Enhancement of physical and mechanical properties of polyamide 66 fibers using polysiloxane-functionalized multi-walled carbon nanotubes

A polyamide 66/3-aminopropyl-terminated poly(dimethylsiloxane) (PA66/APDMS)-carboxylate multiwalled carbon nanotubes (CMWNTs) nanocomposite (PA66/APDMS-CMWNTs) was synthesized using a one-pot method, and the product was melt-spun into fibers. The glass transition temperature (T_g) of the PA66/APDMS-CMWNTs nanocomposite fiber is 68.0°C, which is 22% higher than that of the pure PA66 fiber. This result indicates that there is a strong interfacial interaction between APDMS-CMWNTs and the PA66. Furthermore, the crystallinity of PA66/APDMS-CMWNTs nanocomposite fiber reaches a maximum due to the addition of APDMS-CMWNTs. Additionally, the tensile strength and Young's modulus of PA66/APDMS-CMWNTs nanocomposite fiber are 167% and 631% higher, respectively, than that of the pure PA66 fiber. The strengthening mechanism was discussed using force balance-based expression, which demonstrates that the stress on the PA66 is more efficiently transferred to the APDMS-CMWNTs. These results argue that using APDMS-CMWNTs as a filler can enhance the physical-mechanical properties of PA66 with an elevated degree never being reported.     

Effect of the nanotube aspect ratio and surface functionalization on the morphology and properties of multiwalled carbon nanotube polyamide‐based fibers

In this study, the effect of the carbon nanotube (CNT) aspect ratio and surface functionalization on the mechanical behavior and morphological changes of polyamide (PA)‐based fibers was investigated. Composites were prepared by the melt blending of CNTs with PA, and at a later time, the fibers were prepared by melt spinning and cold drawing. A reinforcement effect was noticed for all of the CNTs samples, and the increase in the mechanical properties and dimensional stability was more pronounced for highly oriented filaments. When the elongational flow was increased, the orientation of CNTs along the fiber direction was observed, but the nanotube alignment was much more difficult for CNTs with ultrathin outer diameters because of nanotube waviness and folding. Moreover, the presence of functional groups on the CNT surface hindered their orientation along the fiber direction because some interaction between the functional groups could occur. The morphological variations of the oriented, anisotropic fibers, as studied with transmission electron microscopy, scanning electron microscopy, small‐angle X‐ray scattering, and differential scanning calorimetry analysis, were correlated with changes in the mechanical behavior. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effect of surface modification of graphite oxide on the morphological,thermal, and mechanical properties of polyurea/graphite oxide composites

Three surface modifiers, namely, aminopolyether (D2000), phenyl isocyanate, and poly(ethylene glycol) (PEG800), which have different affinities to the hard and soft segments in polyurea, were used to synthesize functionalized graphite oxides (GO). The PEG800‐modified (PEG800‐GO) and phenyl isocyanate‐modified (i‐GO) GOs were highly exfoliated and dispersed in DMF, whereas the D2000‐modified GO (D2000‐GO) produced some precipitates. Polyurea/GO composites were prepared using a solution‐blending method, in which functionalized GO platelet suspensions in dimethyl formamide were used. Results show that PEG800‐GO and i‐GO are uniformly dispersed throughout the polymer matrix on a nanoscale, whereas D2000‐GO forms visible aggregates. The well‐dispersed GO platelets improved the thermal stability and mechanical properties of polyurea. PEG800‐GO, which has a strong affinity for the soft segments, shows a more significant reinforcing effect. At 2.0 wt % GO loading, the tensile strength of polyurea was enhanced by ～75%. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39775.     

