Characterization of transition joints of commercially pure titanium to 304 stainless steel

Solid-state direct bonding between commercially pure titanium and type 304 austenitic stainless steel has been carried out in the temperature range of 850–950 °C, under a uniaxial pressure of 3 MPa for 1 h. The diffusion bonds have been evaluated using light microscopy, electron probe microanalysis (EPMA), X-ray diffraction (XRD) technique and tensile testing. Light microscopy shows that different intermediate layers are formed in the reaction zone, and the width of these layers increases with an increase in bonding temperature. EPMA revealed that, at any particular bonding temperature, Ti traverses a minimum distance in the 304 stainless steel side, whereas Fe, Cr and Ni travel comparatively larger distances in the Ti side. This microanalysis also indicated different step formations in the concentration profile of Ti, Fe and Cr over different composition ranges in the diffusion zone indicating formation of intermetallic phases that were detected by XRD. Brittle intermetallic phases lower the strength and ductility of the diffusion bonded couples significantly. Best room temperature tensile strength, 217 MPa, has been obtained at 850 °C processing temperature due to minimal deleterious effects.     

Evaluation of the microstructure and mechanical properties of diffusion bonded joints of titanium to stainless steel with a pure silver interlayer

Solid-state diffusion bonding of commercially pure titanium to 304 stainless steel using an Ag interlayer was carried out at 825–875 °C under a uniaxial pressure of 8 MPa for 20 min in vacuum. The microstructural observations revealed that the resultant joints were composed of the remnant Ag interlayer, TiAg intermetallic phase and Ti–Ag solid solution. An optimized bonding strength of up to 414 MPa was achieved. Fracture took place through the remnant Ag interlayer during tensile tests and the interfacial TiAg phase exhibited no detrimental effect on the bonding strength. Extensive dimples were observed on the fracture surfaces, indicating that the joints were ductile in nature.     

Diffusion bonding between commercially pure titanium and micro-duplex stainless steel

Diffusion-bonded joints between commercially pure titanium and micro-duplex stainless steel were prepared in the temperature range of 800–950 °C for 1.5 h under 3 MPa uniaxial load in vacuum. The diffusion bonds were characterized using light and scanning electron microscopy. The composition of the reaction products were determined by energy dispersive spectroscopy. Up to 850 °C, -Fe + λ and λ + FeTi phase mixtures were formed at diffusion interface; however -Fe + λ, λ + FeTi and FeTi + β-Ti phases mixtures were formed at 900 °C and above. The presence of these intermetallics was confirmed by X-ray diffraction technique. The maximum tensile strength of 96% of Ti and shear strength of 81% of Ti along with 6.9% ductility were obtained for the diffusion couple processed at 850 °C due to the finer width of intermetallic phases. With a rise in the joining temperature the bond strength drops owing to an increase in the width of reaction products.     

Vacuum hot roll bonding of titanium alloy and stainless steel using nickel interlayer

Abstract

Vacuum hot roll bonding of titanium alloy and stainless steel using a nickel interlayer was investigated. No obvious reaction or diffusion layer occurs at the interface between stainless steel and nickel. The interface between titanium alloy and nickel consists of an occludent layer and diffusion layers, and there are the intermetallic compounds (TiNi₃, TiNi, Ti₂Ni and their mixtures) in the layers. The total thickness of intermetallic layers at the interface between titanium alloy and nickel increases with the bonding temperature, and the tensile strength of roll bonded joints decreases with the bonding temperature. The maximum tensile strength of 440·1 MPa was obtained at the bonding temperature of 760°C, the reduction of 20% and the rolling speed of 38 mm s^–1.     

Diffusion bonding of titanium alloy to micro-duplex stainless steel using a nickel alloy interlayer: Interface microstructure and strength properties

In the present study, diffusion bonding of titanium alloy and micro-duplex stainless steel with a nickel alloy interlayer was carried out in the temperature range of 800–950 °C for 45 min under the compressive stress of 4 MPa in a vacuum. The bond interfaces were characterised by scanning electron microscopy, electron probe microanalyzer and X-ray diffraction analysis. The layer wise Ni₃Ti, NiTi and NiTi₂ intermetallics were observed at the nickel alloy/titanium alloy interface and irregular shaped particles of Fe₂₂Mo₂₀Ni₄₅Ti₁₃ was observed in the Ni₃Ti intermetallic layer. At 950 °C processing temperature, black island of β-Ti phase has been observed in the NiTi₂ intermetallics. However, the stainless steel/nickel alloy interface indicates the free of intermetallics phase. Fracture surface observed that, failure takes place through the NiTi₂ phase at the NiA–TiA interface when bonding was processed up to 900 °C, however, failure takes place through NiTi₂ and β-Ti phase mixture for the diffusion joints processed at 950 °C. Joint strength was evaluated and maximum tensile strength of ∼560 MPa and shear strength of ∼415 MPa along with ∼8.3% ductility were obtained for the diffusion couple processed at 900 °C for 45 min.     

