Effects of substrate concentration and hydraulic retention time on hydrogen production from common reed by enriched mixed culture in continuous anaerobic bioreactor

This study aims to investigate the effect of substrate concentration and hydraulic retention time (HRT) on hydrogen production in a continuous anaerobic bioreactor from unhydrolyzed common reed (Phragmites australis) an invasive wetland and perennial grass. The bioreactor has capacity of 1 L and working volume of 600 mL. It was operated at pH 5.5, temperature at 37 °C, hydraulic retention time (HRT) 12 h, and variation of substrate concentration from 40, 50, and 60 g COD/L, respectively. Afterward, the HRT was then varied from 12, 8, to 4 h for checking the optimal biohydrogen production. Each condition was run until reach steady state on hydrogen production rate (HPR) which based on hydrogen percentage and daily volume. The results were obtained the peak of substrate concentration was at the 50 g COD/L with HRT 12 h, average HPR and H₂ concentration were 28.71 mL/L/h and 36.29%, respectively. The hydrogen yield was achieved at 106.23 mL H₂/g CODre. The substrate concentration was controlled at 50 g COD/L for the optimal HRT experiments. It was found that the maximum of average HPR and H₂ concentration were 43.28 mL/L/h and 36.96%, respectively peak at HRT 8 h with the corresponding hydrogen yield of 144.35 mL H₂/g CODre. Finally, this study successful produce hydrogen from unhydrolyzed common reed by enriched mixed culture in continuous anaerobic bioreactor.     

Effect of substrate concentration on fermentative hydrogen production from sweet sorghum extract

The aim of the present study was to assess the influence of substrate concentration on the fermentative hydrogen production from sweet sorghum extract, in a continuous stirred tank bioreactor. The reactor was operated at a Hydraulic Retention Time (HRT) of 12 h and carbohydrate concentrations ranging from 9.89 to 20.99 g/L, in glucose equivalents. The maximum hydrogen production rate and yield were obtained at the concentration of 17.50 g carbohydrates/L and were 2.93 ± 0.09 L H₂/L reactor/d and 0.74 ± 0.02 mol H₂/mol glucose consumed, corresponding to 8.81 ± 0.02 L H₂/kg sweet sorghum, respectively. The main metabolic product at all steady states was butyric acid, while ethanol production was high at high substrate concentrations. The experiments showed that hydrogen productivity depends significantly on the initial carbohydrate concentration, which also influences the distribution of the metabolic products.     

Exploring optimal conditions for thermophilic fermentative hydrogen production from cassava stillage

This study investigated the effects of seed sludges, alkalinity and HRT on the thermophilic fermentative hydrogen production from cassava stillage. Five different kinds of sludges were used as inocula without any pretreatment. Though batch experiments showed that mesophilic anaerobic sludge was the best inoculum, the hydrogen yields with different seed sludges were quite similar in continuous experiments in the range of 82.9–92.3 ml H₂/gVS without significant differences which could be attributed to the establishment of Uncultured Thermoanaerobacteriaceae bacterium-dominant microbial communities in all reactors. It is indicated that results obtained from batch experiments are not consistent with those from continuous experiments and all the tested seed sludges are good sources for continuous thermophilic hydrogen production from cassava stillage. The influent alkalinity of 6 g NaHCO₃/L and HRT 24 h were optimal for hydrogen production with hydrogen yield of 76 ml H₂/gVS and hydrogen production rate of 3215 ml H₂/L/d. Butyrate was the predominant metabolite in all experiments. With the increase in alkalinity of more than 6 g/L, the concentration of VFA/ethanol increased while hydrogen yield decreased due to the higher concentration of acetate and propionate. The decrease in HRT resulted in the higher hydrogen production rate but lower hydrogen yield. Variation of hydrogen yields were quite correlated with butyrate/acetate (B/A) ratio with different influent alkalinities, however, butyrate was important parameter to justify the hydrogen yields with various HRTs.     

