A facile method to synthesize well-dispersed PtRuMoOx and PtRuWOx nanoparticles and their electrocatalytic activities for methanol oxidation

PtRuMoO_x and PtRuWO_x catalysts supported on multi-wall carbon nanotubes (MWCNTs) are prepared by ultrasonic-assisted chemical reduction method. XRD measurements indicate that Pt exists as face-centered cubic structure, Ru is alloyed with platinum, and the metal oxides exist as an amorphous structure. TEM pictures show that PtRuMoO_x and PtRuWO_x catalysts are well dispersed on the surface of MWCNTs with the particle size of about 3 nm and a narrow particle size distribution. The electrochemical properties of the catalysts for methanol electrooxidation are studied by cyclic voltammetry (CV), chronoamperometry (CA) and chronopotentiometry (CP). The onset potentials for methanol oxidation on PtRuMoO_x and PtRuWO_x are more negative than that of pure Pt catalyst, shifting negatively by about 0.20 V and have better electrocatalytic activities than PtRu/MWCNTs.     

Electrochemically synthesized large area network of CoxNiyAlz layered triple hydroxides nanosheets: A high performance supercapacitor

A network of Co_xNi_yAl_z layered triple hydroxides (LTHs) nanosheets was prepared by the potentiostatic deposition process at −1.0 V (vs. Ag/AgCl) onto stainless steel electrodes. X-ray diffraction patterns show that the Co_xNi_yAl_zLTHs belong to the hexagonal system with layered structure. Cyclic voltammetry and charge discharge measurements in the potential range of −0.1 to 0.5 V and 0.0–0.4 V, respectively, vs. Ag/AgCl in 1 M KOH electrolyte indicate that Co_xNi_yAl_zLTHs have excellent supercapacitive characteristics. The maximum specific capacitance of ∼1263 F g⁻¹ was obtained for Co_0.59Ni_0.21Al_0.20LTH. The impedance studies indicated highly conducting nature of the Co_xNi_yAl_zLTHs.     

Hydrogen production from ethanol steam reforming over core–shell structured NixOy–, FexOy–, and CoxOy–Pd catalysts

The present work focused on the investigation of the hydrogen generation through the ethanol steam reforming over the core–shell structured Ni_xO_y–, Fe_xO_y–, and Co_xO_y–Pd loaded Zeolite Y catalysts. The transmission electron microscopy (TEM) image of Ni_xO_y–Pd represented a very clear core–shell structure, but the other two catalysts, Co_xO_y– and Fe_xO_y–Pd, were irregular and non-uniform. The catalytic performances differed according to the added core metal and the support. The core–shell structured Co_xO_y–Pd/Zeolite Y provided a significantly higher reforming reactivity compared to the other catalysts. The H₂ production was maximized to 98% over Co_xO_y–Pd(50.0 wt%)/Zeolite Y at the conditions of reaction temperature 600 °C, CH₃CH₂OH:H₂O = 1:3, and GHSV (gas hourly space velocity) 8400 h⁻¹. In the mechanism that was suggested in this work, the cobalt component played an important role in the partial oxidation and the CO activation for acetaldehyde and CO₂ respectively, and eventually, cobalt increased the hydrogen yield and suppressed the CO generation.     

Effect of CO2 on layered Li1+zNi1−x−yCoxMyO2 (M = Al,Mn) cathode materials for lithium ion batteries

