Photocatalytic water splitting with In-doped H2LaNb2O7 composite oxide semiconductors

The In-doped HLaNb₂O₇ oxide semiconductors synthesized by solid-state reaction followed by an ion-exchange reaction were found to be a novel composite photocatalyst system with enhanced activity for water splitting. Pt was incorporated in the interlayer of In-doped HLaNb₂O₇ by the stepwise intercalation reaction. The In-doped HLaNb₂O₇ powder samples were characterized with X-ray diffraction (XRD) and UV-vis diffuse reflectance spectrometry. The photocatalytic activities of Pt-loaded In-doped HLaNb₂O₇ and individual precursor materials were evaluated by H₂ evolution from aqueous CH₃OH solution under UV light irradiation. It was found that the composite In-doped HLaNb₂O₇ showed a higher H₂ evolution rate in comparison with individual materials. The hydrogen production activity of In-doped HLaNb₂O₇ was greatly enhanced by Pt co-incorporation. The In content in the In-doped HLaNb₂O₇ system was discussed in relation to the photophysical and photocatalytic properties. As In content equal 5 mol%, the HLaNb₂O₇:In/Pt showed a photocatalytic activity of 354 cm³ g⁻¹ hydrogen evolution in 10 vol% methanol solution under irradiation from a 100 W mercury lamp at 333 K for 3 h.     

Electrospun Pt/TiO2 hybrid nanofibers for visible-light-driven H2 evolution

One-dimensional (1D) Pt/TiO₂ hybrid nanofibers (HNFs) with different concentrations of Pt were fabricated by a facile two-step synthesis route combining an electrospinning technique and calcination process. X-ray diffraction (XRD), scanning electron microscopy (SEM), and high-resolution transmission electron microscopy (HRTEM) results showed that the Pt nanoparticles (NPs) with the size of 5–10 nm were well dispersed in the TiO₂ nanofibers (NFs). Further investigations from the UV–Vis diffuse reflectance (DR) and X-ray photoelectron spectroscopy (XPS) analysis revealed that some Pt ions were incorporated into the TiO₂ lattice as Pt⁴⁺ state, which contributed to the visible light absorption of TiO₂ NFs. Meanwhile, the Pt²⁺ ions existing on the surface of Pt NPs resulted in the formation of Pt–O–Ti bond at Pt NPs/TiO₂ NFs interfaces that might serve as an effective channel for improving the charge transfer. The as-electrospun Pt/TiO₂ HNFs exhibited remarkable activities for photocatalytic H₂ evolution under visible light irradiation in the presence of l-ascorbic acid as the sacrificial agent. In particular, the optimal HNFs containing 1.0 at% Pt showed the H₂ evolution rate of 2.91 μmol h⁻¹ and apparent quantum efficiency of 0.04% at 420 nm by using only 5 mg of photocatalysts. The higher photocatalytic activity could be ascribed to the appropriate amount of Pt ions doping and excellent electron-sink effect of Pt NPs co-catalysts.     

CuCr2O4/TiO2 heterojunction for photocatalytic H2 evolution under simulated sunlight irradiation

CuCr₂O₄/TiO₂ heterojunction has been successfully synthesized via a facile citric acid (CA)-assisted sol-gel method. Techniques of X-ray diffraction (XRD), transmission electron microscopy (TEM), and UV-vis diffuse reflectance spectrum (UV-vis DRS) have been employed to characterize the as-synthesized nanocomposites. Furthermore, photocatalytic activities of the as-obtained nanocomposites have been evaluated based on the H₂ evolution from oxalic acid solution under simulated sunlight irradiation. Factors such as CuCr₂O₄ to TiO₂ molar ratio in the composites, calcination temperature, photocatalyst mass concentration, and initial oxalic acid concentration affecting the photocatalytic hydrogen producing have been studied in detail. The results showed that the nanocomposite of CuCr₂O₄/TiO₂ is more efficient than their single part of CuCr₂O₄ or TiO₂ in producing hydrogen. The optimized composition of the nanocomposites has been found to be CuCr₂O₄·0.7TiO₂. And the optimized calcination temperature and photocatalyst mass concentration are 500 °C and 0.8 g l⁻¹, respectively. The influence of initial oxalic acid concentration is consistent with the Langmuir model.     

