H2 and CO production over a stable Ni–MgO–Ce0.8Zr0.2O2 catalyst from CO2 reforming of CH4

Ni–Ce_0.8Zr_0.2O₂ and Ni–MgO–Ce_0.8Zr_0.2O₂ catalysts were investigated for H₂ production from CO₂ reforming of CH₄ reaction at a very high gas hourly space velocity of 480,000 h⁻¹. Ni–MgO–Ce_0.8Zr_0.2O₂ exhibited higher catalytic activity and stability (CH₄ conversion >95% at 800 °C for 200 h). The outstanding catalytic performance is mainly due to the basic nature of MgO and an intimate interaction between Ni and MgO.     

Effects of alumina powder characteristics on H2 and H2O2 production yields in γ-radiolysis of water and 0.4 M H2SO4 aqueous solution

The effects of powder characteristics on H₂ and H₂O₂ productions in ⁶⁰Co γ-radiolysis were studied in pure water and in 0.4 M H₂SO₄ aqueous solutions containing alumina powders. In 0.4 M H₂SO₄ solution, the H₂ yields strongly depended on alumina structures and decreased in the order of α > θ > γ-alumina, although the specific surface areas increased as α < θ < γ. The yields increased with increasing specific surface area when compared among α-alumina. In pure water, similar dependence was observed but not as strong as that for 0.4 M H₂SO₄ solution. The H₂O₂ yields were strongly decreased by adding the alumina powders in both water and 0.4 M H₂SO₄ aqueous solution, although the amounts of decrease were almost neither correlated with specific surface areas nor structures. The enhancing H₂ production was discussed in terms of the electron supply from alumina to aqueous solution as well as the adsorption of OH radicals on alumina surfaces.     

Syngas production by CO2 reforming of coke oven gas over Ni/La2O3–ZrO2 catalysts

Syngas production by CO₂ reforming of coke oven gas (COG) was studied in a fixed-bed reactor over Ni/La₂O₃–ZrO₂ catalysts. The catalysts were prepared by sol–gel technique and tested by XRF, BET, XRD, H₂-TPR, TEM and TG–DSC. The influence of nickel loadings and calcination temperature of the catalysts on reforming reaction was measured. The characterization results revealed that all of the catalysts present excellent resistance to coking. The catalyst with appropriate nickel content and calcination temperature has better dispersion of active metal and higher conversion. It is found that the Ni/La₂O₃–ZrO₂ catalyst with 10 wt% nickel loading provides the best catalytic activity with the conversions of CH₄ and CO₂ both more than 95% at 800 °C under the atmospheric pressure. The Ni/La₂O₃–ZrO₂ catalysts show excellent catalytic performance and anti-carbon property, which will be of great prospects for catalytic CO₂ reforming of COG in the future.     

Characterization and activity test of commercial Ni/Al2O3, Cu/ZnO/Al2O3 and prepared Ni–Cu/Al2O3 catalysts for hydrogen production from methane and methanol fuels

In this study, methane and methanol steam reforming reactions over commercial Ni/Al₂O₃, commercial Cu/ZnO/Al₂O₃ and prepared Ni–Cu/Al₂O₃ catalysts were investigated. Methane and methanol steam reforming reactions catalysts were characterized using various techniques. The results of characterization showed that Cu particles increase the active particle size of Ni (19.3 nm) in Ni–Cu/Al₂O₃ catalyst with respect to the commercial Ni/Al₂O₃ (17.9). On the other hand, Ni improves Cu dispersion in the same catalyst (1.74%) in comparison with commercial Cu/ZnO/Al₂O₃ (0.21%). A comprehensive comparison between these two fuels is established in terms of reaction conditions, fuel conversion, H₂ selectivity, CO₂ and CO selectivity. The prepared catalyst showed low selectivity for CO in both fuels and it was more selective to H₂, with H₂ selectivities of 99% in methane and 89% in methanol reforming reactions. A significant objective is to develop catalysts which can operate at lower temperatures and resist deactivation. Methanol steam reforming is carried out at a much lower temperature than methane steam reforming in prepared and commercial catalyst (275–325 °C). However, methane steam reforming can be carried out at a relatively low temperature on Ni–Cu catalyst (600–650 °C) and at higher temperature in commercial methane reforming catalyst (700–800 °C). Commercial Ni/Al₂O₃ catalyst resulted in high coke formation (28.3% loss in mass) compared to prepared Ni–Cu/Al₂O₃ (8.9%) and commercial Cu/ZnO/Al₂O₃ catalysts (3.5%).     

