Dopant-dependent variation in the distribution of polarons and bipolarons as charge-carriers in polypyrrole thin films synthesized by oxidative chemical polymerization

A study on the distribution of polarons vs. bipolarons as charge carriers in polypyrrole thin films doped with different dopant anions (chloride, p-toluenesulfonate and anthraquinone-2-sulfonate) is presented in this paper. The polypyrrole thin films synthesized by oxidative chemical polymerization have comparable thickness in the range of 80–100 nm. However, with the variation of the dopant anion, the conductivity of the polypyrrole thin films can differ by three orders of magnitude. The conductivity of polypyrrole thin films doped with chloride, p-toluenesulfonate and anthraquinone-2-sulfonate is 0.64 S/cm, 7.1 S/cm and 120 S/cm, respectively. The Raman spectroscopy and electron spin resonance (ESR) spectroscopy results show that (i) both polarons and bipolarons are present in the three types of polypyrrole thin films and (ii) the distribution of polarons vs. bipolarons as charge carriers in polypyrrole varies with the dopant anion used. The overall study reveals that the charge carriers in the anthraquinone-2-sulfonate-doped polypyrrole thin film are mainly spinless bipolarons, whereas the charge carriers in the chloride-doped polypyrrole thin film are dominated by paramagnetic polarons.     

Electrodeposited PbO2 thin film as positive electrode in PbO2/AC hybrid capacitor

Lead dioxide (PbO₂) thin films were prepared on Ti/SnO₂ substrates by means of electrodeposition method. Galvanostatic technique was applied in PbO₂ film formation process, and the effect of deposition current on morphology and crystalline form of the PbO₂ thin films was studied by means of scanning electron microscopy (SEM) and X-ray diffraction (XRD). The energy storage capacity of the prepared PbO₂ electrode was investigated by means of cyclic voltammetry (CV) and charge/discharge cycles, and a rough surface structure PbO₂ film was selected as positive electrode in the construction of PbO₂/AC hybrid capacitor in a 1.28 g cm⁻³ H₂SO₄ solution. The electrochemical performance was determined by charge/discharge tests and electrochemical impedance spectroscopy (EIS). The results showed that the PbO₂/AC hybrid capacitor exhibited high capacitance, good cycling stability and long cycle life. In the voltage range of 1.8-0.8 V during discharge process, considering the weight of all components of the hybrid capacitor, including the two electrodes, current collectors, H₂SO₄ electrolyte and separator, the specific energy and power of the device were 11.7 Wh kg⁻¹ and 22 W kg⁻¹ at 0.75 mA cm⁻², and 7.8 Wh kg⁻¹ and 258 W kg⁻¹ at 10 mA cm⁻² discharge currents, respectively. The capacity retains 83% of its initial value after 3000 deep cycles at the 4 C rate of charge/discharge.     

Facile electrosynthesis of novel free-standing electroactive poly((S)-(−)-1,1′-bi-2-naphthol dimethyl ether) films with enhanced main chain axial chirality

Direct anodic oxidation of (S)-(−)-1,1′-bi-2-naphthol dimethyl ether (BNME) in CH₂Cl₂/CHCl₃ containing boron trifluoride diethyl etherate (BFEE) as the supporting electrolyte led to facile electrodeposition of high-quality free-standing poly((S)-(−)-1,1′-bi-2-naphthol dimethyl ether) (PBNME) film on stainless steel (SS)/indium tin oxide (ITO) electrodes. As-formed PBNME films showed good electroactivity and redox stability in CH₂Cl₂-BFEE, BFEE, and even in concentrated sulfuric acid. Both doped and dedoped PBNME films were partly soluble in strong polar solvents, such as dimethyl sulfoxide (DMSO). Quantum chemistry calculations of BNME and FT-IR spectrum of dedoped PBNME films demonstrated that the polymerization probably occurred at 4- and 4′-positions. Optical rotation determination showed that the conformation of the monomer was maintained during the electrochemical polymerization process and the polymer exhibited greatly enhanced optical rotation value with main chain axial chirality compared with that of the monomer. Fluorescent spectral studies indicated that soluble PBNME was a good blue-light emitter with maximum emission at 415 nm and fluorescence quantum yield of 0.15, while solid-state PBNME film showed its emission centered at 380 nm. Furthermore, as-formed PBNME manifested favorable thermal stability and relatively high electrical conductivity of about 10⁻¹ S cm⁻¹ at room temperature.     