Significant improvement of photocatalytic hydrogen generation rate over TiO2 with deposited CuO

TiO₂ photocatalyst with deposited CuO (CuO-TiO₂) was synthesized by the impregnation method using P25 (Degussa) as support, and exhibited high photocatalytic hydrogen generation activity from methanol/water solution. A substantial hydrogen evolution rate of 10.2 ml min⁻¹ (18,500 μmol h⁻¹ g⁻¹_catalyst) was observed over this efficient CuO-TiO₂ with optimal Cu content of 9.1 mol% from an aqueous solution containing 10 vol% methanol; this improved hydrogen generation rate is significantly higher than the reported Cu-containing TiO₂, including some Pt and Pd loaded TiO₂. Optimal Cu content of 9.1 mol% provided maximum active sites and allowed good light penetration in TiO₂. Over this efficient CuO-TiO₂, the hydrogen generation rate was accelerated by increasing the methanol concentration according to Freundlich adsorption isotherm. However, the photocatalytic hydrogen generation rate was suppressed under long time irradiation mainly due to accumulation of by-products, reduction of CuO and copper leaching, which requires further investigation.     

Photocatalytic hydrogen production over CuO and TiO2 nanoparticles mixture

Cheap and efficient photocatalysts were fabricated by simply mixing TiO₂ nanoparticles (NPs) and CuO NPs. The two NPs combined with each other to form TiO₂/CuO mixture in an aqueous solution due to the opposite surface charge. The TiO₂/CuO mixture exhibited photocatalytic hydrogen production rate of up to 8.23 mmol h⁻¹ g⁻¹ under Xe lamp irradiation when the weight ratio of P25 to CuO was optimized to 10. Although the conduction band edge position of CuO NPs is more positive than normal hydrogen electrode, the TiO₂/CuO mixture exhibited good photocatalytic hydrogen production performance because of the inter-particle charge transfer between the two NPs. The detailed mechanism of the photocatalytic hydrogen production is discussed. This mixing method does not require a complicated chemical process and allows mass production of the photocatalysts.     

Enhanced hydrogen generation using ZrO2-modified coupled ZnO/TiO2 nanocomposites in the absence of noble metal co-catalyst

Mesoporous ZrO₂-modified coupled ZnO/TiO₂ nanocomposites were prepared by a surfactant assisted sol–gel method. The photocatalytic performance of these materials was investigated for H₂ evolution without noble metal co-catalyst using aqueous methanol media under AM1.5 simulated light. The H₂ evolution was compared with coupled ZnO/TiO₂, TiO₂, ZnO and Degussa P25. The ZrO₂-modified nanocomposites exhibited higher H₂ generation, specifically 0.5 wt.% ZrO₂ loading produced 30.78 mmol H₂ g⁻¹ compared to 3.55 mmol H₂ g⁻¹ obtained with coupled ZnO/TiO₂. A multiple absorbance thresholds at 435 nm and 417 nm were observed with 0.5 wt.% ZrO₂ loading, corresponding to 2.85 eV and 2.97 eV band gap energies. The high surface area, large pore volume, uniform crystallite sizes and enhanced light harvesting observed in ZrO₂-modified nanocomposites were contributing factors for effective charge separation and higher H₂ production. The possible mechanism of H₂ generation from aqueous methanol solution over ZrO₂-modified nanocomposite is presented.     

TiO2 nanotubes for hydrogen generation by photocatalytic water splitting in a two-compartment photoelectrochemical cell

Highly ordered TiO₂ nanotube arrays for hydrogen production have been synthesized by electrochemical anodization of titanium sheets. Under solar light irradiation, hydrogen generation by photocatalytic water splitting was carried out in the two-compartment photoelectrochemical cell without any external applied voltage. The hydrogen gas and oxygen generated on Pt side and on TiO₂ nanotubes side respectively were efficiently separated. The effect of anodization time on the morphology structures, photoelectrochemical properties and hydrogen production was systematically investigated. Due to more charge carrier generation and faster charge transfer, a maximum photoconversion efficiency of 4.13% and highest hydrogen production rate of 97 μmol h⁻¹cm⁻² (2.32 mL h⁻¹cm⁻²) were obtained from TiO₂ nanotubes anodized for 60 min.     

