Effects of amino‐functionalized carbon nanotubes on the properties of amine‐terminated butadiene–acrylonitrile rubber‐toughened epoxy resins

Amino‐functionalized multiwalled carbon nanotubes (MWCNT‐NH₂s) as nanofillers were incorporated into diglycidyl ether of bisphenol A (DGEBA) toughened with amine‐terminated butadiene–acrylonitrile (ATBN). The curing kinetics, glass‐transition temperature (T_g), thermal stability, mechanical properties, and morphology of DGEBA/ATBN/MWCNT‐NH₂ nanocomposites were investigated by differential scanning calorimetry (DSC), thermogravimetric analysis, a universal test machine, and scanning electron microscopy. DSC dynamic kinetic studies showed that the addition of MWCNT‐NH₂s accelerated the curing reaction of the ATBN‐toughened epoxy resin. DSC results revealed that the T_g of the rubber‐toughened epoxy nanocomposites decreased nearly 10°C with 2 wt % MWCNT‐NH₂s. The thermogravimetric results show that the addition of MWCNT‐NH₂s enhanced the thermal stability of the ATBN‐toughened epoxy resin. The tensile strength, flexural strength, and flexural modulus of the DGEBA/ATBN/MWCNT‐NH₂ nanocomposites increased increasing MWCNT‐NH₂ contents, whereas the addition of the MWCNT‐NH₂s slightly decreased the elongation at break of the rubber‐toughened epoxy. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40472.     

Preparation,morphology, and properties of silane‐modified MWCNT/epoxy composites

Both epoxy resin and acid‐modified multiwall carbon nanotube (MWCNT) were treated with 3‐isocyanatopropyltriethoxysilane (IPTES). Scanning electron microscopy (SEM) and transmission electronic microscope (TEM) images of the MWCNT/epoxy composites have been investigated. Tensile strength of cured silane‐modified MWCNT (1.0 wt %)/epoxy composites increased 41% comparing to the neat epoxy. Young's modulus of cured silane‐modified MWCNT (0.8 wt %)/epoxy composites increased 52%. Flexural strength of cured silane‐modified MWCNT (1.0 wt %)/epoxy composites increased 145% comparing to neat epoxy. Flexural modulus of cured silane‐modified MWCNT (0.8 wt %)/epoxy composites increased 31%. Surface and volume electrical resistance of MWCNT/epoxy composites were decreased with IPTES‐MWCNT content by 2 orders and 6 orders of magnitude, respectively. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Preparation and properties of polyurethane‐modified epoxy cured in different simulated gravity environments

Great attention has been paid to the composites with interpenetrating polymer networks (IPNs) because of their special performance. However, the influence of sedimentation and convection from different gravity environments on the formation of IPNs and the properties of IPNs blends has received little attention. To understand their influence, environments with different gravity accelerations of 0g, 1g, and 2g were simulated with a superconducting magnet, and tests, including differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), coefficient of thermal expansion (CTE), scanning electron microscopy, and three‐point bending, of the IPNs blends cured in different gravity environments were conducted and analyzed. Fourier transform infrared spectroscopy, DSC, and DMA proved the formation of IPNs during the reaction between the polyurethane prepolymer (PUP) and epoxy resin (E51). The curves of DSC also certified the differences in the curing degree between the different parts along the direction of gravity of a sample. With the increase of mass fraction of PUP, the change trends of the storage modulus presented a linear decrease when samples cured in microgravity environment, but presented a parabolic trend when samples were cured in terrestrial environment. The damping properties of samples cured in simulated microgravity environments are better than those cured in terrestrial environment. With the increase in the simulated acceleration of gravity, the diameter of dispersed phase in a sea‐island structure increased, but their number decreased and the bending stress and CTE of the IPN blends all decreased. These results show the formation of IPNs was affected by different gravity values, and the thermal and mechanical properties of the IPN composites were influenced by the changed IPN components. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42063.     

