Effect of fiber surface morphology on the hydrophilicity modification of cold plasma‐treated polypropylene nonwoven fabrics

Cold oxygen plasma was employed to give hydrophilicity modification to polypropylene (PP) nonwoven fabric (NWF). It was found that, after plasma treatment, PP NWF made from fibers with smooth surfaces can only keep its hydrophilicity for a short time and then shows a quick hydrophobic recovery at room temperature. However, this hydrophilic property can last for a long time in the case of the PP NWF made from fibers with rough surfaces. To prove the contribution of the rough surface to the long‐term hydrophilicity, this PP NWF was treated in an organic solvent to smooth the fiber surface. The hydrophilic feature of this PP NWF no longer lasts for a long time after the same plasma treatment. This observation strongly supports our opinion that the fiber surface morphology of PP NWF is a critical factor for long‐term hydrophilicity improvement after plasma treatment, which gives a positive solution to overcoming the aging effect of hydrophilicity modification often found in this technique. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Influence of organically modified nanoclay on the performance of pineapple leaf fiber‐reinforced polypropylene nanocomposites

Polypropylene/Pine apple leaf fiber (PP/PALF)‐reinforced nanocomposites were fabricated using melt blending technique in a twin‐screw extruder (Haake Rheocord 9000). Variation in mechanical properties, crystallization behavior, water absorption, and thermal stability with the addition of nanoclay in PP/PALF composites were investigated. It was observed that the tensile, flexural, and impact properties of PP increase with the increase in fiber loading from 10 to 30 wt %. Composites prepared using 30 wt % PALF and 5 wt % MA‐g‐PP exhibited optimum mechanical performance with an increase in tensile strength to 31%, flexural strength to 45% when compared with virgin PP. Addition of nanoclay results in a further increase in tensile and flexural strength of PP/PALF composites to 20 and 24.3%, which shows intercalated morphology. However, addition of nanoclay does not show any substantial increase in impact strength when compared with PP/PALF composites. Dynamic mechanical analysis tests revealed an increase in storage modulus (E′) and damping factor (tan δ), confirming a strong influence between the fiber/nanoclay and MA‐g‐PP. Differential scanning calorimetry, thermogravimetric analysis thermograms also showed improved thermal properties when compared with the virgin matrix. TEM micrographs also showed few layers of agglomerated clay galleries along with mixed nanomorphology in the nanocomposites. Wide angle X‐ray diffraction studies indicated an increase in d‐spacing from 22.4 Å in Cloisite 20A to 40.1 Å in PP/PALF nanocomposite because of improved intercalated morphology. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Influence of interfacial adhesion on the structural and mechanical behavior of PP‐banana/glass hybrid composites

Hybrid composites of polypropylene (PP), reinforced with short banana and glass fibers were fabricated using Haake torque rheocord followed by compression molding with and without the presence maleic anhydride grafted polypropylene (MAPP) as a coupling agent. Incorporation of both fibers into PP matrix resulted in increase of tensile strength, flexural strength, and impact strength upto 30 wt% with an optimum strength observed at 2 wt% MAPP treated 15 wt% banana and 15 wt% glass fiber. The rate of water absorption for the hybrid composites was decreased due to the presence of glass fiber and coupling agent. The effect of fiber loading in presence of coupling agent on the dynamic mechanical properties has been analyzed to investigate the interfacial properties. An increase in storage modulus (E′) of the treated‐composite indicates higher stiffness. The loss tangent (tan δ) spectra confirms a strong influence of fiber loading and coupling agent concentration on the α and β relaxation process of PP. The nature of fiber matrix adhesion was examined through scanning electron microscopy (SEM) of the tensile fractured specimen. Thermal measurements were carried out through differential scanning calorimetry (DSC) and the thermogravimetric analysis (TGA), indicated an increase in the crystallization temperature and thermal stability of PP with the incorporation of MAPP‐treated banana and glass fiber. POLYM. COMPOS., 31:1247–1257, 2010. © 2009 Society of Plastics Engineers     