Thermally induced conformational and structural disordering in polyethylene crystal studied by near-infrared spectroscopy

Thermally induced structural and conformational changes in polyethylene (PE) samples were explored by using near-infrared (NIR) spectroscopy. The differences in the temperature-dependent structural disordering process among six PE samples were depicted by monitoring the intensities of NIR bands characteristic of orthorhombic crystalline phase. The temperature dependency of bands in the NIR region that have been considered to be due to orthorhombic crystalline lattice was compared to that of a band at 1378 cm⁻¹ due to the methyl symmetric bending mode. The intensity decrease of the band in the mid-infrared (MIR) region seems to sensitively reflect the overall disordering of orthorhombic crystalline structure. As a result of this study, the intensity decrease of the bands in the NIR spectral region was found to proceed at lower temperature than that of the band at 1378 cm⁻¹. This finding suggests the status of orthorhombic crystalline structure probed by the intensity of the band at 1378 cm⁻¹ and that by the “crystalline” bands in the NIR spectral region may not be identical. The NIR spectra were further analyzed by two-dimensional (2D) correlation spectroscopy to provide the in-depth analysis of NIR bands. The 2D correlation spectroscopy has detected the presence of two NIR bands at 4342 and 4290 cm⁻¹ due to orthorhombic crystalline phase and those at 5840 and 5640 cm⁻¹ due to amorphous phase. The hetero-spectral 2D correlation analysis was carried out between the NIR spectral region of 4365-4240 cm⁻¹ and the well-established MIR spectral region for CH₂ wagging deformation region of 1390-1240 cm⁻¹, where bands due to nonplanar conformer are detected. This approach allowed us to determine NIR bands, which behave in a way similar to MIR bands originating from conformational defect sequences that exist in the orthorhombic crystalline lattice, the amorphous domain and the chain fold regions. As a result of the hetero-spectral 2D NIR-MIR correlation spectroscopic studies on the development of conformational defect sequence in three types of PE samples, it was concluded that the intensity of a band at 4265 cm⁻¹ changes in the same manner as the MIR bands at 1368, 1353 and 1308 cm⁻¹ assignable to gtg, gg and gtg′ (kink) conformations. This finding means that the state of conformational disorder in PE crystal can be studied by monitoring the intensity of the NIR band at 4265 cm⁻¹. The use of NIR spectroscopy makes it possible to directly probe the degree in the formation of conformational defect sequences in thick PE products typically produced in industry, which cannot be studied by MIR spectroscopy. This paper thus provides in-depth fundamental understandings on NIR spectra of PE as well as the results of our study regarding structural and conformational changes in PE crystals probed by NIR spectroscopy.     

Electrocatalytic oxidation of deoxyguanosine on a glassy carbon electrode modified with a ruthenium oxide hexacyanoferrate film

The electrocatalytic oxidation of deoxyguanosine on a ruthenium hexacyanoferrate (RuOHCF) glassy carbon (GC) modified electrode was investigated in acid medium by using rotating disc electrode (RDE) voltammetry. Chronoamperometric experiments allowed information on the charge transport rate through the RuOHCF film and at a very short time window a diffusion-like behavior was observed with a D_ct value of 2.7 × 10⁻¹¹ cm² s⁻¹ for a film with Γ = 4.47 × 10⁻⁹ mol cm⁻². The influence of systematic variation of rotation rate, film thickness and the electrode potential indicates that the rate of cross-chemical reaction between Ru(IV) centers immobilized into the film and deoxyguanosine controls the overall electrodic process and the value of the rate constant was found to be 3.2 × 10⁶ mol⁻¹ L¹ s⁻¹. The relatively high rate constant of the cross-reaction, the facile penetration of the substrate through the film and the fast transport of electrons suggest that the electrocatalytic process occurs throughout the film layer.     

