AUTOMATIC SEAM TRACKING SYSTEM OF SUBMERGED ARC WELDING BASED ON FUZZY-P CONTROLLER

An automatic seam tracking system used in submerged arc welding is presented. In the system, the linear CCD vision sensor is installed in front of the welding torch. Laser structure light emitted by the semiconductor laser irradiates on a slant to work-piece surface and forms a structure light strip on work-piece surface. Scatter light of the strip is received by linear CCD on top of the seam and the image information of seam can be obtained. By way of image processing and applying Fuzzy-P controller in tracking process, automatic seam tracking has been realized accurately. Anti-disturbing ability of the system to work-piece surface status has been enhanced largely by classified microadjus-tment of torch height.     

Basic Characteristics of a New Flexible Pneumatic Bending Joint

Several typical flexible pneumatic actuators （FPA） and different mechanical models describing their behaviors have been proposed, however, it is difficult to balance compliance and load capacity in conventional designs, and these models still have limitations in predicting behavior of FPAs. A new flexible pneumatic bending joint （FPBJ） with special anisotropic rigidity structure is proposed. The FPBJ is developed as an improvement with regard to existing types of FPA, and its principal characteristic is derived from the special anisotropic rigidity structure. With this structure, the load capacity in the direction perpendicular to bending plane is strengthened. The structure of the new FPBJ is explained and a mathematical model is derived based on Euler-Bernoulli beam model and Hook’s law. To obtain optimum design and usage, some key structure parameters and input-output characteristics are simulated. The simulation results reveal that the relationship between the structure parameters and FPBJ’s bending angle is nonlinear. At last, according to the simulation results, the FPBJ is manufactured with optional parameters and tested. The experimental results show that the joint’s statics characteristics are reflected by the mathematical model accurately when the FPBJ is deflated. The maximum relative error between simulation and experimental results is less than 6%. However, the model still has limitations. When the joint is inflated, the maximum relative error reaches 20%. This paper proposes a new flexible pneumatic bending joint which has sufficient load capacity and compliance, and the mathematical model provides theoretical guidance for the FPBJ’s structure design.     

Pseudo-rigid-body model for corrugated cantilever beam used in compliant mechanisms

Common compliant joints generally have limited range of motion, reduced fatigue life and high stress concentration. To overcome these shortcomings, periodically corrugated cantilever beam is applied to design compliant joints. Basic corrugated beam unit is modeled by using pseudo-rigid-body method. The trajectory and deformation behavior of periodically corrugated cantilever beam are estimated by the transformation of coordinate and superposition of the deformation of corrugated beam units. Finite element analysis（FEA） is carried out on corrugated cantilever beam to estimate the accuracy of the pseudo-rigid-body model. Results show that the kinetostatic behaviors obtained by this method, which has a relative error less than 6%, has good applicability and corrugated cantilever beam has the characteristics of a large range of motion and high mechanical strength. The corrugated cantilever beam is then applied to design a flexible rotational joint to obtain a larger angle output. The paper proposes a pseudo-rigid-body model for corrugated cantilever beam and designed a flexible rotational joint with large angle output.     

Modeling of fatigue crack growth closure considering the integrative effect of cyclic stress ratio, specimen thickness and Poisson’s ratio

Key components of large structures in aeronautics industry are required to be made light and have long enough fatigue lives.It is of vital importance to estimate the fatigue life of these structures accurately.Since the FCG process is affected by various factors,no universal model exists due to the complexity of the mechanisms.Most of the existing models are obtained by fitting the experimental data and could hardly describe the integrative effect of most existing factors simultaneously.In order to account for the integrative effect of specimen parameters,material property and loading conditions on FCG process,a new model named integrative influence factor model(IIF) is proposed based on the plasticity-induced crack closure theory.Accordingly to the predictions of crack opening ratio(γ) and effective stress intensity factor range ratio(U) with different material under various loading conditions,predictions of γ and U by the IIF model are completely identical to the theoretical results from the plane stress state to the plane strain state when Poisson’s ratio equals 1/3.When Poisson’s ratio equals 0.3,predictions of γ and U by the IIF model are larger than the predictions by the existing model,and more close to the theoretical results.In addition,it describes the influence of R ratios on γ and U effectively in the whole region from-1.0 to 1.0.Moreover,several sets of test data of FCG rates in 5 kinds of aluminum alloys with various specimen thicknesses under different loading conditions are used to validate the IIF model,most of the test data are situated on the predicted curves or between the two curves that represent the specimen with different thicknesses under the same stress ratio.Some of the test data slightly departure from the predictions by the IIF model due to the surface roughness and errors in measurement.Besides,based on the analysis of the physical rule of crack opening ratios,a relative thickness of specimen is defined to describe the influence of material property,specimen thickness and so forth on FCG characteristics conveniently.In conclusion,the relative thickness of specimen simplifies the expression of FCG characteristic and provides a general parameter to analyze the fatigue characteristics of different materials with various thicknesses under different loading conditions.The IIF model describes the integrative effect of existing influence factors explicitly and quantitatively,and provides a helpful tool for fatigue property estimation of practical component and experiment design.     