We investigated the effect of CO₂ on layered Li_1+zNi_1−x−yCo_xM_yO₂ (M = Al, Mn) cathode materials for lithium ion batteries which were prepared by solid-state reactions. Li_1+zNi_(1−x)/2Co_xMn_(1−x)/2O₂ (Ni/Mn mole ratio = 1) singularly exhibited high storage stability. On the other hand, Li_1+zNi_0.80Co_0.15Al_0.05O₂ samples were very unstable due to CO₂ absorption. XPS and XRD measurements showed the reduction of Ni³⁺ to Ni²⁺ and the formation of Li₂CO₃ for Li_1+zNi_0.80Co_0.15Al_0.05O₂ samples after CO₂ exposure. SEM images also indicated that the surfaces of CO₂-treated samples were covered with passivation films, which may contain Li₂CO₃. The relationship between CO₂-exposure time and CO₃²⁻ content suggests that there are two steps in the carbonation reactions; the first step occurs with the excess Li components, Li₂O for example, and the second with LiNi_0.80Co_0.15Al_0.05O₂ itself. It is well consistent with the fact that the discharge capacity was not decreased and the capacity retention was improved until the excess lithium is consumed and then fast deterioration occurred.     

Structural and transport properties of LixNi1−y−zCoyMnzO2 cathode materials

In this work structural and transport properties of layered LiNi_1−y−zCo_yMn_zO₂ (y = 0.25, 0.35, 0.5 and z = 0.1) cathode materials are presented. In the considered group of oxides, LiNi_1−y−zCo_yMn_zO₂, there is no clear correlation between electrical conductivity and the a parameter (M-M distance in the octahedra layers). A non-monotonic modification of electrical properties of Li_xNi_0.65Co_0.25Mn_0.1O₂ cathode materials is observed upon lithium deintercalation.     

Photocatalytic H2 evolution from NaCl saltwater over ZnS1−x−0.5yOx(OH)y-ZnO under visible light irradiation

Photocatalytic hydrogen production was investigated over ZnS_1−x−0.5yO_x(OH)_y-ZnO using sulfide ion (Na₂S-Na₂SO₃) as an electron donor from NaCl saltwater. NaCl can affect markedly the activity for photocatalytic hydrogen production, depending on NaCl concentration. When NaCl concentration is lower, the activity is lower than that in pure water, whereas when NaCl concentration is higher, the activity is higher than that in pure water. NaCl decreases not only the surface charge of ZnS_1−x−0.5yO_x(OH)_y-ZnO but also the surface hydration. When ZnS_1−x−0.5yO_x(OH)_y-ZnO was impregnated with the electron donor (Na₂S-Na₂SO₃), ZnO was transformed partly into ZnS. The impregnated ZnS_1−x−0.5yO_x(OH)_y-ZnO exhibits higher activity than the non-impregnated one. The possible mechanisms were discussed.     

Preparation and characterization of sub-micro LiNi0.5−xMn1.5+xO4 for 5 V cathode materials synthesized by an ultrasonic-assisted co-precipitation method

Sub-micro spinel LiNi_0.5−xMn_1.5+xO₄ (x < 0.1) cathode materials powder was successfully synthesized by the ultrasonic-assisted co-precipitation (UACP) method. The structure and electrochemical performance of this as-prepared powder were characterized by powder XRD, SEM, XPS, CV and the galvanostatic charge–discharge test in detail. XRD shows that there is a small Li_yNi_1−yO impurity peak placed close to the (4 0 0) line of the spinel LiNi_0.5−xMn_1.5+xO₄, and the powders are well crystallized. XPS exhibits that the Mn oxidation state is between +3 and +4, and Ni oxidation state is +2 in LiNi_0.5−xMn_1.5+xO₄. SEM shows that the prepared powders (UACP) have the uniform and narrow size distribution which is less than 200 nm. Galvanostatic charge–discharge test indicates that the initial discharge capacities for the LiNi_0.5−xMn_1.5+xO₄ (UACP) at C/3, 1C and 2C, are 130.2, 119.0 and 110.0 mAh g⁻¹, respectively. After 100 cycles, their capacity retentions are 99.8%, 88.2%, and 73.5%, respectively. LiNi_0.5−xMn_1.5+xO₄ (UACP) at C/3 discharge rate exhibits superior capacity retention upon cycling, and it also shows well high current discharge performance. CV curve implies that LiNi_0.5−xMn_1.5+xO₄ (x < 0.1) spinel synthesized by ultrasonic-assisted co-precipitation method has both reversibility and cycle capability because of the ultrasonic-catalysis.     

