Crystallization, structure and properties of plasticized poly(l-lactide)

Poly(l-lactide) (PLA) was plasticized with poly(ethylene glycol)s having M_w of 400 and 600 g/mol. In addition to poly(ethyne glycol)s with hydroxyl end groups, monomethyl ethers of poly(ethylene glycol) having M_w of 550 and 750 g/mol, with chains terminated with hydroxyl groups and methyl groups, were used. The effect of different end groups on the plasticization of both amorphous and semicrystalline PLA was studied. The crystallization, structure, thermal and tensile properties of PLA and PLA with 5 and 10 wt% of plasticizers were explored. No marked effect induced by different end groups of plasticizers was found. All the plasticizers used decreased T_g and increased the ability of PLA to cold crystallization. While an amorphous plasticized PLA could be deformed to about 550%, a semicrystalline PLA with the same total plasticizer content exhibited nonuniform plasticization of the amorphous phase and less ability to the plastic deformation. Nevertheless, a 20% elongation at break was achieved for a semicrystalline PLA with 10 wt% of the plasticizer. The plastic deformation of both neat and plasticized PLA was associated with crazing.     

Aging of poly(lactide)/poly(ethylene glycol) blends. Part 2. Poly(lactide) with high stereoregularity

Blending poly(ethylene glycol) (PEG) with poly(lactide) (PLA) decreases the T_g and improves the mechanical properties. The blends have lower modulus and increased fracture strain compared to PLA. However, the blends become increasingly rigid over time at ambient conditions. Previously, it was demonstrated that a PLA of lower stereoregularity was miscible with up to 30 wt% PEG. Aging was due to slow crystallization of PEG from the homogeneous amorphous blend. Crystallization of PEG depleted the amorphous phase of PEG and gradually increased the T_g until aging essentially ceased when T_g of the amorphous phase reached the aging temperature. In the present study, this aging mechanism was tested with a crystallizable PLA of higher stereoregularity. Changes in thermal transitions, solid state structure, and mechanical properties were examined over time. Blends with up to 20 wt% PEG were miscible. Blends with 30 wt% PEG could be quenched from the melt to the homogenous amorphous glass. However, this composition phase separated at ambient temperature with little or no crystallization. Changes in mechanical properties during phase separation reflected increasing rigidity of the continuous PLA-rich phase as it became richer in PLA. Construction of a phase diagram for blends of higher stereoregular PLA with PEG was attempted.     

The effect of poly(ethylene glycol) as plasticizer in blends of poly(lactic acid) and poly(butylene succinate)

The effect of polyethylene glycol (PEG) on the mechanical and thermal properties of poly(lactic acid) (PLA)/poly(butylene succinate) (PBS) blends was examined. Overall, it was found that PEG acted as an effective plasticizer for the PLA phase in these microphase‐separated blends, increasing the elongation at break in all blends and decreasing the T_g of the PLA phase. Significant effects on other properties were also observed. The tensile strength and Young's modulus both decreased with increasing PEG content in the blends. In contrast, the elongation at break increased with the addition of PEG, suggesting that PEG acted as a plasticizer in the polymer blends. Scanning electron microscope images showed that the fracture mode of PLA changed from brittle to ductile with the addition of PEG in the polymer blends. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43044.     

Intermolecular interactions and crystallization behaviors of biodegradable polymer blends between poly (3-hydroxybutyrate) and cellulose acetate butyrate studied by DSC, FT-IR, and WAXD