Mechanical and thermal transmission properties of carbon nanofiber‐dispersed carbon/phenolic multiscale composites

The present article reports the development and characterization of carbon nanofiber (CNF)‐incorporated carbon/phenolic multiscale composites. Vapor‐grown CNFs were dispersed homogeneously in to phenolic resin using an effective dispersion route, and carbon fabrics were subsequently impregnated with the CNF‐dispersed resin to develop carbon fiber/CNF/phenolic resin multiscale composites. Mechanical and thermal transmission properties of multiscale composites were characterized. Elastic modulus and thermal conductivity of neat carbon/phenolic and multiscale composites were predicted and compared with the experimental results. It was observed that incorporation of only 1.5 wt % CNF resulted in 10% improvement in Young's modulus, 12% increase in tensile strength, and 36% increase in thermal conductivity of carbon/phenolic composites. Fracture surface of composite samples revealed the formation of stronger fiber/matrix interface in case of multiscale composites than neat carbon/phenolic composites. Enhancement of above properties through CNF addition has been explained, and the difference between the predicted values and experimental results has been discussed. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Mechanical properties of carbon fiber reinforced bisphenol A dicyanate ester composites modified with multiwalled carbon nanotubes

A novel electrophoretic deposition (EPD) method was employed for grafting multiwalled carbon nanotubes (MWCNTs) on carbon fibers, which, after impregnation with bisphenol A dicyanate ester (BADCy), synergistically reinforced BADCy matrix composites (CNT‐C/BADCy). The effect of MWCNT presence on the mechanical properties of the composites was investigated. Composite tensile strength increased by 45.2% for an EPD duration of 2 min, while flexural strength exhibited a decreasing trend with EPD duration. Optical microscopy revealed that the existence of MWCNTs enhanced the fiber‐matrix interface while a large number of CNTs were observed to have pulled‐out from the matrix, a finding which explained the observed tensile strength increase in terms of energy dissipation by the specific toughening mechanism. The flexural strength decrease of the composites with CNTs as compared to specimens without nanotubes was found linked to the increased stress concentration in the BADCy matrix due to tube presence which weakens the adhesion between carbon fabrics. In a word, carbon nanotubes will enhance the micro interface and weaken the macro interface of the composites. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45100.     

Effects of fiber surface grafting by functionalized carbon nanotubes on the interfacial durability during cryogenic testing and conditioning of CFRP composites

Carbon fiber reinforced epoxy (CE) composite is ideal for a cryogenic fuel storage tank in space applications due to its unmatched specific strength and modulus. In this article, inter-laminar shear strength (ILSS) of carbon fiber/epoxy (CE) composite is shown to be considerably improved by engineering the interface with carboxyl functionalized multi-walled carbon nanotube (FCNT) using electrophoretic deposition technique. FCNT deposited fibers from different bath concentrations (0.3, 0.5, and 1.0 g/L) were used to fabricate the laminates, which were then tested at room (30°C) and in-situ liquid nitrogen (LN) (−196°C) temperature as well as conditioning for different time durations (0.25, 0.5, 1, 6, and 12 h) followed by immediate RT testing to study the applicability of these engineered materials at the cryogenic environment. A maximum increment in ILSS was noticed at bath concentration of 0.5 g/L, which was ~21% and ~ 17% higher than neat composite at 30°C and − 196°C, respectively. Short-term LN conditioning was found to be detrimental due to developed cryogenic shock, which was further found to be compensated by cryogenic interfacial clamping upon long-term exposure.     

Effects of substitution for carbon black with graphene oxide or graphene on the morphology and performance of natural rubber/carbon black composites

In this study, nanosheets including graphene oxide (GO) and reduced graphene oxide (rGO), were incorporated into natural rubber (NR), to study the effects of substituting GO or rGO for carbon black (CB) on the structure and performance of NR/CB composites. The morphological observations revealed the dispersion of CB was improved by partially substituting nanosheets for CB. The improvements in static and dynamic mechanical properties were achieved at small substitution content of GO or rGO nanosheets. With substitution of rGO nanosheets, significant improvement in flex cracking resistance was achieved. NR/CB/rGO (NRG) composites has a much lower heat build‐up value compared with NR/CB/GO (NG) composites at a high load of nanosheets. However, both GO and rGO tended to aggregate at a high concentration, which led to the poor efficiency on enhancing the dynamic properties, or even deteriorate the performance of rubber composites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41832.     

