(1-x)Na0.5Bi4.5Ti4O15-xBaTiO3高温铋层状陶瓷的结构与性能研究

采用固相法制备(1-x) N0.5Bi4.5Ti4O15-xBaTiO3 (NBT-BT,x=0,0.05,0.10,0.20,0.30,0.40)高温铋层状压电陶瓷材料.用X射线衍射(XRD)、SEM扫描电镜(SEM),介电和阻抗温谱等测试方法研究了BaTiO3掺杂量对Na0.5Bi4.5Ti4O15陶瓷晶体结构和电...     

Co、Mn共掺杂铋层状Na_(0.5)Bi_(4.5)Ti_4O_(15)无铅压电陶瓷的显微结构及电性能

采用固相法制备Na0.5Bi4.5Ti4O15+x%Co2O3+y%MnCO3(NBT-CM-x)(y=0.1x)铋层状无铅压电陶瓷,研究了Co、Mn共掺杂对Na0.5Bi4.5Ti4O15陶瓷显微结构和电性能的影响。结果表明:所有样品均为铋层状结构;Co、Mn共掺杂能促进陶瓷晶粒生长;随Co、Mn共掺杂量的增加,Curie温度TC逐渐升高(均在635℃以上);Cole-Cole图出现2个圆弧,表明存在晶粒和晶界效应;适量Co、Mn共掺杂提高了Na0.5Bi4.5Ti4O15陶瓷的压电常数d33、剩余极化强度Pr、机械品质因数Qm和相对介电常数εr,降低了直流电导率σDC和介电损耗tanδ。当x=3.0时,NBT-CM-x陶瓷的综合性能最佳:d33=24pC/N,Pr=11.70μC/cm2,Qm=3 117,εr=198,tanδ=0.19%,kp=9.9%,kt=14.7%,表明该陶瓷材料具有良好的高温应用前景。     

Ti不足对Na_（0.5）Bi_（4.5）Ti_（4-x）O_（15）陶瓷性能的影响

用传统固相烧结工艺制备致密Na0.5Bi4.5Ti4-xO15（x=0,0.02,0.04,0.06,0.08）系列铋层结构压电陶瓷,研究该系列陶瓷的微观结构、介电性质和压电性质。结果表明：少量Ti不足可以促进Na0.5Bi4.5Ti4O15陶瓷晶粒长大并使陶瓷的压电性能获得较大提高;随着x增大,陶瓷的压电常数和机电耦...     

水热法制备钛酸铋钠无铅压电陶瓷粉体

以Bi(NO3)3·5H2O和纳米级Ti O2分别作为铋源和钛源,Na OH作为钠源和矿化剂,采用水热法制备钛酸铋钠无铅压电陶瓷粉体,(Na,Bi)Ti O3(NBT)粉体,并对样品进行了XRD和SEM表征。结果表明,水热反应温度为200℃时保温6 h,Na OH浓度为6 mol/L时,可制得结晶完全的立方相NBT,粉体呈球形,粒径约为1μm。水热反应温度、矿化剂浓度和反应时间的增加能促使晶化反应的进行和晶粒长大。     

钛酸铋陶瓷靶材的热压烧结

纯相、高致密度、结晶良好的陶瓷靶材是物理气相沉积薄膜的前提.采用热压烧结方法制备钛酸铋(Bi4Ti3O12)陶瓷靶材,重点研究了制备工艺对靶材的物相、微观结构和致密度的影响.以Bi2O3和TiO2微粉为原料,采用固相反应法,在800℃合成出纯相的Bi4Ti3O12粉体;加入过量3wt%的Bi2O3,可以有效防止烧结过程中因Bi挥发所产生的杂相,得到纯相的Bi4Ti3O12陶瓷;采用热压烧结方法,进一步实现了Bi4Ti3O12粉体的致密烧结,确定了适宜的制备条件为850℃,30MPa,2b,在该条件下制备的Bi4Ti3O12陶瓷致密度达到99%,晶粒呈片层状,大小约2-4μm,可满足靶材制备薄膜的需求.     

