Kinetics and Mechanism of Hot Corrosion of γ-Y2Si2O7 in Thin-Film Na2SO4 Molten Salt

γ-Y₂Si₂O₇ is a promising candidate material both for high-temperature structural applications and as an environmental/thermal barrier coating material due to its unique properties such as high melting point, machinability, thermal stability, low linear thermal expansion coefficient (3.9 × 10⁻⁶/K, 200°–1300°C), and low thermal conductivity (<3.0 W/m·K above 300°C). The hot corrosion behavior of γ-Y₂Si₂O₇ in thin-film molten Na₂SO₄ at 850°–1000°C for 20 h in flowing air was investigated using a thermogravimetric analyzer (TGA) and a mass spectrometer (MS). γ-Y₂Si₂O₇ exhibited good resistance against Na₂SO₄ molten salt. The kinetic curves were well fitted by a paralinear equation: the linear part was caused by the evaporation of Na₂SO₄ and the parabolic part came from gas products evolved from the hotcorrosion reaction. A thin silica film formed under the corrosion scale was the key factor for retarding the hot corrosion. The apparent activation energy for the corrosion of γ-Y₂Si₂O₇ in Na₂SO₄ molten salt with flowing air was evaluated to be 255 kJ/mol.     

Tailoring Texture of γ-Y2Si2O7 by Strong Magnetic Field Alignment and Two-Step Sintering

In this study, a well-dispersed γ-Y₂Si₂O₇ ethanol-based suspension with 30 vol% solid loading was prepared by adding 1 dwb% polyethylene imine dispersant, which allows feeble magnetic γ-Y₂Si₂O₇ particles with anisotropic magnetic susceptibility to rotate in a 12 T strong magnetic field during slip casting, resulting in the development of a strong     texture in green bodies. Pressureless sintering gives rise to more pronounced grain growth in the textured sample than in the untextured sample prepared without the magnetic field due to the rapid migration of the grain boundaries of the well-oriented grains, which was revealed by constant-heating-rate sintering kinetics. It was found that the use of two-step sintering is very efficient not only for inhibiting the grain growth but also for enhancing the     texture. This implies that controlled grain growth is crucial for enhancing texture development in γ-Y₂Si₂O₇.     

Microstructural Evolution in Near-Eutectic Yttrium Silicate Compositions Fabricated from a Bulk Melt and as an Intergranular Phase in Silicon Nitride

Near-eutectic composition Y₂O₃─SiO₂ melts were formed as bulk samples or as an intergranular phase in Si₃N₄. Upon cooling to room temperature the bulk material partially crystallized to γ-Y₂-Si₂O₇ whereas the intergranular phase was glass. On heat-treating at 1500°C the bulk material transformed to γ-Y₂Si₂O₇ whereas the intergranular glass crystallized first to γ-Y₂Si₂O₇ and then to β-Y₂Si₂O₇. Possible reasons for the different behavior are discussed.     

Silica Glass Segregation in 3 wt% LiF-Doped Hot-Pressed Y2Si2O7

Hot-pressed yttrium disilicate ceramics have been characterized using analytical transmission electron microscopy (TEM). The microstructure consists of large grains of the γ phase of stoichiometric γ-Y₂Si₂O₇ containing rounded glassy Y-doped SiO₂ inclusions; excess glassy SiO₂-rich material is also found at the grain boundaries. Two main reasons are found for the inhomogeneity: a slight SiO₂ excess is inferred from the composition measurements, and the LiF flux used in hot pressing would also promote glass formation. Improved high-temperature mechanical properties would only be possible if residual glass formation was minimized, strategies for doing so are discussed, and the importance of analytical TEM for studying such submicron scale inhomogeneity is underlined.     

Hydrolysis and Dispersion Properties of Aqueous Y2Si2O7 Suspensions

The dispersion of aqueous γ-Y₂Si₂O₇ suspensions, which contain only one component but have a complex ion environment, was studied by the introduction of two different polymer dispersants, polyethylenimine (PEI) and polyacrylic acid (PAA). The suspension without any dispersant remains stable in the pH range of 9–11.5 because of electrostatic repulsion, while it is flocculated upon stirring due to the readsorption of hydrolyzed ions on the colloid surface. However, suspensions with 1 dwb% PEI exhibit greater stability in the pH range of 4–11.5. The addition of PEI shifts the isoelectric point (IEP) of the suspensions from pH 5.8 to 10.8. Near the IEP (pH_IEP=10.8), the stability of the suspensions with PEI is dominated by the steric effect. When the pH is decreased to acid direction, the stabilization mechanism is changed from steric hindrance to an electrosteric effect little by little. PAA also has the effect of reducing the hydrolysis speed via a "buffer effect" in the basic pH range, but the lack of adsorption between the highly ionized anionic polymer molecules and the negative colloid particle surfaces shows no positive effect on hydrolysis of colloids and on the stabilization of Y₂Si₂O₇ suspensions.     

