Structural and mechanical characterization of poly(ether ether ketone) (PEEK) and sulfonated PEEK films: Effects of thermal history,sulfonation, and preparation conditions

In this work, virgin and sulfonated poly(ether ether ketone) films (PEEK and SPEEK, respectively) have been studied by dynamic mechanical analysis, modulated differential scanning calorimetry, wide‐angle X‐ray diffraction, birefringence, and optical microscopy. The properties of the unmodified polymer have been addressed to assess the original morphological characteristics and the changes induced by sulfonation. In general, the introduction of ionic groups in the polymer backbone alters dramatically the intrinsic properties of the parent material. The particular thermomechanical response exhibited by PEEK and SPEEK samples, characterized by a hysteresis loop, can be explained by the reversible and irreversible relaxation–orientation of the microstructure, even in the sub‐T_g region. The results showed that the preparation conditions largely determine the nonequilibrium morphological features of both compression‐molded PEEK films and solvent‐cast SPEEK membranes. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 756–774, 2006     

Synthesis and characterization of poly(ether amide ether ketone)/poly(ether ketone ketone) copolymers

A new monomer, N,N′‐bis(4‐phenoxybenzoyl)‐m‐phenylenediamine (BPPD), was prepared by condensation of m‐phenylenediamine with 4‐phenoxybenzoyl chloride in N,N‐dimethylacetamide (DMAc). A series of novel poly(ether amide ether ketone) (PEAEK)/poly(ether ketone ketone) (PEKK) copolymers were synthesized by the electrophilic Friedel‐Crafts solution copolycondensation of terephthaloyl chloride (TPC) with a mixture of diphenyl ether (DPE) and BPPD, over a wide range of DPE/BPPD molar ratios, in the presence of anhydrous AlCl₃ and N‐methylpyrrolidone (NMP) in 1,2‐dichloroethane (DCE). The influence of reaction conditions on the preparation of copolymers was examined. The copolymers obtained were characterized by different physicochemical techniques. The copolymers with 10–25 mol % BPPD were semicrystalline and had remarkably increased T_gs over commercially available PEEK and PEKK due to the incorporation of amide linkages in the main chains. The copolymers III and IV with 20–25 mol % BPPD had not only high T_gs of 184–188°C, but also moderate T_ms of 323–344°C, having good potential for the melt processing. The copolymers III and IV had tensile strengths of 103.7–105.3 MPa, Young's moduli of 3.04–3.11 GPa, and elongations at break of 8–9% and exhibited outstanding thermal stability and good resistance to organic solvents. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Fine poly(ether ether ketone) powders

The physical form of polymers is often important for carrying out subsequent processing operations. For example, fine powders are desirable for molding and sintering compounds because they consolidate to produce void free components. The objective of this work is to prepare fine polymeric particulates suitable for processing into fiber reinforced polymer matrix composites. Micron size particles of poly(ether ether ketone) (PEEK) were prepared by rapidly quenching solutions of these materials. PEEK pellets were dissolved at temperatures near the PEEK melting point in a mixture of terphenyls and quaterphenyls; then the solution was quenched to a temperature between the T_g and T_m (≈ 225°C) by adding a room temperature eutectic mixture of diphenyl ether and biphenyl. A supersaturated, metastable solution of PEEK resulted, causing rapid nucleation. Fine PEEK particles rapidly crystallized from this solution. The average particle size was measured using transmission electron microscopy, atomic force microscopy, and by light scattering of aqueous suspensions which had been fractionated by centrifugation. The average particle diameter was about 0.6 μm. Three dimensional photomicrographs obtained via atomic force microscopy showed some aggregates in the suspensions. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 63: 1571–1578, 1997     

The isothermal crystallization of poly(ether ether ketone) by two‐dimensional differential scanning calorimetry correlation mapping

