Antimicrobial properties and thermal stability of polycarbonate modified with 1‐alkyl‐3‐methylimidazolium tetrafluoroborate ionic liquids

Four water immiscible ionic liquids (ILs): 1‐hexyl‐3‐methylimidazolium tetrafluoroborate, 1‐heptyl‐3‐methylimidazolium tetrafluoroborate, 1‐octyl‐3‐methylimidazolium tetrafluoroborate and 1‐dodecyl‐3‐methylimidazolium tetrafluoroborate have been synthesized. Polycarbonate (PC) films containing ILs were prepared by solvent casting from methylene chloride solutions. Scanning electron microscopy measurements showed the high homogeneity of PC/IL films with the IL content up to 4 wt %. The tendency to IL aggregation was observed for polymeric films with higher IL content (5%). PC/IL composites were found to have the reduced thermal decomposition temperature under both an air and a nitrogen atmosphere in comparison with the neat PC. The effect of IL content on the antimicrobial activity of PC films against Escherichia coli bacteria was studied. Pronounced antimicrobial efficacy was revealed for PC/IL films for all studied ILs starting from 3 wt % of IL. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40050.     

Physical and electrochemical characterizations of poly(vinylidene fluoride‐co‐hexafluoropropylene)/SiO2‐based polymer electrolytes prepared by the phase‐inversion technique

Highly porous poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVdF–HFP)‐based polymer membranes filled with fumed silica (SiO₂) were prepared by a phase‐inversion technique, and films were also cast by a conventional casting method for comparison. N‐Methyl‐2‐pyrrolidone as a solvent was used to dissolve the polymer and to make the slurry with SiO₂. Phase inversion occurred just after the impregnation of the applied slurry on a glass plate into flowing water as a nonsolvent, and then a highly porous structure developed by mutual diffusion between the solvent and nonsolvent components. The PVdF–HFP/SiO₂ cast films and phase‐inversion membranes were then characterized by an examination of the morphology, thermal and crystalline properties, absorption ability of an electrolyte solution, ionic conductivity, electrochemical stability, and interfacial resistance with a lithium electrode. LiPF₆ (1M) dissolved in a liquid mixture of ethylene carbonate and dimethyl carbonate (1:1 w/w) was used as the electrolyte solution. Through these characterizations, the phase‐inversion polymer electrolytes were proved to be superior to the cast‐film electrolytes for application to rechargeable lithium batteries. In particular, phase‐inversion PVdF–HFP/SiO₂ (30–40 wt %) electrolytes could be recommended to have optimum properties for the application. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 140–148, 2006     

Modification of sulfonated poly(ether ether ketone) membranes by impregnation with the ionic liquid 1‐butyl‐3‐methylimidazolium tetrafluoroborate for proton exchange membrane fuel cell applications

Sulfonated poly(ether ether ketone) (SPEEK) membranes were modified by impregnation with the ionic liquid (IL) 1‐butyl‐3‐methylimidazolium tetrafluoroborate (BMI.BF₄) by immersion into an IL aqueous solution for different periods of time. The modified membranes were investigated by thermogravimetric analyses (TGA), differential scanning calorimetry (DSC), ion exchange capacity (IEC), and conductivity. The SPEEK membrane immersed into the IL aqueous solution for 2 min showed greater dimensional and thermal stability than the pristine SPEEK membrane, and achieved higher decomposition temperatures. It also presented a higher conductivity value (1.0 mS cm^?1), indicating that BMI.BF₄ is a promoter of proton conductivity. The membrane electrode assembly (MEA) produced reached maximum values of power density of 0.13 W cm^?2 and current density of 0.54 A cm^?2 during fuel cell operation. The results indicate that the SPEEK membrane modified by immersion for 2 min is promising for use in a proton exchange membrane fuel cell. Its performance yielded values very close to those obtained with Nafion, which reaches maximum values of power density of 0.19 W cm^?2 and current density of 0.77 A cm^?2. POLYM. ENG. SCI. 56:1037–1044, 2016. © 2016 Society of Plastics Engineers     