Oxidative steam reforming of ethanol over Ni/Al2O3 catalysts promoted by CeO2, ZrO2 and CeO2–ZrO2

Oxidative steam reforming of ethanol at low oxygen to ethanol ratios was investigated over nickel catalysts on Al₂O₃ supports that were either unpromoted or promoted with CeO₂, ZrO₂ and CeO₂–ZrO₂. The promoted catalysts showed greater activity and a higher hydrogen yield than the unpromoted catalyst. The characterization of the Ni-based catalysts promoted with CeO₂ and/or ZrO₂ showed that the variations induced in the Al₂O₃ by the addition of CeO₂ and/or ZrO₂ alter the catalyst's properties by enhancing Ni dispersion and reducing Ni particle size. The promoters, especially CeO₂–ZrO₂, improved catalytic activity by increasing the H₂ yield and the CO₂/CO and the H₂/CO values while decreasing coke formation. This results from the addition of ZrO₂ into CeO₂. This promoter highlights the advantages of oxygen storage capacity and of mobile oxygen vacancies that increase the number of surface oxygen species. The addition of oxygen facilitates the reaction by regenerating the surface oxygenation of the promoters and by oxidizing surface carbon species and carbon-containing products.     

Rh promoted and ZrO2/Al2O3 supported Ni/Co based catalysts: High activity for CO2 reforming,steam–CO2 reforming and oxy–CO2 reforming of CH4

Ni (2.5 wt%) and Co (2.5 wt%) supported over ZrO₂/Al₂O₃ were prepared by following a hydrolytic co-precipitation method. The synthesized catalysts were further promoted by Rh incorporation (0.01–1.00 wt%) and tested for their catalytic performance for dry CO₂ reforming, combined steam–CO₂ reforming and oxy–CO₂ reforming of methane for production of syngas. The catalysts were characterized by using N₂ physical adsorption, XRD, H₂–TPR, SEM, CO₂–TPD, NH₃–TPD, TEM and TGA. The results revealed that ZrO₂ phase was in crystalline form in the catalysts along with amorphous Al oxides. Ni and Co were confirmed to be in their respective spinel phases that were reducible to metallic form at 800 °C under H₂. Ni and Co were well dispersed with their nano-crystalline nature. The catalyst with 0.2% loading of Rh showed superior performance in the studied reactions for reforming of methane. This catalyst also showed good coke resistance ability for dry CO₂ reforming reaction with 3.8 wt% of carbon formation during the reaction as compared to 11.6 wt% carbon formation over the catalyst without Rh. The catalyst performance was stable throughout the reaction time for CH₄ conversions, irrespective of carbon formation with slight decline (～1%) in CO₂ conversion. For dry CO₂ reforming reaction, this catalyst showed good conversion for both CH₄ and CO₂ (67.6% and 71.8% respectively) with a H₂/CO ratio of 0.84, while for the Oxy-CO₂ reforming reaction, the activity was superior with CH₄ and CO₂ conversions (73.7% and 83.8% respectively) and H₂/CO ratio of 1.05.     

Hydrogen production by biomass gasification in supercritical water over Ni/γAl2O3 and Ni/CeO2-γAl2O3 catalysts

Hydrogen production by supercritical water gasification (SCWG) is a promising technology for wet biomass utilization. Ni catalyst can realize the high gasification efficiency of biomass near the critical temperature of water. In this paper, Ni/γAl₂O₃ and Ni/CeO₂-γAl₂O₃ catalysts were prepared by an impregnation method. The catalyst performance for glucose gasification in supercritical water was tested in autoclave reactor. All experiments were carried out in the autoclave at 673 K, 24.5 MPa, and the concentration of glucose was 9.09 wt.%. The catalysts before and after reaction were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), BET specific surface area measurements, X-ray fluorescence spectrum (XRF) and Thermo-gravimetric analyses (TGA) in order to investigate on the chemical property and catalytic mechanism. The experimental results showed that hydrogen yield and hydrogen selectivity increased sharply with addition of Ni/γAl₂O₃ and Ni/CeO₂-γAl₂O₃ catalysts. The catalytic activity and H₂ selectivity of Ni/CeO₂-γAl₂O₃ was higher than that of Ni/γ-Al₂O₃ catalyst. The results revealed that carbon deposition and coking led to the deactivation of the catalysts. Ce in the Ni/CeO₂-γAl₂O₃ catalyst had a certain role in the inhibition of carbon deposition and coking.     