The Friction Welding Method with Intermediate Material

For the purpose of improving the defects of the conventional friction welding method, the new friction welding technology has been examined. That is, the aim of the study is producing the joint of dissimilar materials evaluated to be difficult for friction welding and non-round shape joints. In this process, after the intermediate material generates the independent friction heat on every side of the specimens, it is removed instantaneously and upset process begins to weld the specimens for a joint. In this study, similar joint of A2017 aluminum alloy and one of S45C steel were examined. On the other hand, thermal elastic-plastic stress analysis by the finite element method was carried out using ANSYS mechanical.     

Three-dimensional finite element analysis of the mechanical properties of helical thread connection

Conventional analytical and numerical methods for the mechanical properties of helical threads are relied on many assumptions and approximations and thus hardly yield satisfied results. A parameterized 3D finite element model of bolted joints with real helical thread geometry is established and meshed with refined hexahedral elements. The Von Mises plasticity criterion, kinematic hardening rule of materials and interfacial contacts are employed to make it possible for the suggested model be able to approach real assembly conditions. Then, the mechanical properties of bolted joints with different thread pitches, thread numbers and modular ratios are investigated, including the contact pressure distribution at joint interfaces, the axial load distribution and stress concentration in screw threads during the loading and unloading process. Simulation results indicate that the load distribution in screw threads produced by the suggested model agrees well the results from CHEN’s photoelastic tests. In addition, an interesting phenomenon is found that tightening the bolt with a large preload first and then adjusting the clamping force by unloading can make the load distribution more uniform and reduce the maximum residual equivalent stress in thread roots by up to 40%. This research provides a simple and practical approach to constructing the 3D finite element model and predicting the mechanical properties of helical thread connection.     

Motion error compensation of multi-legged walking robots

Existing errors in the structure and kinematic parameters of multi-legged walking robots,the motion trajectory of robot will diverge from the ideal sports requirements in movement.Since the existing error compensation is usually used for control compensation of manipulator arm,the error compensation of multi-legged robots has seldom been explored.In order to reduce the kinematic error of robots,a motion error compensation method based on the feedforward for multi-legged mobile robots is proposed to improve motion precision of a mobile robot.The locus error of a robot body is measured,when robot moves along a given track.Error of driven joint variables is obtained by error calculation model in terms of the locus error of robot body.Error value is used to compensate driven joint variables and modify control model of robot,which can drive the robots following control model modified.The model of the relation between robot’s locus errors and kinematic variables errors is set up to achieve the kinematic error compensation.On the basis of the inverse kinematics of a multi-legged walking robot,the relation between error of the motion trajectory and driven joint variables of robots is discussed.Moreover,the equation set is obtained,which expresses relation among error of driven joint variables,structure parameters and error of robot’s locus.Take MiniQuad as an example,when the robot MiniQuad moves following beeline tread,motion error compensation is studied.The actual locus errors of the robot body are measured before and after compensation in the test.According to the test,variations of the actual coordinate value of the robot centroid in x-direction and z-direction are reduced more than one time.The kinematic errors of robot body are reduced effectively by the use of the motion error compensation method based on the feedforward.     

DESIGN OF A NOVEL DEXTEROUS ROBOT HAND

In the robotic community more and more hands are developed. Based on the experience of HIT Hand and DLR Hand Ⅱ, a smaller and easier manufactured dexterous robot hand with multisen-sory function and high integration is jointly developed. The prototype of the hand is successfully built. It has 4 fingers in total 13-DOFs (degree of freedom). Each finger has 3-DOFs and 4 joints, the last 2 joints are mechanically coupled by means of four-bar linkage mechanism. It also has an additional DOF to realize motion of the thumb relative to the palm. The fingertip force can reach up to 10N. Full integration of mechanical body, actuation system, multisensory system and electronics is a significant feature. DSP based control system is implemented in PCI bus architecture and the serial communication between the hand and DSP needs only 2 lines.     