Enhanced photo-hydrogen production of Rhodopseudomonas faecalis RLD-53 by EDTA addition

This study investigated the effect of EDTA concentration in medium on the growth, hydrogen production and nitrogenase activity of Rhodopseudomonas faecalis RLD-53 by batch cultures. Experimental results indicated that bacterial growth and hydrogen production were strongly inhibited with EDTA concentration increasing to 0.6–0.7 g/L. However, the lag time of hydrogen production and the trends of biomass at EDTA concentration of 0–0.5 g/L were similar. The maximum cumulative hydrogen volume of 3325 ml H₂/L culture, hydrogen production rate of 27.6 ml H₂/L/h and hydrogen yield of 2.97 mol H₂/mol acetate were obtained when EDTA concentration was at 0.3 g/L, and the maximum OD₆₆₀ attained 3.83. And the nitrogenase activity also reached a maximum value of 1331.9 μl-C₂H₄/h/mg dry weight in the medium containing Fe²⁺ and EDTA. These results showed that a proper concentration of EDTA can promote the availability of iron, thereby further enhancing the activity of nitrogenase and photo-hydrogen production.     

Enhancing the performance of dark fermentative hydrogen production using a reduced pressure fermentation strategy

The partial pressure of hydrogen is an extremely important factor for hydrogen generation. This study investigated the effect of reduced pressure (via vacuum) on hydrogen production in a CSTR reactor. The results show that the reduced pressure condition is more effective in enhancing H₂ production at lower HRT (e.g., 8–4 h) than at higher HRT (e.g., 12 h). The optimal hydrogen yield and overall hydrogen production efficiency occurred at a HRT of 6 h with a value of 4.50 mol H₂/mol sucrose and 56.2%, respectively. Meanwhile, at HRT 6 h the hydrogen production rate was 0.937 mol/L/d. In addition, the HPR could be further improved to 1.196 mol/L/d when the HRT was shortened to 4 h, obtaining a 37–271% increase in HPR when compared with that described in the relevant reports. For all experiments, butyrate and acetate were the two primary soluble metabolites, accounting for 85–99% of total soluble microbial products. Predominant production of acetate and butyrate demonstrates the efficient H₂ fermentation with reduced pressure processes.     

Impact of regulated pH on proto scale hydrogen production from xylose by an alkaline tolerant novel bacterial strain, Enterobacter cloacae DT-1

A hydrogen producing facultative anaerobic alkaline tolerant novel bacterial strain was isolated from crude oil contaminated soil and identified as Enterobacter cloacae DT-1 based on 16S rRNA gene sequence analysis. DT-1 strain could utilize various carbon sources; glycerol, CMCellulose, glucose and xylose, which demonstrates that DT-1 has potential for hydrogen generation from renewable wastes. Batch fermentative studies were carried out for optimization of pH and Fe²⁺ concentration. DT-1 could generate hydrogen at wide range of pH (5–10) at 37 °C. Optimum pH was; 8, at which maximum hydrogen was obtained from glucose (32 mmol/L), when used as substrate in BSH medium containing 5 mg/L Fe²⁺ ion. Decrease in hydrogen partial pressure by lowering the total pressure in the fermenter head space, enhanced the hydrogen production performance of DT-1 from 32 mmol H₂/L to 42 mmol H₂/L from glucose and from 19 mmol H₂/L to 33 mmol H₂/L from xylose. Hydrogen yield efficiency (HY) of DT-1 from glucose and xylose was 1.4 mol H₂/mol glucose and 2.2 mol H₂/mol xylose, respectively. Scale up of batch fermentative hydrogen production in proto scale (20 L working volume) at regulated pH, enhanced the HY efficiency of DT-1 from 2.2 to 2.8 mol H₂/mol xylose (1.27 fold increase in HY from laboratory scale). 84% of maximum theoretical possible HY efficiency from xylose was achieved by DT-1. Acetate and ethanol were the major metabolites generated during hydrogen production.     