Evolution of mechanical properties of polypropylene separator in liquid electrolytes for lithium‐ion batteries

Knowledge of the mechanical behaviors of polymeric separators immersed in liquid electrolytes is of great significance for predicting the long‐term performance of lithium batteries with high performance and safety. In terms of tensile tests, heating shrinkage, and dynamic mechanical analysis as well as the essential work of fracture method, the study reported here encompasses a systematic investigation of the mechanical properties of a typical commercial polypropylene separator in mixtures of ethylene carbonate and dimethyl carbonate and lithium hexafluorophosphate (LiPF₆), comparing with the results in ionic liquid (IL) electrolyte composed of lithium tetrafluoroborate (LiBF₄) and 1‐butyl‐3‐methylimidazolium tetrafluoroborate (BMIBF₄) and dry condition. It has been found that liquid electrolytes have obvious negative effect on the dimensional stability at elevated temperature and mechanical properties, especially on crack resistance of the polymer separator. LiBF₄‐BMIBF₄ has much smaller damage on the strength, Young's modulus and fracture toughness of separator than the organic solution except the dynamic modulus at high temperature. Notably, the maximum tensile stress, Young's modulus and the reciprocal of relaxation time of the polymer separator are linearly dependent with strain rate under quasi‐static condition, and the relaxation time has clarified the coupling effect mechanism of liquid electrolyte and loading rate. Moreover, the non‐dimensional viscoelastic constitute equation could perfectly track the tensile behavior of wet and dry separators at different strain rate, and a property model could well characterize the temperature‐dependent storage modulus of polymer separators from rubbery to viscous state. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46441.     

Preparation and properties of cross‐linked poly(ethylene glycol)/poly[(vinylidene fluoride)‐co‐hexafluoropropylene] interpenetrating network‐type electrolytes for secondary lithium batteries

Cross‐linked poly(ethylene glycol)/poly[(vinylidene fluoride)‐co‐hexafluoropropylene] (XPEG/PVDF–HFP) gel‐type polymer electrolyte interpenetrating polymer networks (IPNs) were prepared by cross‐linking the PEG molecules in the presence of PVDF–HFP molecules. Thermal, mechanical, swelling and electrochemical properties, as well as microstructures of the prepared polymer electrolytes, were investigated for various polymer compositions. The mechanical strength increased, but the swelling ratio in electrolyte solution decreased with increasing PVDF–HFP content. The ion conductivity was highly affected by the type of electrolyte salt, and increased with increasing XPEG concentration. The Arrhenius‐type relationship was observed in the temperature dependence of ion conductivity. The polymer electrolyte systems prepared in this study were electrochemically stable up to about 5 V. Copyright © 2005 Society of Chemical Industry     

Preparation and performance study on P(St‐MMA)‐SiO2 doped P(VDF‐HFP) based composite polymer electrolyte

