Mobility evolution during tri-axial deformation of a glassy polymer

In this study, the evolution of mobility with deformation in a glassy polymer is compared in cases of dilatationally dominated longitudinal and deviatorically dominated uniaxial deformation. The mobility is evaluated via stress relaxation experiments performed at various points along the stress–strain curve, including pre-yield, yield, and post-yield regions. At T_g−5 °C the mobility decreases with deformation in uniaxial extension, but increases with deformation in tri-axial extension. The τ_eff relaxation time calculated for longitudinal deformation exhibits a dramatically different dependence on the excess volume than the relaxation time obtained in structural relaxation experiments. Finally, the criterion for cavitational failure is proposed based on the thermodynamic stability considerations.     

Post-yield compressed semicrystalline poly(butylene terephthalate): energy storage and release

Post yield deformation of semicrystalline poly(butylene terephthalate) (PBT) is studied by differential scanning calorimetry (DSC) measurements on compressed specimens after unloading. In particular, the effects of strain level, loading-unloading rate, and deformation temperature are analyzed. DSC traces indicate that a remarkable fraction of the mechanical work of deformation (in the range from 25 up to 62%) is stored in the material after unloading. Final strain dependence of stored energy values for specimens deformed up to 40% follows the general S-shaped trend observed for many amorphous and semicrystalline polymers. The ratio of the stored energy to the mechanical work of deformation (ΔU_ST/W) is decreasing as the final deformation level increases. For a given final strain level, the amount of energy stored in specimens deformed under T_g increases as either loading or unloading rates increase: in particular, both ΔU_ST and ΔU_ST/W values are linearly increasing with the logarithm of loading rate. On the other hand, energy storage for specimens deformed at T_g results to be practically independent from the loading rate. Moreover, as the deformation temperature increases from 25 to 100 °C, ΔU_ST values markedly decrease, while the ratio ΔU_ST/W is almost constant around an average value of about 51%.     

Synthesis, characterization and optical properties of fluorinated poly(aryl ether)s containing phthalazinone moieties

A series of novel fluorinated poly(aryl ether)s containing phthalazinone moieties (FPPEs) have been prepared by a modified synthetic procedure for optical waveguide applications. The obtained random copolymers exhibited excellent solubility in polar organic solvents, high glass transition temperatures (T_gs: 185-269 °C), good thermal stabilities (the temperatures of 1% weight loss: 487-510 °C) and good optical properties. By adjusting the feed ratio of the reactants, the refractive indices of TE and TM modes (at 1550 nm) could be well controlled in the range of 1.575-1.498 and 1.552-1.484, respectively. The optical losses of the FPPEs exhibited relatively low values (less than 0.27 dB/cm at 1310 nm). Additionally, the thermo-optic coefficient (dn/dT) values of the FPPEs at 1310 nm and 1550 nm (TE mode) ranged from −0.97 × 10⁻⁴ °C to −1.33 × 10⁻⁴ °C and from −0.96 × 10⁻⁴ °C to −1.29 × 10⁻⁴ °C, respectively.     

The influence of temperature and strain rate on the constitutive and damage responses of polychlorotrifluoroethylene (PCTFE, Kel-F 81)

Polychlorotrifluoroethylene (PCTFE), also known as Kel-F 81, is a semi-crystalline fluoropolymer. Although it has been employed in a wide range of cryogenic components, valve seats, seals, and microelectronics packaging, its mechanical behavior has received limited coverage in the literature. In this work, we present the tensile and compressive constitutive response of PCTFE for a range of temperatures (−85 to 150 °C) and strain rates (1 × 10⁻⁴-2.9 × 10³ s⁻¹). Both large-strain experiments based on flow stress and small-strain dynamic mechanical analysis (DMA) using the elastic modulus exhibit a strong increase in the glass transition temperature, T_g, with increasing strain rate. The quasistatic fracture behavior of PCTFE is presented using J-integral fracture experiments. Finally, a discussion of the implication of the constitutive and damage responses of PCTFE on impact failure modes observed in Taylor impact experiments is presented.     