Hydrogen production from sulfate- and ferrous-enriched wastewater

The quantitative relationship between sulfate reducing bacteria (SRB) and hydrogen (H₂) production from sulfate (SO₄²⁻) and ferrous [Fe(II)] enriched wastewater was investigated. Both Fe(II) (0–11,600 mg/L) and SO₄²⁻ (0–20,000 mg/L) improved the H₂ production efficiency from wastewater. The H₂ yields were increased up to 1.9 mol H₂/mol glucose in 580–1750 mg Fe(II)/L and 1000–3000 mg SO₄²⁻/L enriched wastewater at pH 5.8–6.2. Quantitative Fluorescence In Situ Hybridization (FISH) analyses revealed that the specific sulfate reducing activities (SSRA) were increased from 0.08 and 0.06 to 0.16 and 0.21 g TS/g SRB h in response to variations in sulfate concentration from 300–20,000 mg/L at pH 5.8 and 6.2, respectively. H₂ production was not influenced by low SSRA (≤0.1 g TS/g SRB h), which was independent of pH variation. The results demonstrated that the SSRA and Fe(II) concentration can significantly influence on the biological H₂ production from SO₄²⁻ and Fe(II) containing wastewater.     

The effect of Ni,Fe and Mg concentration on photo-hydrogen production by Rhodopseudomonas faecalis RLD-53

In the present study, the effect of Ni²⁺ (0–10 μmol/l), Fe²⁺ (0–200 μmol/l) and Mg²⁺ (0–15 mmol/l) concentration on photo-hydrogen production from acetate was investigated by batch culture. Results showed that under a proper concentration range, Ni²⁺ was able to enhance the hydrogen production rate and the hydrogen yield; Fe²⁺ was able to increase the hydrogen yield, and hydrogen production rate was enhanced only when the culturing time was 24–72 h. Ni²⁺ and Fe²⁺ at a higher concentration inhibited cell growth. When Ni²⁺ and Fe²⁺ concentrations were 4 μmol/l and 80 μmol/l, respectively, maximal hydrogen yield of 2.87 and 2.78 mol H₂/mol acetate was obtained when batch culturing at 35 °C with initial pH 7.0. Mg²⁺ did not significantly affect hydrogen production and hydrogen yield which maintained at about 2.45 mol H₂/mol acetate, but it was favorable to cell growth.     

The effect of hydraulic retention time on thermophilic dark fermentative biohydrogen production in the continuously operated packed bed bioreactor

The main objective of the study is to investigate the effect of hydraulic retention times on continuous dark fermentative biohydrogen production in an up-flow packed bed reactor (UPBR) containing a novel microorganism immobilization material namely polyester fiber beads. The hydrogen producing dark fermentative microorganisms were obtained by heat-pretreatment of anaerobic sludge from the acidogenic phase of an anaerobic wastewater treatment plant. Glucose was the sole carbon source and the initial concentration was 15 ± 1 g/L throughout the continuous feeding. UPBR was operated under the thermophilic condition at T = 48 ± 2 °C and at varying HRTs between 2 h and 6 h. The hydrogen productivity of continuously operated UPBR increased with increasing HRT. Hydrogen production volume varied between 4331 and 6624 ml/d, volumetric hydrogen production rates (VHPR) were obtained as 3.09–4.73 L H₂/L day, and hydrogen production yields (HY) were 0.49 mol/mol glucose-0.89 mol/mol glucose depending on HRT. Maximum daily hydrogen volume (6624 ml/d), the yield (0.89 mol/mol glucose) and VHPR (4.73 L H₂/L day) were obtained at HRT = 6 h. The production rate and the yield decreased with increasing organic loading rate due to substrate inhibition.     

