Ethylene‐methyl acrylate‐glycidyl methacrylate toughened poly(lactic acid) nanocomposites

Poly (lactic acid) (PLA) was melt blended in a twin screw extruder using an ethylene‐methyl acrylate‐glycidyl methacrylate rubber as a toughener. PLA/rubber blends were immiscible as observed by scanning electron microscopy. Impact strength and ductility of PLA were improved by the addition of the rubber at the expense of strength and stiffness. An organo‐montmorillonite (OMMT) was used at 2 wt % to counteract the negative effect of the rubber on modulus, and balanced properties were observed at 10 wt % rubber content. X‐ray diffraction and transmission electron microscopy revealed the formation of intercalated/exfoliated structure in the ternary nanocomposites. Thermal behavior analysis indicated that the degree of crystallinity is slightly affected by the clay and the rubber. Both the clay and the rubber decreased the crystallization temperature of PLA and acted as nucleating agents for PLA. The viscosity of the mixtures as measured by melt flow index was highly influenced by the rubber and the OMMT. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation and some properties of stereocomplex‐type poly(lactic acid)/layered silicate nanocomposites

Stereocomplex‐type poly(lactic acid)‐ [PLA]‐ based blends were prepared by solution casting of equimolar PLLA/PDLA with different amounts of organo‐modified montmorillonite. The homocrystallization and stereocomplexation of PLAs were enhanced by annealing of the blends. The stereocomplexation of PLAs, intercalation of the polymer chains between the silicates layers, and morphological structure of the filled PLAs were analyzed by wide‐angle X‐ray diffraction and transmission electron microscope. Thermogravimetric analyses (TGA), differential scanning calorimetry (DSC), and tensile test were performed to study the thermal and mechanical properties of the blends. The homo‐ and stereocomplex crystallization of neat PLLA/PDLA were enhanced by annealing. The effect of annealing on the crystallization was emphasized by the addition of clay. With this structural change, thermal stabilities properties were also improved by the addition of clay. The silicate layers of the clay were slightly stacked but intercalated and distributed in the PLA‐matrix. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

An investigation of melt rheology and thermal stability of poly(lactic acid)/ poly(butylene succinate) nanocomposites

A systematic investigation of the rheological and thermal properties of nanocomposites prepared with poly(lactic acid) (PLA), poly(butylene succinate) (PBS), and organically modified layered silicate was carried out. PLA/PBS/Cloisite 30BX (organically modified MMT) clay nanocomposites were prepared by using simple melt extrusion process. Composition of PLA and PBS polymers were fixed at a ratio of 80 to 20 by wt % for all the nanocomposites. Rheological investigations showed that high clay (> 3 wt %) contents strongly improved the viscoelastic behavior of the nanocomposites. Percolation threshold region was attained between 3 and 5 wt % of clay loadings. With the addition of clay content for these nanocomposites, liquid‐like behavior of PLA/PBS blend gradually changed to solid‐like behavior as shown by dynamic rheology. Steady shear showed that shear viscosity for the nanocomposites decreased with increasing shear rates, exhibiting shear‐thinning non‐Newtonian behavior. At higher clay concentrations, pseudo‐plastic behavior was dominant, whereas pure blend showed almost Newtonian behavior. Thermogravimetric analysis revealed that both initial degradation temperature (at a 2% weight loss) and activation energy of thermal decomposition nanocomposite containing 3 wt % of C30BX were superior to those of other nanocomposites as well as to those of PLA/PBS blend. Nanocomposite having 1 wt % of C30BX did not achieve expected level of thermal stability due to the thermal instability of the surfactant present in the organoclay. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Poly(lactic acid)–layered silicate nanocomposites: The effects of modifier and compatibilizer on the morphology and mechanical properties

Poly(lactic acid) (PLA) based nanocomposites were prepared to investigate the effects of types of nanoclays. Five different organically modified nanoclays (Cloisites^®15A, 25A, and 30B, and Nanofils^®5 and 8) were used. Two rubbery compatibilizers, ethylene‐glycidyl methacrylate (E‐GMA) and ethylene‐butyl acrylate‐maleic anhydride, were used in the nanocomposites as compatibilizer‐impact modifier. The degree of clay dispersion, the chemical compatibility between the polymer matrix and the compatibilizers, and changes in the morphology and mechanical properties of the nanocomposites were investigated. The mechanical properties and the morphological studies showed that the interactions between the different compatibilizers and PLA resulted in different structures and properties; such that the dispersion of clay, droplet size of the compatibilizer, and tensile properties were distinctly dependent on the type of the compatibilizer. Compatibility between C25A, C30B, and E‐GMA resulted in the best level of dispersion, leading to the highest tensile modulus and toughness among the compositions studied. In the mentioned nanocomposites, a network structure was formed owing to the high reactivity of the epoxide group of GMA towards the PLA end groups resulting in high impact toughness. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42553.     