Synthesis and characterization of two shape-memory polymers containing short aramid hard segments and poly(ε-caprolactone) soft segments

A number of segmented copolymers were synthesized by reacting 4-aminobenzoyl end-functionalized poly(ε-caprolactone)s of M_n 2000, 3000 and 4000 g mol⁻¹ with three aromatic diacid dichlorides in the presence of chlorotrimethylsilane. Polymer purity, molar mass, thermal and mechanical properties were characterized by NMR, MALDI-TOF mass spectrometry, GPC, DSC, and DMTA. Promising shape-memory properties were observed for two polymers that contained comparatively short, semicrystalline poly(ε-caprolactone) soft segments of molecular weight 3000 g mol⁻¹ and either terephthalamide or 2,6-naphthalenedicarboxyamide hard segments. Cast films of these polymers were soft and elastomer-like at room temperature. Loading could be conveniently achieved by cold-drawing at room temperature and strain recovery took place upon heating above the melting temperature of the soft segment (35 °C). Cast films reached uniform deformation properties with strain recovery rates as high as 99% and strain fixity values of 78% after passing through only one or two training cycles.     

Characterisation of activated nanoporous carbon for supercapacitor electrode materials

Commercial nanoporous carbon RP-20 was activated with water vapor in the temperature range from 950 °C to 1150 °C. The XRD analysis was carried out on nanoporous carbon powder samples to investigate the structural changes (graphitisation) in modified carbon that occurred at activation temperatures T ? 1150 °C. The first-order Raman spectra showed the absorption peak at 1582 cm⁻¹ and the disorder (D) peak at 1350 cm⁻¹. The low-temperature N₂ adsorption experiments were performed at −196 °C and a specific surface area up to 2240 m²g⁻¹ for carbon activated at T = 1050 °C was measured. The cell capacitance for two electrode activated nanoporous carbon system advanced up to 60 F g⁻¹ giving the specific capacitance ∼240 F g⁻¹ to one electrode nanoporous carbon ∣1.2 M (C₂H₅)₃CH₃NBF₄ + acetonitrile solution interface. A very wide region of ideal polarisability for two electrode system (∼3.2 V) was achieved. The low frequency limiting specific capacitance very weakly increases with the rise of specific area explained by the mass transfer limitations in the nanoporous carbon electrodes. The electrochemical characteristics obtained show that some of these materials under discussion can be used for compilation of high energy density and power density non-aqueous electrolyte supercapacitors with higher power densities than aqueous supercapacitors.     

Finite strain behavior of poly(ethylene terephthalate) (PET) and poly(ethylene terephthalate)-glycol (PETG)

Uniaxial and plane strain compression experiments are conducted on amorphous poly(ethylene terephthalate) (PET) and poly(ethylene terephthalate)-glycol (PETG) over a wide range of temperatures (25-110 °C) and strain rates (.005-1.0 s⁻¹). The stress-strain behavior of each material is presented and the results for the two materials are found to be remarkably similar over the investigated range of rates, temperatures, and strain levels. Below the glass transition temperature (θ_g=80 °C), the materials exhibit a distinct yield stress, followed by strain softening then moderate strain hardening at moderate strain levels and dramatic strain hardening at large strains. Above the glass transition temperature, the stress-strain curves exhibit the classic trends of a rubbery material during loading, albeit with a strong temperature and time dependence. Instead of a distinct yield stress, the curve transitions gradually, or rolls over, to flow. As in the sub-θ_g range, this is followed by moderate strain hardening and stiffening, and subsequent dramatic hardening. The exhibition of dramatic hardening in PETG, a copolymer of PET which does not undergo strain-induced crystallization, indicates that crystallization may not be the source of the dramatic hardening and stiffening in PET and, instead molecular orientation is the primary hardening and stiffening mechanism in both PET and PETG. Indeed, it is only in cases of deformation which result in highly uniaxial network orientation that the stress-strain behavior of PET differs significantly from that of PETG, suggesting the influence of a meso-ordered structure or crystallization in these instances. During unloading, PETG exhibits extensive elastic recovery, whereas PET exhibits relatively little recovery, suggesting that crystallization occurs (or continues to develop) after active loading ceases and unloading has commenced, locking in much of the deformation in PET.     