Relationships between composition- and temperature-dependent intermolecular interactions and cold crystallization behaviors of poly(3-hydroxybutyrate) (PHB)/ cellulose acetate butyrate (CAB) blends have been investigated mainly by infrared (IR) spectroscopy, together with differential scanning calorimetry, and wide-angle X-ray diffraction (WAXD). Weak intermolecular hydrogen bondings between OH groups in CAB and CO groups in amorphous part of PHB define as inter were detected in OH stretching bands of the blends. These interactions occur in the blends with high CAB content (w_CAB) and highly depend on temperature. For all the blends having 0.2 ≤ w_CAB ≤ 0.7, when temperature is raised (e.g., above 90 °C for the blend with w_CAB = 0.5) the cold crystallization of PHB was discerned, as evidenced by an increase of the absorbance of the band due to CO stretching in the crystal field. The crystallization was found to involve the dissociation of inter and transformation of inter into intramolecular hydrogen bondings within PHB and within CAB as summarized in Table 2 in this text, which promotes the crystallization and enhances stabilization of the crystals. Consequently, the crystallization of the PHB is influenced by exchanges of the hydrogen bondings as described above with raising temperatures. X-ray diffraction from PHB crystals in the blends show a remarkable decrease of crystallinity with w_CAB and eventually disappear when w_CAB ≥ 0.8.     

Aging of poly(lactide)/poly(ethylene glycol) blends. Part 1. Poly(lactide) with low stereoregularity

Poly(lactide) (PLA) is rapidly gaining interest as a biodegradable thermoplastic for general usage in degradable disposables. To improve mechanical properties, a PLA with low stereoregularity was blended with polyethylene glycol (PEG). Blends with up to 30 wt% PEG were miscible at ambient temperature. Blending with PEG significantly decreased the T_g, decreased the modulus and increased the fracture strain of PLA. However, the PLA/PEG 70/30 blend became increasingly rigid over time at ambient conditions. The mechanism of aging primarily under ambient conditions of temperature and humidity was studied. Changes in mechanical properties, thermal transitions and solid state morphology were examined over time. Aging was caused by slow crystallization of PEG. Crystallization of PEG depleted the amorphous phase of PEG and gradually increased the T_g. As T_g approached the aging temperature, reduced molecular diffusivity slowed the crystallization rate dramatically. Aging essentially ceased when T_g of the amorphous phase reached the aging temperature. The increase in matrix T_g and the reinforcing effect of the crystals produced a change in mechanical properties from elastomer-like to thermoplastic-like.     

Mechanical properties, morphologies, and crystallization behavior of plasticized poly(l-lactide)/poly(butylene succinate-co-l-lactate) blends

The blends of poly(l-lactide) (PLLA) with poly(butylene succinate-co-l-lactate) (PBSL) containing the lactate unit of ca. 3 mol% and Rikemal PL710 (RKM) which is a plasticizer mainly composed of diglycerine tetraacetate were prepared by melt-mixing and subsequent injection molding. The studied RKM content of the PLLA/PBSL/RKM blends was 0-20 wt%, and the PLLA/PBSL weight ratio was 100/0 to 80/20. Although elongation at break in the tensile test did not increase by the addition of 10 wt% RKM to PLLA, the addition of a small amount of PBSL to the PLLA/RKM blend caused a considerable increase of the elongation. The SEM and DSC analyses revealed that all the PLLA/PBSL/RKM blends are immiscible blends where the PBSL particles are finely dispersed, and that there is some compatibility between PLLA-rich phase and PBSL-rich phase in the amorphous state when the RKM content is 20 wt%. As a result of investigation of the crystallization behavior by DSC and polarized optical microscopic measurements, it was revealed that the addition of RKM causes the acceleration of crystalline growth rate at a lower annealing temperature, and the addition of PBSL mainly enhances the formation of PLLA crystal nucleus.     

Crystallization and morphology of stereocomplexes in nonequimolar mixtures of poly(l-lactic acid) with excess poly(d-lactic acid)