Conducting epoxy networks modified with non‐covalently functionalized multi‐walled carbon nanotube with imidazolium‐based ionic liquid

Multi‐walled carbon nanotube (MWCNT) was non‐covalently functionalized with room‐temperature ionic liquid (IL), 1‐butyl‐3‐methyl‐imidazolium tetrafluoroborate and blended with epoxy pre‐polymer (ER) with the assistance of ultrasonication in the presence of acetone as a diluting medium. The ability of IL in improving the dispersion of MWCNT in epoxy pre‐polymer was evidenced by transmission optical microscopy. The corresponding epoxy/MWCNT networks cured with anhydride displayed an increase of the electrical conductivity of around three orders of magnitude with the addition of IL in a proportion of MWCNT/IL = 1:5 mass ratio. The effect of IL on dynamic mechanical properties and thermal conductivity was also evaluated. The improved thermal and electrical properties was attributed to the better dispersion of MWCNT within the epoxy matrix by IL, evidenced by transmission electron microscopy of the ER/MWCNT networks cured with anhydride. Raman spectroscopy was also used to confirm the interaction between MWCNT and IL. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43976.     

A comparative study on the properties of the different amino‐functionalized multiwall carbon nanotubes reinforced epoxy resin composites

Multiwall carbon nanotubes (MWCNTs) were amino‐functionalized by 1,2‐ethylenediamine (EDA)' triethylenetetramine (TETA), and dodecylamine (DDA), and investigated by fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, and thermogravimetric analysis (TGA). The dispersion of the DDA functionalized MWCNT in DMF is better than that of the MWCNT functionalized by the EDA and the TETA. Carbon nanotubes reinforced epoxy resin composites were prepared, and the effect of the amino‐functionalization on the properties of the composites was investigated by differential scanning calorimetry (DSC), dynamical mechanical analysis (DMA), and TGA. The composites reinforced by the MWCNTs demonstrate improvement in various mechanical properties. The increase of T_g of the composites with the addition of amino‐functionalized MWCNT compared to the T_g of the composites with the addition of unfunctionalized MWCNT was due to the chemical combination and the physical entanglements between amino group from modified MWNTs and epoxy group from the epoxy resin. The interfacial bonding between the epoxy and the amino group of the EDA and the TETA‐modified MWCNT is more important than the well dispersion of DDA‐modified MWCNT in the composites for the improvement of the mechanical properties. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Functionalization of carbon nanotubes with (3‐glycidyloxypropyl)‐trimethoxysilane: Effect of wrapping on epoxy matrix nanocomposites

In this work, multiwalled carbon nanotubes (MWCNT), after previous oxidation, are functionalized with excess (3‐glycidyloxypropyl)trimethoxysilane (GLYMO) and used as reinforcement in epoxy matrix nanocomposites. Infrared, Raman, and energy‐dispersive X‐ray spectroscopies confirm the silanization of the MWCNT, while transmission electron microscopy images show that oxidized nanotubes presented less entanglement than pristine and silanized MWCNT. Thickening of the nanotubes is also observed after silanization, suggesting that the MWCNT are wrapped by siloxane chains. Field‐emission scanning electron microscopy reveals that oxidized nanotubes are better dispersed in the matrix, providing nanocomposites with better mechanical properties than those reinforced with pristine and silanized MWCNT. On the other hand, the glass transition temperature of the nanocomposite with 0.05 wt % MWCNT‐GLYMO increased by 14 °C compared to the neat epoxy resin, suggesting a strong matrix–nanotube adhesion. The functionalization of nanotubes using an excess amount of silane can thus favor the formation of an organosiloxane coating on the MWCNT, preventing its dispersion and contributing to poor mechanical properties of epoxy nanocomposites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44245.     

Synthesizing multi‐walled carbon nanotube‐polymethyl methacrylate conductive composites and poly(lactic acid) based composites