Enhanced mechanical and electrical properties of nylon‐6 composite by using carbon fiber/graphene multiscale structure as additive

In order to improve the mechanical properties and electrical conductivity of nylon‐6 (PA6) composites, a highly effective multiscale structure filler comprising poly(diallyldimethylammonium chloride) (PDDA)‐modified graphene and negatively surface‐charged carbon fiber was synthesized in this study. For this, the graphene used a top‐down method for synthesis by exfoliating graphite oxide (GO) through focused solar radiation on it and then modified its surface by using a polyelectrolyte. The carbon fiber (CF) surface was functionalized by an acid oxidation method. The multiscale structure was manufactured via the electrostatic interaction between the positively charged solar graphene (SG) and oppositely charged CF by homogeneous mixing. Scanning electron microscopy (SEM) images of the fracture surface of the PA6 composites exhibited that the carbon fiber/graphene multiscale structure possessed better dispersion and compatibility than those of individual CF and SG did. Thus, the impact strength, bending properties, and electrical conductivity of the PA6 composites were enhanced. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41968.     

Effects of electrophoretic deposition process parameters on the mechanical properties of graphene carboxyl-grafted carbon fiber reinforced polymer composite

Carbon fiber (CF) modification by grafting of various graphene-based nanofillers (GBN) by electrophoretic deposition (EPD) technique was proven to be a successful technique to enhance the out-of-plane performance of carbon fiber reinforced polymer (CFRP) composites. Graphene carboxyl (G-COOH) grafting on carbon fiber by electrophoretic deposition (EPD) is a promising technique to improve the mechanical properties of CFRP composites. To our knowledge, there is a dearth of literature available on the effect of EPD process parameters on the mechanical behavior of modified CFRP composites. The aim of this study is to evaluate the effect of nanofiller concentration in the suspension, applied current, and the time of deposition during EPD on the mechanical behavior of nanophase CFRP composites, thus making it a novel work. With increasing concentration, interlaminar shear strength (ILSS) improved consistently and has shown a maximum enhancement of 24.7% than that of neat CFRP composite at 1.5 g/L nanofiller concentration, whereas flexural strength remained almost unaffected with varying concentration. On the contrary, variation of deposition current has affected the flexural strength but not ILSS. The maximum flexural strength was obtained at a deposition current of 5.0A with an improvement of 16.3% in comparison with neat CFRP samples. However, both flexural strength and ILSS of hybrid CFRP composites have shown improvement with increasing deposition time. At 60 min of deposition, ILSS and flexural strength have shown maximum improvements of 35.0 and 26.6%, respectively, when compared to control specimen. After evaluating the effect of process parameters future scope of the work involves the optimization of parameters for EPD of G-COOH. Fractographic analysis of the fractured samples was performed using scanning electron microscope (SEM) to apprehend prominent failure mechanisms. © 2020 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48925.     

Synergistic effects of carbon nanotubes and carbon black on the fracture and fatigue resistance of natural rubber composites

The quasi‐static fracture and dynamic fatigue behaviors of natural rubber composites reinforced with hybrid carbon nanotube bundles (CNTBs) and carbon black (CB) at similar hardness values were investigated on the basis of fracture mechanical methods. Mechanical measurement and J‐integral tests were carried out to characterize the quasi‐static fracture resistance. Dynamic fatigue tests were performed under cyclic constant strain conditions with single‐edged notched test pieces. The results indicate that synergistic effects between CNTBs and CB on the mechanical properties, fracture, and fatigue resistance were obtained. The composite reinforced with 3‐phr CNTBs displayed the strongest fatigue resistance. The synergistic mechanisms and dominating factors of quasi‐static and dynamic failure, such as the dispersion state of nanotubes, hybrid filler network structure, strain‐induced crystallization, tearing energy input, and viscoelastic hysteresis loss, were examined. The weakest fatigue resistance of the composite filled with 5‐phr CNTBs was ascribed to its strikingly high hysteresis, which resulted in marked heat generation under dynamic fatigue conditions. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42075.     