Hydrogen production from oxidative steam-reforming of n-propanol over Ni/Y2O3–ZrO2 catalysts

Oxidative steam reforming (OSR) of n-propanol was studied over new Ni catalysts (ca. 7% Ni wt/wt) supported on Y₂O₃–ZrO₂ oxides with different yttrium content (2–41 % Y₂O₃ wt/wt). Materials were characterized by X-ray diffraction, temperature-programmed reduction, X-ray photoelectron and Raman spectroscopy, scanning electron microscopy with energy dispersive X-ray analysis and high resolution transmission electron microscopy. Samples were used in calcined form and tested in the temperature range 673–773 K using a reactant feed of n-propanol/water/O₂ at a molar ratio 1/9/0.5. Hydrogen production is related with the support composition and Ni dispersion.     

Synthesis and characterization of bimetallic Cu–Ni/ZrO2 nanocatalysts: H2 production by oxidative steam reforming of methanol

Cu/ZrO₂, Ni/ZrO₂ and bimetallic Cu–Ni/ZrO₂ catalysts were prepared by deposition–precipitation method to produce hydrogen by oxidative steam reforming of methanol (OSRM) reaction in the range of 250–360 °C. TPR analysis of the Cu–Ni/ZrO₂ catalyst showed that the presence of Cu facilitates the reduction of the Ni at lower temperatures. In addition, this sample showed two reduction peaks, the former peak was attributed to the reduction of the adjacent Cu and Ni atoms which could be forming a bimetallic Cu-rich phase, and the second was assigned to the remaining Ni atoms forming bimetallic Ni-rich nanoparticles. Transmission Electron Microscopy revealed Cu or Ni nanoparticles on the monometallic samples, while bimetallic nanoparticles were identified on the Cu–Ni/ZrO₂ catalyst. On the other hand, Cu–Ni/ZrO₂ catalyst exhibited better catalytic activity than the monometallic samples. The difference between them was related to the Cu–Ni nanoparticles present on the former catalyst, as well as the bifunctional role of the bimetallic phase and the support that improve the catalytic activity. All the catalysts showed the same selectivity toward H₂ at the maximum reaction temperature and it was ∼60%. The high selectivity toward CO is associated to the presence of the bimetallic Ni-rich nanoparticles, as evidenced by TEM–EDX analysis, since this behavior is similar to the one showed by the monometallic Ni-catalyst.     

Syngas production from CH4 dry reforming over Co–Ni/Al2O3 catalyst: Coupled reaction-deactivation kinetic analysis and the effect of O2 co-feeding on H2:CO ratio

The dry and oxidative dry reforming of CH₄ over alumina-supported Co–Ni catalysts were investigated over 72-h longevity experiments. The deactivation behaviour at low CO₂:CH₄ ratio (≤2) suggests that carbon deposition proceeds via a rapid dehydropolymerisation step resulting in the blockage of active sites and loss in CO₂ consumption. In particular, at high temperatures of 923 K and 973 K, a ‘breakthrough’ point was observed in which deactivation that was previously slow suddenly accelerated, indicating rapid polymerisation of deposited carbon. Only with feed CO₂:CH₄ > 2 or with O₂ co-feeding was coke-induced deactivation eliminated. In particular, O₂ co-feeding gave improved carbon removal, product H₂:CO ratios more suitable for downstream GTL processing and stable catalytic performance. Conversion-time data were adequately fitted to the generalised Levenspiel reaction-deactivation model. Activation energy estimate (66–129 kJ mol⁻¹) was dependent on the CO₂:CH₄ ratio but representative of other hydrocarbon reforming reactions on Ni-based catalysts.     