Orientation of graphitic planes during annealing of “dip deposited” amorphous carbon film: A carbon K-edge X-ray absorption near-edge study

Annealing effect of amorphous carbon thin films on Si(1 0 0) substrates is studied by normal incidence and angle dependent carbon K-edge X-ray absorption near-edge structure (XANES) spectroscopy. The angle dependence of the XANES signal shows that the graphitic basal planes are oriented perpendicular to the surface when the film is annealed at 1000 °C. Micro-Raman spectroscopy reveals two well-separated bands the D band at 1355 cm⁻¹ and G band at ∼1600 cm⁻¹, and their I_D/I_G intensity ratio indicates the formation of more graphitic film at higher annealing temperatures. X-ray diffraction pattern of 1000 °C temperature annealed film confirms the formation of graphite structure.     

Electrochromic performance of a poly(3,4-ethylenedioxythiophene)-Prussian blue device encompassing a free standing proton electrolyte film

Electrochromic devices incorporating an electropolymerized poly(3,4-ethylenedioxythiophene) (PEDOT) film and a free standing, transparent film of a proton conducting polymer electrolyte with high ambient temperature ionic conductivity of 10⁻² S cm⁻¹ have been fabricated with and without the ion storage electrodeposited Prussian blue (PB) counter electrode layer. While coloration efficiency increases as a function of applied potential in the sole PEDOT device with largest values of CE_(max,VIS) ∼ 120 cm² C⁻¹ and CE_(max,NIR) ∼ 133 cm² C⁻¹ attained at V_c = −1.9 V, the PEDOT:PB device shows a digression from this trend. Much higher coloration efficiencies in the visible (247 cm² C⁻¹ at 570 nm) and NIR (116 cm² C⁻¹ at 1100 nm) regions are achieved for the PEDOT:PB device at a relatively lower reducing voltage of −0.8 V. The PEDOT:PB device shows fast switching redox process (t_c = 2.6 s and t_b = 1.3 s for a 50% optical contrast at 632.8 nm) and a highly reversible charge density as the ratio of Q_inserted to Q_extracted was found to vary between 0.8 and 1.0. When switched between the clear and blue states for 2000 cycles, the insignificant drop in peak current density maxima observed for the PEDOT:PB device, i.e. the good cycling stability, the facile fabrication of device assembly, the ease of scaling up the electrolyte and electrochromic coatings, indicate that this method can be adapted as a simple and inexpensive alternative to conventional electrochromic windows with high cost components.     

Facile electrosynthesis of nitro-group-substituted oligopyrene with bicolored emission

Nitro-group-substituted oligopyrene (ONP) film with fairly high electrical conductivity (1.25 × 10⁻¹ S cm⁻¹) and good thermal stability was electrochemically synthesized by direct anodic oxidation of its monomer 1-nitropyrene (NP) in boron trifluoride diethyl etherate (BFEE). The oxidation potential of NP in this medium was determined to be 1.12 V vs. SCE, which was lower than that in acetonitrile +0.1 mol L⁻¹ Bu₄NBF₄ (1.27 V vs. SCE). ONP films obtained from this medium showed good redox activity and structural stability in both BFEE and concentrated sulfuric acid. Fourier transform infrared spectra and theoretical calculations showed that the electropolymerization of the NP monomer mainly occurred at the C(3), C(6) and C(8) positions. The fluorescence spectra suggested that soluble ONP emits strong blue or green fluorescence when excited at 402 nm or 504 nm, respectively. Scanning electron microscopy showed that highly crystalline nitro-group-substituted oligopyrene was formed on the electrode surface. All these results indicate that as-prepared ONP film has many potential applications in various fields.     