Crystallization of nonequimolar compositions of poly(d-lactic acid) with low-molecular-weight poly(l-lactic acid) (PDLA/LM_w-PLLA) blends leads to formation of various fractions of stereocomplexed PLA (sc-crystallites) and homocrystallites (PDLA or PLLA). For the PDLA/LM_w-PLLA blends within the composition window of LM_w-PLLA content between 30 and 50 wt%, only sc-crystal exists and no homocrystal is present. On the other hand, for PDLA/LM_w-PLLA blends with excess PDLA, e.g. PDLA/LM_w-PLLA = 90/10, atomic-force microscopy (AFM) characterization on various stages of crystallization of sc-PLA crystal with PDLA homocrystal shows a repetitive stacking of excess PDLA on pre-formed sc-PLA crystal serving as crystallizing templates. The crystallization initially begins with string-like (fibril-like) PDLA lamellae, followed with PDLA aggregating on sc-PLA crystal into a bead-on-string crystal, then growing to thicker irregularly-shaped dough-like lamellae. Repetitive growth cycle from strings to bead-on-string lamellae continues on top of the dough-like lamellae as new substrates, until ending impingement of the PDLA spherulites.     

Crystallization behavior of poly(l-lactic acid) affected by the addition of a small amount of poly(3-hydroxybutyrate)

The miscibility, crystallization and subsequent melting behavior in binary biodegradable polymer blends of poly(l-lactic acid) (PLLA) and low molecular weight poly(3-hydroxybutyrate) (PHB) have been investigated by differential scanning calorimetry (DSC), Fourier-transform infrared (FTIR) spectroscopy, and wide-angle X-ray diffraction (WAXD). DSC analysis results indicted that PLLA showed no miscibility with high molecular weight PHB (M_w = 650,000 g mol⁻¹) in the 80/20, 60/40, 40/60, 20/80 composition range of the PHB/PLLA blends. On the other hand, it showed some limited miscibility with low molecular weight PHB (M_w = 5000 g mol⁻¹) when the PHB content was below 25%, as evidenced by small changes in the glass transition temperature of PLLA. The partial miscibility was further supported by changes of cold-crystallization behavior of PLLA in the blends. During the nonisothermal crystallization, it was found that the addition of a small amount of PHB up to 30% made the cold-crystallization of PLLA occur in the lower temperature. Meanwhile, the crystallization of PHB and PLLA was observed in the heating process by monitoring characteristic IR bands of each component for the low molecular weight PHB/PLLA 20/80 and 30/70 blends. The temperature-dependent IR and WAXD results also revealed that for PLLA component crystallization, the disorder (α′) phase of PLLA was produced, and that the α′ phase changed to the order (α) phase just prior to the melting point.     

Tributyl citrate oligomers as plasticizers for poly (lactic acid): thermo-mechanical film properties and aging

Poly (lactic acid), PLA, is a biodegradable thermoplastic that can be produced from renewable resources. The polymer is of interest for production of films for packaging applications. However, plasticization of PLA is required in order to obtain films with sufficient flexibility. PLA was blended with tributyl citrate (TbC) and two oligomers of TbC that were synthesized by transesterification of tributyl citrate (TbC) and diethylene glycol (DEG). Dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC) were used to investigate the dynamic mechanical and thermal properties of the blends. All the plasticizers investigated decreased the glass transition temperature of PLA, and the reduction was the largest with the plasticizer having the lowest molecular weight. The PLA matrix became saturated with plasticizer at a certain concentration and phase separation occurred; the higher the molecular weight of the plasticizer, the lower the saturation concentration. Aging of the blends at room temperature for several months induced partial phase separation in the material. It was observed that the morphological stability of the blends was enhanced when the plasticizer concentration was reasonably low, i.e. 10-15 wt%.     

Miscibility and crystallization in crystalline/crystalline blends of poly(butylene succinate)/poly(ethylene oxide)