Structural and transport properties of layered Li1+x(Mn1/3Co1/3Ni1/3)1−xO2 oxides prepared by a soft chemistry method

In this work structural and transport properties of layered Li_1+x(Mn_1/3Co_1/3Ni_1/3)_1−xO₂ oxides (x = 0; 0.03; 0.06) prepared by a “soft chemistry” method are presented. The excessive lithium was found to significantly improve transport properties of the materials, a corresponding linear decrease of the unit cell parameters was observed. The electrical conductivity of Li_1.03(Mn_1/3Co_1/3Ni_1/3)_0.97O₂ composition was high enough to use this material in a form of a pellet, without any additives, in lithium batteries and characterize structural and transport properties of deintercalated Li_1.03−y(Mn_1/3Co_1/3Ni_1/3)_0.97O₂ compounds. For deintercalated samples a linear increase of the lattice parameter c together with a linear decrease of the parameter a with the increasing deintercalation degree occurred, but only up to 0.4-0.5 mol of extracted lithium. Further deintercalation showed a reversal of the trend. Electrical conductivity measurements performed of Li_1.03−y(Mn_1/3Co_1/3Ni_1/3)_0.97O₂ samples (y = 0.1; 0.3; 0.5; 0.6) showed an ongoing improvement, almost two orders of magnitude, in relation to the starting composition. Additionally, OCV measurements, discharge characteristics and lithium diffusion coefficient measurements were performed for Li/Li⁺/Li_1.03−y(Mn_1/3Co_1/3Ni_1/3)_0.97O₂ cells.     

Potentiostatically deposited nanostructured CoxNi1−x layered double hydroxides as electrode materials for redox-supercapacitors

Cobalt–nickel layered double hydroxides (Co_xNi_1−x LDHs) were deposited onto stainless steel electrodes by the potentiostatic deposition method at −1.0 V vs. Ag/AgCl using various molar ratios of Co(NO₃)₂ and Ni(NO₃)₂ in distilled water. Their structure and surface morphology were studied by using X-ray diffraction analysis, energy dispersive X-ray spectroscopy and scanning electron microscopy. A network of Co_xNi_1−x LDH nanosheets was obtained. The nature of the cyclic voltammetry and charge–discharge curves suggested that the Co_xNi_1−x LDHs exist in the form of solid solutions. The capacitive characteristics of the Co_xNi_1−x LDHs in 1 M KOH electrolyte showed that Co_0.72Ni_0.28 LDHs had the highest specific capacitance value, 2104 F g⁻¹, which is also the highest yet reported value for oxide materials in general.     

Minimization of the cation mixing in Li1+x(NMC)1−xO2 as cathode material

Li_1+x(Ni_1/3Mn_1/3Co_1/3)_1−xO₂ layered materials were synthesized by the co-precipitation method with different Li/M molar ratios (M = Ni + Mn + Co). Elemental titration evaluated by inductively coupled plasma spectrometry (ICP), structural properties studied by X-ray diffraction (XRD), Rietveld analysis of XRD data, scanning electron microscopy (SEM) and magnetic measurements carried out by superconducting quantum interference devices (SQUID) showed the well-defined α-NaFeO₂ structure with cationic distribution close to the nominal formula. The Li/Ni cation mixing on the 3b Wyckoff site of the interlayer space was consistent with the structural model [Li_1−yNi_y]_3b[Li_x+yNi_{(1−x)/3−y}Mn_(1−x)/3Co_(1−x)/3]_3aO₂ (x = 0.02, 0.04) and was very small. Both Rietveld refinements and magnetic measurements revealed a concentration of Ni²⁺-3b ions lower than 2%; moreover, for the optimized sample synthesized at Li/M = 1.10, only 1.43% of nickel ions were located into the Li sublattice. Electrochemical properties were investigated by galvanostatic charge-discharge cycling. Data obtained with Li_1+x(Ni_1/3Mn_1/3Co_1/3)_1−xO₂ reflected the high degree of sample optimization. An initial discharge capacity of 150 mAh g⁻¹ was delivered at 1 C-rate in the cut-off voltage of 3.0-4.3 V. More than 95% of its initial capacity was retained after 30 cycles at 1 C-rate. Finally, it is demonstrated that a cation mixing below 2% is considered as the threshold for which the electrochemical performance does not change for Li_1+x(Ni_1/3Mn_1/3Co_1/3)_1−xO₂.     

