液体异戊二烯橡胶的合成及结构表征

采用锂系阴离子聚合工艺合成4种液体异戊二烯橡胶（LIR）,用红外光谱及核磁共振对合成样品的结构进行了剖析并与国外样品进行了对比,结果表明合成LIR的结构与国外同类样品相当。     

Effect of inert plasticizers on mechanical,thermal, and sensitivity properties of polyurethane‐based plastic bonded explosives

Mechanical, thermal, and sensitivity properties of plastic bonded explosives (PBX) depend on the type of ingredients in their formulation. Aim of the work is to develop aluminized cast PBX formulations and process conditions by using alternative inert plasticizers to have similar or better properties than PBXN‐109 without compromising sensitivity properties. Although very small portion of total production of plasticizers is used for solid rocket propellant and explosive formulations, they play very significant role in that area. Both inert and energetic plasticizers have involved propellant and explosive formulations to improve process parameters, mechanical properties, and even insensitivity properties of them. Isodecyl pelargonate and dioctyl adipate are the most preferred inert plasticizers in polyurethane based thermoset propellant and explosive formulations. In addition to them, diisononyl adipate and diisononyl phthalate were used and screened as inert plasticizer candidates for aluminized cast PBX formulations. Mechanical, thermal, and sensitivity properties of PBX formulations were studied and compared in detail. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40907.     

Influence of complexing treatment and epoxy resin coating on the properties of aramid fiber reinforced natural rubber

In this work, natural rubber/aramid fiber (NR/AF) composites were prepared with master batch method. AF was modified by using epoxy resin (EP) and accelerator 2‐ethyl‐4‐methylimidazole (2E4MZ) through surface coating on the basis of the complexing treatment with CaCl₂ solution. Hydroxyl‐terminated liquid isoprene rubber (LIR) was regarded as a compatibilizer between EP and NR. It is found that the crystallinity on AF surface is decreased by complexing reaction with CaCl₂ solution. Swelling and mechanical properties of the vulcanized composites, such as swelling degree, tensile and tear strength, tensile modulus at 300% elongation, are measured, and the tensile fracture morphology and dynamic mechanical analysis of the composites are investigated. The results show that the mechanical properties of composites with modified fibers are improved obviously and interfacial adhesion between matrix and the fiber is enhanced, especially for the AF coated with EP and imidazole. The best comprehensive mechanical properties of the composites are obtained with using CaCl₂‐EP/2E4MZ system when the ratio of m(EP)/m(AF) is 3%. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42122.     

Influence of ionic liquid on the polymer–filler coupling and mechanical properties of nano‐silica filled elastomer

The natural rubber (NR) nanocomposites were fabricated by filling ionic liquid (1‐allyl‐3‐methyl‐imidazolium chloride, AMI) modified nano‐silica (nSiO₂) in NR matrix through mechanical mixing and followed by a cure process. Based on the measurements of differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), solid state nuclear magnetic resonance spectroscopy, and Raman spectroscopy, it was proved that AMI could interact with nSiO₂ through hydrogen bonds. With the increase of AMI content, the curing rate of nSiO₂/NR increased. The results of bound rubber and dynamic mechanical properties showed that polymer–filler interaction increased with the modification of nSiO₂. Morphology studies revealed that modification of nSiO₂ resulted in a homogenous dispersion of nSiO₂ in NR matrix. AMI modified nSiO₂ could greatly enhance the tensile strength and tear strength of nSiO₂/NR nanocomposites. Compared to unmodified nSiO₂/NR nanocomposite, the tensile strength of AMI modified nSiO₂/NR nanocomposite increased by 102%. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44478.     

Intumescent flame retardant polyurethane/starch composites: Thermal,mechanical, and rheological properties

Intumescent flame retardant polyurethane/starch (IFRPU/starch) composites were prepared by means of melt blending. Microencapsulated ammonium polyphosphate (MCAPP) was added to improve its compatibility with matrix, retardation of reaction between acid and carbon source, and its water resistancy. Fourier transform infrared spectroscopy (FTIR) confirmed the presence of hydrogen bonding and entangled network between IFR system and PU matrix. Further, scanning electron microscopy (SEM) illustrated homogeneity of starch in matrix. By addition of 10 wt % of starch and 20 wt % of IFR, limiting oxygen index (LOI) increased from 22.0 to 40.0 and UL94 V0 rating was achieved. Differential scanning calorimetry (DSC) detected three endothermic transitions and one glass transition (T_g). The temperature of transition III and T_g increased with starch due to crosslinking between PU and starch. The improved thermal stability in the presence of starch was confirmed by thermogravimetric analysis (TGA). Beside the fact that starch was used as a carbonization agent to improve flame retardancy, it also effectively led to enhanced mechanical and viscoelastic properties. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41158.     