Simultaneous thermophilic hydrogen production and phenol removal from palm oil mill effluent by Thermoanaerobacterium-rich sludge

Thermoanaerobacterium-rich sludge was used for hydrogen production and phenol removal from palm oil mill effluent (POME) in the presence of phenol concentration of 100–1000 mg/L. Thermoanaerobacterium-rich sludge yielded the most hydrogen of 4.2 L H₂/L-POME with 65% phenol removal efficiency at 400 mg/L phenol. Butyric acid and acetic acid were the main metabolites. The effects of oil palm ash, NH₄NO₃ and iron concentration (Fe²⁺) on hydrogen production and phenol removal efficiency from POME by Thermoanaerobacterium-rich sludge was investigated using response surface methodology (RSM). The RSM results indicated that the presence of 0.2 g Fe²⁺/L, 0.3 g/L NH₄NO₃ and 20 g/L oil palm ash in POME could improved phenol removal efficiency, with predicted hydrogen production and phenol removal efficiency of 3.45 L H₂/L-POME and 93%, respectively. In a confirmation experiment under optimized conditions highly reproducible results were obtained, with hydrogen production and phenol removal efficiency of 3.43 ± 0.12 L H₂/L-POME and 92 ± 1.5%, respectively. Simultaneous hydrogen production and phenol removal efficiency in continuous stirred tank reactor at hydraulic retention time (HRT) of 1 and 2 days were 4.0 L H₂/L-POME with 85% and 4.2 L H₂/L-POME with 92%, respectively. Phenol degrading Thermoanaerobacterium-rich sludge comprised of Thermoanaerobacterium thermosaccharolyticum, Thermoanaerobacterium aciditolerans, Desulfotomaculum sp., Bacillus coagulans and Clostridium uzonii. Phenol degrading Thermoanaerobacterium-rich sludge has great potential to harvest hydrogen from phenol-containing wastewater.     

Continuous hydrogen production from tofu processing waste using anaerobic mixed microflora under thermophilic conditions

We carried out continuous fermentative H₂ production from tofu (soybean curd)-processing waste (TPW) using anaerobic mixed microflora under thermophilic (60 °C) conditions and compared the rates and yields of H₂ production in a continuous stirred-tank reactor (CSTR) and a membrane bioreactor (MBR), wherein the membrane filtration unit was coupled to the CSTR. The TPW was diluted with tap water and then hydrolyzed by blending for 5 min in the presence of 0.5% HCl, and it was found that this protocol significantly increased the amount of soluble material in the mixture. The soluble chemical oxygen demand (SCOD)-to-total COD (TCOD) ratio jumped from 14% to 60%, and the soluble carbohydrate concentration was increased threefold, from 2.4 g/L to 7.2 g/L. Accordingly, H₂ production potential was increased 2.8-fold. In a CSTR operation using pretreated TPW as the substrate, a stable volumetric H₂ production rate (VHPR) of 8.17 ± 0.32 L H₂/L/d and a H₂ yield of 1.20 ± 0.05 mol H₂/mol hexose_added at 8-h HRT were achieved. Substantial increases in the VHPR and H₂ yield over those obtained with the CSTR were observed in the MBR operation. The role of the MBR was to increase the retention time of the solid substrate and the concentration of microorganisms, thereby enhancing the substrate utilization rate for H₂ production. Acetic and butyric acids were the main liquid-state metabolites produced during the fermentation process, thus indicating that the thermophilic operation provided favorable conditions for H₂ production from TPW. A maximum H₂ yield of 1.87 mol H₂/mol hexose_added was achieved at 8-h HRT and then gradually decreased to 1.00 mol H₂/mol hexose-equivalent at 2-h HRT. Meanwhile, the VHPR continuously increased to a maximum of 19.86 L H₂/L/d at 4-h HRT and then decreased with a high dilution rate as the HRT was lowered to 2 h (minimum). At 2-h HRT, the degradation of soluble carbohydrate was limited.     

HRT control as a strategy to enhance continuous hydrogen production from sugarcane juice under mesophilic and thermophilic conditions in AFBRs

The objective of this study was to evaluate the effects of hydraulic retention time (HRT) (8–1 h) on H₂ production from sugarcane juice (5000 mg COD L⁻¹) in mesophilic (30 °C, AFBR-30) and thermophilic (55 °C, AFBR-55) anaerobic fluidized bed reactors (AFBRs). At HRTs of 8 and 1 h in AFBR-30, the H₂ production rates were 60 and 116 mL H₂ h⁻¹ L⁻¹, the hydrogen yields were 0.60 and 0.10 mol H₂ mol⁻¹ hexose, and the highest bacterial diversities were 2.47 and 2.34, respectively. In AFBR-55, the decrease in the HRT from 8 to 1 h increased the hydrogen production rate to 501 mL H₂ h⁻¹ L⁻¹ at the HRT of 1 h. The maximum hydrogen yield of 1.52 mol H₂ mol⁻¹ hexose was observed at the HRT of 2 h and was associated with the lowest bacterial diversity (0.92) and highest bacterial dominance (0.52).     