An amorphous LiCo1/3Mn1/3Ni1/3O2 thin film deposited on NASICON-type electrolyte for all-solid-state Li-ion batteries

Amorphous LiCo_1/3Mn_1/3Ni_1/3O₂ thin films were deposited on the NASICON-type Li-ion conducting glass ceramics, Li_1+x+yAl_xTi_2−xSi_yP_3−yO₁₂ (LATSP), by radio frequency (RF) magnetron sputtering below 130 °C. The amorphous films were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The Li/PEO₁₈-Li(CF₃SO₂)₂N/LATSP/LiCo_1/3Mn_1/3Ni_1/3O₂/Au all-solid-state cells were fabricated to investigate the electrochemical performance of the amorphous films. It was found that the low-temperature deposited amorphous cathode film shows a high discharge voltage and a high discharge capacity of around 130 mAh g⁻¹.     

The influence of compositional change of 0.3Li2MnO3·0.7LiMn1−xNiyCo0.1O2 (0.2 ≤ x ≤ 0.5, y = x − 0.1) cathode materials prepared by co-precipitation

Cathode materials prepared by a co-precipitation are 0.3Li₂MnO₃·0.7LiMn_1−xNi_yCo_0.1O₂ (0.2 ≤ x ≤ 0.4) cathode materials with a layered-spinel structure. In the voltage range of 2.0-4.6 V, the cathodes show more than one redox reaction peak during its cyclic voltammogram. The Li/0.3Li₂MnO₃·0.7LiMn_1−xNi_yCo_0.1O₂ (x = 0.3, y = 0.2) cell shows the initial discharge capacity of about 200 mAh g⁻¹. However, when x = 0.2 and y = 0.1, the cell exhibits a rapid decrease in discharge capacity and poor cycle life.     

New fan blade-like core-shell Sb2TixSy photocatalytic nanorod for hydrogen production from methanol/water photolysis

New photocatalysts of Sb₂Ti_xS_y (x = 0, 0.5, 1.0, 1.5 mol and y = 3, 4, 5, 6 mol) fan blade-like core-shell nanorods have been designed ultimately to enhance hydrogen production. The nanorods of 500 nm long and 60–100 nm wide are Sb₂S₃ nanorod surrounded by an amorphous TiS₂ membrane, showing absorption band edges of above 600 nm. The evolution of H₂ from methanol/water (1:1) photo-splitting over Sb₂Ti_xS_y nanorods in the liquid system is doubled, compared to that over pure Sb₂S₃. Particularly, 52 μmol of H₂ gas is produced after 10 h when 0.5 g of Sb₂Ti_1.0S₅ nanorods is used at pH = 7, and the performance is increased by more than 50% at higher pH. Based on cyclic voltammetry (CV) and UV-Visible absorption spectra, the high photocatalytic activity can be attributed to the existence of an appropriate band-gap state, which includes the scope of the redox potential of water in Sb₂Ti_1.0S₅ nanorods, resulting in the promotion of the redox reaction of water.     