An innovative material based on natural rubber and leather tannery waste to be applied as antistatic flooring

In recent decades, the production chain of beef and bovine leather has grown significantly because of an increase in the world's population and improved access to consumption. However, the generation of waste derived from this sector has grown simultaneously, and consequently, improved ways of adding value, reusing, and disposing these waste materials are being sought. In this article, we present a new and innovative composite material based on vulcanized natural rubber (NR), carbon black (CB), and leather waste (NR/CB/leather). The NR/CB/leather composites were prepared by thermal compression with 60 phr of CB and 60 or 80 phr of leather waste. In accordance with Brazilian sanitary laws, we exposed these composites for 24 h to bleach (B) and a disinfectant with the aim of simulating a true everyday cleaning use. The deconvolution of the impedance semicircles was carried out, and two relaxation phenomena around linear relaxation frequencies of about 10⁵ and 10⁶ Hz were found and associated mainly with charge carriers from CB and leather waste. With the addition of leather, the electrical conductivity of the composites increased two orders of magnitude from 5.70 × 10^?6 for the NR/CB to 7.97 × 10^?4 S/cm for NR/CB/leather‐60 phr B. These results point to the possibility of using these composites as an antistatic flooring once they exhibit acceptable values of electrical conductivity and once they withstand, from the structural, morphological, and electrical point of view, exposure to sanitizing agents. Furthermore, the production of these composites will add value to and enable an environmentally acceptable disposal of leather waste. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41297.     

Cotton fibers reinforcement of HNBR: Control of fiber alignment and its influence on properties of HNBR vulcanizates

This article focuses on the reinforcement of hydrogenated acrylonitrile butadiene rubber (HNBR) by cotton fiber as natural reinforcing filler. The effect of fiber alignment on the properties of HNBR compounds and vulcanizates is investigated. Properties of interest include rheological behavior, cure, tensile, abrasion, and dynamic mechanical properties which are correlated to the magnitudes of state‐of‐mix, bound rubber content, crosslink density and fiber alignment. Results obtained reveal that mechanical properties of rubber composites are improved dramatically by the addition of cotton fiber due to the enhanced hydrodynamic effect in association with crosslink density. Furthermore, the degree of fiber alignment is found to depend strongly on shear strain. The results demonstrate the importance of fiber alignment controlled efficiently by shear strain. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41090.     

Influence of matrix viscosity on the dynamic mechanical performance of magnetorheological elastomers

Anisotropic magnetorheological elastomers (MREs) with different natural rubber matrix viscosities and industrial waste nickel zinc ferrite were prepared in order to assess the dynamic and mechanical performance of the materials. The curing characteristics of the anisotropic MREs were determined using a moving disk rheometer (MDR 2000). The loss tangent (tan δ) was measured through a parallel-plate rheometer over a frequency range of 1─100 Hz (Hz) and a strain amplitude range of 0.1─6%. It was found that tan δ increased with increasing matrix viscosity over the range of frequency and strain amplitude explored. Furthermore, as the matrix viscosity increased, the height of the tan δ peak also increased and the glass transition temperature (T_g) valued shifted to a higher temperature. It was also found that tensile strength and elongation at break increased with increasing matrix viscosity. The SEM micrographs revealed that the columnar structures became longer and thicker with a decrease in matrix viscosity. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48492.     

