载气蒸发的传热性能

本研究以空气-水为物系,在减压条件下,于Φ22×3.5 mm,长1500 mm的垂直管中进行了载气蒸发传热实验。研究了平均传热膜系数和局部传热膜系数随液速、载气流量及操作温度的变化规律,并分析了载气强化沸腾传热的机理。在此基础上获得了载气蒸发传热膜系数的关联式。     

循环浆态床气液传质系数的研究

以空气-水-玻璃微珠和空气-石蜡油-玻璃微珠两种三相系统为研究对象,在常温常压下分别考察了液体介质的粘度等物性因素,表观气速、固含率、液体循环量等操作因素,气体分布器、分隔板等结构因素对循环浆态床反应器气液传质特性的影响.实验结果表明,气液传质系数随表观气速的增加而增加,随液体粘度和固含率的增大而减小,当表观气速和固含率增加到一定程度后,传质系数趋于稳定;低气速下,玻璃烧结板的传质效果较好,而较高气速时,多孔板和新型锐孔分布器的传质效果较好;分隔板能显著增大气液传质系数.对多孔板分布器实验数据进行了拟合,得出气液传质系数的经验关联式,关联式计算值与实验结果吻合良好.     

载气蒸发传热及其流型的研究

载气蒸发是在沸腾的液体中引入一种惰性气体,成为液体的汽化中心,使液体的汽化在气—液界面上进行。载气的引入,强化了传热,降低了壁面液体的过热度。本文对空气一水物系,在φ32×3长为1300mm的垂直管中,进行了载气蒸发过程的传热研究和流型观测,并对载气蒸发传热机理进行了分析。     

第十讲 载气蒸发传热的研究

本文提出一种新的蒸发法—载气蒸发法,以一种惰性气体为载气,用水和低亚硫酸钠、丙烯酰胺水溶液等物料,研究了载气量、总传热温差和溶液浓度等对载气蒸发传热系数的影响。在此基础上进一步推算并研究了它们对沸腾传热膜系数的影响。     

两相流载气蒸发研究和传热数据关联

两相流载气蒸发是在蒸发器的垂直加热管中引入一种惰性气体,使液体的蒸发在气液两相界面上进行的过程.本文研究了载气蒸发的流型区域和传热规律,对载气蒸发的特性进行了机理分析,并以叠加模型关联了实验数据,获得了准数方程式.     

高长径比三相内环流反应器中细颗粒相含率和循环液速的分布研究

在高径比为22的三相内环流反应器中,在常温常压下以空气-水-石英砂为物系,研究了在不同粒径下上升区固含率、下降区固含率和上升区循环液速随表观气速的变化规律和不同粒径下轴向固含率的分布情况,以及在固体体积分数不同的条件下,平均气含率和上升区气含率随表观气速的变化情况。结果表明:当粒径(ds)≤0.3 mm时,上升区固含率随表观气速的增加呈平缓变化趋势,下降区固含率随表观气速的增加而增加;当0.3 mm相似文献   

垂直管内降膜载气蒸发的研究

在蒸发的降液膜表面引入惰性载气,可以有效地强化降膜蒸发传热。研究了液体流量、载气流量、壁面热负荷及料液物性等对降膜载气蒸发传热的影响。建立了数学模型,并进行了数值求解。实验结果表明,采用降膜载气蒸发,可提高传热膜系数,降低壁面过热度。还将模型计算结果与实验结果进行了比较。     

超声内环流气升式反应器传质性能的研究

研究了超声内环流气升式反应器中空气-水-离子交换树脂体系的气液传质与液固传质性能.分别采用电极动态法和离子交换树脂法实验测定了气液传质和液固传质系数.重点考察了表观气速、超声电功率对于气液传质系数以及液固传质系数的影响.实验表明,内环流气升式反应器中表观气速对于气液传质性能影响较大,而超声作用对气液传质影响不大.该反应器中液固传质系数随表观气速的增加而增大;无超声作用情况下,当表观气速达到一定程度时,液固传质系数保持一恒定值.超声作用时,气速增加到4 cm·s-1左右,传质系数达到最大值,随后液固传质系数随着表观气速的增加而逐渐减小,传质系数仍然大于无超声作用时的值.超声对液固传质有较强的促进作用,电功率在150 W左右时,超声对液固传质的促进作用最佳,是不加超声作用时传质系数的两倍左右;但随着电功率的进一步增大,液固传质系数呈现下降趋势.     