Direct fermentation of Laminaria japonica for biohydrogen production by anaerobic mixed cultures

A few studies have been made on fermentative hydrogen production from marine algae, despite of their advantages compared with other biomass substrates. In this study, fermentative hydrogen production from Laminaria japonica (one brown algae species) was investigated under mesophilic condition (35 ± 1 °C) without any pretreatment method. A feasibility test was first conducted through a series of batch cultivations, and 0.92 mol H₂/mol hexose_added, or 71.4 ml H₂/g TS of hydrogen yield was achieved at a substrate concentration of 20 g COD/L (based on carbohydrate), initial pH of 7.5, and cultivation pH of 5.5. Continuous operation for a period of 80 days was then carried out using anaerobic sequencing batch reactor (ASBR) with a hydraulic retention time (HRT) of 6 days. After operation for approximately 30 days, a stable hydrogen yield of 0.79 ± 0.03 mol H₂/mol hexose_added was obtained. To optimize bioenergy recovery from L. japonica, an up-flow anaerobic sludge blanket reactor (UASBr) was applied to treat hydrogen fermentation effluent (HFE) for methane production. A maximum methane yield of 309 ± 12 ml CH₄/g COD was achieved during the 90 days operation period, where the organic loading rate (OLR) was 3.5 g COD/L/d.     

Thermophilic hydrogen and methane production from sugarcane stillage in two-stage anaerobic fluidized bed reactors

This study evaluated the feasibility of H₂ and CH₄ production in two-stage thermophilic (55 °C) anaerobic digestion of sugarcane stillage (5,000 to 10,000 mg COD.L⁻¹) using an acidogenic anaerobic fluidized bed reactor (AFBR-A) with a hydraulic retention time (HRT) of 4 h and a methanogenic AFBR (AFBR-S) with HRTs of 24 h–10 h. To compare two-stage digestion with single-stage digestion, a third methanogenic reactor (AFBR-M) with a HRT of 24 h was fed with increasing stillage concentrations (5,000 to 10,000 mg COD.L⁻¹). The AFBR-M produced a methane content of 68.4 ± 7.2%, a maximum yield of 0.30 ± 0.04 L CH₄.g COD⁻¹, a production rate of 3.78 ± 0.40 L CH₄.day⁻¹.L⁻¹ and a COD removal of 73.2 ± 5.0% at an organic loading rate (OLR) of 7.5 kg COD.m⁻³.day⁻¹. In contrast, the two-stage AFBR-A system produced a hydrogen content of 23.9 ± 5.6%, a production rate of 1.30 ± 0.16 L H₂.day⁻¹.L⁻¹ and a yield of 0.34 ± 0.08 mmol H₂.g CODap⁻¹. Additionally, the decrease in the HRT from 18 h to 10 h in the AFBR-S favored a higher methane production, improving the maximum methane content (74.5 ± 6.0%), production rate (5.57 ± 0.38 L CH₄.day⁻¹.L⁻¹) and yield (0.26 ± 0.06 L CH₄.g COD⁻¹) at an OLR of 21.6 kg COD.m⁻³.day⁻¹ (HRT of 10 h) with a total COD removal of 70.1 ± 7.1%. Under the applied COD of 10,000 mg L⁻¹, the two-stage system showed a 52.8% higher energy yield than the single-stage anaerobic digestion system. These results show that, relative to a single-stage system, two-stage anaerobic digestion systems produce more hydrogen and methane while achieving similar treatment efficiencies.     