Effect of liquid isoprene rubber on dynamic mechanical properties of emulsionpolymerized styrene/butadiene rubber vulcanizates

The effect of liquid isoprene rubber (LIR) on the dynamic mechanical properties of emulsion‐polymerized styrene/butadiene rubber (ESBR) vulcanizates was investigated by temperature sweep using dynamic mechanical analysis. The introduction of LIR led to ESBR vulcanizates having higher loss factor (tan δ) in the temperature range ? 30 to 0 °C, and lower tan δ in the range 60 to 80 °C. A small amount of LIR‐403 (LIR with carboxyl groups) led to a significant change in tan δ: the addition of LIR‐403 (3 phr) led to a 7.5% increase in tan δ from ? 30 to 0 °C, and a 24.9% decrease in tan δ from 60 to 80 °C. It was found that the introduction of LIR increased the bound rubber content in the ESBR compound. Equilibrium swelling experiments showed that the crosslink density of the vulcanizates increased after the introduction of LIR‐403 or LIR‐50 (general purpose LIR). The change in tan δ from 60 to 80 °C was related to polymer–filler interactions. The characteristic constant of filler–ESBR matrix interaction (m) was calculated. At a given filler volume fraction, the increase in m in the presence of LIR could be well related to the decrease in tan δ from 60 to 80 °C. The influence of LIR on filler network in the ESBR compound was also investigated by strain and temperature sweeps using a rubber processing analyzer. Copyright © 2011 Society of Chemical Industry     

Influence of modification process parameters on the properties of crumb rubber/EVA modified asphalt

Crumb rubber (CR) and ethylene vinyl acetate copolymer (EVA) were adopted as asphalt modifiers. Routine tests, softening point, penetration, and ductility were used to evaluate the basic properties of crumb rubber and ethylene vinyl acetate copolymers (CR/EVA) modified asphalt. The segregation experiment measured the storage stability. Modern test methods such as fluorescence microscopic photography technology was used to study stability of polymer modified asphalt. Infrared spectrum experiment was used to analyze the composition differences of the upper part and lower part of CR/EVA modified asphalt. Matlab software was employed to fit out the formulae of ductility, penetration, and softening point difference of modified asphalt and shearing temperature, shearing time and shearing rate separately. Compared with base asphalt, the properties of CR/EVA modified asphalt have been greatly improved. The formulae which were fitted out by Matlab software showed that the shearing time was the foremost factor affecting the properties of CR/EVA modified asphalt, followed by shearing temperature, and the last was shearing rate. The conclusions which were fitted by orthogonal experiment were basically consistent with the results of formulae which were fitted out by Matlab software. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43598.     

Influence of PP fiber and SBR latex on the mechanical properties of crumb rubber mortar

This article presents a new kind of rubber mortar modified by polypropylene fiber (PP fiber) and styrene‐butadiene rubber latex (SBR latex). The mechanical properties of this crumb rubber mortar were investigated in the research, including the compressive strength, flexural strength, flexural toughness, and flexural elasticity modulus. The test results showed that the flexural toughness index of the rubber mortar was seen to enhance by about 50–100% with the addition of PP fiber and SBR polymer latex. Due to the addition of PP fiber and SBR latex, the flexural elastic modulus of rubber mortar could further reduce by 4–27%. The three‐phase composite dispersion model of this rubber mortar was put forward. Furthermore, it was observed from scanning electron micrograph that the interfacial transition zone between the rubber particles and cement paste was enhanced by the SBR latex, and the interleaving of polymer films and rubber particles strengthen the flexibility and toughness of the mortar. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40591.     

Influence of processing on morphology in short aramid fiber reinforced elastomer compounds

The rubber industry is nowadays facing the general increase of raw materials as the customers are confronted with rising prices for energy. Therefore there is a need for higher durability of elastomer applications. Short fiber reinforced elastomers can contribute to the improvement of dynamic and wear properties. To determine structure–property relationships in short fiber reinforced elastomer compounds it is of crucial interest to know the contributions of fiber aspect ratio, volume content, orientation and fiber–elastomer interaction. Therefore the influence of different processing conditions and fiber contents on the resulting morphology and macroscopic properties was investigated in this article by the help of fluorescence and confocal laser microscopy using a transparent ethylene‐propylene‐diene rubber (EPDM) matrix. It was found that the processing induced fiber breakage was the key factor in determining the composite morphology and subsequent physical properties. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1682–1690, 2013     