Creep behavior of TiCxN1−x-CoTi cermets synthesized by mechanically induced self-sustaining reaction

The plastic flow of TiC_xN_1−x-CoTi cermets has been investigated by uniaxial compression tests carried out in argon atmosphere at temperatures between 1100 and 1200 °C. Two different cermets, with 5 wt.% W or WC content as sintering additives, have been explored to assess the influence of the sintering additives on creep. The microstructural observations of deformed samples and the mechanical results indicate that the hard phase (ceramic grains) controls the plastic deformation. The stress exponent changes from 1 to 2 with increasing strain rate, suggesting a transition in the deformation mechanism from diffusional creep to grain boundary sliding; both with similar activation energy values of about 400 kJ/mol. This value of activation energy agrees with C diffusion in the carbonitride grains as the strain rate controlling mechanism.     

Influence of copolymerisation on fracture behaviour of aliphatic polyketones

High strain rate tensile impact properties of aliphatic polyketone terpolymers were investigated and related to the polymer chain structure. Aliphatic polyketones were used as a model system, by changing the termonomer content and type. Aliphatic polyketone is a perfectly alternating copolymer and the structure was changed with the addition of a few mol% of termonomer: propylene, hexylene and dodecene. Studied were the thermal properties with DSC and DMTA, tensile behaviour, notched tensile impact behaviour, notched Izod properties and the temperature development during deformation. The perfectly alternating copolymer had a melting point of 257 °C, a T_g at 15 °C, a high crystallinity (48%), a high yield stress (77 MPa) and yield strain (31%) but a relatively low fracture strain (85%) and an impact strength (notched Izod) of 13 kJ/m². Increasing the propylene content to 6%, lowered the melting temperature to 224 °C, without changing the T_g. The modulus and yield stress were lowered but the impact strength improved. Increasing the length of the termonomer while keeping the T_m at 224 °C lowered the T_g, the modulus, the yield stress but strongly improved the impact resistance. The longer termonomers, with a lower yield stress, reduced the necking behaviour. The temperature increase in front of the notch was about 85 °C. By adding termonomers to aliphatic ketones, the notched impact behaviour improved significantly at the cost of modulus and yield stress.     

Crosslinking systems and film properties for surfactant-free latexes based on anhydride-containing polymers

In this paper, we report novel crosslinking systems for surfactant-free artificial latexes based on anhydride-containing polymers. Surfactant-free latexes with average particle diameters of about 150 nm and a ζ-potential of −70 mV have been successfully obtained from anhydride-containing polymers with various T_gs and polarities, including poly(octadecene-alt-maleic anhydride) (POMA) and maleinized polybutadiene (PBDMA). When adipic dihydrazide (ADH), a water-soluble crosslinker, was added to these latexes, no differences in particle size or ζ-potential were found; the presence of ADH did not affect the latex stability. In contrast, when 1,6-diaminohexane (DAH) was added to these latexes, it was found to interact with the polymer particles, indicated by a decrease in absolute ζ-potential for the latex particles and even gelation in the case of POMA. From ¹H NMR and LC-MS studies, it has been shown that no free DAH was present after being added to the latex, while free, unreacted ADH was present in aqueous phase upon its addition to the latex. Kinetic studies revealed that irreversible imide formation between anhydride and ADH took place at temperatures of 90 °C and above. In comparison, DAH only formed imides with the copolymers at significantly higher curing temperatures, i.e. >130 °C. Furthermore, the film formation of these latexes was studied; for the different copolymer latexes, curing at temperatures above the T_g of the respective copolymers led to homogeneous film formation. These systems based on surfactant-free latexes crosslinked with ADH have displayed promising properties for future coating applications.     