Microstructural Changes in β-Silicon Nitride Grains upon Crystallizing the Grain-Boundary Glass

Crystallizing the grain-boundary glass of a liquid-phase-sintered Si₃N₄ ceramic for 2 h or less at 1500° led to formation of δ-Y₂Si₂O₇. After 5 h at 1500°, the δ-Y₂Si₂O₇ had transformed to β-Y₂Si₂O₇ with a concurrent dramatic increase in dislocation density within β-Si₃N₄ grains. Reasons for the increased dislocation density are discussed. Annealing for 20 h at 1500° reduced dislocation densities to the levels found in as-sintered material.     

The System Si3N4-SiO2-Y2O3

Subsolidus phase relations were established in the system Si₃N₄-SiO₂-Y₂O₃. Four ternary compounds were confirmed, with compositions of Y₄Si₂O₇N₂, Y₂Si₃O₃N₄, YSiO₂N, and Y₁₀(SiO₄)₆N₂. The eutectic in the triangle Si₃N₄-Y₂Si₂O₇-Y₁₀(SiO₄)₆N₂ melts at 1500°C and that in the triangle Si₂N₂O-SiO₂-Y₂Si₂O₇ at 1550°C. The eutectic temperature of the Si₃N₄-Y₂Si₂O₇ join was ∼ 1520°C.     

Phase Relations in the System Al2O3─Ce2Si2O7 in the Temperature Range 900° to 1925°C in Inert Atmosphere

Equilibrium relationships in the system Al₂O₃-Ce₂Si₂O₇ in inert atmosphere have been investigated in the temperature range 900° to 1925°C. A simple eutectic reaction was found at 1375°C and 51 mol% Ce₂Si₂O₇. A high-low polymorphic transformation in Ce₂Si₂O₇ was observed at 1274°C. New XRD patterns are suggested for both polymorphs of cerium pyrosilicate. The melting point of Ce₂Si₂O₇ was found to be 1788°C. A value for ΔH°_m,Ce2Si2O7 of 36.81 kJ/mol was calculated from the initial slope of the experimentally determined liquidus in equilibrium with the pyrosilicate phase.     

Phase Equilibria in the System Na2SiO3-Li2SiO3-SiO2

Ternary phase relations have been studied and several modifications made to Kracek's phase equilibrium diagram. These include location of the primary phase fields of Na₆Si₈O₁₉ and Li₂Si₂O₅. Metastable phases and polymorphs were often encountered, notably a primary phase, δ-Na₂Si₂O₅, and a new polymorph of Li₂Si₂O₅.     

Reaction-Formed Porous Yb4Si2N2O7 Materials with Uniform Open-Cell Network Structure

A novel porous Yb₄Si₂O₇N₂ material with uniform open-cell network structure was fabricated from the reaction between Si₃N₄, Yb₂O₃, and SiO₂. The formation of Yb₄Si₂O₇N₂ during heating was studied using X-ray diffractometry. The porous structure was characterized using scanning electron microscopy and mercury porosimeter. It is shown that the formation of Yb₄Si₂O₇N₂ phase starts at ∼1150°C and completes at 1350°C for 4 h, accompanied by the development of open-cell network structure. The necks between Yb₄Si₂O₇N₂ particles become much thicker with increasing temperature because of the coarsening of Yb₄Si₂O₇N₂ particles, thus leading to a uniform three-dimensional network structure. Furthermore, the pore size can be well controlled by adjusting reacting temperature and altering atmosphere.     

Synthesis of Celsian (BaAl2Si2O8) from Solid Ba-Al-Al2O3-SiO2 Precursors: I, XRD and SEM/EDX Analyses of Phase Evolution