This article reports the first application of the two‐dimensional differential scanning calorimetry correlation mapping, two‐dimensional‐DSC‐CM to analyze DSC rate–time data of PEEK. This provided evidence that the isothermal crystallization reduced rate–time curves exhibited fractional n values when analyzed by the Avrami equation. These fractional n values, which increased with temperature, were consistent with the presence of two processes, primary and secondary crystallization, with an increasing contribution of the secondary crystallization to the overall crystallinity. In contrast to the known literatures, secondary crystallization was observed to proceed at early stage of primary crystallization. The study of the effect of proton irradiation, up to a dose of 9.9 MGy, showed that the fractional n value was below 3.0, and does not appear to be temperature dependent. DSC analysis of the crystallization kinetics, combined with two‐dimensional correlation mapping proved a powerful tool for investigating irradiation damage of PEEK. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44378.     

Synthesis and properties of copolymers of poly(ether ketone ketone) and poly(ether amide ether amide ether ketone ketone)

Poly(aryl ether ketone)s (PAEKs) are a class of high‐performance engineering thermoplastics known for their excellent combination of chemical, physical and mechanical properties, and the synthesis of semicrystalline PAEKs with increased glass transition temperatures (T_g) is of much interest. In the work reported, a series of novel copolymers of poly(ether ketone ketone) (PEKK) and poly(ether amide ether amide ether ketone ketone) were synthesized by electrophilic solution polycondensation of terephthaloyl chloride with a mixture of diphenyl ether and N,N′‐bis(4‐phenoxybenzoyl)‐4,4′‐diaminodiphenyl ether (BPBDAE) under mild conditions. The copolymers obtained were characterized using various physicochemical techniques. The copolymers with 10–35 mol% BPBDAE are semicrystalline and have markedly increased T_g over commercially available poly(ether ether ketone) and PEKK due to the incorporation of amide linkages in the main chain. The copolymers with 30–35 mol% BPBDAE not only have high T_g of 178–186 °C, but also moderate melting temperatures of 335–339 °C, having good potential for melt processing. The copolymers with 30–35 mol% BPBDAE have tensile strengths of 102.4–103.8 MPa, Young's moduli of 2.33–2.45 GPa and elongations at break of 11.7–13.2%, and exhibit high thermal stability and good resistance to organic solvents. Copyright © 2010 Society of Chemical Industry     

Synthesis and characterization of poly(ether ketone ether ketone ketone)/poly(ether ether ketone ketone) copolymers containing naphthalene and pendant cyano groups

2,6‐Bis(β‐naphthoxy)benzonitrile (BNOBN) was synthesized by reaction of β‐naphthol with 2,6‐difluorobenzonitrile in N‐methyl‐2‐pyrrolidone (NMP) in the presence of KOH and K₂CO₃. Poly(ether ketone ether ketone ketone)(PEKEKK) /poly(ether ether ketone ketone) (PEEKK) copolymers containing naphthalene and pendant cyano groups were obtained by electrophilic Friedel‐Crafts polycondensation of terephthaloyl chloride (TPC) with varying mole proportions of 4,4′‐diphenoxybenzophenone (DPOBP) and 2,6‐bis(β‐naphthoxy)benzonitrile (BNOBN) using 1,2‐dichloroethane (DCE) as solvent and NMP as Lewis base in the presence of anhydrous AlCl₃. The resulting polymers were characterized by various analytical techniques, such as FTIR, DSC, TG, and WAXD. The results indicated that the crystallinity and melting temperature of the polymers decreased with increase in concentration of the BNOBN units in the polymer, the glass transition temperature of the polymers increased with increase in concentration of the BNOBN units in the polymer. Thermogravimetric studies showed that all the polymers were stable up to 536°C in N₂ atmosphere. The copolymers have good resistance to acidity, alkali, and organic solvents. Because of the melting temperature (T_m) depression with increase in the BNOBN content in the reaction system, the processability of the resultant coplymers could be effectively improved. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and properties of poly(aryl ether ketone ketone)/poly(aryl ether ether ketone ketone) copolymers with pendant cyano groups