The organic–inorganic hybrid material poly(styrene‐methyl methacrylate)‐silica (P(St‐MMA )‐SiO₂) was successfully prepared by in situ polymerization confirmed by Fourier transform infrared spectroscopy and was employed to fabricate poly(vinylidene fluoride‐hexafluoropropylene) (P(VDF‐HFP )) based composite polymer electrolyte (CPE ) membrane. Desirable CPEs can be obtained by immersing the CPE membranes into 1.0 mol L^?1 LiPF₆‐EC /DMC /EMC (LiPF₆ ethylene carbonate + dimethyl carbonate + ethylmethyl carbonate) liquid electrolyte for about 0.5 h for activation. The corresponding physicochemical properties were characterized by SEM , XRD , electrochemical impedance spectroscopy and charge–discharge cycle testing measurements. The results indicate that the as‐prepared CPEs have excellent properties when the mass ratio of the hybrid P(St‐MMA )‐SiO ₂ particles to polymer matrix P(VDF‐HFP ) reaches 1:10, at which point the SEM analyses show that the as‐prepared P(St‐MMA )‐SiO ₂ particles are uniformly dispersed in the membrane and the CPE membrane presents a homogeneous surface with abundant interconnected micropores. The XRD results show that there may exist interaction forces between the P(St‐MMA )‐SiO ₂ particles and the polymer matrix, which can obviously decrease the crystallinity of the composite membrane. Moreover, the ionic conductivity at room temperature and the electrochemical working window of the CPE membrane can reach 3.146 mS cm^?1 and 4.7 V, respectively. The assembled LiCoO₂/CPE /Li coin cell with the CPE presents excellent charge–discharge and C ‐rate performance, which indicates that P(St‐MMA )‐SiO ₂ hybrid material is a promising additive for the P(VDF‐HFP ) based CPE of the lithium ion battery. © 2016 Society of Chemical Industry     

Preparation and properties of water‐soluble polyester surfactants. I. Preparation and surface activity of poly(ethylene glycol)‐dimethyl 5‐sulfo‐isophthalate sodium salt polyester surfactants

The reaction of poly(ethylene glycol) (PEG, number‐average molecular weight M_n = 400‐2000) and dimethyl 5‐sulfoisophthalate sodium salt (SIPM) synthesized a series of anionic polymeric surfactants having a range of molecular weights. ¹H‐NMR, FTIR, and elemental analysis were employed to characterize the structures of these compounds. Also, the influences of the PEG segment lengths of PEG/SIPM copolymers on the surface tension, foaming properties, wetting power, and dispersant properties were investigated. The experimental results indicated that the solution that contained the PEG/SIPM copolymer surfactants exhibited excellent surface‐active properties. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2727–2731, 2002     

Preparation of electrorheological active ionomers from poly(2‐hydroxyethyl methacrylate)‐co‐poly(4‐vinyl pyridine)

In this study, synthesis, characterization, partial hydrolysis, and salt formation of poly(2‐hydroxyethyl methacrylate)‐co‐poly(4‐vinyl pyridine), (poly(HEMA)‐co‐poly‐(4‐VP)) copolymers were investigated. The copolymers were synthesized by free radical polymerization using K₂S₂O₈ as an initiator. By varying the monomer/initiator ratio, chain lengths of the copolymers were changed. The copolymers were characterized by gel permeation chromatography (GPC), viscosity measurements, ¹H and ¹³C NMR and FTIR spectroscopies, elemental analysis, and end group analysis methods. The copolymers were partially hydrolyzed by p‐toluene sulfonic acid monohydrate (PTSA·H₂O) and washed with LiOH_(aq) solution to prepare electrorheological (ER) active ionomers, poly(Li‐HEMA)‐co‐poly(4‐VP). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3540–3548, 2006     

Palladium(II)‐Catalyzed 1,4‐Addition of Arylboronic Acids to β‐Arylenones for Enantioselective Synthesis of 4‐Aryl‐4H‐chromenes

The enantioselective 1,4‐addition of arylboronic acids to β‐arylenones to give β‐diaryl ketones was carried out at 0–25 °C in the presence of a dicationic palladium(II) catalyst, [Pd(S,S‐chiraphos)(PhCN)₂](SbF₆)₂. Addition of a silver salt such as silver tetrafluoroborate [AgBF₄] or silver hexafluoroantimonate [AgSbF₆] (5–10 mol %) was effective to achieve high enantioselectivities at low temperatures (92–99 % ee) and to reduce the catalyst loading to 0.05 mol %. The protocol provided a simple access to 4‐aryl‐4H‐chromenes. Optically active chromenes were synthesized with up to 99 % ee via dehydration of the 1,4‐adducts between arylboronic acids and β‐(2‐hydroxyaryl)‐α,β‐unsaturated ketones.     

