was identified as the more significant parameter influencing the tool wear. Tool wear was analyzed using scanning electron microscope image. The confirmation tests are carried out at optimum cutting conditions. The results at optimum cutting condition are predicted using estimated signal to noise ratio equation. The predicted results are found to be closer to experimental results within 8% deviations.     

Ultra-precision grinding of optical glasses using mono-layer nickel electroplated coarse-grained diamond wheels. Part 2: Investigation of profile and surface grinding

After finishing the precision conditioning of mono-layer nickel electroplated coarse-grained diamond wheels with 151 μm (D151), 91 μm (D91) and 46 μm (D46) grain size, resp., profile and surface grinding experiments were carried out on a five-axis ultra-precision grinding machine with BK7, SF6 optical glasses and Zerodur glass ceramic. A piezoelectric dynamometer was used to measure the grinding forces, while an atomic force microscopy (AFM), white-light interferometer (WLI)) and scanning electron microscope (SEM) were used to characterize the ground surface quality in terms of micro-topography and subsurface damage. Moreover, the wear mechanics of the coarse-grained diamond wheels were analyzed and the grinding ratio was determined as well, in aiming to evaluate the grinding performance with the conditioned coarse-grained diamond wheels. Finally, the grinding results were compared with that of the fine-grained diamond wheels with regard to the ground specimen surface quality, process forces and wheel wear as a function of stock removal. The experimental results show that the precision conditioned coarse-grained diamond wheels can be applied in ductile mode grinding of optical glasses with high material removal rates, low wheel wear rates and no dressing requirement yielding excellent surface finishes with surface roughness in the nanometer range and subsurface damage in the micrometer range, demonstrating the feasibility and applicability of the newly developed diamond grinding technique for optical glasses.     

Wear behavior of Cu–La2O3 composite with or without electrical current

A new type Cu–La₂O₃ composite was fabricated by internal oxidation method using powder metallurgy. Sliding wear behavior of the Cu–La₂O₃ composites was studied by using a pin-on-disk wear tester under dry sliding conditions with or without electrical current, rubbing against GCr15 type bearing steel disk at a constant sliding speed of 20 m/s. The influence of varying applied load and electrical current was investigated. The worn surfaces were examined using scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) to determine the wear mechanisms. The results showed the Cu–La₂O₃ composites had an electrical conductivity of 81.9% IACS (International Annealed Copper Standard, 100% IACS = 58 MS/m) and a hardness of HV105. The wear rate of the Cu–La₂O₃ composite pins increased with the increase in the electrical current at high sliding speed. The main wear mechanisms of the Cu–La₂O₃ composites were found to be adhesive wear, abrasive wear and arc erosion.     

Knife-edge interferometry for cutting tool wear monitoring

This paper presents a novel technique for more easily measuring cutting tool wear using knife-edge interferometry (KEI). Unlike an amplitude splitting interferometry, such as Michelson interferometry, the proposed KEI utilizes interference of a transmitted wave and a diffracted wave at the cutting tool edge. In this study, a laser beam was incident on the cutting tool edge, and the photodetector was used to determine the interference fringes by scanning a cutting tool edge along the cutting direction. The relationship between the cutting tool wear and interferometric fringes generated by edge diffraction phenomena was established by using the cross-correlation of KEI fringes of two different cutting tool-edge conditions. The cutting tool wear produced the phase shift (attrition wear) and the decay of oscillation (abrasive wear) in the interferometric fringe. The wear characteristics of the cutting tool with a radius of curvature of 6 mm were investigated by measuring the interferometric fringes of the tool while cutting an aluminum work piece in a lathe. As a result, the attrition and abrasive wear of cutting tool showed a linear relationship of 5.62 lag/wear (μm) and 1.14E-3/wear (μm), respectively. This measurement technique can be used for directly inspecting the cutting tool wear in on-machine process at low-cost.     

Development of a novel cubic boron nitride cutting tool with a textured flank face for high-speed machining of Inconel 718

Nickel-based superalloys such as Inconel 718 offer several advantages, including high-temperature strength and high corrosion resistance; this has led to a rapid increase in the demand for such materials, particularly in the aircraft industry. In contrast, these alloys are known to be among the most difficult-to-cut materials because of their mechanical and chemical properties, and tools used for this purpose have extremely short lifetimes. Recently, cubic boron nitride (CBN), which is the second hardest of all known materials, has received significant attention as a material for cutting tools and has already established itself in many fields of application. However, the performance of CBN tools is still insufficient for practical use, especially in the high-speed machining of Inconel 718. To overcome this problem, we first conducted orthogonal cutting experiments on Inconel 718 and performed cross-sectional observations of the CBN cutting tool in order to identify its wear mechanisms in continuous cutting operations under high-speed machining conditions (300 m/min). As a result, it was found that fatal tool failure occurs through crater and flank wear because of diffusion led by high cutting temperatures and subsequent chip adhesion to the tool flank face, accompanied by cutting edge chipping. Based on these results, a CBN cutting tool with a textured flank face was newly developed to improve the cutting tool life. Experimental: results showed that micro grooves generated on the flank face significantly suppressed the cutting edge chipping and remarkably extended the lifetime of the CBN tool during high-speed machining of Inconel 718.     

FE modeling of burr size in high- speed micro-milling of Ti6Al4V

This article is focused on the finite element modeling of burr formation in high speed micromilling of Ti6Al4V. Studies show that the burr produced at the up milling side at the exit of the micromilling tool is the biggest among burrs at other locations. Therefore, side exit burr at the up milling side has been modeled through finite element modeling. Johnson cook material constitutive model has been implemented in the formulation of burr formation. Experimental work has been performed to validate the developed model. It is found that the burr height and width obtained from the simulation has been validated experimentally with a maximum error of 15%. It was found from the literature review that the cutting speed is the factor, which influences the burr formation. Therefore, the model has been further extended to study the effect of cutting speed on the burr size. A maximum tool rotation of 200,000 rpm was considered with a tool diameter of 500 μm. It is predicted from the simulation that, the burr size was reduced by 96% (both height and width) if cutting tool speed was increased from 10,000 to 200,000 rpm. Therefore, it is concluded that the cutting speed is the major factor to reduce the burr size in micromilling of Ti6Al4 V. This study shows that the high speed micromachining center can be helpful in producing the micro parts with less or no burrs. It is expected that further extension of the burr formation model can minimize the burr size to zero/near zero size.     

A comparative study on the wear properties of coarse-grained Al6061 alloy and nanostructured Al6061–Al2O3 composites

Wear behavior of nanostructured Al6061 alloy and Al6061–Al₂O₃ nanocomposites produced by milling and hot consolidation were investigated. The samples were characterized by hardness test, pin-on-disk wear test, X-ray diffraction (XRD), and scanning electron microscopy (SEM). Nanocomposites containing 3 vol% Al₂O₃ showed a maximum hardness of 235 HV and optimum wear rate of 4×10⁻³ mg/m. Increasing the amount of Al₂O₃ up to 5 vol% resulted in decrease in hardness values (∼112 HV) and a sharp rise in wear rate (∼18×10⁻³ mg/m).