Miscibility and crystallization behavior have been investigated in blends of poly(butylene succinate) (PBSU) and poly(ethylene oxide) (PEO), both semicrystalline polymers, by differential scanning calorimetry and optical microscopy. Experimental results indicate that PBSU is miscible with PEO as shown by the existence of single composition dependent glass transition temperature over the entire composition range. In addition, the polymer-polymer interaction parameter, obtained from the melting depression of the high-T_m component PBSU using the Flory-Huggins equation, is composition dependent, and its value is always negative. This indicates that PBSU/PEO blends are thermodynamically miscible in the melt. The morphological study of the isothermal crystallization at 95 °C (where only PBSU crystallized) showed the similar crystallization behavior as in amorphous/crystalline blends. Much more attention has been paid to the crystallization and morphology of the low-T_m component PEO, which was studied through both one-step and two-step crystallization. It was found that the crystallization of PEO was affected clearly by the presence of the crystals of PBSU formed through different crystallization processes. The two components crystallized sequentially not simultaneously when the blends were quenched from the melt directly to 50 °C (one-step crystallization), and the PEO spherulites crystallized within the matrix of the crystals of the preexisted PBSU phase. Crystallization at 95 °C followed by quenching to 50 °C (two-step crystallization) also showed the similar crystallization behavior as in one-step crystallization. However, the radial growth rate of the PEO spherulites was reduced significantly in two-step crystallization than in one-step crystallization.     

Mechanical properties, morphology, and crystallization behavior of blends of poly(l-lactide) with poly(butylene succinate-co-l-lactate) and poly(butylene succinate)

The blends of poly(l-lactide) (PLLA) with poly(butylene succinate) (PBS) and poly(butylene succinate-co-l-lactate) (PBSL) containing the lactate unit of ca. 3 mol% were prepared by melt-mixing and subsequent injection molding, and their mechanical properties, morphology, and crystallization behavior have been compared. Dynamic viscoelasticity and SEM measurements of the blends revealed that the extent of the compatibility of PBSL and PBS with PLLA is almost the same, and that the PBSL and PBS components in the blends with a low content of PBSL or PBS (5-20 wt%) are homogenously dispersed as 0.1−0.4 μm particles. The tensile strength and modulus of the blends approximately followed the rule of mixtures over the whole composition range except that those of PLLA/PBS 99/1 blend were exceptionally higher than those of pure PLLA. All the blends showed considerably higher elongation at break than pure PLLA, PBSL, and PBS. Differential scanning calorimetric analysis of the blends revealed that the isothermal and non-isothermal crystallization of the PLLA component is promoted by the addition of a small amount of PBSL, while the addition of PBS was much less effective.     

Thermal analysis of disulfonated poly(arylene ether sulfone) plasticized with poly(ethylene glycol) for membrane formation

One route to melt processing of high glass transition temperature polyelectrolytes, such as disulfonated poly(arylene ether sulfone) (BPS), involves mixing a plasticizer with the polymer. In this study, poly(ethylene glycol) (PEG) was used as a plasticizer for BPS. BPS and PEG are miscible, and the effect of PEG molecular weight (in the range of 200–600 g/mol) and concentration on the T_g of BPS/PEG blends was investigated. As PEG molecular weight decreases and concentration increases, the blend T_g is depressed significantly. Based on isothermal holds in a rheometer at various temperatures and times, the PEG materials considered were thermally stable up to 220 °C for 10 min in air or 250 °C for at least 10 min under a nitrogen atmosphere, which is long enough to permit melt extrusion of such materials.     

三醋酸甘油酯增塑聚乳酸共混体系热力学及动态力学性质

用三醋酸甘油酯(TA c)增塑聚乳酸(PLA),研究了TA c对PLA力学性能的影响。当塑化剂添加到15%之后抗张强度从64M Pa下降到29.9M Pa,断裂伸长率同时从5.6%升高到243.1%,可以达到吹膜所要求的性质。用DSC和DM A研究了该共混体系的相容性,观察到随着TA c含量的增大,线性降低了PLA的Tg和Tm,并且塑化剂提高了分子链的迁移性,也使得体系的结晶度增大。在塑化剂含量为25%时,PLA已经被塑化剂所饱和,继续添加塑化剂可能会导致两相分离。     

Stiffer and super-tough poly(butylene terephthalate) based blends by modification with phenoxy and maleated poly(ethylene-octene) copolymers

New super-tough poly(butylene terephthalate) (PBT) materials were obtained by melt blending PBT with both 20 wt% phenoxy (Ph) and 0-30 wt% maleic anhydride grafted poly(ethylene-octene) (mPEO) copolymers with different grafting levels. Ph was completely miscible in the PBT matrix. The presence of mPEO did not influence either the nature of the PBT-Ph matrix or the crystallization of PBT. The overall decrease in particle size and in interfacial tension upon grafting indicated that compatibilization had taken place. Super-tough (impact strength 23-fold that of the PBT) and stiffer PBT based blends were obtained at mPEO contents equal to or higher than 15%. The dependence of the critical inter-particle distance (τ_c), on both adhesion measured by means of the interfacial tension, and on the relation between the modulus of the matrix and that of the rubbery dispersed phase (E_m/E_d), is proposed.     