Performances of poly(vinylidene fluoride‐co‐hexafluoropropylene) ultrafiltration membranes modified with poly(vinyl pyrrolidone)

The structure and performance of modified poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVdF‐co‐HFP) ultra‐filtration membranes prepared from casting solutions with different concentrations of poly(vinyl pyrrolidone) (PVP) were investigated in this study. Membrane properties were studied in terms of membrane compaction, pure water flux (PWF), water content (WC), membrane hydraulic resistance ( R _m), protein rejection, molecular weight cut‐off (MWCO), average pore size, and porosity. PWF, WC, and thermal stability of the blend membranes increased whereas the crystalline nature and mechanical strength of the blend membranes decreased when PVP additive concentration was increased. The contact angle (CA) decreased as the PVP concentration increased in the casting solution, which indicates that the hydro‐philicity of the surface increased upon addition of PVP. The average pore size and porosity of the PVdF‐co‐HFP membrane increased to 42.82 Å and 25.12%, respectively, when 7.5 wt% PVP was blended in the casting solution. The MWCO increased from 20 to 45 kDa with an increase in PVP concentration from 0 to 7.5 wt%. The protein separation study revealed that the rejection increased as the protein molecular weight increased. The PVdF‐co‐HFP/PVP blended membrane prepared from a 7.5 wt% PVP solution had a maximum flux recovery ratio of 74.3%, which explains its better antifouling properties as compared to the neat PVdF‐co‐HFP membrane. POLYM. ENG. SCI., 55:2482–2492, 2015. © 2015 Society of Plastics Engineers     

Synthesis and characterization of poly(thiophen‐3‐yl acetic acid 4‐pyrrol‐1‐yl phenyl ester‐co‐N‐methylpyrrole) and its application in an electrochromic device

Copolymer of thiophen‐3‐yl acetic acid 4‐pyrrol‐1‐yl phenyl ester (TAPE) with N‐methylpyrrole (NMPy) was synthesized by potentiostatic electrochemical polymerization in acetonitrile–tetrabutylammonium tetrafluoroborate solvent–electrolyte couple. The chemical structures were confirmed via Fourier transform infrared spectroscopy (FTIR), cyclic voltammetry (CV), and UV–vis spectroscopy. Electrochromic and spectroelectrochemical properties of poly(TAPE‐co‐NMPy) [P(TAPE‐co‐NMPy)] were investigated. Results showed that the copolymer revealed color change between light yellow and green upon doping and dedoping of the copolymer, with a moderate switching time. Furthermore, as an application, dual‐type absorptive/transmissive polymer electrochromic device (ECD) based on poly(TAPE‐co‐NMPy) and poly(3,4‐ethylene dioxythiophene) (PEDOT) have been assembled, where spectroelectrochemistry, switching ability, stability, and optical memory of the ECD were investigated. Results showed that the device exhibited good optical memory and stability with moderate switching time. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1988–1994, 2006     

Synthesis and ferroelectric investigations of poly(vinylidene fluoride‐co‐hexafluoropropylene)‐Mg(NO3)2 films

The free‐standing, flexible, and ferroelectric films of poly(vinylidenefluoride‐co‐hexafluoropropylene) [P(VDF‐HFP)] were prepared by spin coating method. The ferroelectric phase of the films was enhanced by adding magnesium nitrate Mg(NO₃)₂ in different wt % as the additive during the film fabrication. The effects on the structural, compositional, morphological, ferroelectric, dielectric, and leakage current behaviors of the films due to the addition of salt were analyzed. Based on the X‐ray diffraction (XRD) patterns and Fourier Transform Infrared (FTIR) spectra, it is confirmed that the addition of Mg(NO₃)₂ promotes the electroactive β phase that induces the ferroelectric property. The fiber‐like topography of the films exhibits a nodule‐like structure, and the roughness of the films increases by the addition of Mg(NO₃)₂. The ferroelectric studies show the higher polarization values for the composite films than that of the plain P(VDF‐HFP) film. The Piezo‐response force microscope images also confirm the domain switching behavior of the samples. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44008.     