液体异戊橡胶对顺丁橡胶/天然橡胶共混胶性能的影响

考察了分别用自制的液体异戊橡胶和液体异戊橡胶LIR-50等量取代顺丁橡胶/天然橡胶共混胶中的天然橡胶部分时对共混胶性能的影响。结果表明,液体异戊橡胶的加入对于共混胶料的抗湿滑性能有所改善,但同时也增大滚动阻力。随着液体异戊橡胶用量(5~15份)的增加,共混硫化胶的拉伸强度、撕裂强度和扯断伸长率稍有下降,磨耗量和生热有所增大。2种液体异戊橡胶的使用效果相当。     

Thermal and mechanical properties of liquid silicone rubber composites filled with functionalized graphene oxide

To improve the thermal and mechanical properties of liquid silicone rubber (LSR) for application, the graphene oxide (GO) was proposed to reinforce the LSR. The GO was functionalized with triethoxyvinylsilane (TEVS) by dehydration reaction to improve the dispersion and compatibility in the matrix. The structure of the functionalized graphene oxide (TEVS‐GO) was evaluated by Thermogravimetric analysis (TGA), Fourier transform infrared (FTIR) spectra, X‐ray diffraction (XRD), and energy dispersive X‐ray spectroscopy (EDX). It was found that the TEVS was successfully grafted on the surface of GO. The TEVS‐GO/LSR composites were prepared via in situ polymerization. The structure of the composites was verified by FTIR, XRD, and scanning electron microscopy (SEM). The thermal properties of the composites were characterized by TGA and thermal conductivity. The results showed that the 10% weight loss temperature (T₁₀) increased 16.0°C with only 0.3 wt % addition of TEVS‐GO and the thermal conductivity possessed a two‐fold increase, compared to the pure LSR. Furthermore, the mechanical properties were studied and results revealed that the TEVS‐GO/LSR composites with 0.3 wt % TEVS‐GO displayed a 2.3‐fold increase in tensile strength, a 2.79‐fold enhancement in tear strength, and a 1.97‐fold reinforcement in shear strength compared with the neat LSR. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42582.     

Influence of morphology on rheological and mechanical properties of SEBS-toughened,glass-bead-filled isotactic polypropene

The influence of morphology of glass-bead-filled isotactic polypropene containing 0–20 vol% thermoplastic elastomers (TPE) on mechanical and rheological properties was investigated. Polystyrene-block-poly(ethene-co-but-1-ene)-block-polystyrene(SEBS) and the corresponding block copolymer grafted with maleic anhydrid (SEBS-g-MA) were used as thermoplastic elastomers, realizing, in the first case, a three-phase morphology with separately dispersed glass beads and SEBS particles. In the second case, SEBS-g-MA forms an elastomeric interlayer between glass beads and polypropene matrix, comprising core–shell particles. Young's modulus and tensile yield stress of the hybrid composites decrease with an increase in TPE volume fraction due to low stiffness and strength of TPE. In comparison with the three-phase morphology of hybrid composites with SEBS, SEBS-g-MA interlayers effect a reduced stiffness of the hybrid composites but improve interfacial adhesion and, thus, tensile yield stress. Rheological storage and loss moduli increase with an increase in glass bead and TPE volume fraction. Due to improved interfacial adhesion, melt elasticity and viscosity are enhanced by the SEBS-g-MA interlayer when compared with separately dispersed SEBS. Consequently, the reduced stiffening effect of the glass beads due to SEBS-g-MA interlayer decreases mechanical elasticity, whereas improved interfacial adhesion, also promoted by the SEBS-g-MA interlayer, enhances tensile yield stress and melt elasticity. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 2499–2506, 1998     

Enhancement of rheological and mechanical properties of bitumen using styrene acrylonitrile copolymer

In this research, styrene acrylonitrile copolymer as a novel additive is used to modify rheological, mechanical and thermal properties of the base bitumen 70 penetration grade. Styrene acrylonitrile copolymer combines the rigidity of polystyrene with the hardness and thermal resistance of polyacrylonitrile to enhance viscoelastic property of the bitumen. To investigate the performance of the proposed mixture, shear complex module, phase angle, penetration, softening point, and reversibility of prepared samples are measured at different additive content and compared with the base bitumen. The results show that softening point of the base and modified samples are 49–86°C, respectively. The rheological properties of the base bitumen and modified samples are measured by a dynamic shear rheometer (DSR). The phase angle as elasticity measure decreases from 55° to 35° in the modified bitumen compared to the base bitumen. Generally, the experimental results showed that styrene acrylonitrile copolymer makes bitumen to be more stable at high temperatures and more flexible at low temperatures. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41875.     