An intimate Ba-Al-Al₂O₃-SiO₂ powder mixture, produced by high-energy milling, was pressed to 3 mm thick cylinders (10 mm diameter) and hexagonal plates (6 mm edge-to-edge width). Heat treatments conducted from 300° to 1650°C in pure oxygen or air were used to transform these solid-metal/oxide precursors into BaAl₂Si₂O₈. Barium oxidation was completed, and a binary silicate compound, Ba₂SiO₄, had formed within 24 h at 300°C. After 72 h at 650°C, aluminum oxidation was completed, and an appreciable amount of BaAl₂O₄ had formed. Diffraction peaks consistent with hexagonal BaAl₂Si₂O₈, BaAl₂O₄, β-BaSiO₃, and possibly β-BaSi₂O₅ were detected after 24 h at 900°C. Diffraction peaks for BaAl₂O₄ and BaAl₂Si₂O₈ were observed after 35 h at 1200°C, although SEM analyses also revealed fine silicate particles. Further reaction of this silicate with BaAl₂O₄ at 1350° to 1650°C yielded a mixture of hexagonal and monoclinic BaAl₂Si₂O₈. The observed reaction path was compared to prior work with other inorganic precursors to BaAl₂Si₂O₈.     

Improvement in Mechanical Properties of Powder-Processed MoSi2 by the Addition of Sc2O3 and Y2O3

Additions of 1-20 mol% Sc₂O₃ or Y₂O₃ to MoSi₂ eliminate glassy SiO₂, which improves mechanical properties at both ambient and high temperatures. In particular, only 1 mol% ScO₃ additions dramatically enhance three-point bending strength from 521 to 1081 MPa. Vickers hardness, Young's modulus, fracture toughness, and high-temperature strength are also improved by this low level of additive. The improvement of mechanical properties is attributed to the formation of crystalline silicates: Sc₂Si₂O₇, Y₂Si₂O₇, Y₂SiO₅, and Y₄Si₃O₁₂, which are analyzed by XRD, SEM-EDS, and TEM-EDS methods.     

Phase Relationships in the Si3N4–SiO2–Lu2O3 System

Phase relationships in the Si₃N₄–SiO₂–Lu₂O₃ system were investigated at 1850°C in 1 MPa N₂. Only J-phase, Lu₄Si₂O₇N₂ (monoclinic, space group P 2₁/ c , a = 0.74235(8) nm, b = 1.02649(10) nm, c = 1.06595(12) nm, and β= 109.793(6)°) exists as a lutetium silicon oxynitride phase in the Si₃N₄–SiO₂–Lu₂O₃ system. The Si₃N₄/Lu₂O₃ ratio is 1, corresponding to the M-phase composition, resulted in a mixture of Lu–J-phase, β-Si₃N₄, and a new phase of Lu₃Si₅ON₉, having orthorhombic symmetry, space group Pbcm (No. 57), with a = 0.49361(5) nm, b = 1.60622(16) nm, and c = 1.05143(11) nm. The new phase is best represented in the new Si₃N₄–LuN–Lu₂O₃ system. The phase diagram suggests that Lu₄Si₂O₇N₂ is an excellent grain-boundary phase of silicon nitride ceramics for high-temperature applications.     

Effects of Amorphous and Crystalline SiO2 Additives on γ-Al2O3-to-alpha-Al2O3 Phase Transitions

This paper focused on the effects of various phases of SiO₂ additives on the γ-Al₂O₃-to-α-Al₂O₃ phase transition. In the differential thermal analysis, the exothermic peak temperature that corresponded to the theta-to-α phase transition was elevated by adding amorphous SiO₂, such as fumed silica and silica gel obtained from the hydrolysis of tetraethyl orthosilicate. In contrast, the peak temperature was reduced by adding crystalline SiO₂, such as quartz and cristobalite. Amorphous SiO₂ was considered to retard the γ-to-α phase transition by preventing γ-Al₂O₃ particles from coming into contact and suppressing heterogeneous nucleation on the γ-Al₂O₃ surface. On the other hand, crystalline SiO₂ accelerated the α-Al₂O₃ transition; thus, this SiO₂ may be considered to act as heterogeneous nucleation sites. The structural difference among the various SiO₂ additives, especially amorphous and crystalline phases, largely influenced the temperature of γ-Al₂O₃-to-α-Al₂O₃ phase transition.     

Effect of Li2CO3 Addition on the Sintering Temperature and Microwave Dielectric Properties of Mg2V2O7 Ceramics

Li₂CO₃ was added to Mg₂V₂O₇ ceramics in order to reduce the sintering temperature to below 900°C. At temperatures below 900°C, a liquid phase was formed during sintering, which assisted the densification of the specimens. The addition of Li₂CO₃ changed the crystal structure of Mg₂V₂O₇ ceramics from triclinic to monoclinic. The 6.0 mol% Li₂CO₃-added Mg₂V₂O₇ ceramic was well sintered at 800°C with a high density and good microwave dielectric properties of ɛ _r=8.2, Q × f =70 621 GHz, and τ_f=−35.2 ppm/°C. Silver did not react with the 6.0 mol% Li₂CO₃-added Mg₂V₂O₇ ceramic at 800°C. Therefore, this ceramic is a good candidate material in low-temperature co-fired ceramic multilayer devices.     