Diffusion bonding of 410 stainless steel to copper using a nickel interlayer

In the present work, plates of stainless steel (grade 410) were joined to copper ones through a diffusion bonding process using a nickel interlayer at a temperature range of 800–950 °C. The bonding was performed through pressing the specimens under a 12-MPa compression load and a vacuum of 10^? 4 torr for 60 min. The results indicated the formation of distinct diffusion zones at both Cu/Ni and Ni/SS interfaces during the diffusion bonding process. The thickness of the reaction layer in both interfaces was increased by raising the processing temperature. The phase constitutions and their related microstructure at the Cu/Ni and Ni/SS diffusion bonding interfaces were studied using optical microscopy, scanning electron microscopy, X-ray diffraction and elemental analyses through energy dispersive spectrometry. The resulted penetration profiles were examined using a calibrated electron probe micro-analyzer. The diffusion transition regions near the Cu/Ni and Ni/SS interfaces consist of a complete solid solution zone and of various phases based on (Fe, Ni), (Fe, Cr, Ni) and (Fe, Cr) chemical systems, respectively. The diffusion-bonded joint processed at 900 °C showed the maximum shear strength of about 145 MPa. The maximum hardness was obtained at the SS–Ni interface with a value of about 432 HV.     

Influence of interface microstructure on the mechanical properties of titanium/17-4 PH stainless steel solid state diffusion bonded joints

In the present study, titanium was diffusion bonded to a type 17-4 precipitation hardening stainless steel in vacuum at different temperatures and times. Bonded samples were characterized using light microscopy, scanning electron microscopy (SEM) and X-ray diffraction technique (XRD). The inter-diffusion of the chemical species across the diffusion interface was evaluated by electron probe microanalysis (EPMA). Up to 850 °C for 60 min, FeTi phase was formed at the diffusion interface; however, α-Fe + λ, χ, Fe₂Ti and FeTi phases and their phase mixtures were formed above 850 °C for 60 min and at 900 °C for all bonding times. The maximum tensile strength of ∼342.4 MPa and shear strength of ∼260.3 MPa along with 12.8% elongation were obtained for the diffusion couple processed at 950 °C. The thicknesses of different reaction products at the bond interface play an important role in determining the mechanical properties of the joints. The residual stress of the bonded joints increases with the increases in bonding temperatures and times.     

Failure of weld joints between carbon steel pipe and 304 stainless steel elbows

A number of weld joints between carbon steel (CS) pipe and type 304 stainless steel (SS) elbows constituting a gas piping system of a petrochemical unit developed cracks after a relatively short period of usage, resulting in leakage. The gas flowing through the pipe, was hydrogen rich at a temperature of 45 °C and a pressure of 16 kg/cm². Light optical metallography and scanning electron microscopy, combined with energy dispersive X-ray spectroscopy, inductively coupled plasma and microhardness testing were used to determine the most probable cause of failure. Analysis showed that the cracks originated at the interface between the CS pipe and the SS root weld. A narrow band between the CS pipe and SS weld exhibited a hardness of Rockwell C 60 suggesting the formation of martensite due to C segregation at welding temperature and subsequent quenching during cooling. The ferritic region of CS adjacent to the weld was decarburized and was devoid of pearlite; corroborating C diffusion. The weld region was diluted comprising mainly of Fe with small amounts of Cr and Ni. Cracking is thought to have initiated at the hardened region. However, the failure might have been aided by hydrogen rich medium and soft C-depleted ferrite region.     

Microstructure and mechanical properties of diffusion bonded SiC/steel joint using W/Ni interlayer

This paper describes the design and examination of W/Ni double interlayer to produce a joint between SiC and ferritic stainless steel. Diffusion bonding was performed by a two steps solid state diffusion bonding process. Microstructural examination and mechanical properties evaluation of the joints show that bonding of SiC to steel was successful. EDS and XRD analysis revealed that W₅Si₃ and WC were formed at SiC/W interface. The diffusion products at W/Ni interface, Ni-rich solid solution Ni(W) or intermetallic compound Ni₄W, was found to be dependent on the second step joining temperature. Neither intermediate phases nor reaction products was observed at Ni/steel interface for the joints bonded at the temperature studied. The average tensile strength of 55 MPa which is insensitive to the second step process was measured for as-bonded SiC/steel joint and the failure occurred at SiC/W interface. The hardness near the various bonded interfaces was also evaluated.     