TiO2 nanosheets loaded with Cu: A low-cost efficient photocatalytic system for hydrogen evolution from water

Rutile TiO₂ nanosheets were prepared by a simple solvothermal process, and Cu was loaded on the surface of TiO₂ nanosheets using the in situ photo-deposition method. Meanwhile, photocatalytic H₂ evolution from water over the as-prepared TiO₂ nanosheets loaded with Cu was explored using methanol as a sacrificial reagent. The results indicate that the TiO₂ nanosheets loaded with Cu is an efficient photocatalyst under UV irradiation. During the first 5 h, a rate of H₂ evolution of approximately 22.1 mmol g⁻¹ h⁻¹ was achieved under optimal conditions. Furthermore, for practical purposes, the photocatalytic hydrogen evolution was studied as a function of content of Cu, pH of solution, concentration of methanol and dosage of photocatalyst, respectively. At last, the photocatalytic mechanism was preliminarily discussed.     

The structural characterization of (NH4)2B10H10 and thermal decomposition studies of (NH4)2B10H10 and (NH4)2B12H12

The structure of (NH₄)₂B₁₀H₁₀ (1) was determined through powder XRD analysis. The thermal decomposition of 1 and (NH₄)₂B₁₂H₁₂ (2) was examined between 20 and 1000 °C using STMBMS methods. Between 200 and 400 °C a mixture of NH₃ and H₂ evolves from both compounds; above 400 °C only H₂ evolves. The dihydrogen bonding interaction in 1 is much stronger than that in 2. The stronger dihydrogen bond in 1 resulted in a significant reduction by up to 60 °C, but with a corresponding 25% decrease in the yield of H₂ in the lower temperature region and a doubling of the yield of NH₃. The decomposition of 1 follows a lower temperature exothermic reaction pathway that yields substantially more NH₃ than the higher temperature endothermic pathway of 2. Heating of 1 at 250 °C resulted in partial conversion of B₁₀H₁₀²⁻ to B₁₂H₁₂²⁻. Both 1 and 2 form an insoluble polymeric material after decomposition. The elements of the reaction network that control the release of H₂ from the B₁₀H₁₀²⁻ can be altered by conducting the experiment under conditions in which pressures of NH₃ and H₂ are either near, or away from, their equilibrium values.     

Low-temperature preparation of AgIn5S8/TiO2 heterojunction nanocomposite with efficient visible-light-driven hydrogen production

AgIn₅S₈ and AgIn₅S₈/TiO₂ heterojunction nanocomposite with efficient photoactivity for H₂ production were prepared by a low-temperature water bath deposition process. The resultant AgIn₅S₈ shows an absorption edge at ∼720 nm, corresponding to a bandgap of ∼1.72 eV, and its visible-light-driven photoactivity (100.1 μmol h⁻¹) for H₂ evolution is 9 times higher than that (11 μmol h⁻¹) of the product derived from a hydrothermal process, while the obtained AgIn₅S₈/TiO₂ heterojunction nanocomposites prepared by using commercially available TiO₂ nanoparticles (P25) as TiO₂ source exhibit remarkably improved photoactivity as compared to the pristine AgIn₅S₈, and the AgIn₅S₈/TiO₂ nanocomposite with molar ratio of 1:10 shows a maximum photocatalytic H₂ evolution rate (371.1 μmol h⁻¹), which is 4.3 times higher than that (85 μmol h⁻¹) of the corresponding AgIn₅S₈/TiO₂ nanocomposite derived from a hydrothermal method. This significant enhancement in the photocatativity of the present AgIn₅S₈/TiO₂ nanocomposite can be ascribed to the better dispersion of the AgIn₅S₈ formed on TiO₂ nanoparticle surfaces and the more intimate AgIn₅S₈/TiO₂ heterojunction structure during the water bath deposition process under continuously stirring as compared to the corresponding nanocomposite derived from a hydrothermal method. This configuration of nanocomposite results in fast diffusion of the photogenerated carriers in AgIn₅S₈ towards TiO₂, which is beneficial for separating spatially the photogenerated carriers and improving the photoactivity. The present findings shed light on the tuning strategy of spectral responsive region and photoactivity of photocatalysts for efficient light-to-energy conversion.     