Metal-organic framework (MOF) as a template for syntheses of nanoporous carbons as electrode materials for supercapacitor

Five nanoporous carbons (NPCs) were prepared by polymerizing and then carbonizing carbon precursor of furfuryl alcohol accommodated in a porous metal-organic framework (MOF-5, [Zn₄O(bdc)₃], bdc = 1,4-benzenedicarboxylate) template. The Brunauer-Emmett-Teller (BET) surface areas for five NPC samples obtained by carbonizing at the temperatures from 530 to 1000 °C fall into the range from 1140 to 3040 m² g⁻¹ and the dependence of BET surface areas on carbonization temperatures shows a “V” shape. All the five NPC samples have a pore size distribution centered at about 3.9 nm. As electrode materials for supercapacitor, the NPC samples obtained at the temperatures higher than 600 °C display the ideal capacitor behaviors and give rise to almost constant specific capacitance (above 100 F g⁻¹ at 5 mV s⁻¹) at various sweep rates, which is associated with their mesoporous characteristics. However, the NPC sample with the highest BET surface area (3040 m² g⁻¹) obtained by carbonizing at 530 °C gives a unusually low capacitance (12 F g⁻¹ at 5 mV s⁻¹), which may be attributed to the poor conductivity of the carbon material due to the low carbonization temperature.     

Thermal and radio-oxidation of epoxy coatings

Degradation induced by thermal (50–110 °C) and radio-oxidation of low T_g epoxy-amine networks has been studied. It has been found that oxidation leads mainly to amide groups formation at the vicinity of tertiary amines whatever ageing conditions (thermal or radio-oxidation at 200 Gy h⁻¹). In addition, some species as acids, peracids or formates have been revealed indicating a chain scission process. Physical modifications as T_g decrease and soluble fraction increase due to chain scission process, have been correlated with chemical modifications.     

Energy and power performance of electrochemical double-layer capacitors based on molybdenum carbide derived carbon

Cyclic voltammetry, constant current charge/discharge, and electrochemical impedance spectroscopy have been applied to establish the electrochemical characteristics for electric double-layer capacitor (EDLC) consisting of the 1 M (C₂H₅)₃CH₃NBF₄ electrolyte in acetonitrile and micro/mesoporous carbon electrodes prepared from Mo₂C, noted as C(Mo₂C). The N₂ sorption (total BET specific surface area (S_BET ≤ 1855 m² g⁻¹), micropore area (S_micro ≤ 1823 m² g⁻¹), total pore volume (V_tot ≤ 1.399 m³ g⁻¹) and pore size distribution (average NLDFT pore width d_NLDFT ≥ 0.89 nm) values obtained have been correlated with the electrochemical characteristics for EDLCs (region of ideal polarizability (ΔV = 3.0 V), characteristic time constant (τ_R = 1.05 s), gravimetric capacitance (C_m ≤ 143 F g⁻¹)) dependent strongly on the C(Mo₂C) synthesis temperature. High gravimetric energy (35 Wh kg⁻¹) and gravimetric power (237 kW kg⁻¹) values, normalised to the total active mass of both C(Mo₂C) electrodes, synthesised at T_synt = 800 °C, have been demonstrated at cell voltage 3.0 V and T = 20 °C.     

Preparation, characterization and mechanical properties of epoxidized soybean oil/clay nanocomposites