Microstructural development of diffusion-brazed austenitic stainless steel to magnesium alloy using a nickel interlayer

The differences in physical and metallurgical properties of stainless steels and magnesium alloys make them difficult to join using conventional fusion welding processes. Therefore, the diffusion brazing of 316L steel to magnesium alloy (AZ31) was performed using a double stage bonding process. To join these dissimilar alloys, the solid-state diffusion bonding of 316L steel to a Ni interlayer was carried out at 900 °C followed by diffusion brazing to AZ31 at 510 °C. Metallographic and compositional analyses show that a metallurgical bond was achieved with a shear strength of 54 MPa. However, during the diffusion brazing stage B₂ intermetallic compounds form within the joint and these intermetallics are pushed ahead of the solid/liquid interface during isothermal solidification of the joint. These intermetallics had a detrimental effect on joint strengths when the joint was held at the diffusion brazing temperature for longer than 20 min.     

Microstructure and mechanical properties of diffusion bonded W/steel joint using V/Ni composite interlayer

Diffusion bonding between W and steel using V/Ni composite interlayer was carried out in vacuum at 1050 °C and 10 MPa for 1 h. The microstructural examination and mechanical property evaluation of the joints show that the bonding of W to steel was successful. No intermetallic compound was observed at the steel/Ni and V/W interfaces for the joints bonded. The electron probe microanalysis and X-ray diffraction analysis revealed that Ni₃V, Ni₂V, Ni₂V₃ and NiV₃ were formed at the Ni/V interface. The tensile strength of about 362 MPa was obtained for as-bonded W/steel joint and the failure occurred at W near the V/W interface. The nano-indentation test across the joining interfaces demonstrated the effect of solid solution strengthening and intermetallic compound formation in the diffusion zone.     

Hot pressing diffusion bonding of a titanium alloy to a stainless steel with an aluminum alloy interlayer

The probability and appropriate processing parameters of hot pressing diffusion bonding (HP–DW) of a titanium alloy (TC4) to a stainless steel (1Cr18Ni9Ti) with an aluminum alloy (LF6) interlayer have been investigated. The microstructure of the bonded joints has been observed by optical microscopy, SEM, XRD and EDX, and the main factors affecting hot pressing and diffusion bonding process were analyzed. The results showed that atom diffused well and no intermetallic compound or other brittle compounds appeared at optimum parameters. The fracture way of joints was ductile fracture. With the increment of bonding temperature, large number of intermetallic compounds such as FeAl₆, Fe₃Al, FeAl₂ which were brittle appeared along the interface between the stainless steel and the aluminum alloy interlayer, as a result, the quality of joints was decreased significantly and the fracture way of joints was brittle fracture.     

316L不锈钢扩散连接接头界面疲劳裂纹扩展行为

采用单边缺口试样对316L不锈钢扩散连接接头进行显微疲劳试验,实现微观尺度下界面裂纹扩展和微孔隙演化的原位观测.试验观察表明:动载荷下界面裂纹扩展时,裂纹尖端晶粒内产生局部的塑性变形,但几乎观测不到界面微孔隙的扩展,也未见微孔隙与微孔隙的相连;微孔隙对界面裂纹萌生和扩展的影响不大;扩散连接过程中所形成的谷脊状界面可以改变裂纹的扩展路径.     

Mechanical properties of 304L stainless steel SMAW joints under dynamic impact loading

The impact properties of 304L Stainless Steel Shielded Metal Arc Welded (SMAW) joints are studied at strain rates between 10^{− 3} and 7.5× 10³ s^{− 1} using a compressive split-Hopkinson bar. The effects of strain rate on the flow response and fracture characteristics are fully evaluated. The results show that the tested weldments exhibit a pronounced strain rate sensitivity, and that changes in the strain rate result in a difference in the flow stress, fracture strain, and work hardening rate. Furthermore, it is noted that the strain rate sensitivity and activation volume vary with the magnitude of the strain rate, and are related to different work hardening stress levels. At all values of strain rate, the tested weldments fail as a result of adiabatic shearing, in which cracks initiate within the shear band and then propagate along this shear band until failure occurs. Observation of the fractured specimens reveals that the fracture surfaces of the fusion zone and base metal regions are characterized by the presence of elongated dimples. The variation in the observed dimple features with strain rate is consistent with the results of the impact stress-strain curves.     