Pd-Gardenia-TiO2 as a photocatalyst for H2 evolution from pure water

The photocatalytic activity for H₂ evolution from pure water over Pd loaded TiO₂ prepared by gardenia extract (Pd-Gardenia-TiO₂) is systematically investigated. The as-prepared photocatalysts are characterized by X-ray diffraction, high resolution transmission electron microscopy, Fourier transform infrared spectra, and X-ray photoelectron spectroscopy. Gardenia extract functions as reducing and stabilizing agents simultaneously. The mean size of the as-prepared Pd nanoparticles is in the range of 2.3 ± 0.5 nm based on TEM images. The Pd-Gardenia-TiO₂ catalyst exhibits good photocatalytic activity for H₂ evolution (93 μmol · h⁻¹ · g⁻¹), which is much higher than that of Pd photodeposited on TiO₂. Possible factors for its photocatalytic activity from pure water are also investigated.     

Photocatalytic hydrogen production from aqueous methanol solution with CuO/Al2O3/TiO2 nanocomposite

The photocatalytic hydrogen production from aqueous methanol solution was investigated with ZnO/TiO₂, SnO/TiO₂, CuO/TiO₂, Al₂O₃/TiO₂ and CuO/Al₂O₃/TiO₂ nanocomposites. A mechanical mixing method, followed by the solid-state reaction at elevated temperature, was used for the preparation of nanocomposite photocatalyst. Among these nanocomposite photocatalysts, the maximal photocatalytic hydrogen production was observed with CuO/Al₂O₃/TiO₂ nanocomposites. A variety of components of CuO/Al₂O₃/TiO₂ photocatalysts were tested for the enhancement of H₂ formation. The optimal component was 0.2 wt% CuO/0.3 wt% Al₂O₃/TiO₂. The activity exhibited approximately tenfold enhancement at the optimum loading, compared with that with pure P-25 TiO₂. Nano-sized TiO₂ photocatalytic hydrogen technology has great potential for low-cost, environmentally friendly solar-hydrogen production to support the future hydrogen economy.     

Study of Pt electrode dissolution in H2O2-containing H2SO4 solution using an electrochemical quartz crystal microbalance

Pt electrode dissolution has been investigated using an electrochemical quartz crystal microbalance (EQCM) in H₂O₂-containing 0.5 mol dm⁻³ H₂SO₄. The Pt electrode weight-loss of ca. 0.4 μg cm⁻² is observed during nine potential sweeps between 0.01 and 1.36 V vs. RHE. In contrast, the Pt electrode weight-loss is negligible without H₂O₂ (<0.05 μg cm⁻²). To support the EQCM results, the weight-decrease amounts of a Pt disk electrode and amounts of Pt dissolved in the solutions were measured after similar successive potential cycles. As a result, these results agreed well with the EQCM results. Furthermore, the H₂O₂ concentration dependence of the Pt weight-decrease rate was assessed by successive potential steps. These EQCM data indicated that the increase in H₂O₂ accelerates the Pt dissolution. Based on these results, H₂O₂ is known to be a major factor contributing to the Pt dissolution.     

The size and valence state effect of Pt on photocatalytic H2 evolution over platinized TiO2 photocatalyst

Photocatalytic hydrogen production from water or organic compounds is a promising way to resolve our energy crisis and environmental problems in the near future. Over the past decades, many photocatalysts have been developed for solar water splitting. However, most of these photocatalysts require cocatalyst to facilitate H₂ evolution reaction and noble metals as key cocatalysts are widely used. Consequently, the condition of noble metal cocatalyst including the size and valence state etc plays the key role in such photocatalytic system. Here, the size and valence state effect of Pt on photocatalytic H₂ evolution over platinized TiO₂ photocatalyst were studied for the first time. Surprisingly, it was found that Pt particle size does not affect the photoreaction rate with the size range of several nanometers in this work, while it is mainly depended on the valence state of Pt particles. Typically, TOFs of TiO₂ photodeposited with 0.1–0.2 wt% Pt can exceed 3000 h⁻¹.     

Properties and H2 production ability of Pt photodeposited on the anatase phase transition of nitrogen-doped titanium dioxide

The effect of calcination temperature on the properties and H₂ production ability of nitrogen-doped (N-doped) titanium dioxide (TiO₂) photodeposited with 0.2 wt% Pt (platinum) was studied. The increase in crystallinity of pre-calcinated N-doped TiO₂ initiated at temperatures higher than 131 °C transformed the morphology from anomalous nanostructure to texture composed of nanoparticles and enhanced the specific surface areas. At 200-400 °C, the anatase peaks gradually became sharper and the visible light absorption region decreased due to the growth of crystallites and the decrease of N-doping content, respectively. Maximum H₂ production was reached when N-doped TiO₂ was calcined at 200 °C followed by Pt photodeposition. The maximum condition is brought about by the formation of textures consisting of nanoparticles and a broad absorption region, thus creating superior active sites for photocatalytic H₂ production.     