常压溶剂热法制备Bi0.5Na0.5TiO3纳米粉体的研究

以Bi(NO3)3·5H2O、Ti(OC4H9)4为原料,无水乙醇作溶剂,采用溶剂热法在常压下合成了Bi0.5Na0.5TiO3(简称为BNT)纳米粉体.通过X射线衍射(XRD)和扫描电子显微镜(SEM)对BNT粉体进行了表征.并在常压溶剂热条件下研究了影响BNT晶体生长和形貌的主要因素.实验结果表明:反应温度为100 ℃,保温时间为2.5 h,NaOH浓度为12 mol·L-1,650 ℃下煅烧2 h时,能制备出单一的BNT粉体,且制得粉体的粒径尺寸约为100 nm.     

片状Bi4Ti3O12的合成及表征

采用熔盐法制备了Bi4Ti3O12粉体,研究了煅烧温度和盐的加入量对粉体显微形貌的影响.结果表明:Bi4Ti3O12晶粒呈较规则的薄片状四边形;烧温度的升高,晶粒尺寸显著增大,a-b面取向生长明显;盐与反应原料的质量比为1:1时,晶粒尺寸分布均匀,为6～8μm;晶粒生长遵循Ostwald熟化机理.     

模板前驱体对熔盐法制备Na_(0.5)Bi_(0.5)TiO_3片状晶粒的影响

首先采用熔盐法合成出铋层状结构的Bi_4Ti_3O_(12)和Na_(0.5)Bi_(4.5)Ti_4O_(15)籽晶,再分别以其作为前驱体,通过拓扑化学反应在900～1100℃合成了片状、各向异性的Na_(0.5)Bi_(0.5)TiO_3晶粒。通过XRD,SEM分析方法,研究了模板前驱体对Na_(0.5)Bi_(0.5)TiO_3晶粒相结构和微观形貌的影响,并讨论了其形成机理。结果表明:前驱体晶胞的不同造成Na_(0.5)Bi_(0.5)TiO_3粒径大小和形貌的差异。     

溶胶-凝胶法合成(Na0.5Bi0.5)TiO3微粉

以钛酸四丁酯、硝酸铋、醋酸钠和冰醋酸为原料,利用溶胶-凝胶工艺得到透明凝胶,经干燥后煅烧成(Na0.5Bi0.5)TiO3微粉。通过对溶胶体系水/醇盐的摩尔比、初始pH值及胶凝温度对(Na0.5Bi0.5)TiO3凝胶体系溶胶-凝胶形成过程影响的研究,发现水/醇盐比R在35≤R≤60,pH在2.2~3.5,反应温度在40~60℃时,能够得到透明的溶胶;通过TG-DTA、SEM、X-ray等分析手段对(Na0.5Bi0.5)TiO3粉体进行测试,表明在650℃合成1h可以得到单一钙钛矿(Na0.5Bi0.5)TiO3晶体;采用TEM对(Na0.5Bi0.5)TiO3干凝胶粉体分析其粒径大小约为10nm。     

水热法制备(Na0.82K0.18)0.5Bi0.5TiO3陶瓷粉体及其介电性能研究

以NaNO3,KNO3,Bi(NO3)3·5H2O和Ti(OC4H9)4为原料,NaOH为矿化剂,采用水热法成功制备了(Na0.82K0.18)0.5Bi0.5TiO3 (NKBT)粉体.研究了反应温度、反应时间和NaOH浓度对NKBT粉体制备的影响.运用XRD、SEM对制备的NKBT粉体进行了测试.测试结果显示,通过调整水热反应条件可对NKBT粉体的微观形貌进行控制.采用传统烧结法可将水热法制备的NKBT粉体烧结为致密的NKBT陶瓷.     

Piezoelectric K0.5Na0.5NbO3 Ceramics Textured Using Needlelike K0.5Na0.5NbO3 Templates

Improved performance by texturing has become attractive in the field of lead‐free ferroelectrics, but the effect depends heavily on the degree of texture, type of preferred orientation, and whether the material is a rotator or extender ferroelectric. Here, we report on successful texturing of K_0.5Na_0.5NbO₃ (KNN) ceramics by alignment of needlelike KNN templates in a matrix of KNN powder using tape casting. Homotemplated grain growth of the needles was confirmed during sintering, resulting in a high degree of texture parallel to the tape casting direction (TCD) and the aligned needles. The texture significantly improved the piezoelectric response parallel to the tape cast direction, corresponding to the direction of the strongest <001>_pc orientation, while the response normal to the tape cast plane was lower than for a nontextured KNN. In situ X‐ray diffraction during electric field application revealed that non‐180° domain reorientation was enhanced by an order of magnitude in the TCD, compared to the direction normal to the tape cast plane and in the nontextured ceramic. The effect of texture in KNN is discussed with respect to possible rotator ferroelectric properties of KNN.     