Mechanical properties and viscoelastic behavior of basalt fiber‐reinforced polypropylene

In the present article, a series of commercial‐grade polypropylenes (PP) filled with different contents of short basalt fibers were studied. This composite material presented deterioration of both mechanical characteristics, for example, stress and strain at yield with increasing of the fiber content. On the other hand, the impact strength was fourfold higher than that of unfilled PP. A poor adhesion between the PP matrix and the basalt fibers was detected. This is why interfacial interactions were promoted by the adding of poly(propylene‐g‐maleic anhydride) (PP‐g‐MA). It was observed that the tensile properties of the obtained materials and their impact strengths increased significantly with increasing of the amount of PP‐g‐MA in the blend. The adhesion improvement was confirmed by scanning electron microscopy as well. Fourier transform infrared spectroscopy was applied to assess if any chemical interactions in the system PP/PP‐g‐MA/basalt fibers exist. Dynamic mechanical thermal analysis data showed an increase of the storage modulus with increasing fiber content. The conclusion was made that the modification of the PP matrix led to a higher stiffness but its value remained constant, irrespective of the PP‐g‐MA content. With increasing fiber content, damping in the β‐region decreased, but increase of the coupling agent content restored its value back to that of PP. The loss modulus spectra presented a strong influence of fiber content on the α‐relaxation process of PP. The position of the peaks of the above‐mentioned relaxation processes are discussed as well. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 523–531, 1999     

Printing of reactive silicones for surface modification of textile material

For outdoor sports, waterproof breathable materials are widely used to provide protection from environmental factors like rain and wind. The most important techniques to achieve excellent performance use perfluorinated organic substances, which must be replaced in the near future due to health concerns and their environmental persistency. Printing of textile materials with reactive silicone pastes could be an alternative to introduce water repellency without fluorocarbon finishing. In this work, production of barrier textiles through one‐step silicon printing was studied, using a two‐component paste with long pot life and a thermal fixation step. Three different knitted fabrics made from micromodal, polyamide/elastin, and cotton/polyester were used as substrates for the printing. The achieved hydrophobic modification of the fabric was analyzed by determination of water shedding angle, water resistance, water retention values, moisture content, air permeability, tensile properties, and infrared spectroscopy. The results indicate several areas of technical application for the modified fabric, such as barrier textiles with permeability control, localized modification of mechanical properties of fabric and garment. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42594.     

Mechanical properties of wood-fiber/toughened isotactic polypropylene composites

This study investigates the mechanical properties of wood-fiber/toughened PP composite modified by physical blending with an EPDM rubber to improve impact toughness. Wood-fiber thermoplastic composites were prepared with a modified PP matrix resin, employing high shear thermokinetic compounding aided with maleated PP for the fiber dispersion. The addition of EPDM improved the impact toughness, while it reduced stiffness and strength properties. To compensate the non-plane strain fracture toughness, the specimen strength ratio (R_sb) was adopted as a comparative measure of fracture toughness. The strength ratio increased with the addition of EPDM, while it decreased with increasing wood-fiber concentration. The work of fracture increased with EPDM level except at large wood-fiber concentration. The effectiveness of the impact modification was assessed with the balance between tensile modulus and unnotched impact energy as a function of wood-fiber concentration. EPDM rubber modification was moderately effective for wood-fiber PP composites. The examination of fracture surfaces showed twisted fibers, fiber breakage, and fiber pull-out from the matrix resin.     