Ag3PO4 photocatalyst: Hydrothermal preparation and enhanced O2 evolution under visible-light irradiation

Visible-light-driven semiconducting photocatalysts of Ag₃PO₄ were prepared by a hydrothermal method, and were optimized by adjusting reaction conditions, i.e., temperature, pH of reaction solution, concentration of feedstock, and time of hydrothermal process. The obtained photocatalysts were then systematically characterized by different instruments, such as XRD, UV–vis, FESEM, and BET, to reveal the physicochemical properties. Furthermore, activities of photocatalysts for visible-light-driven O₂ evolution were evaluated, demonstrating that the photocatalytic activity of Ag₃PO₄ prepared by hydrothermal reaction (initial rate of O₂ evolution, 1156 μmol g⁻¹ h⁻¹) was more than two times as that of sample prepared by room-temperature reaction (initial rate of O₂ evolution, 533 μmol g⁻¹ h⁻¹), which could be attributed to its better ability to utilize visible light and more regulated morphology.     

Effect of H2O2 on Pt electrode dissolution in H2SO4 solution based on electrochemical quartz crystal microbalance study

The effect of H₂O₂ on the Pt dissolution in 0.5 mol dm⁻³ H₂SO₄ was investigated using an electrochemical quartz crystal microbalance (EQCM). For the potential cycling at 50 mV s⁻¹, the Pt weight irreversibly decreases in a N₂ atmosphere with H₂O₂, while only a negligible Pt weight-loss is observed in the N₂ and O₂ atmospheres without H₂O₂. The EQCM data measured by the potential step showed that the Pt dissolution in the presence of H₂O₂ depends on the electrode potential and the H₂O₂ concentration. For the stationary electrolysis, the Pt dissolution occurs at 0.61–1.06 and 1.06–1.36 V vs. RHE. It should be noted that the Pt dissolution phenomenon in the presence of H₂O₂ is also affected by the potential scanning time. Based on these results, H₂O₂ is considered not only to contribute to the formation of Pt-oxide causing the cathodic Pt dissolution, but also to participate in the anodic Pt dissolution and the chemical Pt dissolution.     

Facile fabrication of Bi2O3/TiO2-xNx nanocomposites for excellent visible light driven photocatalytic hydrogen evolution

Mesoporous Bi₂O₃/TiO_2−xN_x nanocomposites (BiNT) were synthesized by soft chemical template free homogeneous co-precipitation technique. XRD, XPS, TEM, UV-Vis DRS and photoluminescence studies were adapted to determine the structural, electronic and optical properties. The photocatalytic activities of the catalysts were evaluated for water splitting to generate clean hydrogen fuel under visible light irradiation (λ ≥ 400 nm). BiNT-400 catalyst showed highest results towards hydrogen production (198.4 μmol/h) with an apparent quantum efficiency of 4.3%. The pronounced activity of BiNT-400 sample towards hydrogen production was well consistent with high crystallinity, large surface area, proper excitation by N doping and Bi₂O₃ sensitization.     

Photocatalytic hydrogen production from aqueous solutions over novel Bi0.5Na0.5TiO3 microspheres

Metal oxide compounds containing bismuth are considered as potential candidates for photocatalysis in both contaminant degradation and H₂ generation, due to the interesting lone electron pairs and the band gap narrowing effect of Bi³⁺. Quaternary perovskite oxide Bi_0.5Na_0.5TiO₃ was thus synthesized at low temperature via a soft chemical route. The influence of alkaline concentrations on the structure, morphology, and optical properties of the samples has been systematically investigated. All samples existed as hierarchical microspheres, which are consisted of cubic nanocrystallines. For the first time, the photocatalytic water splitting for H₂ evolution over Bi_0.5Na_0.5TiO₃ has been studied. A high H₂ evolution rate of 325.4 μmol h⁻¹ g cat⁻¹ under the irradiation of a 500 W xenon lamp was obtained. More importantly, no decrease in the catalytic performance was observed after three consecutive runs of 15 h, suggesting new possibility in designing multi-component photocatalysts for future applications.