内冷式刮膜蒸发器粘性流体的传热与蒸发探讨

本文以粘性流体甘油为物料,在内冷式刮膜薄膜蒸发器中进行加热蒸发实验,分析和探讨了内冷式刮膜薄膜蒸发的传热阻力和工艺条件如操作压力、刮板转速和进料流量等因素的影响。研究发现,粘性流体薄膜蒸发时的传热阻力主要在液膜侧;液膜传热系数随刮板转速和流量的增大而增大,随压力的降低而增大;单位时间的蒸发量随刮板转速的增大而增大,随压力和流量的增大而减少。     

刮膜式分子蒸馏器内传质的数值模拟

在刮膜式分子蒸馏器中,研究液膜内传质传热特性对改进蒸馏器内流场结构和优化操作参数具有重要意义。今采用计算流体力学(Computational Fluid Dynamics,CFD)软件,建立刮膜式分子蒸馏器三维模型,研究了液膜表面温度、浓度、蒸发速率沿三维方向变化,并探究了进料量和加热温度对传质传热特性的影响。结果表明:头波前液膜表面温度随着远离头波沿周向和径向逐渐减小,沿轴向逐渐增加,头波处、壁面附近和液膜表面处温度梯度较大;壁面附近处易挥发组分浓度几乎不变,但沿三维均呈减小趋势;蒸发速率沿三维的变化和温度呈相同的趋势;进料量越小,加热温度越高,液膜表面温度、易挥发组分蒸发速率和液相总传质系数越大,易挥发组分浓度减少的也越快,有利于传质。但较高的加热温度会增加生产成本,且易使物料分解,故应选择合适的加热温度。     

Insect antifeedant properties of anthranoids from the genusVismia

Vismiones and ferruginins, representatives of a new class of lypophilic anthranoids from the genusVismia were found to inhibit feeding in larvae of species ofSpodoptera, Heliothis, and inLocusta migratoria.     

Direct observation of freeze-thaw instability of latex coatings via high pressure freezing and cryogenic SEM

Despite its industrial importance, the subject of freeze-thaw (F/T) stability of latex coatings has not been studied extensively. There is also a lack of fundamental understanding about the process and the mechanisms through which a coating becomes destabilized. High pressure (2100 bar) freezing fixes the state of water-suspended particles of polymer binder and inorganic pigments without the growth of ice crystals during freezing that produce artifacts in direct imaging scanning electron microscopy (SEM) of fracture surfaces of frozen coatings. We show that by incorporating copolymerizable functional monomers, it is possible to achieve F/T stability in polymer latexes and in low-VOC paints, as judged by the microstructures revealed by the cryogenic SEM technique. Particle coalescence as well as pigment segregation in F/T unstable systems are visualized. In order to achieve F/T stability in paints, latex particles must not flocculate and should provide protection to inorganic pigment and extender particles. Because of the unique capabilities of the cryogenic SEM, we are able to separate the effects of freezing and thawing, and study the influence of the rate of freezing and thawing on F/T stability. Destabilization can be caused by either freezing or thawing. A slow freezing process is more detrimental to F/T stability than a fast freezing process; the latter actually preserves suspension stability during freezing. Presented at the 82nd Annual Meeting of the Federation of Societies for Coatings Technology, October 27–29, 2004 in Chicago, IL. Tied for first place in The John A. Gordon Best Paper Competition.     

Ethanol and (−)-α-Pinene: Attractant Kairomones for Bark and Ambrosia Beetles in the Southeastern US