Effect of nucleation and plasticization on the crystallization of poly(lactic acid)

In this paper, different strategies to promote PLA crystallization were investigated with the objective of increasing the crystalline content under typical polymer processing conditions. The effect of heterogeneous nucleation was assessed by adding talc, sodium stearate and calcium lactate as potential nucleating agents. The PLA chain mobility was increased by adding up to 10 wt% acetyl triethyl citrate and polyethylene glycol as plasticizers. The crystallization kinetics were studied using DSC analysis under both isothermal and non-isothermal conditions. The isothermal data showed that talc is highly effective in nucleating the PLA in the 80-120 °C temperature range. In the non-isothermal DSC experiments, the crystallinity developed upon cooling was systematically studied at cooling rates of 10, 20, 40, and 80 °C/min. The non-isothermal data showed that the combination of nucleant and plasticizer is necessary to develop significant crystallinity at high cooling rates. The nucleated and/or plasticized PLA samples were injection molded and the effect of mold temperature on crystallinity was determined. It was possible to mold the PLA formulations using mold temperatures either below 40 °C or greater than 60 °C. At low temperature, the molded parts were nearly amorphous while at high mold temperatures, the PLA formulation with proper nucleation and plasticization was shown to achieve crystallinity levels up to 40%, close to the maximum crystalline content of the material. Tensile mechanical properties and temperature resistance of these amorphous and semi-crystalline materials were examined.     

Study of crystalline and amorphous phases of biodegradable poly(lactic acid) by advanced thermal analysis

The qualitative and quantitative thermal analysis of biodegradable poly(lactic acid) PLA is presented. The glass transition, melting process, and heat capacity of a semi-crystalline poly(lactic acid) are studied utilizing the differential scanning calorimetry and temperature-modulated DSC. The mobile amorphous fraction, W_a degree of crystallinity, W_c and rigid-amorphous fraction, W_RAF were estimated depending on the thermal history of semi-crystalline PLA. From qualitative thermal analysis, the glass transition of rigid-amorphous phase was observed as a broadening from the changes of heat-flow-rate between mobile glass transition temperature and melting temperature. The amount of the rigid-amorphous fraction (RAF) was evaluated from W_RAF = 1−W_c − W_a and graphically was presented as the result of a deflection from the linearity of the dependence of the change of degree of mobile amorphous phase (W_a) vs. the degree of crystalline fraction (W_c) for semi-crystalline PLA with different thermal history. The degree of crystallinity of semi-crystalline samples of PLA can be discussed in terms of a two- or three-phase model. In contrast, the quantitative thermal analysis of the experimental apparent heat capacity of semi-crystalline PLA did not show any appearance of RAF in the examples of analyzed samples. The experimental heat capacity of PLA was analyzed in reference to the solid and liquid equilibrium heat capacities of poly(lactic acid) found in the ATHAS Data Bank.     

Effects of molecular weight on poly(ω-pentadecalactone) mechanical and thermal properties