Potentiodynamic deposition of composition influenced Co1−xNix LDHs thin film electrode for redox supercapacitors

Current paper comprises the electrodeposition of nanostructured porous Co_1−xNi_x layered double hydroxide (Co_1−xNi_x LDHs) thin films on to stainless steel substrate by a potentiodynamic mode. The compositional impacts on the various properties of Co_1−xNi_x LDHs are examined via structural, morphological, surface wettability and electrochemical studies. The nanocrystalline Co_1−xNi_x LDHs thin films possess varying porous, nanoflake like morphology and superhydrophilic behavior by the composition influence. Electrochemical studies demonstrate the supercapacitive performance of Co_1−xNi_x LDHs thin film electrodes. The maximal specific capacitance for Co_1−xNi_x LDHs electrode is found to be ∼1213 F g⁻¹ for composition Co_0.66Ni_0.34 LDH in 2 M KOH electrolyte at 5 mV s⁻¹ scan rate owing specific energy of 104 Whkg⁻¹, specific power of 1.44 kW kg⁻¹ with ∼94% of coulomb efficiency and stability of electrode retained to 77% after 10,000th cycle. The high capacitance retention proposes the deposited Co_1−xNi_x LDHs thin film as promising contender for supercapacitor applications.     

Pd-Ni electrocatalysts for efficient ethanol oxidation reaction in alkaline electrolyte

Pd_xNi_y/C catalysts with high ethanol oxidation reaction (EOR) activity in alkaline solution have been prepared through a solution phase-based nanocapsule method. XRD and TEM show Pd_xNi_y nanoparticles with a small average diameter (2.4-3.2 nm) and narrow size distribution (1-6 nm) were homogeneously dispersed on carbon black XC-72 support. The EOR onset potential on Pd₄Ni₅/C (−801 mV vs. Hg/HgO) was observed shifted 180 mV more negative than that of Pd/C. Its exchange current density was 33 times higher than that of Pd/C (41.3 × 10⁻⁷ A/cm²vs. 1.24 × 10⁻⁷ A/cm²). After a 10,000-s chronoamperometry test at −0.5 V (vs Hg/HgO), the EOR mass activity of Pd₂Ni₃/C survived at 1.71 mA/mg, while that of Pd/C had dropped to 0, indicating Pd_xNi_y/C catalysts have a better ’detoxification’ ability for EOR than Pd/C. We propose that surface Ni could promote refreshing Pd active sites, thus enhancing the overall ethanol oxidation kinetics. The nanocapsule method is able to not only control over the diameter and size distribution of Pd-Ni particles, but also facilitate the formation of more efficient contacts between Pd and Ni on the catalyst surface, which is the key to improving the EOR activity.     

Studies on B sites in Fe-doped LaNiO3 perovskite for SCR of NOx with H2

A series of LaNi_1−xFe_xO₃ (x = 0.0, 0.2, 0.4, 0.7, and 1.0) perovskites were synthesized and characterized by X-ray diffraction (XRD), N₂ physisorption, scanning electron microscopy (SEM), H₂-temperature-programmed reduction (H₂-TPR), and X-ray photoelectron spectroscopy (XPS). The perovskites were investigated for selective catalytic reduction of NO_x by hydrogen (H₂-SCR). It is shown that Fe addition into LaNiO₃ leads to a promoted efficiency of NO_x removal, as well as a high stability of perovskite structure. Moreover, easy reduction of Ni³⁺ to Ni²⁺ with the aid of appropriate Fe component mainly accounts for the enhanced activity. Meanwhile, deactivation of the sulfated catalysts is due to that sulfates mainly deposit on active Ni component while doping of Fe can protect Ni to some extent at the expense of partial sulfation.     

Synthesis and electrochemical properties of Li1−xFe0.8Ni0.2O2–LixMnO2 (Mn/(Fe + Ni + Mn) = 0.8) material