New epoxidized soybean oil (ESO)/clay nanocomposites have been prepared with triethylenetetramine (TETA) as a curing agent. The dispersion of the clay layers is investigated by X-ray diffraction (XRD) and transmission electron microscopy (TEM). XRD and TEM data reveal the intercalated structure of ESO/clay nanocomposites has been developed. The thermogravimetric analysis exhibits that the ESO/clay nanocomposites are thermally stable at temperatures lower than 180 °C, with the maximum weight loss rate after 325 °C. The glass transition temperature, T_g, about 7.5 °C measured by differential scanning calorimetry (DSC) and T_g about 20 °C measured by dynamic mechanical study have been obtained. The difference in the T_g between DSC and dynamic measurements may be caused by different heating rate. The nanocomposites with 5-10 wt% clay content possess storage modulus ranging from 2.0×10⁶ to 2.70×10⁶ Pa at 30 °C. The Young's modulus (E) of these materials varies from 1.20 to 3.64 MPa with clay content ranging from 0 to 10 wt%. The ratio of epoxy (ESO) to hydrogen (amino group of TETA) greatly affects dynamic and tensile mechanical properties. At higher amount of TETA, the nanocomposites exhibit stronger tensile and dynamic properties.     

Microstructure of free volume in SMA copolymers I. Free volume from Simha-Somcynsky analysis of PVT experiments

The structure of the free volume and its temperature dependence between 25 and 200 °C of copolymers of styrene with maleic anhydride, SMA (0-35 mol% MA), is studied by pressure-volume-temperature (PVT) experiments and positron annihilation lifetime spectroscopy (PALS). In this first part of the work, PVT data are reported which were analysed with the Simha-Somcynsky equation of state to estimate the volume fraction of holes, h, which constitute the excess free volume. The temperature and pressure dependence of the specific volume V, the specific occupied and free volume, V_occ=(1−h)V and V_f=hV, and the corresponding isobaric expansivities and isothermal compressibilities for both the rubbery and glassy state are estimated. We obtained the unexpected results that (i) the occupied volume changes its coefficient of thermal expansion at T_g from α_occ,g≈0.5α_g≈1×10⁻⁴ K⁻¹ below T_g to almost zero (≈0.2×10⁻⁴ K⁻¹) above T_g and (ii) the isothermal compressibility of the occupied volume at zero pressure below T_g is rather high, κ_occ≈2.5×10⁻⁴ MPa⁻¹, and decreases only slightly at T_g to about 2×10⁻⁴ MPa⁻¹ above T_g. The variation of total, occupied, and free volume parameters with the composition of the SMA copolymers is discussed.     

Lamella reorientation in thin films of a symmetric poly(l-lactic acid)-block-polystyrene upon crystallization at different temperatures

The thin films of a symmetric crystalline-coil diblock copolymer of poly(l-lactic acid) and polystyrene (PLLA-b-PS) formed lamellae parallel to the substrate surface in melt. When annealed at temperatures well above the glass transition temperature of PLLA block (T_g^PLLA), the PLLA chains started to crystallize, leading to reorientation of lamellae. Such reorientation behavior exhibited dependence on the correlation between the crystallization temperature (T_c), the glass transition temperature of PS (T_g^PS), the peak melting point of PLLA crystals (T_m^PLLA), and the end melting point of PLLA crystals (T_m,end^PLLA). When annealed at (T_c=) 80 °C (T_c < T_g^PS < T_ODT, order-disorder transition temperature), 123 °C (T_g^PS < T_c < T_m^PLLA < T_ODT), 165 °C (T_g^PS < T_m^PLLA < T_c < T_m,end^PLLA < T_ODT), the parallel lamellae became perpendicular to the substrate surface, exclusively starting at the edge of surface relief patterns. Meanwhile, the corresponding lamellar spacing was significantly enhanced. The PLLA crystallization between PS layers was hypothesized to account for the lamella reorientation during annealing. The crystallization, chain conformation, and possible chain folding mechanisms were discussed, based on detailed analysis of the lamellar structure before and after crystallization.     