Compatibility,crystallinity and mechanical properties of poly(lactic acid)‐poly(ether‐block‐amide) based copper nanocomposites

Binary and ternary composites of poly(lactic acid) (PLA), poly(ether‐block‐amide) (PEBAX) and copper nanoparticles were prepared by melt blending in an internal mixer. Compatibility and molecular interactions between the three components of the nanocomposites were evaluated using scanning electron microscopy and Fourier transform infrared spectroscopy. It was found that the carbonyl groups of the PLA and copper nanoparticles interact. Also, PLA and PEBAX are compatible and develop molecular interactions between the C=O of PLA and the C=O and NH of PEBAX, forming dipole–dipole bonds and hydrogen bonds. The compatibility and molecular interaction between PLA and PEBAX are reduced by copper nanoparticles. The reduction of compatibility between PLA and PEBAX produced a lower storage modulus and lower strain at break in the ternary systems than in the blend PLA‐PEBAX. Copper nanoparticles enhanced the crystallinity of PLA. PLA responded more strongly to the nucleating effect of copper when PEBAX was added indicating a synergistic effect. The strain at break of PLA was enhanced by the addition of PEBAX but was severely reduced by the presence of nanoparticles. © 2020 Society of Chemical Industry     

Synergistic toughening and reinforcement of poly(lactic acid) with epoxy-terminated hyperbranched polymers

Poly(lactic acid) (PLA) is an eco-friendly and biodegradable material. However, its molecular chain was rigid and showed limited toughness. In this work, PLA was modified with epoxy-terminated hyperbranched polymer (EHBP) by melt blending to improve the toughness. The results showed that epoxy groups within EHBP reacted with carboxyl and hydroxyl groups of PLA, forming chemical micro-crosslinking. In addition, intermolecular hydrogen bonds were also formed between EHBP and PLA. The combined action of the above two aspects ultimately improved the toughness and strength of PLA. The mechanical property tests results showed that the mechanical properties of PLA improved best when 2.5 phr of EHBP was added. At this point, compared with neat PLA, the maximum tensile strength, impact strength, elongation at break, and flexural modulus of PLA/EHBP increased by 17.4%, 54.5%, 107.1%, and 25.8%, respectively, compared to those of neat PLA. It achieves the goal of simultaneously enhancing the toughness and strength of PLA and subsequently expands its potential application applications.     

Crystallization kinetics of poly (L‐lactic acid)/montmorillonite nanocomposites under isothermal crystallization condition

Poly(L ‐lactic acid)/o‐MMT nanocomposites, incorporating various amounts of organically modified montmorillonite (o‐MMT; 0–10 wt %), were prepared by solution intercalation. The montmorillonite (MMT) was organically modified with dilauryl dimethyl ammonium bromide (DDAB) by ion exchange. Transmission electron microscopy (TEM) and X‐ray diffraction (XRD) reveal that the o‐MMT was exfoliated in a poly(L ‐lactic acid), (PLLA) matrix. A series of the test specimens were prepared and subjected to isothermal crystallization at various temperatures (T₁–T₅). The DSC plots revealed that the PLLA/o‐MMT nanocomposites that were prepared under nonisothermal conditions exhibited an obvious crystallization peak and recrystallization, but neat PLLA exhibited neither. The PLLA/o‐MMT nanocomposites (2–10 wt %) yielded two endothermic peaks only under isothermal conditions at low temperature (T₁), and the intensity of Tm₂ (the higher melting point) was proportional to the o‐MMT content (at around 171°C). The melting point of the test samples increased with the isothermal crystallization temperature. In the Avrami equation, the constant of the crystallization rate (k) was inversely proportional to the isothermal crystallization temperature and increased with the o‐MMT content, especially at low temperature (T₁). The Avrami exponent (n) of the PLLA/o‐MMT nanocomposites (4–10 wt %) was 2.61–3.56 higher than that of neat PLLA, 2.10–2.56, revealing that crystallization occurred in three dimensions. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Relationship between the crystallization behavior of poly(ethylene glycol) and stereocomplex crystallization of poly(L‐lactic acid)/poly(D‐lactic acid)