A new type of Li_1−xFe_0.8Ni_0.2O₂–Li_xMnO₂ (Mn/(Fe + Ni + Mn) = 0.8) material was synthesized at 350 °C in air atmosphere using a solid-state reaction. The material had an XRD pattern that closely resembled that of the original Li_1−xFeO₂–Li_xMnO₂ (Mn/(Fe + Mn) = 0.8) with much reduced impurity peaks. The Li/Li_1−xFe_0.8Ni_0.2O₂–Li_xMnO₂ cell showed a high initial discharge capacity above 192 mAh g⁻¹, which was higher than that of the parent Li/Li_1−xFeO₂–Li_xMnO₂ (186 mAh g⁻¹). We expected that the increase of initial discharge capacity and the change of shape of discharge curve for the Li/Li_1−xFe_0.8Ni_0.2O₂–Li_xMnO₂ cell is the result from the redox reaction from Ni²⁺ to Ni³⁺ during charge/discharge process. This cell exhibited not only a typical voltage plateau in the 2.8 V region, but also an excellent cycle retention rate (96%) up to 45 cycles.     

Effect of Ni content on the hydrogen storage behavior of ZrCo1−xNix alloys

ZrCo_1−xNi_x (x = 0, 0.1, 0.2 and 0.3) alloys were prepared and their hydrogen storage behavior were studied. ZrCo_1−xNi_x alloys of compositions with x = 0, 0.1, 0.2 and 0.3 prepared by arc-melting method and characterized by X-ray diffraction analysis. XRD analysis showed that the alloys of composition with x = 0, 0.1, 0.2 and 0.3 forms cubic phase similar to ZrCo with traces of ZrCo₂ phase. A trace amount of an additional phase similar to ZrNi was found for the alloy with composition x = 0.3. Hydrogen desorption pressure–composition–temperature (PCT) measurements were carried out using Sievert's type volumetric apparatus and the hydrogen desorption pressure–composition isotherms (PCIs) were generated for all the alloys in the temperature range of 523–603 K. A single sloping plateau was observed for each isotherm and the plateau pressure was found to increase with increasing Ni content in ZrCo_1−xNi_x alloys at the same experimental temperature. A van't Hoff plot was constructed using plateau pressure data of each pressure–composition isotherm and the thermodynamic parameters were calculated for desorption of hydrogen in the ZrCo_1−xNi_x–H₂ systems. The enthalpy and entropy change for desorption of hydrogen were calculated. In addition, the hydrogen absorption–desorption cyclic life studies were performed on ZrCo_1−xNi_x alloys at 583 K up to 50 cycles. It was observed that with increasing Ni content the durability against disproportionation of alloys increases.     

Synthesis and characterization of LiNi0.6Mn0.4−xCoxO2 as cathode materials for Li-ion batteries

LiNi_0.6Co_xMn_0.4−xO₂ (x = 0.05, 0.10, 0.15, 0.2) cathode materials are prepared, and their structural and electrochemical properties are investigated using X-ray diffraction (XRD), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), differential scanning calorimetric (DSC) and charge–discharge test. The results show that well-ordering layered LiNi_0.6Co_xMn_0.4−xO₂ (x = 0.05, 0.10, 0.15, 0.2) cathode materials are successfully prepared in air at 850 °C. The increase of the Co content in LiNi_0.6Mn_0.4−xCo_xO₂ leads to the acceleration of the grain growth, the increase of the initial discharge capacity and the deterioration of the cycling performance of LiNi_0.6Mn_0.4−xCo_xO₂. It also leads to the enhancement of the ratio Ni³⁺/Ni²⁺ in LiNi_0.6Co_xMn_0.4−xO₂, which is approved by the XPS analysis, resulting in the increase of the phase transition during cycling. This is speculated to be main reason for the deteriotion of the cycling performance. All synthesized LiNi_0.6Co_xMn_0.4−xO₂ samples charged at 4.3 V show exothermic peaks with an onset temperature of larger than 255 °C, and give out less than 400 J g⁻¹ of total heat flow associated with the peaks in DSC analysis profile, exhibiting better thermal stability. LiNi_0.6Co_0.05Mn_0.35O₂ with low Co content and good thermal stability presents a capacity of 156.6 mAh g⁻¹ and 98.5% of initial capacity retention after 50 cycles, showing to be a promising cathode materials for Li-ion batteries.