Investigation of the intra-particle sintering kinetics of a mainly agglomerated alumina powder by using surface area reduction

An alumina precursor was prepared by the aluminium sulphate (0.20 M) and excess urea reaction in boiling aqueous solution. The precursor was calcined at 900 °C for 2 h and then δ-Al₂O₃ powder having volumetric agglomeration degree of 80% was obtained. Cylindrical compacts having diameter of 14 mm were prepared under 32 MPa by axial pressing using oleic acid as binder. Each compact was fired isothermally at various temperatures between 950 and 1400 °C. The firing time was changed from zero to 2 h. The fired compacts were examined by scanning electron microscopy (SEM) and nitrogen adsorption techniques. The specific surface areas (S/m² g^− 1) of the samples were calculated using the Brunauer, Emmett, and Teller (BET) procedure. The rate constant (k) and mechanism-characteristic parameter (n) were obtained for different temperatures between 950 °C and 1150 °C from the application of the neck-growth sintering rate (NGRM) model on the surface area reduction data. An Arrhenius equation and the parameter n for the sintering were found in the forms of k = (7.648 × 10⁶ h^− 1) exp (− 186,234 J mol^− 1 / RT) and n = 4.0 × 10^− 7 T³-1.7 × 10^− 3 T² + 2.3 T − 1030.8 respectively. The parameter n changes in the interval 0.61 <  n < 1.34 with rising temperature having maximum at about 1025 °C. Based on the SEM images and NGRM data, the intra-particle sintering was discussed.     

Fracture of polybutylene terephthalate (PBT) film

Combined effects of thickness and temperature on essential work of fracture (EWF) of polybutylene terephthalate (PBT) film were studied using single edge notched tension (SENT) and double edge notched tension specimens. It is found that specific essential work of fracture (w_e) for PBT is independent of temperature below T_g (≈80 °C), but decreases above T_g. Between temperatures 25 and 100 °C, w_e was independent of film thickness in the range 0.125-0.375 mm. The specific non-essential work of fracture (βw_p) was temperature and thickness dependent, being greater for the SENT type specimens. Specimen orientation had no influence on w_e but strongly affected βw_p. It was found that βw_p is greater for cracks propagating normal to the extrusion direction as compared to the parallel direction.     

Crystallization, structure and properties of plasticized poly(l-lactide)

Poly(l-lactide) (PLA) was plasticized with poly(ethylene glycol)s having M_w of 400 and 600 g/mol. In addition to poly(ethyne glycol)s with hydroxyl end groups, monomethyl ethers of poly(ethylene glycol) having M_w of 550 and 750 g/mol, with chains terminated with hydroxyl groups and methyl groups, were used. The effect of different end groups on the plasticization of both amorphous and semicrystalline PLA was studied. The crystallization, structure, thermal and tensile properties of PLA and PLA with 5 and 10 wt% of plasticizers were explored. No marked effect induced by different end groups of plasticizers was found. All the plasticizers used decreased T_g and increased the ability of PLA to cold crystallization. While an amorphous plasticized PLA could be deformed to about 550%, a semicrystalline PLA with the same total plasticizer content exhibited nonuniform plasticization of the amorphous phase and less ability to the plastic deformation. Nevertheless, a 20% elongation at break was achieved for a semicrystalline PLA with 10 wt% of the plasticizer. The plastic deformation of both neat and plasticized PLA was associated with crazing.     

Synthesis and aqueous solution characterization of amphiphilic diblock copolymers containing carbazole

A series of near-monodisperse diblock copolymers of 2-(N-carbazolyl)ethyl methacrylate and 2-(dimethylamino)ethyl methacrylate (DMAEMA) of relatively low molecular weights (2600-24,000 g mol⁻¹) were synthesized by group transfer polymerization using tetrahydrofuran (THF) as a solvent. The molecular weight distributions and compositions of all the copolymers were obtained using gel permeation chromatography (GPC) in THF and proton nuclear magnetic resonance (¹H NMR) spectroscopy, respectively. Differential scanning calorimetry and thermal gravimetric analysis provided low glass transition temperatures (T_gs) of about 60 °C and decomposition temperatures between 320 and 450 °C for the copolymers, respectively. The three copolymers with the highest DMAEMA content were water-soluble below pH 7. Aqueous GPC at pH 3 showed that the water-soluble block copolymers formed micelles with apparent number average molecular weights above 100,000 g mol⁻¹.