Microbial modification of polyethylene terephthalate fabric

A great disadvantage of synthetic fibers is their low hydrophilicity. Polyester fibers are particularly hydrophobic. In the first place, this affects the processability of the fibers. The surfaces are not easily wetted, thus impeding the application of finishing compounds and coloring agents. In addition, a hydrophobic material hinders water from penetrating into the pores of fabric. An additional advantage is a decrease in build‐up of electrostatic charge. Besides an improved processability of hydrophilic textiles, a number of advantages from the consumer's point of view are improved washability, as the water can remove hydrophobic stains more easily, and enhanced wearing comfort due to greater water absorbency. For these reasons, hydrophilicity of polyester fabrics was improved using Trametes versicolor. Incubation conditions were determined as; the polyester fabrics were incubated for 10 days at 28°C and 175 rpm. The modification medium was contained 1 g/L glucose and pH of medium was 4. The modification degree was determined according to the contact angle measurements. Water retention values were compatible with contact angle values. FTIR and SEM images showed that the modification occurred on the PET fabric surface. More hydrophilic PET fabric was made by T. versicolor. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Mechanical,thermal, and morphological properties of maleic anhydride‐g‐polypropylene compatibilized and chemically modified banana‐fiber‐reinforced polypropylene composites

Composites were prepared with chemically modified banana fibers in polypropylene (PP). The effects of 40‐mm fiber loading and resin modification on the physical, mechanical, thermal, and morphological properties of the composites were evaluated with scanning electron microscopy (SEM), thermogravimetric analysis (TGA), Infrared (IR) spectroscopy, and so on. Maleic anhydride grafted polypropylene (MA‐g‐PP) compatibilizer was used to improve the fiber‐matrix adhesion. SEM studies carried out on fractured specimens indicated poor dispersion in the unmodified fiber composites and improved adhesion and uniform dispersion in the treated composites. A fiber loading of 15 vol % in the treated composites was optimum, with maximum mechanical properties and thermal stability evident. The composite with 5% MA‐g‐PP concentration at a 15% fiber volume showed an 80% increase in impact strength, a 48% increase in flexural strength, a 125% increase in flexural modulus, a 33% increase in tensile strength, and an 82% increase in tensile modulus, whereas the heat deflection temperature increased by 18°C. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Mechanical,thermal and dynamic‐mechanical behavior of banana fiber reinforced polypropylene nanocomposites

Natural fiber‐reinforced nanocomposites based on polypropylene/nanoclay/banana fibers were fabricated by melt mixing in a twin‐screw extruder followed by compression molding in this current study. Maleic anhydride polypropylene copolymer (MA‐g‐PP) was used as a compatibilizer to increase the compatibility between the PP matrix, clay, and banana fiber to enhance exfoliation of organoclay and dispersion of fibers into the polymer matrix. Variation in mechanical, thermal, and physico‐mechanical properties with the addition of banana fiber into the PP nanocomposites was investigated. It was observed that 3 wt% of nanoclay and 5 wt% of MA‐g‐PP within PP matrix resulted in an increase in tensile and flexural strength by 41.3% and 45.6% as compared with virgin PP. Further, incorporation of 30 wt% banana fiber in PP nanocomposites system increases the tensile and flexural strength to the tune of 27.1% and 15.8%, respectively. The morphology of fiber reinforced PP nanocomposites has been examined by using scanning electron microscopy and transmission electron microscopy. Significant enhancement in the thermal stability of nanocomposites was also observed due to the presence of nanoclay under thermogravimetric analysis. Dynamic mechanical analysis tests revealed an increase in storage modulus (E′) and damping factor (tan δ), conforming the strong interaction between nanoclay/banana fiberand MA‐g‐PP in the fiber‐reinforced nanocomposites systems. POLYM. COMPOS., © 2011 Society of Plastics Engineers.     

Mechanical and thermal properties of toughened polypropylene composites

The mechanical, thermal, and structural properties of a new flexible composite containing polypropylene fiber (PP) in a random poly(propylene‐co‐ethylene) (PPE) matrix with ethylene–propylene elastomer (EP) was investigated with emphasis on the effect of EP elastomer concentration. The intrinsic composition of the composites, toughening of the matrix with EP and the fiber–matrix interface determined the properties of the composites. Through the incorporation of EP elastomer into the polypropylene–poly (propylene‐co‐ethylene) (all‐PP) composite, tensile and storage modulus (E′) decreased, flexural modulus and loss modulus (E″, damping) increased slightly to 0.15 EP and then decreased. There was an increase in impact resistance for the toughened composites, with about 100% increase in comparison with an untoughened all‐PP composite. The composition corresponding to 0.20 weight fraction EP gave optimum impact and mechanical properties. Creep resistance of the composite decreased with increasing EP content, but recovery showed an increase with increasing EP content up to 0.20. Fracture surfaces of composites after impact tests were studied with scanning electron microscopy. Moreover, the use and limitation of theoretical equations to predict the tensile and flexural modulus of the flexible PP composite is discussed. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Modification of jute fabric via laccase/t‐BHP‐mediated graft polymerization with acrylamide