Effects of crosslinkers on semi-interpenetrating polymer networks of Nafion and fluorine-containing polyimide

A series of reinforced composite membranes were prepared from Nafion^®212 and crosslinkable fluorine-containing polyimide (FPI) with various crosslinkers. The crosslinkable FPI reacts with the crosslinkers and forms semi-interpenetrating polymer networks (semi-IPN) structure with Nafion^®212. The water uptake, swelling ratio, mechanical properties, thermal behavior, proton conductivity, and chemical oxidation stability of the composite membranes are studied. The degree of crosslinking is characterized by gel fraction of the composite membranes. Compared to pure Nafion^®212, the composite membranes exhibit excellent thermal stability, improved mechanical properties and dimensional stability. The tensile strength of the composite membranes is in the range of 37.3-51.2 MPa. All the composite membranes exhibit high proton conductivity which ranges from 1.9 × 10⁻² to 9.9 × 10⁻² S cm⁻¹. The proton conductivity of the composite membrane with 2-propene-1-sulfonic acid sodium salt (SAS) as the crosslinker is 9.9 × 10⁻² S cm⁻¹ at 100 °C which is similar to that of Nafion^®212 under the same condition.     

Micromolar determination of sulfur oxoanions and sulfide at a renewable sol-gel carbon ceramic electrode modified with nickel powder

The sol-gel technique was used to fabricate nickel powder carbon composite electrode (CCE). The nickel powder successfully used to deposit NiO_x thin film on conductive carbon ceramic electrode for large surface area catalytic application. Repetitive cycling in potential range −0.2 to 1.0 V was used to form of a thin nickel oxide film on the surface carbon composite electrode. The thin film exhibits an excellent electro-catalytic activity for oxidation of SO₃²⁻, S₂O₄²⁻, S₂O₃²⁻, S₄O₆²⁻ and S²⁻ in alkaline pH range 10-14. Optimum pH values for detection of all sulfur derivatives is 13 and catalytic rate constants are in range 2.4 × 10³-8.9 × 10³ M⁻¹ s⁻¹. The hydrodynamic amperometry at rotating modified CCE at constant potential versus reference electrode was used for detection of sulfur derivatives. Under optimized conditions the calibration plots are linear in the concentration range 10 μM-15 mM and detection limit 1.2-34 μM and 0.53-7.58 nA/μM (sensitivity) for electrode surface area 0.0314 cm². The nickel powder doped modified carbon ceramic electrode shows good reproducibility, a short response time (2.0 s), remarkable long term stability, less expense, simplicity of preparation, good chemical and mechanical stability, and especially good surface renewability by simple mechanical polishing and repetitive potential cycling. This sensor can be used into the design of a simple and cheap chromatographic amperometry detector for analysis of sulfur derivatives.     

Thermal analysis and Raman spectroscopic studies of crystallization in poly(ethylene 2,6-naphthalate)

The combination of Fourier transform Raman spectroscopy and thermal analysis has been proved to be adequate for the study of the quantitative structural changes which take place in amorphous poly(ethylene 2,6-naphthalate) on annealing. Different conformer contents were found in the annealed samples depending on annealing conditions. In general, annealing of the amorphous poly(ethylene 2,6-naphthalate) from the glassy state induces a conformational transition of gauche to trans. The structure obtained during crystallization is characterized by a three-phase conformational model, including an amorphous phase, a rigid amorphous phase and a crystalline phase. The crystallization is further characterized by a three-zone process, firstly a primary crystallization process, secondly a variation of the rigid amorphous phase with a constant value of the crystalline phase and thirdly a secondary crystallization process. The bandwidth at half intensity at 1721 cm⁻¹ in the Raman spectrum varied between 32 cm⁻¹ for the complete amorphous phase and 7 cm⁻¹ for the total rigid phase, the sum of the rigid amorphous and crystalline phase. The bandwidth at half intensity at 1721 cm⁻¹ was directly related to the amount of the total rigid phase and confirmed by the variation of the heat capacity increase at the glass transition temperature. Two complementary bands in the Raman spectrum, at 1107 and 1098 cm⁻¹, were found to be related to the trans and gauche isomers. A difference was measured between the total trans content and the amount of rigid phase due to the presence of some trans conformations in the amorphous phase. The extrapolation of the bandwidth at half intensity at 1721 cm⁻¹ to the value of zero, corresponding to the complete crystalline phase, gave a melting enthalpy of 196 J/g and the corresponding density of the crystalline phase was 1.4390 g/cm³. A complete rigid phase structure was obtained by a melting enthalpy of 144 J/g and a density of 1.4070 g/cm³.     