Phase Equilibria and Crystallization of Melts in the System Na2O-BaO-SiO2

Phase-equilibrium studies of the liquidus surface of the Na₂O-BaO-SiO₂ system are presented. The system contains 5 ternary compounds, Na₂Ba₄Si₁₀O₂₅, Na₂Ba₄Si₂O₆, Na₂Ba₂Si₂O₇, X (probably Na₂Ba₁₈Si₂₈O₇₅), and Y (probably Na₂Ba₄₅Si₇₃O₁₉₂), all of which melt incongruently. Twenty-three liquidus invariant points, including 13 peritectics, 4 eutectics, and 6 thermal maxima, were located. Metastable crystallization reactions are commonly encountered, and some of the metastable equilibria are described.     

Phase Relations and Stability Studies in the Si3N4-SiO2-Y2O3 Pseudoternary System

Composite powders were hot-pressed to determine the phase relations in the Si₃N₄-SiO₂-Y₂O₃ pseudoternary system. Four quaternary compounds, Si₃Y₂O₃N₄, YSiO₂N, Y₁₀Si₇O₂₃N₄, and Y₄Si₂O₇N₂, were identified. Studies of polyphase and single-phase materials in this system showed that these 4 compounds are unstable under oxidizing conditions. Materials within the Si₃N₄-Si₂N₂O-Y₂Si₂O₇ compatibility triangle precluded the unstable compounds, and are extremely resistant to oxidation.     

Phase Equilibria in High-Alumina Part of the System CaO–MgO–Al2O3–SiO2

Results are presented of a study of phase equilibria among crystalline and liquid phases in the quaternary system CaO–MgO-Al₂O₃–SiO₂ at Al₂O₃ contents greater than 35%. Equilibrium diagrams shown are for the five triangular joins CaAl₂Si₂O₃-Ca₂Al₂SiO₇-MgAl₂O₄, Ca₂Al₂SiO₇-MgAl₂O₄-Al₂O₃, CaAl₂Si₂O₈-MgO-Al₂O₃, CaAl₂Si₂O₈-Mg₂SiO₄-MgAl₂O₄, and CaAl₂Si₂O₈-MgO-Mg₂SiO₄. The composition and nature of the four quaternary peritectic points and the relationships of univariant lines and primary phase volumes are discussed.     

Studies in the System Li2O–Al2O3–Fe2O3-H2O

Subsolidus equilibrium relations in a portion of the system Li2O-Fe₂O₃-Al₂O3 in the temperature range 500° to 1400°C. have been determined near po₂ = 0.21. Of particular interest in this system is the LiFe₅O₈-LiAl₅O₈ join, which shows complete solid solution above 1180°C. Below this temperature the solid solution exsolves into two spinel phases. At 600°C. approximately 15 mole % of each compound is soluble in the other. The high-temperature solid solution and the low-temperature exsolution dome extend into the ternary system from the 1:5 join. There is no appreciable crystalline solubility of LiFeO₂ or of α-Fe₂O₃ in LiFe₅O₈. An attempt to confirm HFe₅O₈ as the correct formulation of the magnetic ferric oxide "γ-Fe₂O₃" was inconclusive, but in the absence of positive evidence, the retention of γ-Fe₂O₃ is recommended. All the metallic oxides of the Group IV elements increase the temperature of the monotropic conversion of -γ-Fe₂O₃ to α-Fe₂O₃. Silica and thoria have a greater effect on this conversion than does titania or zirconia.     

Phase Equilibrium Studies in the System CaO-Cr2O3-SiO2

Results are presented of a study in air of mixtures in the system CaO-Cr₂O₃-SiO₂. The phase equilibrium diagram shows relations at liquidus temperatures for all but the high-lime part of the system. In this omitted part chromium in the mixtures oxidizes in air to higher valence forms. The compound Ca₃Cr₂Si₃O₁₂ (uvarovite) occurs at subsolidus temperatures, decomposing at 1370°C. to α-CaSiO₃ and Cr₂O₃. The inhibiting action of chromium oxide on the inversion of high-temperature forms of Ca₂SiO₄ to the low-temperature γ-Ca₂SiO₄ is discussed in the light of new data. Evidence is presented for the existence of a pentavalent chromium compound, Ca₃(CrO₄)₂, having solid-solution relations with Ca₃SiO₄.