Enzymatic processes provide new perspectives for the modification of lignocellulose materials. Lignin is an excellent substrate for laccase, and the modification of lignin‐rich jute fabric via graft polymerization with acrylamide (AAm) mediated by laccase and tert‐butyl hydroperoxide (t‐BHP) was investigated in this study. The products obtained were characterized by Fourier transform infrared spectroscopy and scanning electron microscopy. The grafting rate was determined in terms of elemental analysis. The hydrophilicity and thermal and dyeing properties of the modified jute fabric were studied. The results supported the conclusion that the polyacrylamide was grafted on the lignin of the jute fiber by laccase in coordination with t‐BHP, representing a grafting rate of 2.87%. The hydrophilicity, thermostability, dye uptake, and dyeing depth of the jute fiber were increased after the enzymatic graft modification with AAm. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40387.     

Grafting modification of electrospun polystyrene fibrous membranes via an entrapped initiator in an acrylic acid aqueous solution

Ultrafine electrospun polymer fibers, with their large specific surface areas, have not found wide applications partly because the fiber surfaces usually carry an insufficient quantity of active groups. The electrospinning and surface‐grafting copolymerization of polystyrene fibrous membranes were carried out via the embedded radical initiator approach. The results from X‐ray photoelectron spectroscopy show that the initiator added to the polystyrene dope was deliberately expelled onto the fiber surfaces. The microstructure and hydrophilicity of the grafted membranes were investigated with Fourier transform infrared spectroscopy, scanning electron microscopy, and water contact angle and water uptake capacity measurements. An increase in the initiator dosages led to decreases in the grafting rate, water uptake, and hydrophilicity of the grafted membranes; the opposite was true for increases in the neutralization of acrylic acid (AA). However, the grafting, water uptake, and hydrophilicity of the grafted membranes presented nonlinear relationships with the concentration of AA. The initiator emigration technique will provide a facile and feasible platform for the surface‐grafting modification of electrospun membranes. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Bamboo fiber reinforced polypropylene composites and their mechanical,thermal, and morphological properties

Short bamboo fiber reinforced polypropylene composites were prepared by incorporation of various loadings of chemically modified bamboo fibers. Maleic anhydride grafted polypropylene (MA‐g‐PP) was used as compatibilizer to improve fiber–matrix adhesion. The effects of bamboo fiber loading and modification of the resin on the physical, mechanical, thermal, and morphological properties of the bamboo reinforced modified PP composites were studied. Scanning electron microscopy studies of the composites were carried out on the interface and fractured surfaces. Thermogravimetric analysis and IR spectroscopy were also carried out. At 50% volume fraction of the extracted bamboo fiber in the composites, considerable increase in mechanical properties like impact, flexural, tensile, and thermal behavior like heat deflection temperature were observed. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Banana/Glass Fiber-Reinforced Polypropylene Hybrid Composites: Fabrication and Performance Evaluation

Hybrid composites of Polypropylene (PP) reinforced with intimately mixed short banana and glass fibers were fabricated using Haake twin screw extruder followed by compression molding with and without the presence maleic anhydride grafted polypropylene (MAPP) as a coupling agent. Incorporation of both the fibers into PP matrix resulted in an increase in tensile, flexural and impact strength with an increasing level of fiber content upto 30 wt% at banana: glass fiber ratio of 15:15 wt% and 2 wt% of MAPP. The rate of water absorption for the hybrid composites decreased due to the presence of glass fiber and coupling agent. The effect of fiber loading in presence of coupling agent on the dynamic mechanical properties has also been analyzed to investigate the interfacial properties. An increase in the storage modulus (E′) of the treated composite indicates higher stiffness. The tan δ spectra confirms a strong influence of fiber contents and coupling agent on the α and β relaxation processes of PP. The nature of fiber matrix adhesion was examined through scanning electron microscopy (SEM) of the tensile fractured specimen. Thermal measurements were carried out employing differential scanning calorimetry (DSC) and the thermogravimetric analysis (TGA) which indicated a decrease in the crystallization temperature and thermal stability of PP with the incorporation of MAPP treated banana and Glass fiber.     