Evaluation of feeding strategies in upflow anaerobic sludge bed reactor for hydrogenogenesis at psychrophilic temperature

The present work evaluated the biohydrogen production from a 0.4 L upflow anaerobic sludge blanket reactor type (UASB) operating at psychrophilic temperature (21 ± 2 °C) at different feeding strategies varying hydraulic retention times (HRT) and sucrose concentration in the feeding. First strategy (24 h/31c) fed semi-continuously 31 g_sucrose L⁻¹ at 24 h HRT; second strategy (12 h/19c) fed semi-continuously 19 g_sucrose L⁻¹ at 12 h HRT; third strategy (4 h/8c) fed continuously 8.3 g_sucrose L⁻¹ at 4 h HRT.After 70 days of operation, the UASB accumulated 65.44 L H₂. The average HY for the whole operation during the three strategies was 62.6 NmL H₂ g_sucrose⁻¹, and average hydrogen content was 69.04%. In general terms, the best operation strategy was 12 h/19c since it presented good set of results, the best HY (70.6 NmL H₂ g_sucrose⁻¹) and a comparable hydrogen production rate (2.6 L (L d)⁻¹) to that obtained in 4 h/8c strategy (3.17 L (L d)⁻¹). The average gross energy potential rate from the 12 h/19c strategy was 46.21 kJ (L d)⁻¹, whereas energy heating losses were circumvented due to operation at psychrophilic regime. Indeed, psychrophilic or room temperatures should be broadly regarded as an effective alternative towards net energy gains in biohydrogen production.     

Fermentative hydrogen production by a new mesophilic bacterium Clostridium sp. 6A-5 isolated from the sludge of a sugar mill

The fermentative hydrogen production capability of the newly isolated Clostridium sp. 6A-5 bacterium was studied in a batch cultivation experiment. Various culture conditions (temperature, initial pH, and glucose concentration) were evaluated for their effects on cell growth and hydrogen production (including the yield and rate) of Clostridium sp. 6A-5. Optimal cell growth was observed at 40 °C, initial pH 7.5–8, and glucose concentration 16–26 g/L. The optimal hydrogen yield was obtained at 43 °C, initial pH 8, and glucose concentration 10–16 g/L. Hydrogen began to evolve when cell growth entered the mid-exponential phase and reached the maximum production rate at the late exponential and stationary phases. The maximum hydrogen yield, and rate were 2727 mL/L, and 269.3 mL H₂/L h, respectively. These results indicate that Clostridium sp. 6A-5 is a good candidate for mesophilic fermentative hydrogen production.     

Application of immobilized upflow anaerobic sludge blanket reactor using Clostridium LS2 for enhanced biohydrogen production and treatment efficiency of palm oil mill effluent

Polyethylene glycol (PEG) gel was used to immobilize hydrogen producing Clostridium LS2 bacteria for hydrogen production in an upflow anaerobic sludge blanket (UASB) reactor. The UASB reactor with a PEG-immobilized cell packing ratio of 10% weight to volume ratio (w/v) was optimal for dark hydrogen production. The performance of the UASB reactor fed with palm oil mill effluent (POME) as a carbon source was examined under various hydraulic retention time (HRT) and POME concentration. The best volumetric hydrogen production rate of 365 mL H₂/L/h (or 16.2 mmol/L/h) with a hydrogen yield of 0.38 L H₂/g COD_added was obtained at POME concentration of 30 g COD/L and HRT of 16 h. The average hydrogen content of biogas and COD reduction were 68% and 65%, respectively. The primary soluble metabolites were butyric acid and acetic acid with smaller quantities of other volatile fatty acid and alcohols formed during hydrogen fermentation. More importantly, the feasibility of PEG-immobilized cell UASB reactor for the enhancement of the dark-hydrogen production and treatment of wastewater is demonstrated.     