Improving the rate performance of LiFePO4 by Fe-site doping

LiFePO₄ doped by bivalent cation in Fe-sites show improved rate performance and cyclic stability. Under 10 C rate at room temperature, the capacities of LiFe_0.9M_0.1PO₄ (M = Ni, Co, Mg) maintain at 81.7, 90.4 and 88.7 mAh/g, respectively, in comparison with 53.7 mAh/g for undoped LiFePO₄ and 54.8 mAh/g for carbon-coated LiFePO₄ (LiFePO₄/C). The capacity retention is 95% after 100 cycles for doped samples while this value is only 70% for LiFePO₄ and LiFePO₄/C. Such a significant improvement in electrochemical performance should be partially related to the enhanced electronic conductivities (from 2.2 × 10⁻⁹ to <2.5 × 10⁻⁷ S cm⁻¹) and probably the mobility of Li⁺ ions in the doped samples.     

Electrochromic properties of poly{3-[12-(p-methoxyphenoxy)dodecyl]thiophene}

Poly{3-[12-(p-methoxyphenoxy)dodecyl]thiophene} films with different thickness were potentiostatically deposited on optically transparent glass electrodes using different deposition charges. Their spectroelectrochemical properties were studied as a function of thickness, i.e., deposition charge. Films obtained with a deposition charge of ca. 65 mC cm⁻² presented more stability to a high number of redox cycles (>1000), chromatic contrast of 40% at 725 nm, coulombic efficiency of 80% and good optical memory in the reduced state (E=0.0 V). The surface morphology of these films was also characterized by atomic force microscopy. Films obtained with a deposition charge ≤65 mC cm⁻² are homogeneous, while above this value the film surface morphology presents roughness and irregularities. Correlation between deposition charge and film thickness was estimated using a rugosimeter and atomic force microscopy experiments.     

Spectroelectrochemical characterisation of copper salen-based polymer-modified electrodes

Electrogenerated polymers based on copper salen-type complexes were characterised electrochemically and by in situ UV-vis and ex situ EPR spectroscopy. The films, poly[Cu(salen)] and poly[Cu(saltMe)], exhibit reversible oxidative electrochemical behaviour in a wide potential range (0.0-1.5 V). Different regimes for charge transport behaviour are accessed by manipulation of film thickness and experimental time scale: thin films (surface concentration, Γ < ca. 80 nmol cm⁻²) show thin-layer/surface behaviour in the scan rate range used (0.020-2.0 V s⁻¹), whereas thicker polymers (Γ > ca. 90 nmol cm⁻²) exhibit a changeover from thin-layer to diffusion control regime at a critical scan rate that depends on polymer and film thickness: 0.15-0.20 V s⁻¹ for poly[Cu(salen)], 90 < Γ < 130 nmol cm⁻² and 0.20-0.30 V s⁻¹ for poly[Cu(saltMe)], 170 < Γ < 230 nmol cm⁻².UV-vis and EPR spectroscopies have allowed the characterisation of electronic states in the reduced and oxidised forms. The role of the copper atom during film oxidation was probed by combining UV-vis data with EPR on copolymers of the copper and nickel complexes. Data from both techniques are consistent and indicate that polymerisation and redox switching are associated with ligand-based processes. EPR of Ni-doped Cu polymers provided evidence for the non-involvement of the metal centre in polymer oxidation; like the analogous nickel polymers, copper polymers behave like delocalised π-system (‘conducting’) rather than discrete site (‘redox’) polymers.     