2,6‐Diphenoxybenzonitrile (DPOBN) was synthesized by reaction of phenol with 2,6‐difluorobenzonitrile in N‐methyl‐2‐pyrrolidone in the presence of KOH and K₂CO₃. Poly(aryl ether ketone ketone)/poly(aryl ether ether ketone ketone) copolymers with pendant cyano groups were prepared by the Friedel–Crafts electrophilic substitution reaction of terephthaloyl chloride with varying mole proportions of diphenyl ether and DPOBN using 1,2‐dichloroethane as solvent and N‐methyl‐2‐pyrrolidone as Lewis base in the presence of anhydrous AlCl₃. The resulting polymers were characterized by various analytical techniques, such as FT‐IR, differential scanning calorimeter, thermal gravimetric analysis, and wide‐angle X‐ray diffraction. The crystallinity and melting temperature of the polymers were found to decrease with increase in concentration of the DPOBN units in the polymer. Thermogravimetric studies showed that all the polymers were stable up to 514°C in N₂ atmosphere. The glass transition temperature was found to increase with increase in concentration of the DPOBN units in the polymer when the molar ratios of DPOBN to DPE ranged from 10/90 to 30/70. The copolymers containing 30–40 mol % of the DPOBN units exhibit excellent thermostability at (350 ± 10)°C and have good resistance to acidity, alkali, and organic solvents. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 3601–3606, 2007     

Synthesis and properties of thio‐containing poly(ether ether ketone)s

A series of thio‐containing poly(ether ether ketone) (PEESK) polymers was synthesized by the introduction of thio groups from 4,4′ thiodiphenol (TDP) into the poly(ether ether ketone) (PEEK) structure via reaction between the phenol and aromatic fluoride groups. The effect of the thio groups on the properties of the PEESK materials was investigated. Differential scanning calorimetry (DSC) analysis and X‐ray diffraction (XRD) patterns show a depression in the crystallinity of the PEESKs with incorporation of the content of thio groups in the backbones. The crystalline structure was identified as an orthorhombic structure with lattice constants of a = 7.52 Å, b = 5.86 Å and c = 10.24 Å for all crystallizable PEESKs. The crystalline structures of the thio‐containing PEEK polymers were the same as that of the neat PEEK, which means the thio‐containing block in the whole thio‐containing PEEK molecule is almost excluded from the crystalline structure and the crystals are completely formed by ‘non‐thio’ blocks only. Due to the glass transition temperature (T_g) and melting temperature (T_m) depression with increase in the TDP content in the reaction system, the processability of the resultant thio‐containing PEEKs could be effectively improved. Copyright © 2004 Society of Chemical Industry     

Rheological properties in blends of poly(aryl ether ether ketone) and liquid crystalline poly(aryl ether ketone)

Rheological properties of the blends of poly(aryl ether ether ketone) (PEEK) with liquid crystalline poly(aryl ether ketone) containing substituted 3‐trifluoromethylbenzene side group (F‐PAEK), prepared by solution precipitation, have been investigated by rheometer. Dynamic rheological behaviors of the blends under the oscillatory shear mode are strongly dependent on blend composition. For PEEK‐rich blends, the systems show flow curves similar to those of the pure PEEK, i.e., dynamic storage modulus G′ is larger than dynamic loss modulus G″, showing the feature of elastic fluid. For F‐PAEK‐rich systems, the rheological behavior of the blends has a resemblance to pure F‐PAEK, i.e., G″ is greater than G′, showing the characteristic of viscous fluid. When the PEEK content is in the range of 50–70%, the blends exhibit an unusual rheological behavior, which is the result of phase inversion between the two components. Moreover, as a whole, the complex viscosity values of the blends are between those of two pure polymers and decrease with increasing F‐PAEK content. However, at 50% weight fraction of PEEK, the viscosity‐composition curves exhibit a local maximum, which may be mainly attributed to the phase separation of two components at such a composition. The changes of G′ and G″ with composition show a trend similar to that of complex viscosity. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4040–4044, 2006     