In 2002–2004, we examined the flight responses of 49 species of native and exotic bark and ambrosia beetles (Coleoptera: Scolytidae and Platypodidae) to traps baited with ethanol and/or (−)-α-pinene in the southeastern US. Eight field trials were conducted in mature pine stands in Alabama, Florida, Georgia, North Carolina, and South Carolina. Funnel traps baited with ethanol lures (release rate, about 0.6 g/day at 25–28°C) were attractive to ten species of ambrosia beetles (Ambrosiodmus tachygraphus, Anisandrus sayi, Dryoxylon onoharaensum, Monarthrum mali, Xyleborinus saxesenii, Xyleborus affinis, Xyleborus ferrugineus, Xylosandrus compactus, Xylosandrus crassiusculus, and Xylosandrus germanus) and two species of bark beetles (Cryptocarenus heveae and Hypothenemus sp.). Traps baited with (−)-α-pinene lures (release rate, 2–6 g/day at 25–28°C) were attractive to five bark beetle species (Dendroctonus terebrans, Hylastes porculus, Hylastes salebrosus, Hylastes tenuis, and Ips grandicollis) and one platypodid ambrosia beetle species (Myoplatypus flavicornis). Ethanol enhanced responses of some species (Xyleborus pubescens, H. porculus, H. salebrosus, H. tenuis, and Pityophthorus cariniceps) to traps baited with (−)-α-pinene in some locations. (−)-α-Pinene interrupted the response of some ambrosia beetle species to traps baited with ethanol, but only the response of D. onoharaensum was interrupted consistently at most locations. Of 23 species of ambrosia beetles captured in our field trials, nine were exotic and accounted for 70–97% of total catches of ambrosia beetles. Our results provide support for the continued use of separate traps baited with ethanol alone and ethanol with (−)-α-pinene to detect and monitor common bark and ambrosia beetles from the southeastern region of the US.     

Methyl 2,4,6-decatrienoates Attract Stink Bugs and Tachinid Parasitoids

Halyomorpha halys (Stål) (Pentatomidae), called the brown marmorated stink bug (BMSB), is a newly invasive species in the eastern USA that is rapidly spreading from the original point of establishment in Allentown, PA. In its native range, the BMSB is reportedly attracted to methyl (E,E,Z)-2,4,6-decatrienoate, the male-produced pheromone of another pentatomid common in eastern Asia, Plautia stali Scott. In North America, Thyanta spp. are the only pentatomids known to produce methyl 2,4,6-decatrienoate [the (E,Z,Z)-isomer] as part of their pheromones. Methyl 2,4,6-decatrienoates were field-tested in Maryland to monitor the spread of the BMSB and to explore the possibility that Thyanta spp. are an alternate host for parasitic tachinid flies that use stink bug pheromones as host-finding kairomones. Here we report the first captures of adult and nymph BMSBs in traps baited with methyl (E,E,Z)-2,4,6-decatrienoate in central Maryland and present data verifying that the tachinid, Euclytia flava (Townsend), exploits methyl (E,Z,Z)-2,4,6-decatrienoate as a kairomone. We also report the unexpected finding that various isomers of methyl 2,4,6-decatrienoate attract Acrosternum hilare (Say), although this bug apparently does not produce methyl decatrienoates. Other stink bugs and tachinids native to North America were also attracted to methyl 2,4,6-decatrienoates. These data indicate there are Heteroptera in North America in addition to Thyanta spp. that probably use methyl 2,4,6-decatrienoates as pheromones. The evidence that some pentatomids exploit the pheromones of other true bugs as kairomones to find food or to congregate as a passive defense against tachinid parasitism is discussed.     

2007～2008年世界塑料工业进展

收集了2007年7月～2008年6月世界塑料工业的相关资料,介绍了2007～2008年国外塑料工业的发展情况,提供了世界塑料产量、消费量及全球各类树脂的需求量及产能情况.按通用热塑性树脂(聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂)、工程塑料(尼龙、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚)、特种工程塑料(聚苯·硫醚、液晶聚合物、聚醚醚酮)、通用热固性树脂(酚醛、聚氨酯、不饱和聚酯树脂、环氧树脂)不同品种的顺序,对树脂的产量、消费量、供需状况及合成工艺、产品应用开发、树脂品种的延伸及应用的进一步扩展等技术作了详细介绍.     

2005～2006年国外塑料工业进展

收集了2005年7月～2006年6月国外塑料工业的相关资料,介绍了2005—2006年国外塑料工业的发展情况。提供了世界塑料产量、消费量及全球各类树脂生产量以及各国塑料制品的进出口情况。作为对比,介绍了中国塑料的生产情况。按通用热塑性树脂（聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂）、工程塑料（聚酰胺、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚）、通用热固性树脂（酚醛、聚氨酯、不饱和树脂、环氧树脂）、特种工程塑料（聚苯硫醚、液晶聚合物、聚醚醚酮）的品种顺序,对树脂的产量、消费量、供需状况及合成工艺、产品开发、树脂品种的延伸及应用的扩展作了详细的介绍。