Influence of preparation methods on the electrical and nanomechanical properties of poly(methyl methacrylate)/multiwalled carbon nanotubes composites

Poly(methyl methacrylate)/multiwalled carbon nanotubes (PMMA/MWCNT) composites were prepared by two different methods: melt mixing and solution casting. For solution casting, two different solvents, toluene and chloroform, were used to prepare PMMA solutions with different concentrations of MWCNT. The dispersion of the CNT in the composite samples was verified by scanning electron microscopy. For the nanocomposites prepared by both methods, the electrical conductivity increased with increasing filler content, showing typical percolation behavior. In addition, an increase of 11 orders of magnitude in the electrical conductivity relative to the matrix conductivity was determined by broadband dielectric spectroscopy and four probe conductivity measurements. A maximum value of σ_DC ～ 1.6 S/cm was found for the highest filler loaded sample (3.67 vol %), which was prepared by solution casting from toluene. Nanoindentation analysis was used to characterize the surface mechanical properties of the composite samples prepared by the different methods. Indentation tests were performed at various penetration depths, and it was revealed that the melt mixing process resulted in stiffer neat PMMA samples compared to the solution casted PMMA samples. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41721.     

Thermoplastic polyvinyl alcohol/multiwalled carbon nanotube composites: Preparation,mechanical properties,thermal properties,and electromagnetic shielding effectiveness

This study uses the solution mixing method to combine plasticized polyvinyl alcohol (PVA) as a matrix, and multiwalled carbon nanotubes (MWCNTs) as reinforcement to form PVA/MWCNTs films. The films are then laminated and hot pressed to create PVA/MWCNTs composites. The control group of PVA/MWCNTs composites is made by incorporating the melt compounding method. Diverse properties of PVA/MWCNTs composites are then evaluated. For the experimental group, the incorporation of MWCNTs improves the glass transition temperature (T_g), crystallization temperature, T_c), and thermal stability of the composites. In addition, the test results indicate that composites containing 1.5 wt % of MWCNTs have the maximum tensile strength of 51.1 MPa, whereas composites containing 2 wt % MWCNTs have the optimal electrical conductivity of 2.4 S/cm, and electromagnetic shielding effectiveness (EMI SE) of ?31.41 dB. This study proves that the solution mixing method outperforms the melt compounding method in terms of mechanical properties, dispersion, melting and crystallization behaviors, thermal stability, and EMI SE. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43474.     

Synergetic effects on the mechanical and fracture properties of epoxy composites with multiscale reinforcements: Carbon nanotubes and short carbon fibers

The ball‐milling/liquid‐phase oxidation (BMLPO) method was used to fabricate surface‐modified short carbon fibers (SCFs). Multiscale epoxy composites reinforced with a combination of SCFs and multiwalled carbon nanotubes (MWNTs) were prepared. Atomic force microscopy observations and contact angle measurement were used to investigate the modification effect of the BMLPO method. Mechanical tests and scanning electron microscopy observations were used to study the effects of the SCFs, MWNTs, and their combination on tensile properties, impact strength, and fracture toughness of the epoxy composites. The results show that the surface roughness of the SCFs after BMLPO treatment increased, and the wettability of the SCFs was improved as well. The combined use of the SCFs and MWNTs had a synergetic effect on the tensile strength, fracture toughness, and impact strength of the epoxy composites. The addition of MWNTs promoted the plastic deformation of the epoxy matrix and decreased the stress‐concentration level near the SCF/matrix interface; these were considered the main causes of the synergetic effect. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43500.     