Diels–Alder‐based crosslinked self‐healing polyurethane/urea from polymeric methylene diphenyl diisocyanate

Crosslinked self‐healing polyurethane/urea based on a Diels–Alder reaction (C‐PMPU–DA) was synthesized from a multiple‐furan monomer and a commercial bismaleimide. The multiple‐furan monomer (PMPU–furan) was obtained from a functionalized prepolymer (polymeric MDI: PBA‐2000 = 2:1) by furfuryl amine. The structures of both the PMPU–furan and C‐PMPU–DA were characterized by attenuated total reflectance (ATR)–Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry, thermogravimetric analysis, and ¹H‐NMR. The Diels–Alder bonds enabled C‐PMPU–DA thermal reversibility, which was investigated by ATR–FTIR spectroscopy, ¹H‐NMR, gel–solution–gel experiments, and viscosity tests. Meanwhile, the self‐healing properties of C‐PMPU–DA were also investigated by the recovery of the mechanical properties. The results showed that C‐PMPU–DA exhibited good thermal reversibility and self‐healing properties. C‐PMPU–DA exhibited thermosetting properties at room temperature, although it exhibited thermoplastic properties at higher temperatures and may find applications in self‐healing materials, recyclable materials, or removable materials. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40234.     

Grafting of 4‐Hydroxybenzenesulfonic Acid onto Commercially Available Poly(VDF‐co‐HFP) Copolymers for the Preparation of Membranes

The grafting of a phenate bearing sulfonate group in solution onto commercially available poly(VDF‐co‐HFP) copolymers, where VDF and HFP stand for vinylidene fluoride and hexafluoropropene, respectively, is presented. This reaction leads to novel fluoropolymers, bearing aryl sulfonic acid side functions, which are fuel cell membrane precursors. A mechanism similar to the grafting of bisphenol onto VDF‐containing copolymers is discussed. First, the sulfonate phenate is modified to give the didecyldimethylammonium bromide sulfonate phenate salt, in order to promote the substitution onto a fluorine atom in VDF unit adjacent to one HFP unit onto a fluorine atom in the copolymer. The substitution of this salt onto the fluorinated copolymer yields low molar percentages of grafted phenate, ranging from 1.8 to 5.1 mol‐%, whereas it reaches values up to 13 mol‐% grafting when the NH₂‐CH₂‐CH₂‐S‐CH₂‐CH₂‐C₆H₄‐SO₃Na amine is used as the grafting agent. NMR characterization is used to monitor the grafting process. The electrochemical properties of the resulting phenate grafted‐poly(VDF‐co‐HFP) copolymer are studied. The theoretical ion exchange capacities are half that of Nafion®. The proton conductivities are also lower than that of Nafion®, although one conductivity measurement reached a value of 5.1 mS cm^–1, showing a non‐negligible conductivity. The water uptake is lower than these noted for a sulfonated amine‐grafted copolymer, and is of the same order as that for Nafion®. Finally, it is shown that these novel materials start to decompose above 200 °C, showing a similar thermostability as that of an amino‐containing aryl sulfonate‐grafted poly(VDF‐co‐HFP) copolymer.     