Dark fermentation of acid hydrolyzed ground wheat starch for bio-hydrogen production by periodic feeding and effluent removal

Dark fermentation of acid hydrolyzed ground wheat starch for bio-hydrogen production by periodic feeding and effluent removal was investigated at different feeding intervals. Ground wheat was acid hydrolyzed at pH = 3 and T = 121 °C for 30 min using an autoclave. The resulting sugar solution was subjected to dark fermentation with periodic feeding and effluent removal. The feed solution contained 9 ± 0.5 g L⁻¹ total sugar supplemented with some nutrients. Depending on the feeding intervals hydraulic residence time (HRT) was varied between 6 and 60 h. Steady-state daily hydrogen production increased with decreasing HRT. The highest daily hydrogen production (305 ml d⁻¹) and volumetric hydrogen production rate (1220 ml H₂ L⁻¹ d⁻¹) were obtained at HRT of 6 h. Hydrogen yield (130 ml H₂ g⁻¹ total sugar) reached the highest level at HRT = 24 h. Effluent total sugar concentration decreased, biomass concentration and yield increased with increasing HRT indicating more effective sugar fermentation at high HRTs. Dark fermentation end product profile shifted from acetic to butyric acid with increasing HRT. High acetic/butyric acid ratio obtained at low HRTs resulted in high hydrogen yields.     

Biological hydrogen production in an anaerobic sequencing batch reactor: pH and cyclic duration effects

An anaerobic sequencing batch reactor (ASBR) was used to evaluate biological hydrogen production from carbohydrate-rich organic wastes. The goal of the proposed project was to investigate the effects of pH (4.9, 5.5, 6.1, and 6.7), and cyclic duration (4, 6, and 8 h) on hydrogen production. With the ASBR operated at 16-h HRT, 25 g COD/L, and 4-h cyclic duration, the results showed that the maximum hydrogen yield of 2.53 mol H₂/mol sucrose_consumed appeared at pH 4.9. The carbohydrate removal efficiency declined to 56% at pH 4.9, which indirectly resulted in the reduction of total volatile fatty acid production. Acetate fermentation was the dominant metabolic pathway at pH 4.9. The concentration of mixed liquor volatile suspended solid (MLVSS) also showed a decrease from nearly 15,000 mg/L between pHs 6.1 and 6.7 to 6000 mg/L at pH 4.9. Investigation of the effect of cyclic duration found that hydrogen yield reached the maximum of 1.86 mol H₂/mol sucrose_consumed at 4-h cyclic duration while ASBR was operating at 16-h HRT, 15 g COD/L, and pH 4.9. The experimental results showed that MLVSS concentration increased from 6200 mg/L at 4-h cyclic duration to 8500 mg/L at 8-h cyclic duration. However, there was no significant change in effluent volatile suspended solid concentration. The results of butyrate to acetate ratio showed that using this ratio to correlate the performance of hydrogen production is not appropriate due to the growth of homoacetogens. In ASBR, the operation is subject to four different phases of each cycle, and only the complete mix condition can be achieved at react phase. The pH and cyclic duration under the unique operations profoundly impact fermentative hydrogen production.     

An anaerobic sequential batch reactor for enhanced continuous hydrogen production from fungal pretreated cornstalk hydrolysate

Anaerobic sequencing batch reactor (ASBR) process offers great potential for H₂ production from wastewaters. In this study, an ASBR was used at first time for enhanced continuous H₂ production from fungal pretreated cornstalk hydrolysate by Thermoanaerobacterium thermosaccharolyticum W16. The reactor was operated at different hydraulic retention times (HRTs) of 6, 12, 18, and 24 h by keeping the influent hydrolysate constant at 65 mmol sugars L⁻¹. Results showed that increasing the HRT from 6 to 12 h led to the H₂ production rate increased from 6.7 to the maximum of 9.6 mmol H₂ L⁻¹ h⁻¹ and the substrate conversion reached 90.3%, although the H₂ yield remained at the same level of 1.7 mol H₂ mol⁻¹ substrate. Taking into account both H₂ production and substrate utilization efficiencies, the optimum HRT for continuous H₂ production via an ASBR was determined at 12 h. Compared with other continuous H₂ production processes, ASBR yield higher H₂ production at relatively lower HRT. ASBR is shown to be another promising process for continuous fermentative H₂ production from lignocellulosic biomass.