Poly(l ‐lactic acid) (PLLA) is a good biomedical polymer material with wide applications. The addition of poly(ethylene glycol) (PEG) as a plasticizer and the formation of stereocomplex crystals (SCs) have been proved to be effective methods for improving the crystallization of PLLA, which will promote its heat resistance. In this work, the crystallization behavior of PEG and PLLA/poly(d ‐lactic acid) (PDLA) in PLLA/PDLA/PEG and PEG‐b‐PLLA/PEG‐b‐PDLA blends has been investigated using differential scanning calorimetry, polarized optical microscopy and X‐ray diffraction. Both SCs and homocrystals (HCs) were observed in blends with asymmetric mass ratio of PLLA/PDLA, while exclusively SCs were observed in blends with approximately equal mass ratio of PLLA/PDLA. The crystallization of PEG was only observed for the symmetric blends of PLLA_39k/PDLA_35k/PEG_2k, PLLA_39k/PDLA_35k/PEG_5k, PLLA_69k/PDLA_96k/PEG_5k and PEG‐b‐PLLA_31k/PEG‐b‐PDLA_27k, where the mass ratio of PLLA/PDLA was approximately 1/1. The results demonstrated that the formation of exclusively SCs would facilitate the crystallization of PEG, while the existence of both HCs and SCs could restrict the crystallization of PEG. The crystallization of PEG is related to the crystallinity of PLLA and PDLA, which will be promoted by the formation of SCs. © 2017 Society of Chemical Industry     

聚乳酸的合成及应用

综合分析了聚乳酸的合成方法和应用概况,重点阐述了间接开环聚合的机理,以及直接缩聚反应提高聚乳酸分子质量的最新进展概况。对聚乳酸的应用现状及应用前景进行了归纳分析,提出了聚乳酸研究的发展方向及重点应用领域。     

Biodegradable polymer blends of poly(lactic acid) and poly(ethylene glycol)

Poly(lactic acid) (PLA) and poly(ethylene glycol) (PEG) were melt-blended and extruded into films in the PLA/PEG ratios of 100/0, 90/10, 70/30, 50/50, and 30/70. It was concluded from the differential scanning calorimetry and dynamic mechanical analysis results that PLA/PEG blends range from miscible to partially miscible, depending on the concentration. Below 50% PEG content the PEG plasticized the PLA, yielding higher elongations and lower modulus values. Above 50% PEG content the blend morphology was driven by the increasing crystallinity of PEG, resulting in an increase in modulus and a corresponding decrease in elongation at break. The tensile strength was found to decrease in a linear fashion with increasing PEG content. Results obtained from enzymatic degradation show that the weight loss for all of the blends was significantly greater than that for the pure PLA. When the PEG content was 30% or lower, weight loss was found to be primarily due to enzymatic degradation of the PLA. Above 30% PEG content, the weight loss was found to be mainly due to the dissolution of PEG. During hydrolytic degradation, for PLA/PEG blends up to 30% PEG, weight loss occurs as a combination of degradation of PLA and dissolution of PEG. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 1495–1505, 1997     

茶粉/聚乳酸复合材料的增韧改性

为高值化利用茶产业剩余物资源,以茶粉（TD）为生物质填料,聚乳酸（PLA）为基体,以甘油（GL）、聚乙二醇400（PEG400）、环氧大豆油（ESO）和乙酰柠檬酸丁酯（ATBC）为增塑剂,制备了可降解TD/PLA增韧复合材料,并采用红外吸收光谱、热重分析、转矩流变仪、扫描电镜及力学性能测试等考察了增塑剂对TD/PLA复合材料结构与性能的影响。结果表明：4种增塑剂都可改善TD/PLA复合材料的加工流变性,GL的添加不利于复合材料韧性,PEG、ATBC及ESO的添加提高了复合材料韧性,其中ESO增韧效果最佳,其添加制备的复合材料断裂伸长率及缺口冲击强度分别提高了154.23%和65.53%,GL增韧效果最差,ATBC增韧后复合材料力学强度和模量最高。FTIR分析表明,ATBC和ESO可与PLA发生一定相互作用,使C-O键红外吸收峰位增大,其增韧后复合材料吸水率下降。ESO添加提高了TD/PLA复合材料的维卡软化点和热稳定性。SEM图片显示,TD/PLA/ESO复合材料断面粗糙,ESO分散较均匀,与PLA部分相容,而TD/PLA/GL复合材料断面出现严重相分离结构。该研究结果可为进一步探索聚乳酸基茶塑复合材料制备及应用提供试验数据和理论参考。     