Organic‐acid‐catalyzed sol–gel route for preparing poly(methyl methacrylate)–silica hybrid materials

In this study, a series of organic–inorganic hybrid sol–gel materials consisting of a poly(methyl methacrylate) (PMMA) matrix and dispersed silica (SiO₂) particles were successfully prepared through an organic‐acid‐catalyzed sol–gel route with N‐methyl‐2‐pyrrolidone as the mixing solvent. The as‐synthesized PMMA–SiO₂ nanocomposites were subsequently characterized with Fourier transform infrared spectroscopy and transmission electron microscopy. The solid phase of organic camphor sulfonic acid was employed to catalyze the hydrolysis and condensation (i.e., sol–gel reactions) of tetraethyl orthosilicate in the PMMA matrix. The formation of the hybrid membranes was beneficial for the physical properties at low SiO₂ loadings, especially for enhanced mechanical strength and gas barrier properties, in comparison with the neat PMMA. The effects of material composition on the thermal stability, thermal conductivity, mechanical strength, molecular permeability, optical clarity, and surface morphology of the as‐prepared hybrid PMMA–SiO₂ nanocomposites in the form of membranes were investigated with thermogravimetric analysis, differential scanning calorimetry, dynamic mechanical analysis, gas permeability analysis, ultraviolet–visible transmission spectroscopy, and atomic force microscopy, respectively. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and characterization of temperature‐sensitive block copolymers from poly(N‐isopropylacrylamide) and 4‐methyl‐ε‐caprolactone or 4‐phenyl‐ε‐caprolactone

This study synthesizes thermally sensitive block copolymers poly(N‐isopropylacrylamide)‐b‐poly(4‐methyl‐ε‐caprolactone) (PNIPA‐b‐PMCL) and poly(N‐isopropylacrylamide)‐b‐poly(4‐phenyl‐ε‐caprolactone) (PNIPA‐b‐PBCL) by ring‐opening polymerization of 4‐methyl‐ε‐caprolactone (MCL) or 4‐phenyl‐ε‐caprolactone (BCL) initiated from hydroxy‐terminated poly(N‐isopropylacrylamide) (PNIPA) as the macroinitiator in the presence of SnOct₂ as the catalyst. This research prepares a PNIPA bearing a single terminal hydroxyl group by telomerization using 2‐hydroxyethanethiol (ME) as a chain‐transfer agent. These copolymers are characterized by differential scanning calorimetry (DSC), ¹H‐NMR, FTIR, and gel permeation chromatography (GPC). The thermal properties (T_g) of diblock copolymers depend on polymer compositions. Incorporating larger amount of MCL or BCL into the macromolecular backbone decreases T_g. Their solutions show transparent below a lower critical solution temperature (LCST) and opaque above the LCST. LCST values for the PNIPA‐b‐PMCL aqueous solution were observed to shift to lower temperature than that for PNIPA homopolymers. This work investigates their micellar characteristics in the aqueous phase by fluorescence spectroscopy, transmission electron microscopy (TEM), and dynamic light scattering (DLS). The block copolymers formed micelles in the aqueous phase with critical micelle concentrations (CMCs) in the range of 0.29–2.74 mg L^?1, depending on polymer compositions, which dramatically affect micelle shape. Drug entrapment efficiency and drug loading content of micelles depend on block polymer compositions. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Electrospun nanofiber‐coated separator membranes for lithium‐ion rechargeable batteries

Nanofiber‐coated composite membranes were prepared by electrospinning polyvinylidene fluoride‐co‐chlorotrifluoroethylene (PVDF‐co‐CTFE) and PVDF‐co‐CTFE/polyvinylidene fluoride‐co‐hexafluoropropylene (PVDF‐co‐HFP) onto six different Celgard® microporous battery separator membranes. Application of a PVDF‐based copolymer nanofiber coating onto the surface of the battery separator membrane provides a method for improving the electrolyte absorption of the separator and the separator‐electrode adhesion. Peel tests showed that both PVDF‐co‐CTFE and PVDF‐co‐CTFE/PVDF‐co‐HFP nanofiber coatings have comparable adhesion to the membrane substrates. Electrolyte uptake capacity was investigated by soaking the nanofiber‐coated membranes in a liquid electrolyte solution. PVDF‐co‐CTFE and PVDF‐co‐CTFE/PVDF‐co‐HFP nanofiber‐coated membranes exhibited higher electrolyte uptake capacities than uncoated membranes. It was also found that PVDF‐co‐CTFE nanofiber‐coated membranes have higher electrolyte uptakes than PVDF‐co‐CTFE/PVDF‐co‐HFP nanofiber‐coated membranes due to the smaller diameters of PVDF‐co‐CTFE nanofibers and higher polarity of PVDF‐co‐CTFE. The separator–electrode adhesion properties were also investigated. Results showed PVDF‐co‐CTFE and PVDF‐co‐CTFE/PVDF‐co‐HFP nanofiber coatings improved the adhesion of all six membrane substrates to the electrode. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis and characterization of novel biodegradable polymeric prodrugs containing 5‐fluorouracil and 4‐amino‐N‐(2‐pyrimidinyl) benzene sulfonamide terminal groups