Multi‐walled carbon nanotube was modified with polymethyl methacrylate (MWCNT‐PMMA) by in situ solution radical polymerization in the presence of 2,2′‐Azobis (isobutyronitrile) as an initiator. The products with different addition of methyl methacrylate (MMA) were pressed into slices to prepare specimens for electrical conductivity testing. It was found that the MWCNT‐PMMA nanocomposites demonstrate excellent electrical conductivity. To investigate the microsphere morphology and the colloidal surfactant of MWCNTs in MWCNT‐PMMA composites, samples were submitted to scanning electron microscopy and transmission electron microscopy. The thermogravimetric analysis of the prepared composites confirmed that MWCNTs as a thermal stabilizer for PMMA, which could have a wide range of potential applications, such as in catalysts, sensors, environmental remediation, and energy storage. Two series of poly(lactic acid) (PLA) based biocomposites with different MMA additions and MWCNT‐PMMA composites contents were prepared with twin‐screw extruding and injection molding. The results show the mechanical properties changed a little with the MMA and MWCNT‐PMMA composites contents increasing, which suggested the well compatibility between MWCNT‐PMMA composites and PLA. POLYM. COMPOS., 37:503–511, 2016. © 2014 Society of Plastics Engineers     

Glass fiber‐reinforced composites of diglycidyl ether of 2,7‐dihydroxy naphthalene

The curing reactions of epoxy resin diglycidyl ether of 2,7‐dihydroxy naphthalene (DGEDHN) with different aliphatic and aromatic amines have been studied by differential scanning calorimetry (DSC). The thermal stability of the cured products was also studied by thermogravimetric analysis (TGA). Using these data, different glass fiber‐reinforced composites were fabricated, and their mechanical, electrical properties and resistance to chemicals were studied. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1345–1349, 2000     

Development of multiwalled‐carbon‐nanotube‐welded carbon fibers and evaluation of the interfacial strength in epoxy composites

Multiwalled carbon nanotube (MWCNT)‐welded carbon fibers (CFs) were prepared by a three‐step process, which included polyacrylonitrile (PAN) coating, MWCNT absorption, and heat treatment. The structure of these materials was characterized by scanning electron microscopy, Fourier‐transform infrared spectroscopy, and Raman spectroscopy. The MWCNTs were uniformly assembled on the surface of the PAN‐coated CFs and welded by a PAN‐based carbon layer after heat treatment. The contact angle of the MWCNT‐welded CFs in the epoxy resins was 41.70°; this was 22.35% smaller than that of the unsized CFs. The interfacial shear strength (IFSS) of the MWCNT‐welded CF–epoxy composite was 83.15 MPa; this was 28.89% higher than that of the unsized CF–epoxy composite. The increase in the IFSS was attributed to the enhancement of adhesions between the CFs and polymer matrix through the welding of the MWCNTs on the CFs. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45027.     

Synthesis and characterization of LiFePO4–carbon nanofiber–carbon nanotube composites prepared by electrospinning and thermal treatment as a cathode material for lithium‐ion batteries

Binder‐free LiFePO₄–carbon nanofiber (CNF)–multiwalled carbon nanotube (MWCNT) composites were prepared by electrospinning and thermal treatment to form a freestanding conductive web that could be used directly as a battery cathode without addition of a conductive material and polymer binder. The thermal decomposition behavior of the electrospun LiFePO₄ precursor–polyacrylonitrile (PAN) and LiFePO₄ precursor–PAN–MWCNT composites before and after stabilization were studied with thermogravimetric analysis (TGA)/differential scanning calorimetry and TGA/differential thermal analysis, respectively. The structure, morphology, and carbon content of the LiFePO₄–CNF and LiFePO₄–CNF–MWCNT composites were determined by X‐ray diffraction, high‐resolution transmission electron microscopy, Raman spectroscopy, scanning electron microscopy, and elemental analysis. The electrochemical properties of the LiFePO₄–CNF and LiFePO₄–CNF–MWCNT composite cathodes were measured by charge–discharge tests and electrochemical impedance spectroscopy. The synthesized composites with MWCNTs exhibited better rate performances and more stable cycle performances than the LiFePO₄–CNF composites; this was due to the increase in electron transfer and lithium‐ion diffusion within the composites loaded with MWCNTs. The composites containing 0.15 wt % MWCNTs delivered a proper initial discharge capacity of 156.7 mA h g^?1 at 0.5 C rate and a stable cycle ability on the basis of the weight of the active material, LiFePO₄. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43001.     