超支化聚酰胺酯对聚乳酸增韧改性的研究

采用熔融共混的方法,用生物可降解的超支化聚酰胺酯(HBP)对聚乳酸(PLA)进行增韧改性,制备出具有良好韧性的PLA复合材料。对不同HBP含量的共混物的红外光谱、热性能和力学性能进行了测试和分析。红外光谱显示PLA和HBP间存在氢键作用。HBP的加入使PLA的结晶度从30.99%降低到18.58%。当HBP含量增加到10%时,PLA共混物的拉伸强度略有提高,且断裂伸长达到43.06%。结果表明:HBP的加入对PLA起到了很好的增韧作用。     

Gamma radiation induced property modification of poly(lactic acid)/hydroxyapatite bio‐nanocomposites

Poly(lactic acid)/hydroxyapatite (PLA/HAP) nanocomposite films with various compositions, 2 ? 70 parts HAP per 100 of the PLA polymer (pph), were made via the solution casting method. Transmission electron microscopy images of the PLA/HAP films exhibited spherical particles in the size range from nearly 10 nm to 100 nm dispersed within the polymeric matrix. Fourier transform infrared spectra of the nanocomposites revealed an interaction between PLA and HAP nanoparticles by carbonyl group peak shift. Incorporation of HAP nanoparticles in the PLA matrix stimulated crystal growth verified by differential scanning calorimetry. The films irradiated with γ‐rays at a dose of 30 kGy also showed an increase in crystallinity. The X‐ray diffraction patterns of the irradiated PLA exhibited two new peaks at around 16° and 19°, assigned to the α crystalline phase of PLA; these were absent in the unirradiated nanocomposites. Significant ductile behavior was observed in both irradiated and unirradiated PLA nanocomposites containing 2 and 10 pph of HAP. However, the irradiated nanocomposites had higher tensile strength. © 2013 Society of Chemical Industry     

Biodegradable poly(L‐lactic acid)/TiO2 nanocomposites: Thermal properties and degradation

Poly(L ‐lactic acid)‐titanium dioxide nanocomposites (with various loadings of TiO₂: 0.5, 1, 2, 5, and 10 wt %) were produced by solution casting method. The influence of TiO₂ on thermal properties and crystallinity of PLA was investigated by DSC and FTIR spectroscopy. The TiO₂ nano filler has no significant influence on the characteristic temperatures (T_g, T_c, and T_m), but has high impact on the crystallinity of these systems. The degree of crystallinity X_c significantly increases for PLA nanocomposites loaded with up to 5 wt % of TiO₂, while for 10 wt % load of TiO₂ it drops below X_c of the pure resin. The degradation of the prepared composites was evaluated hydrolytically in 1N NaOH, enzymatically in α‐amylase solutions, and under UV irradiation. The catalytic effect of TiO₂ nano particles on the degradation processes under UV light exposure (λ = 365 nm) and hydrolytic degradation was confirmed with the increase of the filler content. The opposite effect was identified in enzymatic degradation experiments. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

聚酰胺弹性体增韧聚乳酸改性研究

选用聚酰胺弹性体(聚酰胺和聚氧乙烯的共聚物,PAE)与聚乳酸(PLA)熔融共混进行增韧改性。结果表明,当PAE弹性体含量在20%～30%(质量分数,下同)之间时,共混体系发生脆韧转变,最大冲击强度达到67.6J/m,但拉伸强度和模量大幅度下降;PAE弹性体含量为5%～10%时共混体系的拉伸强度保持率最高,而且断裂伸长率提高近40倍,综合性能较好;虽然扫描电子显微镜照片显示共混体系为两相分离,但是差示扫描量热分析数据均表明,随着PAE弹性体含量的增加,共混体系的玻璃化转变温度和熔点发生相应变化,证明该共混体系为半溶混性,即两相间存在一定的相互作用;热失重分析数据显示,PAE弹性体在一定程度上提高了PLA的热降解温度。     

Preparation and characterization of poly(styrene‐co‐butadiene) and polybutadiene rubber/clay nanocomposites