Mechanical properties of graphene nanoplatelet/epoxy composites

Because of their high‐specific stiffness, carbon‐filled epoxy composites can be used in structural components in fixed‐wing aircraft. Graphene nanoplatelets (GNPs) are short stacks of individual layers of graphite that are a newly developed, lower cost material that often increases the composite tensile modulus. In this work, researchers fabricated neat epoxy (EPON 862 with Curing Agent W) and 1–6 wt % GNP in epoxy composites. The cure cycle used for this aerospace epoxy resin was 2 h at 121°C followed by 2 h at 177°C. These materials were tested for tensile properties using typical macroscopic measurements. Nanoindentation was also used to determine modulus and creep compliance. These macroscopic results showed that the tensile modulus increased from 2.72 GPa for the neat epoxy to 3.36 GPa for 6 wt % (3.7 vol %) GNP in epoxy composite. The modulus results from nanoindentation followed this same trend. For loadings from 10 to 45 mN, the creep compliance for the neat epoxy and GNP/epoxy composites was similar. The GNP aspect ratio in the composite samples was confirmed to be similar to that of the as‐received material by using the percolation threshold measured from electrical resistivity measurements. Using this GNP aspect ratio, the two‐dimensional randomly oriented filler Halpin–Tsai model adjusted for platelet filler shape predicts the tensile modulus well for the GNP/epoxy composites. Per the authors' knowledge, mechanical properties and modeling for this GNP/epoxy system have never been reported in the open literature. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Quantification of carbon nanotube dispersion and its correlation with mechanical and thermal properties of epoxy nanocomposites

An experimental study is carried out to quantitatively assess the dispersion quality of carbon nanotubes (CNTs) in epoxy matrix as a function of CNT variant and weight fraction. To this end, two weight fractions (0.05% and 0.25%) of as-grown, oxidized, and functionalized CNTs are used to process CNT/epoxy nanocomposites. Scanning electron microscopy, X-ray diffraction, and Fourier transform infrared analysis of different variants of CNTs are used to establish the efficiency of purification route. While the relative change in mechanical properties is investigated through tensile and micro-hardness testing, thermal conductivity of different nanocomposites is measured to characterize the effect of CNT addition on the average thermal properties of epoxy. Later on, a quantitative analysis is carried out to establish the relationship between the observed improvements in average composite properties with the dispersion quality of CNTs in epoxy. It is shown that carboxylic (-COOH) functionalization reduces the average CNT agglomerate size and thus ensures better dispersion of CNTs in epoxy even at higher CNT weight fraction. The improved dispersion leads to enhanced interfacial interaction at the CNT/epoxy interface and hence provides higher relative improvement in nanocomposite properties compared to the samples prepared using as-grown and oxidized CNTs. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48879.     

Effects of crosslinking reaction and extension strain on the electrical properties of silicone rubber/carbon nanofiller composites

Stretchable conductive silicone rubber (SR) composites are important in wearable electronic devices and the crosslinking of SR composites is necessary for their applications. But the effect of the crosslinking reaction on the electrical conductivity of SR composites is rarely reported. In this article, the effect of crosslinking reaction on the electrical conductivity of SR composites filled with conductive carbon black, carbon nanotubes, and graphene are studied. The crosslink density of SR composites increases with increasing curing time, but the electrical conductivity decreases sharply at the early stage of crosslinking, especially for SR/conductive carbon black composite, which is ascribed to the reaggregation of conductive nanofillers in SR during the crosslinking process. The elastic modulus of the three SR composites gradually increases while the elongation at break decreases with increasing curing time, and the SR/carbon black composite shows ultra-high elongation at break (1578%). In addition, SR/graphene composite is more sensitive to the extension strain than SR/carbon black and SR/carbon nanotubes composites, and its gauge factor is 414 at the strain ranges of 3–25%. This research work brings a new method to optimize the crosslinking structure of conductive SR composites.     

Role of the degree of acetalization on dynamic mechanical properties of polyvinyl butyral/carbon nanotube composites

In this work, polyvinyl butyral (PVB) nanocomposites reinforced with 0.1–1.0 wt % of pristine [carbon nanotube (CNT)] or oxidized (CNTO) multiwalled CNTs were synthesized via in situ polymerization. It was found that the presence of the reinforcement during the synthesis altered the degree of acetalization of PVB. Dynamic mechanical analyses showed that PVB nanocomposites containing 0.5 wt % of pristine CNT had the best adhesion factor, with increases of about 30% in the storage modulus. On the other hand, PVB/CNTO 1.0 wt % nanocomposites achieved the best reinforcement efficiency factor (“C” coefficient). It is concluded that the in situ polymerization improves dispersion and final properties of the nanocomposite only if the nanoparticles are able to form relevant interfacial interactions during the PVB synthesis. In addition, it was verified that the presence of CNT or CNTO altered the degree of acetalization of PVB, which strongly influences the final properties of the nanocomposites. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48146.     