Crystal structure and drawing‐induced polymorphism in poly(aryl ether ether ketone). IV

A new crystal modification induced by strain and denoted as form II exists alongside the dominant form I structure in the uniaxially oriented poly(ether ether ketone) (PEEK) and the related polymers. The crystal structure of form II for PEEK is also found to possess a two‐chain orthorhombic packing with unit cell parameters of a equal to 0.475 nm, b equal to 1.060 nm, and c equal to 1.086 nm. More extended and flattened chain conformation of form II relative to that of form I is expected to account for an 8% increase in c‐axis dimension, which is attributed to the extensional deformation fixed in situ through strain‐induced crystallization during uniaxial drawing. Annealing experiments suggest that form II is thermodynamically metastable and can be transformed into more stable form I by chain relaxation and reorganization at elevated temperature without external tension. This strain‐induced polymorphism exists universally in the poly(aryl ether ketone) family. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 237–243, 1999     

Preparation of honeycomb films from nitryl poly(ether ether ketone)s via water‐droplet templating

The fabrication of honeycomb‐patterned films from nitryl poly(ether ether ketone)s (PEEK‐NO₂) in a high‐humidity atmosphere was reported in this article. PEEK‐NO₂ was prepared through acid (nitric acid and sulfuric acid) nitration from poly(ether ether ketone)s (PEEK). The obtained polymer, which was characterized by Fourier transform infrared (FT‐IR), X‐ray diffraction (XRD), and differential scanning calorimetry (DSC) showed excellent solubility and thermal stability. Some influence factors on the pattern formation and the fabrication of the porous structure, such as the solution concentration, the solvent, and the atmosphere humidity, were investigated. The results showed that with the increase of the solution concentration, the aperture of the film diminished gradually; the lower the solvents´ boiling point were, the smaller the films´ apertures were and the more regular the pores´ arrange; only under high‐humidity circumstances could obvious and ordered honeycomb films be formed. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and characterization of poly(ether ketone ketone) (PEKK)/sodium sulfonated poly(arylene ether ketone) (S‐PAEK) block copolymers

A series of well‐defined poly(ether ketone ketone) (PEKK)/sodium sulfonated poly(aryl ether ketone) (S‐PAEK) block copolymers of high molecular weights was prepared by direct nucleophilic polymerization of hydroquinone with sodium 5,5′‐carbonylbis(2‐fluorobenzene sulfonate) ( 1 ) and PEKK oligomer ( 2 ). Varying the ratio of 1 to 2 used in polymerization can be used to control the degree of polymer sulfonation, which correspondingly affects the polymer solubility in solvents. Increasing content of 1 in the copolymers, slightly decreases their thermal stability which is nevertheless thermally stable up to 400 °C. Two T_g values, or one broad T_g, were observed in the DSC measurements of the block copolymers, indicating the existence of phase separation, which was further proved by phase‐separated morphologies as shown in atomic force microscopy images. © 2001 Society of Chemical Industry     

Miscibility and crystallization behavior of poly(ether ether ketone ketone)/poly(ether imide) blends

The miscibility and crystallization behavior of poly(ether ether ketone ketone) (PEEKK)/poly(ether imide) (PEI) blends prepared by melt‐mixing were investigated by differential scanning calorimetry. The blends showed a single glass transition temperature, which increased with increasing PEI content, indicating that PEEKK and PEI are completely miscible in the amorphous phase over the studied composition range (weight ratio: 90/10–60/40). The cold crystallization of PEEKK blended with PEI was retarded by the presence of PEI, as is apparent from the increase of the cold crystallization temperature and decrease of the normalized crystallinity for the samples anealed at 300°C with increasing PEI content. Although the depression of the apparent melting temperature of PEEKK blended with PEI was observed, there was no evidence of depression in the equilibrium melting temperature. The analysis of the isothermal crystallization at 313–321°C from the melt of PEEKK/PEI (100/0, 90/10, and 80/20) blends suggested that the retardation of crystallization of PEEKK is caused by the increase of the crystal surface free energy in addition to the decrease of the mobility by blending PEI with a high glass transition temperature. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 769–775, 2001     