Preparation and properties of multiwalled carbon nanotube/epoxy‐amine composites

Different amounts of multiwalled carbon tubes (MWCNTs) were incorporated into an epoxy resin based on diglycidyl ether of bisphenol A and both epoxy precursor and composite were cured with 4,4′‐diamino diphenyl sulfone. Transmission and scanning electron microscopy demonstrated that the carbon nanotubes are dispersed well in the epoxy matrix. Differential scanning calorimetry measurements confirmed the decrease in overall cure by the addition of MWCNTs. A decrease in volume shrinkage of the epoxy matrix caused by the addition of MWCNTs was observed by pressure–volume–temperature measurements. Thermomechanical and dynamic mechanical analysis were performed for the MWCNT/epoxy composites, showing that the T_g was slightly affected, whereas the dimensional stability and stiffness are improved by the addition of MWCNTs. Electrical conductivity measurements of the composite samples showed that an insulator to conductor transition takes place between 0.019 and 0.037 wt % MWCNTs. The addition of MWCNTs induces an increase in both impact strength (18%) and fracture toughness (38%) of the epoxy matrix with very low filler content. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Influence of the epoxy functionalization of multiwall carbon nanotubes on the nonisothermal cure kinetics and thermal properties of epoxy/multiwall carbon nanotube nanocomposites

Multiwall carbon nanotubes were functionalized with epoxy groups by chemical modification in four stages. At each stage, the compound was characterized by Fourier transform infrared spectroscopy and scanning electron microscopy (SEM). Epoxy composite samples were prepared by mixing diglycidyl ether of bisphenol A‐based epoxy resin and synthetic epoxy‐functionalized multiwall carbon nanotube (E‐MWCNT) with different percentages (1, 3, 6, 9, 12, and 15%) in acetone. Ultrasonic dispersion was used to produce homogenous blends. The optimum ratio of the reacting components (9%) was investigated by total enthalpy of the curing reaction from differential scanning calorimetry (DSC) thermograms. The kinetics of the curing reaction for epoxy composites with 4,4′‐diaminodiphenylsolfon as a curing agent was studied by means of a DSC nonisothermal technique. The kinetic parameters such as activation energy, pre‐exponential factor, and rate constant were obtained from DSC data. The structure ofthe nanocomposites and dispersion of the E‐MWCNTs in the nanocomposites were observed using SEM, and the thermal properties were studied by thermogravimetric analysis. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

功能化碳纳米管/环氧树脂多孔复合材料制备及电磁屏蔽性能

以马来酸酐（MA）为功能性单体,通过自由基反应制备了马来酸酐功能化的多壁碳纳米管（MA-MWCNT）;以MA-MWCNT、环氧树脂、蓖麻油酸改性的四乙烯五胺固化剂、釉粉、水为原料,通过悬浮乳液聚合法制备了功能化碳纳米管/环氧树脂多孔复合材料。采用拉曼光谱、X射线衍射、红外光谱、X射线光电子能谱对功能化的碳纳米管进行了表征和测试。采用扫描电镜（SEM）、表面电阻测量仪、矢量网络分析仪对复合材料的表面形貌、电导率和电磁屏蔽性能进行了测试。结果表明：马来酸酐功能化单体的引入能够很好地改善碳纳米管的分散性能及材料的电磁屏蔽性能;随着碳纳米管含量的增多,复合材料的电导率增大,电磁屏蔽效能峰值增大,材料的电磁屏蔽性能增强;加入功能化的碳纳米管比加入未功能化碳纳米管的电磁屏蔽性能高,多孔复合材料比无孔复合材料的电磁屏蔽性能高。当加入功能化的碳纳米管的量为3%时,制备得到的多孔材料电磁屏蔽性能最佳,其电磁屏蔽性能峰值达到31.1dB。     

Nanostructured thermosetting epoxy systems modified with poly(isoprene‐b‐methyl metacrylate) diblock copolymer and polyisoprene‐grafted carbon nanotubes