四元复合氧化物La_(0.5)Sr_(0.5)Ni_(0.5)Cu_(0.5)O_3的抗硫性能

以SO2 为毒物 ,采用脉冲中毒方法 ,再以CO氧化反应为探针 ,对三元复合氧化物催化剂La0 .5Sr0 .5NiO3 与La0 .5Sr0 .5CuO3 以及四元复合氧化物催化剂La0 .5Sr0 .5Ni0 .5Cu0 .5O3 等三种催化剂样品的抗硫毒能力、失活曲线、中毒催化剂的再生性能以及毒物残留形态等进行了全面考察和对比分析。实验结果表明四元复合氧化物催化剂La0 .5Sr0 .5Ni0 .5Cu0 .5O3 在SO2 毒物含量是 1 2 2×10 -2 mmol时 ,特别是在高温 (≥ 30 0℃ )条件下 ,具有优异的抗硫性能     

Thermally-stable large strain in Bi(Mn0.5Ti0.5)O3 modified 0.8Bi0.5Na0.5TiO3-0.2Bi0.5K0.5TiO3 ceramics

(1-x)[0.8Bi_0.5Na_0.5TiO₃-0.2Bi_0.5K_0.5TiO₃]-xBi(Mn_0.5Ti_0.5)O₃ (x = 0–0.06, BNKMT100x) lead-free ferroelectric ceramics were prepared via solid state reaction method. Bi(Mn_0.5Ti_0.5)O₃ induces a structure transition from rhombohedral-tetragonal morphotropic phases to pseudo-cubic phase. Moreover, the wide range of compositions within x = 0.03–0.055 exhibit large strain of 0.31%–0.41% and electrostrictive coefficient of 0.027–0.041 m⁴/C². Especially, at x = 0.04, the large strain and electrostrictive coefficient are nearly temperature-independent in the range of 25–100 °C. The impedance analysis shows the large strain and electrostrictive coefficient originate from polar nanoregions response due to the addition of Bi(Mn_0.5Ti_0.5)O₃.     

Na0.5Bi0.5TiO3-Ba0.5Sr0.5Nb2O6无铅压电陶瓷的研究

采用固相法制备了(1-x)(Na0.5Bi0.5)TiO3-xBa0.5Sr0.5Nb2O6(0≤x≤1.0％)(简称(1-x)NBT-xBSN)无铅压电陶瓷,研究了不同BSN含量(x=0,0.1％,0.3％,0.5％,0.7％,1.0％,摩尔分数)样品的物相组成、显微结构及电性能.结果表明:所有样品均为纯钙钛矿结构,随掺杂量x的增加,陶瓷的相对密度pr、压电常数d33和机电耦合系数kp均先增大后降低,机械品质因子Qm和退极化温度Td则逐渐下降.该体系陶瓷具有弥散相变特征,弥散指数介于1.6～1.7.当x=0.5％时,陶瓷获得最佳性能:d33=92pC/N,kp=0.164,Qm=89,εr=650,tanδ=5.47％,pr=96.5％.     

Near-infrared emitting CdTe0.5Se0.5/Cd0.5Zn0.5S quantum dots: synthesis and bright luminescence

We present how CdTe_0.5Se_0.5 cores can be coated with Cd_0.5Zn_0.5S shells at relatively low temperature (around 200°C) via facile synthesis using organic ammine ligands. The cores were firstly fabricated via a less toxic procedure using CdO, trioctylphosphine (TOP), Se, Te, and trioctylamine. The cores with small sizes (3.2-3.5 nm) revealed green and yellow photoluminescence (PL) and spherical morphologies. Hydrophobic core/shell CdTe_0.5Se_0.5/Cd_0.5Zn_0.5S quantum dots (QDs) with tunable PL between green and near-infrared (a maximum PL peak wavelength of 735 nm) were then created through a facile shell coating procedure using trioctylphosphine selenium with cadmium and zinc acetate. The QDs exhibited high PL efficiencies up to 50% because of the formation of a protective Cd_0.5Zn_0.5S shell on the CdTe_0.5Se_0.5 core, even though the PL efficiency of the cores is low (≤1%). Namely, the slow growth process of the shell plays an important role for getting high PL efficiencies. The properties of the QDs are largely determined by the properties of CdTe_0.5Se_0.5 cores and shells preparation conditions such as reaction temperature and time. The core/shell QDs exhibited a small size diameter. For example, the average diameter of the QDs with a PL peak wavelength of 735 nm is 6.1 nm. Small size and tunable bright PL makes the QDs utilizable as bioprobes because the size of QD-based bioprobes is considered as the major limitation for their broad applications in biological imaging.     