Combustion,performance and emissions of a diesel engine with H2, CH4 and H2–CH4 addition

Experiments were conducted to investigate the combustion and emission characteristics of a diesel engine with addition of hydrogen or methane for dual-fuel operation, and mixtures of hydrogen–methane for tri-fuel operation. The in-cylinder pressure and heat release rate change slightly at low to medium loads but increase dramatically at high load owing to the high combustion temperature and high quantity of pilot diesel fuel which contribute to better combustion of the gaseous fuels. The performance of the engine with tri-fuel operation at 30% load improves with the increase of hydrogen fraction in methane and is always higher than that with dual-fuel operations. Compared with ULSD–CH₄ operation, hydrogen addition in methane contributes to a reduction of CO/CO₂/HC emissions without penalty on NO_x emission. Dual-fuel and tri-fuel operations suppress particle emission to the similar extent. All the gaseous fuels reduce the geometry mean diameter and total number concentration of diesel particulate. Tri-fuel operation with 30% hydrogen addition in methane is observed to be the best fuel in reducing particulate and NO_x emissions at 70 and 90% loads.     

Combination of CO2 reforming and partial oxidation of methane to produce syngas over Ni/SiO2 and Ni–Al2O3/SiO2 catalysts with different precursors

Ni/SiO₂ and Ni–Al₂O₃/SiO₂ catalysts were prepared by incipient wetness impregnation using citrate and nitrate precursors and tested with a reaction of combination of CO₂ reforming and partial oxidation of methane to produce syngas (H₂/CO). The catalytic activity of Ni/SiO₂ and Ni–Al₂O₃/SiO₂ greatly depended on interaction between NiO and support. NiO strongly interacted with support formed small nickel particles (about 4 nm for NiSC which is abbreviation of Ni/SiO₂ prepared with Nickel citrate precursor) after reduction. The small nickel particles over NiSC catalysts exhibited a good catalytic performance.     

Pt-Sn/γ-Al2O3 and Pt-Sn-Na/γ-Al2O3 catalysts for hydrogen production by dehydrogenation of Jet A-1 fuel: Characterisation and preliminary activity tests

The partial dehydrogenation of fuels like diesel or kerosene cuts to produce H₂ is an emerging idea of increasing interest. In the present work the study of the partial dehydrogenation of Jet A-1 fuel on Pt-Sn/γ-Al₂O₃ based catalysts to produce H₂ to feed an on-board (aircraft) proton exchange membrane fuel cell is presented. Extensive physico-chemical characterization of 5% wt.Pt-1% wt.Sn/γ-Al₂O₃ and 5%wt.Pt-1%wt.Sn-1%wt.Na/γ-Al₂O₃ pelleted materials has been performed. A gradient of the active metals from the edge to the centre of the pellet has been observed. A higher concentration of Pt⁰ has been detected on the outer part of the pellet than in the inner part, whereas Sn has been detected only on the external part of the pellet. The investigated materials are active as catalysts for the partial dehydrogenation of normal and desulfurised Jet A-1 kerosene fuel. The presence of sulfur compounds and coke deposition strongly affects the H₂ productivity which decreases rapidly with time on stream. The presence of a Na cation addition contributes to give the highest and most sustained H₂ production. The condensed outlet liquid stream retains the fuel properties in the range of the Jet A-1 kerosene fuel. These are encouraging preliminary results, inviting further research; coking and sulfur poisoning as well as identification of appropriate reaction conditions are the main challenges to be overcome in the immediate future.     