Electrical,mechanical, and crystallization properties of ethylene‐tetrafluoroethylene copolymer/multiwalled carbon nanotube composites

Multiwalled carbon nanotubes (MWCNTs) were melt‐mixed in a conical twin‐screw extruder with a random copolymer of ethylene and tetrafluoroethylene. Surprisingly, the electrical percolation threshold of the resultant composites was quite low; ～0.9 wt %. In fact, this value is as low or lower than the value for most MWCNT/semicrystalline polymer composites made with roughly equivalent aspect ratio tubes mixed in a similar manner, for example, melt mixing. This low percolation threshold, suggestive of good dispersion, occurred even though the polymer surface energy is quite low which should make tubes more difficult to disperse. Dynamic mechanical measurements confirmed the rather low percolation threshold. The effect of nanotubes on crystallization kinetics was quite small; suggesting perhaps that a lack of nucleation which in turn reduces/eliminates an insulating crystalline polymer layer around the nanotubes might explain the low percolation threshold. Finally, the modulus increased with the addition of nanotubes and the strain at break decreased. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41052.     

Hybridizing MWCNT with nano metal oxides and TiO2 in epoxy composites: Influence on mechanical and thermal performances

In this study, the effects of multi‐walled carbon nanotubes (MWCNT), and its hybrids with iron oxide (Fe₂O₃) and copper oxide (CuO) nanoparticles on mechanical characteristics and thermal properties of epoxy binder was evaluated. Furthermore, simultaneous effects of using MWCNT with TiO₂ as pigment and CaCO₃ as filler for epoxy composites were determined. To investigate effects of nano‐ and micro‐particles on epoxy matrix, the samples were evaluated by TGA and DTA. It was found that the hybrid of MWCNT with nano metal oxides caused considerable increment in the tensile and flexural properties of epoxy samples in comparison to the single MWCNT containing samples at the same filler contents. Significant improvement in the thermal conductivity of epoxy samples was obtained by using TiO₂ pigment along with MWCNT. The TiO₂ pigment also caused considerable improvement in mechanical properties of the epoxy matrix and the MWCNT containing nanocomposite. The best mechanical and thermal properties of epoxy nanocomposites were obtained at 1.5 wt % of MWCNT and 7 wt % of TiO₂ that it should be attributed to particle network forming of the particles which cause better nano/micro dispersion and properties. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43834.     

Simultaneous improvement in strength,toughness, and thermal stability of epoxy/halloysite nanotubes composites by interfacial modification

This work investigated the effect of silane modification of halloysite nanotubes (HNTs) on the mechanical properties of epoxy/HNTs nanocomposites. Three kinds of silane coupling agents, including 3‐(2‐aminoethyl)‐aminopropyltrimethoxysilane (AEAPS), (3‐glycidyloxypropyl)‐trimethoxysilane (GPTMS), and octyltriethoxysilane (OTES), were employed. It was shown that the modified HNTs exhibited a better dispersion in the epoxy matrix compared with pristine one. Because of strong interfacial interaction between AEAPS modified HNTs and the epoxy matrix, the nanocomposites exhibited the highest glass transition temperature and modulus among all the samples. On the other hand, AEAPS and GPTMS modified HNTs/epoxy nanocomposites showed enhanced tensile strength and toughness. The toughing mechanisms were identified by the SEM micrographs of the fracture surfaces of the different kinds of samples. In this study, simultaneous enhancement of strength, toughness, and thermal stability of epoxy by the modified HNTs provides a novel approach to produce high‐performance thermosets. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43249.