K0.5Na0.5NbO3-BaCu0.5W0.5O3无铅压电陶瓷的结构与性能

以传统固相法工艺制备(1-x)K0.5Na0.5NbO3-xBaCu0.5W0.5O3[(1-x)KNN-xBCW]无铅压电陶瓷,研究不同BCW掺量(x=0％,0.1％,0.25％,0.5％,1.0％,摩尔分数,下同)对KNN陶瓷的晶体结构和电性能的影响,结果表明:x＜0.5％时,KNN陶瓷的相结构没有改变,仍为正交相...     

Na0.5Bi0.5TiO3-K0.5Bi0.5TiO3系无铅压电陶瓷的极化工艺研究

主要研究了极化电场,极化时间和极化温度等工艺参数对Na0.5Bi0.5TiO3-K0.5Bi0.5TiO3系无铅压电陶瓷介电和压电性能的影响。结果表明:极化电场和极化温度对压电陶瓷的介电、压电性能影响较大,而极化时间则影响较小。适宜的极化电场是3～3.5kV/mm,极化温度70～80℃,极化时间为10～15min。     

CeO2掺杂钛酸铋钠钾陶瓷的制备工艺与介电性能

为了进一步探索合成工艺对钛酸铋钠系无铅材料的结构及介电特性的影响,本文以甘氨酸为燃料,利用固相-燃烧法制备了CeO2掺杂的Bi0.5Na0.5TiO3-Bi0.5K0.5TiO3 (BNKT)陶瓷.XRD表明,在固相合成工艺中引入燃烧法制备BNKT陶瓷,比传统固相法降低预烧温度150 ℃,掺杂的CeO2扩散进入了BNKT钙钛矿的晶格,且当掺杂量为0%~0.3%时,形成纯的钙钛矿相结构;SEM表明,CeO2掺杂使晶粒尺寸趋于平均,对晶粒生长有抑制作用;介电温谱表明,随着CeO2掺杂量增加,介电常数εr和退极化温度Td、相转变温度Tm降低,介电反常峰逐渐弱化,且室温至300 ℃,介电损耗tanδ始终在0.3%以下,并从微结构缺陷空位形成机制角度,结合铁电畴壁运动状态,分析讨论了对材料介电特性的作用规律.     

Raman spectroscopy of Na0.5Bi0.5TiO3

We have measured the Raman spectra of bismuth sodium titanate in its rhombohedral, tetragonal, and cubic phases, with special attention paid to the phase transitions at 584K and 837K (heating). Both transitions appear to be order-disorder and strongly first order, with large thermal hysteresis. The phonon spectra at temperature slightly below the tetragonal phase are remarkably similar to BaTiO₃ with A₁(To) modes at 130, 269, and 541 cm^-1 (compared with 170, 270, 520 cm^-1 in BaTiO₃) and an E(TO) at 52 cm^-1.     

Characterization of multiferroic PbFe0.5Nb0.5O3 and PbFe0.5Ta0.5O3 ceramics derived from citrate polymeric precursors

Ceramics of the perovskite multiferroics PbFe_0.5Nb_0.5O₃ (PFN) and PbFe_0.5Ta_0.5O₃ (PFT) were synthesized from new citrate polymeric precursors. X-ray tests pointed to trace amounts of the pyrochlore phase. SEM studies revealed the heterogeneous grain size distribution for PFN and the homogeneous one for PFT. Dielectric studies pointed to one diffuse T-C phase transition at 378 K for PFN and two diffuse M-T and T-C phase transitions, at 200 and 235 K, for PFT, respectively. X-ray photoelectron spectroscopy studies of PFN reveal that all ions exist in one valence state, however, with two chemical shifts for Pb²⁺. Two valence states for the majority of ions of PFT seem to be connected with a higher volume fraction of the amorphous grain-boundary phase. The electronic energy band gap for both compounds is approximately 2.8 eV. Two magnetic transitions, ie, from the paramagnetic to the antiferromagnetic phase and then to the spin-glass phase, were observed at 156 and 10 K for PFN, and at 145 and 15 K for PFT, respectively.