Laminar burning velocities and flame characteristics of CO–H2–CO2–O2 mixtures

Laminar burning velocities of CO–H₂–CO₂–O₂ flames were measured by using the outwardly spherical propagating flame method. The effect of large fraction of hydrogen and CO₂ on flame radiation, chemical reaction, and intrinsic flame instability were investigated. Results show that the laminar burning velocities of CO–H₂–CO₂–O₂ mixtures increase with the increase of hydrogen fraction and decrease with the increase of CO₂ fraction. The effect of hydrogen fraction on laminar burning velocity is weakened with the increase of CO₂ fraction. The Davis et al. syngas mechanism can be used to calculate the syngas oxyfuel combustion at low hydrogen and CO₂ fraction but needs to be revised and validated by additional experimental data for the high hydrogen and CO₂ fraction. The radiation of syngas oxyfuel flame is much stronger than that of syngas–air and hydrocarbons–air flame due to the existence of large amount of CO₂ in the flame. The CO₂ acts as an inhibitor in the reaction process of syngas oxyfuel combustion due to the competition of the reactions of H + O₂ = O + OH, CO + OH = CO₂ + H and H + O₂(+M) = HO₂(+M) on H radical. Flame cellular structure is promoted with the increase of hydrogen fraction and is suppressed with the increase of CO₂ fraction due to the combination effect of hydrodynamic and thermal-diffusive instability.     

H2 production from a single stage water–gas shift reaction over Pt/CeO2, Pt/ZrO2, and Pt/Ce(1−x)Zr(x)O2 catalysts

To develop a single stage water–gas shift reaction (WGS) catalyst for compact reformers, Pt/CeO₂, Pt/ZrO₂, and Pt/Ce_(1−x)Zr_(x)O₂ catalysts have been applied for the target reaction. The CeO₂/ZrO₂ ratio was systematically varied to optimize Pt/Ce_(1−x)Zr_(x)O₂ catalysts. Pt/CeO₂ showed the highest turnover frequency (TOF) and the lowest activation energy (E_a) among the catalysts tested in this study. It has been found that the reduction property of the catalyst is more important than the dispersion for a single stage WGS. Pt/CeO₂ catalyst also showed stable catalytic performance. Thus, Pt/CeO₂ can be a promising catalyst for a single stage WGS for compact reformers.     

Adiabatic burning velocity of H2–O2 mixtures diluted with CO2/N2/Ar

Global warming due to CO₂ emissions has led to the projection of hydrogen as an important fuel for future. A lot of research has been going on to design combustion appliances for hydrogen as fuel. This has necessitated fundamental research on combustion characteristics of hydrogen fuel. In this work, a combination of experiments and computational simulations was employed to study the effects of diluents (CO₂, N₂, and Ar) on the laminar burning velocity of premixed hydrogen/oxygen flames using the heat flux method. The experiments were conducted to measure laminar burning velocity for a range of equivalence ratios at atmospheric pressure and temperature (300 K) with reactant mixtures containing varying concentrations of CO₂, N₂, and Ar as diluents. Measured burning velocities were compared with computed results obtained from one-dimensional laminar premixed flame code PREMIX with detailed chemical kinetics and good agreement was obtained. The effectiveness of diluents in reduction of laminar burning velocity for a given diluent concentration is in the increasing order of argon, nitrogen, carbon dioxide. This may be due to increased capabilities either to quench the reaction zone by increased specific heat or due to reduced transport rates. The lean and stoichiometric H₂/O₂/CO₂ flames with 65% CO₂ dilution exhibited cellular flame structures. Detailed three-dimensional simulation was performed to understand lean H₂/O₂/CO₂ cellular flame structure and cell count from computed flame matched well with the experimental cellular flame.     

O2/CO2和O2/N2氛围下煤粉富氧燃烧数值模拟

在目前煤炭依然作为能源主体的背景下，控制燃煤污染物排放有着重要意义。基于CFD数值模拟，建立伴流燃烧器模型，控制燃料、氧化剂入口流量恒定，设计了O₂/CO₂、O₂/N₂氧化剂氛围中O₂浓度在21%～40%内的多种工况，对煤粉燃烧特性及燃烧产生的污染物进行了研究。分析了不同工况下煤粉燃烧的温度分布、燃烧速率、碳烟、NO_x的生成情况。结果显示，在O₂/CO₂、O₂/N₂两种氧化剂氛围中，随着O₂浓度的上升，煤粉燃烧温度升高、燃烧速率增大，碳烟生成量均增加，同等O2浓度条件下，O₂/CO₂氛围的煤粉燃烧温度和燃烧速率均高于O₂/N₂氛围，碳烟生成量小于O₂/N₂氛围，且O₂/CO₂...     