Poly(styrene‐co‐butadiene) rubber (SBR) and polybutadiene rubber (BR)/clay nanocomposites have been prepared. The effects of the incorporation of inorganically and organically modified clays on the vulcanization reactions of SBR and BR were analysed by rheometry and differential scanning calorimetry. A reduction in scorch time (t_s1) and optimum time (t₉₅) was observed for both the rubbers when organoclay was added and this was attributed to the amine groups of the organic modifier. However, t_s1 and t₉₅ were further increased as the clay content was increased. A reduction in torque value was obtained for the organoclay nanocomposites, indicating a lower number of crosslinks formed. The organoclays favoured the vulcanization process although the vulcanizing effect was reduced with increasing clay content. The tensile strength and elongation of SBR were improved significantly with organoclay. The improvement of the tensile properties of BR with organoclay was less noticeable than inorganic‐modified clay. Nevertheless, these mechanical properties were enhanced with addition of clay. The mechanical properties of the nanocomposites were dependent on filler size and dispersion, and also compatibility between fillers and the rubber matrix. Copyright © 2004 Society of Chemical Industry     

聚（乳酸⁃乙醇酸）薄膜制备及其性能研究

以左旋乳酸（L?LA）和乙醇酸（GA）为原料,利用一步法熔融共聚合成聚（乳酸?乙醇酸）（PLLGA）共聚物,通过差示扫描量热仪（DSC）对共聚物薄膜的结晶性能进行了表征,并利用Avrami方程对其进行了等温结晶动力学研究,通过万能拉伸试验机和压差法气体透过仪对共聚物薄膜的力学性能和气体阻隔性能进行测试。结果表明,PLLGA共聚物薄膜中GA的引入对材料结晶性能有较大影响,在GA含量为4 %（摩尔分数,下同）的PLLGA中,GA表现为成核剂作用,共聚物结晶比纯聚左旋乳酸（PLLA）薄膜快,半结晶时间减少;而在GA含量为8 %的PLLGA中,GA则表现出限制分子链运动的作用,破坏共聚物分子间的规整度,导致材料结晶性能大幅度降低,处于非晶态;随着GA含量的增加,PLLGA薄膜的拉伸强度和弹性模量逐步下降,而断裂伸长率大幅度增加,GA含量为8 %的PLLGA的断裂伸长率达到了130.1 %,是纯PLLA薄膜的21.3倍;同时,PLLGA薄膜的气体阻隔性显著增加,5 ℃时,相比于纯PLLA薄膜,GA含量为8 %的PLLGA薄膜的O₂、CO₂、N₂透过量分别降低了47 %、41 %和39 %。     

可生物降解聚乳酸类胶粘剂的研究进展

对可生物降解的聚乳酸类胶粘剂的种类、应用及最新的研究进展等几个方面进行了综述。特别介 绍了工业用聚乳酸类胶粘剂和医学用聚乳酸类胶粘剂的研究进展。     

High performance nanocomposites of polyurethane elastomer and organically modified layered silicate

High performance nanocomposites comprising a polyurethane elastomer (PUE) and an organically modified layered silicate are prepared. These nanocomposites are based on poly(propylene glycol), 4,4′‐methylene bis(cyclohexyl isocyanate), 1,4‐butandiol, and organoclay. The tensile strength and strain at break for these novel PUE nanocomposites increases more than 150%, but the hardness remains unchanged. The fatigue properties are significantly improved. With 3 wt % organoclay, the fatigue properties are improved the most, which is important for the PU industry. The effects of the isocyanate index on the mechanical properties of the PUE nanocomposites are investigated. It is found that an isoyanate index of 1.10 results in the best improvement in stress and elongation at break. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3239–3243, 2003     

Effect of modified layered silicates on the confined crystalline morphology and thermomechanical properties of poly(ethylene oxide) nanocomposites

In this work, poly(ethylene oxide) (PEO)/organoclay nanocomposites with three different types of nanoclays (Cloisite 30B, Somasif JAD400, and Somasif JAD230) were prepared by melt mixing with a laboratory kneader followed by compression molding. The nanocomposites were characterized by atomic force microscopy and scanning electron microscopy. Their crystallization behavior on a hot stage was investigated with polarized optical microscopy. The size and regularity of the spherulites of the PEO matrix were altered significantly by the incorporation of Cloisite 30B, but there was not as much variation with the other two clays. The dynamic viscoelastic behavior of the PEO/organoclay nanocomposites was assessed with a strain‐controlled parallel‐plate rheometer. The effects of clay modification on the thermomechanical and rheological properties were addressed. The reinforcing effect of the organoclay was determined with dynamic mechanical analysis and tensile testing. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010