Effect of interface microstructure on the bond strength of the diffusion welded joints between titanium and stainless steel

Diffusion bonding between commercially pure titanium and 304 stainless steel was carried out at a temperature of 950 °C for 30–120 min under uniaxial load in a vacuum. The diffusion bonds were characterized by optical and scanning electron microscopy. The diffusion zone contained different reaction bands and their chemical composition was determined using energy dispersive X-ray spectroscopy. The concentration of chemical species indicated the presence of σ, λ, χ, FeTi, β-Ti and Fe₂Ti₄O phases in the reaction zone and their existence was confirmed by X-ray diffraction. A maximum bond strength of 71% of that of titanium along with 5.8% ductility were obtained for the diffusion couple processed for 30 min due to formation of finer size intermetallics. A rise in joining time increases void generation and growth of intermetallic compounds, which are responsible for a drastic fall in the strength value.     

Impact performance of friction welded butt joints between 6061-T6 aluminium alloy and type 304 stainless steel

Abstract

The tensile strength and energy absorption for dissimilar metal friction welds between 6061-T6 Al alloy and type 304 stainless steel at high rates of loading were determined using the split Hopkinson bar. Cylindrical tensile specimens machined from as welded butt joints of 13 mm in diameter were used in both static and impact tests. Friction welding was conducted using a brake type friction welding machine under two different welding conditions. The effects of welding conditions and loading rate on the joint tensile properties were examined. Results show that the joint tensile properties were greatly affected by the welding parameters, and were slightly enhanced with increased loading rate. Scanning electron microscope observations revealed that the tensile fracture modes in the butt joint specimens varied with loading rate and depend on welding conditions. Microhardness profiles across the weld interface were measured to investigate the extent of the heat affected zone. The slight enhancement of the joint tensile properties with increasing loading rate is primarily attributed to the strain rate dependence of the thermally softened 6061-T6 Al alloy base material.     

Microstructure and mechanical properties of resistance upset butt welded 304 austenitic stainless steel joints

Resistance upset welding (UW) is a widely used process for joining metal parts. In this process, current, time and upset pressure are three parameters that affect the quality of welded products. In the present research, resistance upset butt welding of 304 austenitic stainless steel and effect of welding power and upset pressure on microstructure, tensile strength and fatigue life of the joint were investigated. Microstructure of welds were studied using scanning electron microscopy (SEM). X-ray diffraction (XRD) analysis was used to distinguish the phase(s) that formed at the joint interface and in heat affected zone (HAZ). Energy dispersive spectroscopy (EDS) linked to the SEM was used to determine chemical composition of phases formed at the joint interface. Fatigue tests were performed using a pull–push fatigue test machine and the fatigue properties were analyzed drawing stress-number of cycles to failure (S–N) curves. Also tensile strength tests were performed. Finally tensile and fatigue fracture surfaces were studied by SEM. Results showed that there were three different microstructural zones at different distances from the joint interface and delta ferrite phase has formed in these regions. There was no precipitation of chromium carbide at the joint interface and in the HAZ. Tensile and fatigue strengths of the joint decreased with welding power. Increasing of upset pressure has also considerable influence on tensile strength of the joint. Fractography of fractured samples showed that formation of hot spots at high welding powers is the most important factor in decreasing tensile and fatigue strengths.     

Structure and properties of solid state diffusion bonding of 17-4PH stainless steel and titanium

Abstract

Solid state diffusion bonded joint between titanium and 17-4 precipitation hardening stainless steel was carried out in the temperature range of 800–1050°C in steps of 50°C for 30 min and also at 950°C for 30–180 min in steps of 30 min under a uniaxial pressure of 3·5 MPa in vacuum. Bonded samples were characterised using light microscopy, field emission scanning electron microscopy and X-ray diffraction technique. Up to 850°C for 30 min, FeTi phase was formed at the diffusion interface; however, α-Fe+λ, χ, Fe₂Ti and FeTi phases and phase mixtures were formed above 850°C for 30 min and at 950°C for all bonding times. Maximum tensile strength of ～326 MPa, shear strength of ～254 MPa and impact toughness of ～24 J were obtained for the diffusion couple processed at 1000°C for 30 min and 30–180 min time interval at 950°C, and maximum tensile strength ～323 MPa, shear strength ～243 MPa and impact toughness of ～22 J were achieved when bonding was processed for 120 min. The residual stress of the bonded joints increases with the increase in bonding temperatures and times.