A novel catalyst–sorbent system for an efficient H2 production with in-situ CO2 capture

This paper presents an experimental investigation for an improved process of sorption-enhanced steam reforming of methane in an admixture fixed bed reactor. A highly active Rh/Ce_αZr_1−αO₂ catalyst and K₂CO₃-promoted hydrotalcite are utilized as novel catalyst/sorbent materials for an efficient H₂ production with in situ CO₂ capture at low temperature (450–500 °C). The process performance is demonstrated in response to temperature (400–500 °C), pressure (1.5–6.0 bar), and steam/carbon ratio (3–6). Thus, direct production of high H₂ purity and fuel conversion >99% is achieved with low level of carbon oxides impurities (<100 ppm). A maximum enhancement of 162% in CH₄ conversion is obtained at a temperature of 450 °C and a pressure of 6 bar using a steam/carbon molar ratio of 4. The high catalyst activity of Rh yields an enhanced CH₄ conversion using much lower catalyst/sorbent bed composition and much smaller reactor size than Ni-based sorption enhanced processes at low temperature. The cyclic stability of the process is demonstrated over a series of 30 sorption/desorption cycles. The sorbent exhibited a stable performance in terms of the CO₂ working sorption capacity and the corresponding CH₄ conversion obtained in the sorption enhanced process. The process showed a good thermal stability in the temperature range of 400–500 °C. The effects of the sorbent regeneration time and the purge stream humidity on the achieved CH₄ conversion are also studied. Using steam purge is beneficial for high degree of CO₂ recovery from the sorbent.     

Hydrogen production from catalytic steam reforming of bio-oil aqueous fraction over Ni/CeO2–ZrO2 catalysts

A series of composite catalysts Ni/CeO₂–ZrO₂ were prepared via impregnation method with Ni as the active metal. A laboratory-scale fixed-bed reactor was employed to investigate the catalyst performance during hydrogen production by steam reforming bio-oil aqueous fraction. Effects of water-to-bio-oil ratio (W/B), reaction temperature, and the loaded weight of Ni and Ce on the hydrogen production performance of Ni/CeO₂–ZrO₂ catalysts were examined. The obtained results were compared with commercial nickel-based catalysts (Z417). The best performance of Ni/CeO₂–ZrO₂ catalyst was observed when the Ni and Ce loaded weight were 12% and 7.5% respectively. At W/B = 4.9, T = 800 °C, H₂ yield reaches the highest of 69.7% and H₂ content of 61.8% were obtained. Under the same condition, H₂ yield and H₂ content were higher than commercial nickel-based catalysts (Z417).     

Hydrogen production from CH4 dry reforming over bimetallic Ni–Co/Al2O3 catalyst

Bimetallic 5%Ni–10%Co/Al₂O₃ catalyst was synthesized using impregnation method and evaluated for methane dry reforming reaction at different reaction temperatures. NiO, Co₃O₄ and spinal metal aluminates, namely, CoAl₂O₄ and NiAl₂O₄ phases were formed on γ-Al₂O₃ support surface during calcination process. 5%Ni–10%Co/Al₂O₃ catalyst exhibited reasonable surface area of 86.93 m² g^?1 with small crystallite dimension of less than 10 nm suggesting that both Co₃O₄ and NiO phases were finely dispersed on the surface of support in agreement with results from scanning electron microscopy (SEM) measurement. Temperature-programmed calcination measurement indicates the complete thermal decomposition and oxidation of metal precursors, viz. Ni(NO₃)₂ and Co(NO₃)₂ to metal oxides and metal aluminates at below 700 K. Both CH₄ and CO₂ conversions were stable over a period of 4 h on-stream and attained an optimum at about 67% and 71%, respectively at 973 K whilst H₂ selectivity and yield were higher than 49%. The ratio of H₂/CO was always less than unity for all runs indicating the presence of reverse water–gas shift reaction. The activation energy for CH₄ and CO₂ consumption was computed as 55.60 and 40.25 kJ mol^?1, correspondingly. SEM micrograph of spent catalyst detected the formation of whisker-like carbon on catalyst surface whilst D and G bands characteristic for the appearance of amorphous and graphitic carbons in this order were observed on surface of used catalyst by Raman spectroscopy analysis. Additionally, the percentage of filamentous carbon was greater than that of graphitic carbon.