Inorganic-organic hybrid membranes with anhydrous proton conduction prepared from tetramethoxysilane/methyl-trimethoxysilane/trimethylphosphate and 1-ethyl-3-methylimidazolium-bis (trifluoromethanesulfonyl) imide for H2/O2 fuel cells

Anhydrous proton-conducting inorganic-organic hybrid membranes were prepared by sol-gel process with tetramethoxysilane/methyl-trimethoxysilane/trimethylphosphate and 1-ethyl-3-methylimidazolium-bis (trifluoromethanesulfonyl) imide [EMI][TFSI] ionic liquid as precursors. These hybrid membranes were studied with respect to their structural, thermal, proton conductivity, and hydrogen permeability properties. The Fourier transform infrared spectroscopy (FT-IR) and ³¹P, ¹H, and ¹³C nuclear magnetic resonance (NMR) measurements have shown good chemical stability, and complexation of PO(OCH₃)₃ with [EMI][TFSI] ionic liquid in the studied hybrid membranes. Thermal analysis including TG and DTA confirmed that the membranes were thermally stable up to 330 °C. Thermal stability of the hybrid membranes was significantly enhanced by the presence of inorganic SiO₂ framework and high stability of [TFSI] anion. The effect of [EMI][TFSI] ionic liquid addition on the microstructure of the membranes was studied by scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDX) micrographs and no phase separation at the surfaces of the prepared membranes was observed and also homogeneous distribution of all elements was confirmed. Proton conductivity of all the prepared membranes was measured from −20 °C to 150 °C, and high conductivity of 5.4 × 10⁻³ S/cm was obtained for 40 wt% [EMI][TFSI] doped 40TMOS-50MTMOS-10PO(OCH₃)₃ (mol%) hybrid membrane, at 150 °C under anhydrous conditions. The hydrogen permeability was found to decrease from 1.61 × 10⁻¹¹ to 1.39 × 10⁻¹² mol/cm s Pa for 40 wt% [EMI][TFSI] doped hybrid membrane as the temperature increases from 20 °C to 150 °C. For 40 wt% [EMI][TFSI] doped hybrid membrane, membrane electrode assemblies were prepared and a maximum power density value of 0.22 mW/cm² at 0.47 mA/cm² as well as a current density of 0.76 mA/cm² were obtained at 150 °C under non-humidified conditions when utilized in a H₂/O₂ fuel cell.     

Li diffusion in LiNi0.5Mn0.5O2 thin film electrodes prepared by pulsed laser deposition

Kinetic and transport parameters of Li ion during its extraction/insertion into thin film LiNi_0.5Mn_0.5O₂ free of binder and conductive additive were provided in this work. LiNi_0.5Mn_0.5O₂ thin film electrodes were grown on Au substrates by pulsed laser deposition (PLD) and post-annealed. The annealed films exhibit a pure layered phase with a high degree of crystallinity. Surface morphology and thin film thickness were investigated by field emission scanning electron microscopy (FESEM). The charge/discharge behavior and rate capability of the thin film electrodes were investigated on Li/LiNi_0.5Mn_0.5O₂ cells at different current densities. The kinetics of Li diffusion in these thin film electrodes were investigated by cyclic voltammetry (CV) and galvanostatic intermittent titration technique (GITT). CV was measured between 2.5 and 4.5 V at different scan rates from 0.1 to 2 mV/s. The apparent chemical diffusion coefficients of Li in the thin film electrode were calculated to be 3.13 × 10⁻¹³ cm²/s for Li intercalation and 7.44 × 10⁻¹⁴ cm²/s for Li deintercalation. The chemical diffusion coefficients of Li in the thin film electrode were determined to be in the range of 10⁻¹²-10⁻¹⁶ cm²/s at different cell potentials by GITT. It is found that the Li diffusivity is highly dependent on the cell potential.     