Nanostructured thermosetting composites based on an epoxy matrix modified with poly(isoprene‐b‐methyl methacrylate) (PI‐b‐PMMA) block copolymer were prepared through PI block segregation. Morphological structures were examined by means of atomic microscopy force microscopy. As epoxy/pristine multi‐walled carbon nanotubes (MWCNT) systems were found to present big agglomerations, with a very poor dispersion of the nanofiller, epoxy/PI‐b‐PMMA/MWCNT systems were prepared by using polyisoprene‐grafted carbon nanotubes (PI‐g‐CNT) to enhance compatibility with the matrix and improve dispersion. It was found that the functionalization of MWCNT with grafted polyisoprene was not enough to totally disperse them into the epoxy matrix but an improvement of the dispersion of carbon nanotubes was achieved by nanostructuring epoxy matrix with PI‐b‐PMMA when compared with epoxy/MWCNT composites without nanostructuring. Nevertheless, some agglomerates were still present and the complete dispersion or confinement of nanotubes into desired domains was not achieved. Thermomechanical properties slightly increase with PI‐g‐CNT content for nanostructured samples, whereas for nonnanostructured epoxy/PI‐g‐CNT composites they appeared almost constant and even decreased for the highest nanofiller amount due to the presence of agglomerates. Compression properties slightly decreased with block copolymer content, while remained almost constant with nanofiller amount. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

The conductivity behavior of multi‐component epoxy,metal particle,carbon black,carbon fibril composites

Following the previous studies of epoxy/silver conductive composites, a detailed investigation of the influence of ethylene glycol on the resulting resistivity of various composites was carried out. Ethylene glycol was found to have a catalytic effect on the curing process of the epoxy resin, verified by differential scanning calorimetry studies. The accelerated curing process diminishes settling of the metal particles and therefore results in better and more uniform conductivities. High temperature curing of the composites was found to have a similar effect on the conductivity. The conductivity behavior of some other composites, such as epoxy/nickel, epoxy/nickel/carbon fibrils, and epoxy/carbon black/carbon fibrils, were also studied. The structure–property relations were better understood through scanning electron microscopy observations. Silver and nickel particles were found to perform differently in the cured epoxy, showing different percolation concentrations and conductivity levels. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1706–1713, 2002     

Modeling of chemical kinetics of elastomer/hydroxyl‐ and carboxyl‐functionalized multiwalled carbon nanotubes nanocomposites' cross‐linking

Several kinds of (hydrogenated) nitrile elastomer ((H)NBR) compounds were prepared by melt compounding of rubbers with carbon nanotubes. Transmission electron microscopy (TEM) showed that the exfoliation degree of nanotubes was high. Multiwalled carbon nanotubes (MWCNT) were either neat or modified by hydroxyl or carboxyl groups. Morphology was also characterized by scanning electron microscopy (SEM). The cure kinetics of (H)NBR and modified multiwalled carbon nanotubes ((m‐)MWCNT/(H)NBR) nanocomposites was studied. It was found that the apparent curing and over‐cure activation energies (E_A and E_A,1) increased with the increasing amount of (m‐)MWCNT. There was a less obvious change in the apparent orders of curing reactions. The results of n‐th order and autocatalytic kinetic model showed that any studied content of (m‐)MWCNT could increase effective thermal conductivity, but decreased the vulcanization rate of (m‐)MWCNT/(H)NBR nanocomposites. Finally, the effect of (m‐)MWCNT content and functionalization on tensile mechanical properties was presented. POLYM. ENG. SCI., 2011. © 2010 Society of Plastics Engineers     

Improving thermal conductivity and shear strength of carbon nanotubes/epoxy composites via thiol‐ene click reaction

This study investigates the effect of the thiol‐ene click reaction on thermal conductivity and shear strength of the epoxy composites reinforced by various silane‐functionalized hybrids of sulfhydryl‐grafted multi‐walled carbon nanotubes (SH‐MWCNTs) and vinyl‐grafted MWCNTs (CC‐MWCNTs). The results of Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, thermal gravimetric analysis (TGA), and transmission electron microscopy (TEM) show that the sulfhydryl groups and vinyl groups are successfully grafted onto the surface of MWCNTs, after treatment of MWCNT with triethoxyvinylsilane and 3‐mercaptopropyltrimethoxysilane, respectively. Scanning electron microscopy (SEM), HotDisk thermal constant analyzer (HotDisk), optical microscope, and differential scanning calorimetry (DSC) are used to characterize the resultant composites. It is demonstrated that the hybrid of 75 wt % SH‐MWCNTs and 25 wt % CC‐MWCNTs has better dispersion and stability in epoxy matrix, and shows a stronger synergistic effect in improving the thermal conductivity of epoxy composite via the thiol‐ene click reaction with 2,2′‐azobis(2‐methylpropionitrile) as thermal initiator. Furthermore, the tensile shear strength results of MWCNT/epoxy composites and the optical microscopy photographs of shear failure section indicate that the composite with the hybrid MWCNTs has higher shear strength than that with raw MWCNTs. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44579.     