Compressive mechanical properties of HTPB propellant at low,intermediate, and high strain rates

Low, intermediate, and high strain rate compression testing (1.7 × 10^?4 to 2500 s^?1) of the hydroxyl‐terminated polybutadiene (HTPB) propellant at room temperature, were performed using a universal testing machine, a hydraulic testing machine, and a split Hopkinson pressure bar (SHPB), respectively. Results show that the stress linearly increases with strain at each condition; the increasing trend of stress at a given strain with the logarithm of strain rate changes from a linear to an exponential form at 1 s^?1. By combining these characteristics, we propose a rate‐dependent constitutive model which is a linearly elastic component as a base model, then multiplied by a rate‐dependent component. Comparison of model with experimental data shows that it can characterize the compressive mechanical properties of HTPB propellant at strain rates from 1.7 × 10^?4 to 2500 s^?1. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43512.     

Effect of physical and chemical crosslinking structure on fatigue behavior of styrene butadiene elastomer

The fatigue behavior of two styrene butadiene rubbers, thermoplastic elastomer (SBS) with physical crosslinking structure and vulcanized styrene butadiene rubber (SBR) with chemical crosslinking structure, was investigated. The fatigue lives of SBS and SBR were greatly affected by the fatigue frequency, amplitude, and temperature. The fatigue lives of both SBS and SBR decreased with the increasing fatigue frequency and amplitude. However, the effect of fatigue temperature on the fatigue life of SBS was different from that of SBR. With the increasing fatigue temperature, the fatigue life of SBS first decreased and then increased, however, the fatigue life of SBR showed continuous decreasing trend. The tensile strength of SBS first increased and then decreased with the increase of fatigue time, but the tensile strength of SBR was not significantly influenced by the fatigue time. The fatigue amplitude had greater effect on the tensile strength of SBS than that of SBR. The permanent deformation of both SBS and SBR increased with temperature; however, the parameter for the former rubber was higher than that of the latter. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40917.     

Simultaneous toughening of PPO/HIPS/Glass fiber reinforced composites with thermoplastic rubbers

Simultaneously reinforced and toughened PPO/HIPS/SEBS/glass fiber (GF) 60/40/5/30 composites were successfully prepared with GF as reinforcing agent and SEBS as toughener. The formulation of PPO/HIPS/SEBS/GF quaternary composites was stepwise optimized by evaluating the effect of GF and SEBS on the processing, mechanical and thermal properties of the composites. The synergistic effects of GF reinforcement and elastomer toughening are attributed to high performance PPO/HIPS/SEBS/GF composites. Among the four elastomers studied, SEBS exhibited as effective toughener for PPO/HIPS matrix and the resulted PPO/HIPS/SEBS/GF composites presented a good combination of mechanical and thermal properties. The optimized PPO/HIPS/SEBS/GF 60/40/5/30 quaternary composites displayed a tensile strength of 123.6 MPa, a bending strength of 149.7 MPa, an unnotched impact strength of 46.6 KJ/m² and a heat distortion temperature of 148.9°C. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40299.     

Nanoclay distribution and its influence on the mechanical properties of rubber blends

The distribution of modified and unmodified nanoclays inside the rubber phases of immiscible rubber–rubber blends composed of nonpolar–polar natural rubber (NR)/epoxidized natural rubber (ENR) and nonpolar–nonpolar NR/polybutadiene rubber (BR) was investigated for the first time. The distribution of clays at various loadings in the blends was calculated from the viscoelastic properties of the blends. For example, in the 50 : 50 NR/ENR blend, 42% Cloisite 30B migrated to the NR phase, and 58% went to the ENR phase. However, in the same blend, only 7% Cloisite Na⁺ was found in the NR phase, and 93% was found in the ENR phase. Again, in the 50 : 50 NR/BR blends, the NR phase contained 85% Cloisite 30B, whereas 55% Cloisite Na⁺ migrated to the NR phase. All these observations were explained with the help of viscosity, X‐ray diffraction, and morphology analyses. The effect of the distribution of the clay on the mechanical properties was also discussed. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010