To develop novel biodegradable polymeric prodrugs with target‐directing and drug‐active functional groups, a series of polymeric antitumor prodrugs containing sulfadiazine and 5‐fluorouracil terminal groups were prepared via the two‐step reaction of chlorinated poly(lactic acid) or chlorinated poly(lactic acid‐co‐glycolic acid) with potassium sulfadiazine (SF‐K) and 1,3‐dihydroxymethyl‐5‐fluorouracil. The synthesized polymers were characterized by means of infrared spectroscopy, proton nuclear magnetic resonance spectroscopy, gel permeation chromatography, viscosity measurements, differential scanning calorimetry, and ultraviolet (UV) spectroscopy. The GA/LA value was varied, so that the effects of the comonomer content on the solubility, thermal properties, and degradable behaviors were examined respectively. It was found that introducing the GA units could increase the melting temperature (T_m), the hydrolytic degradation, and the hydrophilicity, while it decreased the glass transition temperature (T_g). The drug content of 5‐FU measured by UV spectra is 56.3 in maximum. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Separation of α‐Lactalbumin and β‐Lactoglobulin by a Convenient Liquid‐Solid Extraction System: Application to Milk Whey

A liquid‐solid extraction system based on Tween 80/phosphate was developed. Under the optimized conditions (9 wt % Tween 80, 1.6 : 1 (molar ratio) K₂HPO₄ : NaH₂PO₄, 1.25 mol/L total phosphate, pH = 7.4), α‐Lactalbumin (α‐La) and β‐Lactoglobulin (β‐Lg) were separated with recovery rates of 87.6 % (in the solid polymeric phase) and 98.2 % (in the salt aqueous phase), respectively. Under the effects of water and salt, the solid phase had the ability to form a new liquid‐solid extraction system, and 85.1 % of α‐La could be reversely extracted into the new salt aqueous phase. Following dialysis against water, proteins obtained through extraction and reverse extraction, were analyzed by polyacrylamide gel electrophoresis (PAGE) and thin‐layer scanning. The method was applied successfully to separate α‐La and β‐Lg from milk whey.     

Microstructure and properties of novel fluorescent pyrene functionalized PANI/P(VDF‐HFP) blend

We herein report the preparation and properties of the first polymer blend using pyrene functionalized polyaniline (pf‐PANI). The pf‐PANI has been synthesized and its blend has been prepared with the copolymer of vinylidene fluoride and hexafluoropropylene P(VDF‐HFP). The FTIR results reveal intermolecular interaction between the polar amide group of pf‐PANI and the polarized CH₂ group of P(VDF‐HFP). The crystalline phase of PVDF of the copolymer revealed a transformation from α to β crystalline form after blending with pf‐PANI, as found from FTIR and XRD measurements. The calorimetric measurements together with DMA results revealed the blend is partially miscible. The SEM measurements showed that the pf‐PANI has been dispersed uniformly in the P(VDF‐HFP) matrix. The solution photoluminescence spectrum of the pf‐PANI exhibited emission in the purple–blue region and is slightly red shifted for the blend. The possible applications of this flexible fluorescent pf‐PANI/P(VDF‐HFP) has been suggested. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40162.