Fabrication and characterization of hydrophilic poly(ε‐caprolactone)/pluronic P123 electrospun fibers

Poly(ε‐caprolactone) (PCL) has been widely investigated for tissue engineering applications because of its good biocompatibility, biodegradability, and mechanical properties; however hydrophobic nature of PCL has been a colossal obstacle toward achieving scaffolds which offer satisfactory cell attachment and proliferation. To produce highly hydrophilic electrospun fibers, PCL was blended with pluronic P123 (P123) and the resulted electrospun scaffolds physiochemical characteristics such as fiber morphology, thermal behavior, crystalline structure, mechanical properties, and wettability were investigated. Moreover molecular dynamic (MD) simulation was assigned to evaluate the blended and neat PCL/water interactions. Presence of P123 at the surface of electrospun blended fibers was detected using ATR‐FTIR analysis. P123 effectiveness in improving the hydrophilicity of the scaffolds was demonstrated by water contact angel which experienced a sharp decrease from 132° corresponding to the neat PCL to almost 0° for all blended samples. Also a steady increase in water uptake ratio was observed for blended fibers as P123 content increased. The 90/10 blend ratio had the maximum tensile strength, elongation at break and crystallinity percentage. Therefore 90/10 blend ratio of PCL/P123 can balance the mechanical properties and bulk hydrophilicity of the resulted electrospun scaffold and would be a promising candidate for tissue engineering application. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43345.     

Effect of silk fiber to the mechanical and thermal properties of its biodegradable composites

In recent years, natural fiber‐reinforced biodegradable thermoplastics are being recognized as an emerging new environmentally friendly material for industrial, commercial, and biomedical applications. Among different types of natural fibers, silk fiber is a common type of animal‐based fiber, has been used for biomedical engineering and surgical operation applications for many years because of its biocompatible and bioresorbable properties. On the basis of our previous study, a novel biodegradable biocomposite for biomedical applications was developed by mixing chopped silk fiber and polylactic acid (PLA) through the injection molding process. This article is aimed at studying the dynamic mechanical and thermal properties of the composite in relation to its biodegradation effect. At the beginning, it was found that the initial storage modulus of a silk fiber/PLA composite increased while its glass transition temperature decreased as compared with a pristine PLA sample. Besides, the coefficient of linear thermal expansions (CLTE) of the composite was reduced by 28%. This phenomenon was attributed to the fiber–matrix interaction that restricted the mobility of polymer chains adhered to the fiber surface, and consequently reduced the T_g and CLTE. It was found that the degraded composite exhibited lower initial storage modulus, loss modulus and tan delta (tan δ) but the T_g was higher than the silk fiber/PLA composite. This result was mainly due to the increase of crystallinity of the composite during its degradation process. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

The effect of fiber concentration on mechanical and thermal properties of fiber‐reinforced polypropylene composites

A novel composite material consisting of polypropylene (PP) fibers in a random poly(propylene‐co‐ethylene) (PPE) matrix was prepared and its properties were evaluated. The thermal and mechanical properties of PP–PPE composites were studied by dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC) with reference to the fiber concentration. Although, by increasing PP fiber concentration in PPE, no significant difference was found in melting and crystallization temperatures of the PPE, the storage, and the tensile and flexural modulus of the composites increased linearly with fiber concentrations up to 50%, 1.5, 1.0, 1.3 GPa, respectively, which was approximately four times higher than that for the pure PPE. There is a shift in glass transition temperature of the composite with increasing fiber concentration in the composite and the damping peak became flatter, which indicates the effectiveness of fiber–matrix interaction. A higher concentration of long fibers (>50% w/w) resulted in fiber packing problems, difficulty in dispersion, and an increase in void content, which led to a reduction in modulus. Cox–Krenchel and Haplin–Tsai equations were used to predict tensile modulus of random fiber‐reinforced composites. A Cole–Cole analysis was performed to understand the phase behavior of the composites. A master curve was constructed based on time–temperature superposition (TTS) by using data over the temperature range from −50 to 90°C, which allowed for the prediction of very long and short time behavior of the composite. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2260–2272, 2005     