A series of poly(ω-pentadecalactone) (PPDL) samples, synthesized by lipase catalysis, were prepared by systematic variation of reaction time and water content. These samples possessed weight-average molecular weights (M_w), determined by multi-angle laser light scattering (MALLS), from 2.5 × 10⁴ to 48.1 × 10⁴. Cold-drawing tensile tests at room temperature of PPDL samples with M_w between 4.5 × 10⁴ and 8.1 × 10⁴ showed a brittle-to-ductile transition. For PPDL with M_w of 8.1 × 10⁴, inter-fibrillar slippage dominates during deformation until fracture. Increasing M_w above 18.9 × 10⁴ resulted in enhanced entanglement network strength and strain-hardening. The high M_w samples also exhibited tough properties with elongation at break about 650% and tensile strength about 60.8 MPa, comparable to linear high density polyethylene (HDPE). Relationships among molecular weight, Young's modulus, stress, strain at yield, melting and crystallization enthalpy (by differential scanning calorimetry, DSC) and crystallinity (from wide-angle X-ray diffraction, WAXD) were correlated for PPDL samples. Similarities and differences of linear HDPE and PPDL molecular weight dependence on their mechanical and thermal properties were also compared.     

One-pot synthesis and characterization of aliphatic poly(oxytetramethylene) ionene

One-pot synthesis of poly(oxytetramethylene) ionene (POI) composed of one dimethylammonium group in each repeating unit is described. POI was prepared by using the cationic polymerization of tetrahydrofuran, followed by the chain extension reaction of living poly(oxytetramethylene) (POTM) chain with N,N-dimethylaminotrimethylsilane. The weight average molecular weight of the ionene with bromide counter-anion (POI-Br) was 48,000 g/mol and the molecular weight of POTM between the ionic sites was ca. 2100. POI-Br showed polyelectrolyte behavior in polar solvent. The elastomeric film of POI-Br was prepared: its tensile strength at break and elongation at break were ca. 11 MPa and ca. 1900% at 19 °C, respectively. Small-angle X-ray scattering, differential scanning calorimetry and dynamic mechanical analysis suggested the formation of microphase-separated structure for POI-Br film.     

Synthesis and properties of polymer brush consisting of poly(phenylacetylene) main chain and poly(dimethylsiloxane) side chains

A novel polymer brush consisting of poly(phenylacetylene) (PPA) main chain and poly(dimethylsiloxane) (PDMS) side chains was synthesized by the polymerization of phenylacetylene-terminated PDMS macromonomer (M-PDMS). The macromonomer was prepared by the esterfication of monohydroxy-ended PDMS (PDMS-OH, degree of polymerization (DP) = 42) with p-ethynylbenzoic acid. The polymerization of M-PDMS using [(nbd)RhCl]₂/Et₃N catalyst led to polymer brush, poly(M-PDMS), with M_n up to 349?000 (DP of main chain 104). Poly(M-PDMS) with narrow molecular weight distribution (M_n = 39?900, M_w/M_n = 1.11) was obtained with a vinyl-Rh catalyst, [Rh{C(Ph)CPh₂}(nbd){P(4-FC₆H₄)₃}]/(4-FC₆H₄)₃P. Poly(M-PDMS)s were brown to orange viscous liquids and soluble in organic solvents such as toluene and CHCl₃. The UV-vis absorptions of poly(M-PDMS) were observed in the range of 350-525 nm, which are attributable to the PPA main chain.     

Small-angle neutron scattering from symmetric blends of poly(dimethylsiloxane) and poly(ethylmethylsiloxane)

We present results of a small-angle neutron scattering (SANS) study of the structure and thermodynamic properties of symmetric blends of deuterated poly(dimethylsiloxane) (d-PDMS) and poly(ethylmethylsiloxane) (PEMS) as a function of temperature (T) (40≤T≤300 °C) and the molecular weight (M_w) (4700≤M_w≤23,200). The radius of gyration (R_g) of d-PDMS was measured using the high-concentration labeling method and revealed unperturbed chain dimensions at all temperatures regardless of the polymer M_w. The random phase approximation (RPA) fits the data for low M_w blends, however it fails to describe the SANS data for M_w>10,000 g/mol. This observation is explained by the fact that for high M_w blends the correlation length of the concentration fluctuations ξ is always large (ξ>R_g), implying that these blends remain microscopically inhomogeneous at all temperatures studied in this work. At the same time, the low M_w blends are randomly mixed (ξ<R_g) at all T and can reach the ‘ideal mixing’ or Θ condition (χ=0).