Synthesis and characterization of sulfonated poly(phthalazinone ether sulfone ketone) for ultrafiltration and nanofiltration membranes

Modification of poly(phthalazinone ether sulfone ketone) (PPESK) by sulfonation with concentrated or fuming sulfuric acid as sulfonation agents was carried out to prepare membrane materials with increased hydrophilicity and potentially increased fouling resistance. Sulfonated PPESK (SPPESK) copolymers, with a degree of sulfonation ranging from 10–300%, were prepared and characterized. Factors affecting the sulfonation reaction were studied, and reaction conditions for the preparation of SPPESK with different degrees of sulfonation were determined. Compared with the properties of PPESK, the hydrophilicity of SPPESK was increased, as shown by a reduced contact angle with water. The glass transition temperature was increased from 278°C (PPESK) to a maximum of 323°C for the highly sulfonated derivative, due to the strong polarity of  SO₃H and hydrogen bonding. Ultrafiltration membranes prepared with PPESK and SPPESK were compared. For a SPPESK asymmetric membrane, the PEG12000 rejection was 98% and the water flux was 876 kg · m⁻² · h⁻¹. SPPESK/PPESK composite nanofiltration membranes were also prepared and were shown to have short‐term operational stability up to 120°C. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1685–1692, 2001     

Thermal properties of melt‐blended poly(ether ether ketone) and poly(ether imide)

The thermal properties of blends of poly(ether ether ketone) (PEEK) and poly(ether imide) (PEI) prepared by screw extrusion were investigated by differential scanning calorimetry. From the thermal analysis of amorphous PEEK–PEI blends which were obtained by quenching in liquid nitrogen, a single glass transition temperature (T_g) and negative excess heat capacities of mixing were observed with the blend composition. These results indicate that there is a favorable interaction between the PEEK and PEI in the blends and that there is miscibility between the two components. From the Lu and Weiss equation and a modified equation from this work, the polymer–polymer interaction parameter (χ₁₂) of the amorphous PEEK–PEI blends was calculated and found to range from −0.058 to −0.196 for the extruded blends with the compositions. The χ₁₂ values calculated from this work appear to be lower than the χ₁₂ values calculated from the Lu and Weiss equation. The χ₁₂ values calculated from the T_g method both ways decreased with increase of the PEI weight fraction. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 733–739, 1999     

Preliminary investigation of poly(ether sulfone)/poly(aryl ether ketone) containing 1,4‐naphthalene blends

The blends of poly(ether sulfone) and poly(aryl ether ketone) containing 1,4‐naphthalene were prepared by melt mixing in a Brabender‐like apparatus. The specimens for measurements were made by compression molding under pressure and then were water‐quenched at room temperature. The tensile strength, tensile modulus, elongation at break, thermal analysis, and scanning electron microscopy were each measured. The dependence of tensile strength, tensile modulus, and elongation at break on blend systems was obtained. The effects of composition and miscibility on the mechanical properties are discussed. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 472–476, 2006     

Compatibility studies of sulfonated poly(ether ether ketone)–poly(ether imide)–polycarbonate ternary blends

Binary blends of the sulfonated poly(ether ether ketone) (SPEEK)–poly(ether imide) (PEI) and SPEEK–polycarbonate (PC), and ternary blends of the SPEEK–PEI–PC, were investigated by differential scanning calorimetry. SPEEK was obtained by sulfonation of poly(ether ether ketone) using 95% sulfuric acid. From the thermal analysis of the SPEEK–PEI blends, single glass transition temperature (T_g) was observed at all the blend composition. For the SPEEK–PC blends, double T_gs were observed. From the results of thermal analysis, it is suggested that the SPEEK–PEI blends are miscible and the SPEEK–PC blends are immiscible. Polymer–polymer interaction parameter (χ₁₂) of the SPEEK–PEI blends was calculated from the modified Lu and Weiss equation, and found to range from −0.011 to −0.825 with the blend composition. For the SPEEK–PC blends, the χ₁₂ values were calculated from the modified Flory–Huggins equation, and found to range from 0.191 to 0.272 with the blend composition. For the SPEEK–PEI–PC ternary blends, phase separation regions that showed two T_gs were found to be consistent with the spinodal curves calculated from the χ₁₂ values of the three binary blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 2488–2494, 2000     