New positive-type photosensitive polyimide having sulfo groups

A new positive-working photosensitive polyimide (PSPI) has been developed, which is based on polyimide bearing sulfo groups (PIS) and 1-{1,1-bis[4-(2-diazo-1-(2H)naphthalenone-5-sulfonyloxy)phenyl]ethyl}-4-{1-[4-(2-diazo-1(2H)naphthalenone-5-sulfonyloxy)phenyl]methylethyl}benzene (S-DNQ) as a photosensitive compound. PIS was prepared by ring-opening polyaddition of 1,3-phenylenediamine-4-sulfonicacid (PDAS), 4,4′-oxydianiline (ODA), and 4,4′-hexafluoropropylidenebis(phthalic anhydride) (6FDA), followed by thermal cyclization in m-cresol. PIS containing 30 wt% of S-DNQ showed a sensitivity of 100 mJ cm⁻² and a contrast of 1.7, when it was exposed to 365 nm light followed by developing with 2.38 wt% aqueous tetramethylammonium hydroxide (TMAH) solution at room temperature. A fine positive image featuring 10 μm line and space patterns was observed on the film of the photoresist exposed to 200 mJ cm⁻² of UV-light at 365 nm by the contact mode. The positive image was successfully converted to the polyimide pattern by thermal treatment.     

Thermal conductivity and microstructure of Ti-doped graphite

Ti doped and Si-Ti doped graphites have been developed. The influence of the dopants on the properties and microstructure of doped graphites was analyzed. Test results reveal that Ti doped graphite has excellent bending strength and high thermal conductivity, with highest values reaching 50.2 MPa and 424 W m⁻¹ K⁻¹ for a Ti concentration of 15 wt% in the raw materials. Si added simultaneously with Ti promotes the growth of graphite crystals resulting in an increased thermal conductivity. A kind of Si-Ti doped graphite has been developed with thermal conductivity as high as 494 W m⁻¹ K⁻¹ by optimizing the compositions. Correlation between the content of dopant and the properties and microstructure of doped graphites was studied, and catalytic graphitization mechanism of dopants is also discussed.     

TiO2 nanotubes manufactured by anodization of Ti thin films for on-chip Li-ion 2D microbatteries

The use of self-organized TiO₂ nanotube arrays electrochemically grown onto Si is investigated for the fabrication of an alternative electrode dedicated to on-chip Li-ion 2D microbatteries. Discharge/charge curves and cycling performance are studied in lithium-anode electrochemical test cells for both amorphous and crystalline titania nanotubes. At 5 μA cm⁻² amorphous TiO₂ nanotube layers onto Si deliver a maximum areal capacity of 89 μAh cm⁻² in the first reversible discharge and 56 μAh cm⁻² over 50 cycles. We demonstrate that these nanostructured thin film electrodes showing such electrochemical performances are compatible with IC technology.     

Preparation and electrochemical characterization of the alkaline polymer gel electrolyte polymerized from acrylic acid and KOH solution

An alkaline polymer gel electrolyte (PGE) film was prepared by solution polymerization of acrylate-KOH-H₂O at room temperature, and the preparation conditions were optimized in view of the mechanical properties and ionic conductivity of the film. The PGE film with the optimized composition of 0.02% K₂S₂O₈, 16.75% acrylic acid and 83.23 wt.% 4 mol l⁻¹ KOH solution is transparent, rubber-like and dimensionally stable with improved mechanical properties as compared with gelled electrolyte. The specific conductivity of the film is 0.288 s cm⁻¹ at room temperature and the conductivity values follow the Arrhenius equation with the activation energy of ∼10 kJ mol⁻¹. These data suggest that the ionic conduction proceeds in the same mechanism as in aqueous alkaline solution. Experimental results from the laboratory Zn/Air, Zn/MnO₂ and Ni/Cd cells using the PGE film as electrolyte demonstrate that the PGE film has almost the same chemical and electrochemical stability as aqueous alkaline solution, and shows good performance characteristics for application of alkaline primary and secondary battery systems.