Ionic Liquids as New Solvents for Textile Fiber Formation and Modification

Ionic liquids (ILs) with their special characteristics such as low melting point, high thermal stability, electrical conductivity, and good solubility in different chemical liquids, are widely used as new solvents for a large range of inorganic, organic, and polymeric materials. The development of ILs created a great untapped potential for commercial and academic applications to increase operating efficiencies of many chemical processes, including the processing of textiles. A summarizing introduction about ILs, their characterization, the general applications, and the major challenges is presented, followed by previous researches on using ILs for textile fiber formation and modification of their properties.     

Property enhancement in polypropylene ternary blend nanocomposites via a novel poly(ethylene oxide)‐grafted polystyrene‐block‐poly(ethylene/butylene)‐block‐polystyrene toughener–compatibilizer system

Synthesis and characterization of a novel toughener–compatibilizer for polypropylene (PP)–montmorillonite (MMT) nanocomposites were conducted to provide enhanced mechanical and thermal properties. Poly(ethylene oxide) (PEO) blocks were synthetically grafted onto maleic anhydride‐grafted polystyrene‐block‐poly(ethylene/butylene)‐block‐polystyrene (SEBS‐g‐MA). Special attention was paid to emphasize the effect of PEO‐grafted SEBS (SEBS‐g‐PEO) against SEBS‐g‐MA on morphology, static/dynamic mechanical properties and surface hydrophilicity of the resultant blends and nanocomposites. It was found that the silicate layers of neat MMT are well separated by PEO chains chemically bonded to nonpolar SEBS polymer without needing any organophilic modification of the clay as confirmed by X‐ray diffraction and transmission electron microscopy analyses. From scanning electron microscopy analyses, elastomeric domains interacting with MMT layers via PEO sites were found to be distributed in the PP matrix with higher number and smaller sizes than the corresponding blend. As a benefit of PEO grafting, SEBS‐g‐PEO‐containing nanocomposite exhibited not only higher toughness/impact strength but also increased creep recovery, as compared to corresponding SEBS‐g‐MA‐containing nanocomposite and neat PP. The damping parameter of the same nanocomposite was also found to be high in a broad range of temperatures as another advantage of the SEBS‐g‐PEO toughener–compatibilizer. The water contact angles of the blends and nanocomposites were found to be lower than that of neat hydrophobic PP which is desirable for finishing processes such as dyeing and coating. © 2018 Society of Chemical Industry     

Atomic Layer Deposition for Polypropylene Film Engineering—A Review

Polypropylene (PP) polymers are used extensively as dielectric layers, packaging films, and separation membranes, etc. Structure, chemistry, and surface features of PP films dominate their performance and durability. Modification of PP films is carried out using atomic layer deposition (ALD) among other techniques to coat uniform layer of nanometer inorganic material on the surface and inside the pores of PP films to serve the purpose of target applications better. Controlling the reaction temperature, precursor pulsing time, and number of cycles during deposition predominate the thickness, morphology, and composition of the coated layer and hence the performance of PP films. Overall, the ALD technique has been proven to be advantageous in advancing PP film properties such as hydrophilicity, UV resistance, membrane separators, dielectric and mechanical strength, etc., primarily through the controllable formation of nanometer coating on PP films. This review discusses the recent advancements and prospective of ALD in the modification and functionalization of PP films for various applications to provide some insights and motivations to design high‐performance novel PP films by well leveraging the ALD technique.