Micro‐ and ultrafiltration film membranes from poly(ether ether ketone) (PEEK)

Film membranes from the thermoplastic poly(ether ether ketone) (PEEK) have been extruded and tested for their microfiltration and ultrafiltration performance. High‐performance asymmetric membranes have been obtained by extruding polymer blends of PEEK, polysulphone, and a small molecule solvent mixture, and then by removing the polysulphone and solvent in a subsequent extraction step. The process for making ultrafiltration membranes differs from microfiltration membranes only in the relative blend components, and the temperature of the film pick‐up rolls. Processing parameters with important effects on the membrane performance have been identified. Microfiltration membranes are characterized by their pore‐size distributions and SEM, and ultrafiltration membranes by their rejection of bovine serum albumin, bubble point, and SEM. Composite membrane for nanofiltration utilizing the PEEK ultrafiltration membrane as a substrate performed similarly to a commercial membrane for the same purpose. This work details the best method for making PEEK film membranes published to date. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1146–1155, 1999     

Improved performance of carbon‐based supercapacitors with sulfonated poly(ether ether ketone)/poly(vinyl alcohol) composite membranes as separators

Supercapacitors have attracted much interest because of their high power density and long cycling life. However, the porous polypropylene membranes that are widely used as separators in supercapacitors are unfavorable for transporting ions and constructing the interfaces between electrolyte and electrodes due to their hydrophobic property. As a consequence, a crosslinked solid polymer electrolyte membrane and a semi‐interpenetrating polymer network (sIPN) were fabricated from sulfonated poly(ether ether ketone) (SPEEK) and poly(vinyl alcohol) (PVA), which can be used as hydrophilic separators. Their structures were examined using Fourier transform infrared spectroscopy. The electrochemical properties of assembled electrical double‐layer capacitors (EDLCs) were investigated using cyclic voltammetry, galvanostatic charging–discharging and impedance analysis. At a current density of 1 A g^?1, a single electrode in the EDLC with the sIPN shows a specific capacitance of 134 F g^?1. As a comparison, a single electrode in the EDLC with a SPEEK membrane demonstrates a specific capacitance of only 121 F g^?1. After 1000 charge–discharge cycles, the specific capacitance retentions of both EDLCs are nearly 100%. These results suggest that the sIPN based on SPEEK and PVA has great potential to serve as a separator in EDLCs. © 2018 Society of Chemical Industry     

Investigation on the crystallization behavior of poly(ether ether ketone)/poly(phenylene sulfide) blends

The morphology of nonisothermally crystallized poly(phenylene sulfide) (PPS) and its blend with poly (ether ether ketone) (PEEK) have been observed by polarized optical microscope (POM) equipped with a hot stage. The nonisothermal crystallization behavior of PPS and PEEK/PPS blend has also been investigated by differential scanning calorimetry (DSC). The maximum crystallization temperature for PEEK/PPS blend is about 15°C higher than that of neat PPS, and the crystallization rate, characterized by half crystallization time, of the PEEK/PPS blend is also higher than that of the neat PPS. These results indicate that the PEEK acts as an effective nucleation agent and greatly accelerates the crystallization rate of PPS. The Ozawa model was used to analyze the nonisothermal crystallization kinetics of PPS and its blends. The Avrami exponent values of neat PPS are higher than that of its blend, which shows that the presence of PEEK changed the nucleation type of PPS from homogeneous nucleation to heterogeneous nucleation. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008