Preparation of epoxy composites with CTAB‐modified BN and MWCNTs

In this study, multi‐walled carbon nanotubes (MWCNTs) and boron nitride (BN) were functionalized with cetyltrimethylammonium bromide (CTAB) at both pH 5.5 and pH 11. These MWCNT‐CTAB and BN‐CTAB particles used to prepare the composites were dispersed in a bisphenol A (DGEBA)‐type epoxy resin (ER) system at room temperature. The TGA analysis showed that the BN composite can significantly improve the thermal stability of neat ER at temperatures above 400 °C. The curing degrees of the nanocomposites were calculated to be approximately the same values as neat ER using the Beer–Lambert law from FTIR spectra. The best electrical conductivity of the composites obtained was 3.10 × 10⁻³ S/cm for ER/MWCNT‐CTAB (pH 5.5). The surface hardness, Young's modulus, and tensile strength of the composites were examined. The surface hardness values of the ER/MWCNT‐CTAB composites were higher than those of the other composites. The composite morphology was characterized using X‐ray diffraction (XRD) and scanning electron microscopy (SEM). POLYM. COMPOS., 37:3423–3432, 2016. © 2015 Society of Plastics Engineers     

Thermophysical properties of anhydride‐cured epoxy/nano‐clay composites

Polymer nano‐composites made with a matrix of anhydride‐cured diglycidyl ether of bisphenol A (DGEBA) and reinforced with organo‐montmorillonite clay were investigated. A sonication technique was used to process the epoxy/clay nano‐composites. The thermal properties of the nano‐composites were measured with dynamic mechanical analysis (DMA). The glass transition temperature T_g of the anhydride‐cured epoxy was higher than the room temperature (RT). For samples with 6.25 wt% (4.0 vol%) of clay, the storage modulus at 30°C and at (T_g + 15)°C was observed to increase 43% and 230%, respectively, relative to the value of unfilled epoxy. The clay reinforcing effect was evaluated using the Tandon‐Weng model for randomly oriented particulate filled composites. Transmission electron microscopy (TEM) examination of the nano‐composites prepared by sonication of clays in acetone showed well‐dispersed platelets in the nano‐composites. The clay nano‐platelets were observed to be well‐intercalated/expanded in the anhydride‐cured epoxy resin system. POLYM. COMPOS., 26:42–51, 2005. © 2004 Society of Plastics Engineers.     

Preparation and properties of MWCNTs/poly(acrylonitrile‐ styrene‐butadiene)/epoxy hybrid composites

Poly(acrylonitrile‐styrene‐butadiene) (ABS) was used to modify diglycidyl ether of bisphenol‐A (DGEBA) type epoxy resin, and the modified epoxy resin was used as the matrix for making multiwaled carbon tubes (MWCNTs) reinforced composites and were cured with diamino diphenyl sulfone (DDS) for better mechanical and thermal properties. The samples were characterized by using infrared spectroscopy, pressure volume temperature analyzer (PVT), thermogravimetric analyzer (TGA), dynamic mechanical analyzer (DMA), thermo mechanical analyzer (TMA), universal testing machine (UTM), and scanning electron microscopy (SEM). Infrared spectroscopy was employed to follow the curing progress in epoxy blend and hybrid composites by determining the decrease of the band intensity due to the epoxide groups. Thermal and dimensional stability was not much affected by the addition of MWCNTs. The hybrid composite induces a significant increase in both impact strength (45%) and fracture toughness (56%) of the epoxy matrix. Field emission scanning electron micrographs (FESEM) of fractured surfaces were examined to understand the toughening mechanism. FESEM micrographs reveal a synergetic effect of both ABS and MWCNTs on the toughness of brittle epoxy matrix. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013