Dynamics and Wheel’s Slip Ratio of a Wheel-legged Robot in Wheeled Motion Considering the Change of Height

The existing research on dynamics and slip ratio of wheeled mobile robot (WMR) are derived without considering the effect of height, and the existing models can not be used to analyze the dynamics performance of the robot with variable height while moving such as NOROS-Ⅱ. The existing method of dynamics modeling is improved by adding the constraint equation between perpendicular displacement of body and horizontal displacement of wheel into the constraint conditions. The dynamic model of NOROS-Ⅱ in wheel motion is built by the Lagrange method under nonholonomic constraints. The inverse dynamics is calculated in three different paths based on this model, and the results demonstrate that torques of hip pitching joints are inversely proportional to the height of robot. The relative error of calculated torques is less than 2% compared with that of ADAMS simulation, by which the validity of dynamic model is verified. Moreover, the relative horizontal motion between fore?hind wheels and body is produced when the height is changed, and thus the accurate slip ratio can not be obtained by the traditional equation. The improved slip ratio equations with the parameter of the vertical velocity of body are introduced for fore wheels and hind wheels respectively. Numerical simulations of slip ratios are conducted to reveal the effect of varied height on slip ratios of different wheels. The result shows that the slip ratios of fore?hind wheels become larger?smaller respectively as the height increases, and as the height is reduced, the reverse applies. The proposed research of dynamic model and slip ratio based on the robot height provides the effective method to analyze the dynamics of WMRs with varying height.     

Application of Nd:YAG Laser Welding to Implantable Neuro-Stimulator

It is difficult to weld the material and structure of implantable neuro-stimulator such as pure medical titanium and irregular outside shield by conventional arc welding methods.Currently there are few reports on the neuro stimulator sealing technology,and none of them have simultaneously considered the quality control methods.In order to develop the sealing procedure and quality control methods,an investigation of applying Nd:YAG laser welding to implantable neuro-stimulator components is carried out.Firstly,the automatic Nd:YAG laser welding system equipped with proper fixture configuration is introduced.A special fixture structure is illustrated and the key point for the device is to reduce the fit-up gap between the two shields.Then,a novel welding process technique is proposed to satisfy the engineering requirements.The optimized process parameters for titanium shell,feedthrough and fastener are provided and concluded by an orthogonal experiment.Finally,different quality control measures such as visual inspection,X-ray detecting and leakage testing,are presented on the final products.The results show that the Nd:YAG laser welding applied on the implanted neuro-stimulator under optimized parameters can prevent welding defects and improve the weld joints quality.Combination of various quality control methods will guarantee the sealing performance and mechanical properties of the products.It is confirmed that the processing procedure and quality methods can not only resolve the process technology on welding ultra-thin structure of medical device,but also provide the reference for other implantable device.     

FORCE FEEDBACK DATAGLOVE BASED ON PNEUMATIC ARTIFICIAL MUSCLES

An exoskeleton force feedback dataglove is developed, which uses the pneumatic artificial muscles as actuators. On the basis of the simplified hand model, the motion equation is deduced according to the theory of Denavit-Hartenberg. The model of the equivalent contact forces exerted by the object on the finger is proposed. By the principle of virtual work, the static equilibrium of finger is established. The force Jacobian matrix of finger is calculated, and then the joint torques of the finger when grasping objects are obtained. The theory and structure of the force feedback datagolve are introduced. Based on the theory of motion stabilization of four-bar linkage, the flexion angles of joints are measured. The torques on finger joints caused by the output forces of pneumatic artificial muscles are calculated. The output forces of pneumatic artificial muscle, whose values are controlled by its inner pressure, can be calculated by the joint torques of the finger when grasping objects. The arms of force, driving torques and the needed output forces of pneumatic muscle are calculated for each joint of the index finger. The criterion of output force of pneumatic muscle is given.     

Analytical Higher-Order Model for Flexible and Stretchable Sensors

The stretchable sensor wrapped around a foldable airfoil or embedded inside of it has great potential for use in the monitoring of the structural status of the foldable airfoil.The design methodology is important to the development of the stretchable sensor for status monitoring on the foldable airfoil.According to the requirement of mechanical flexibility of the sensor,the combined use of a layered flexible structural formation and a strain isolation layer is implemented.An analytical higher-order model is proposed to predict the stresses of the strain-isolation layer based on the shear-lag model for the safe design of the flexible and stretchable sensors.The normal stress and shear stress equations in the constructed structure of the sensors are obtained by the proposed model.The stress distribution in the structure is investigated when bending load is applied to the structures.The numerical results show that the proposed model can predict the variation of normal stress and shear stress along the thickness of the strain-isolation(polydimethylsiloxane)layer accurately.The results by the proposed model are in good agreement with the finite element method,in which the normal stress is variable while the shear stress is invariable along the thickness direction of strain-isolation layer.The high-order model is proposed to predict the stresses of the layered structure of the flexible and stretchable sensor for monitoring the status of the foldable airfoil.     

COMPREHENSIVE EVALUATION OF FAULT-TOLERANT PROPERTIES OF REDUNDANT ROBOTS

When a redundant robot performs a fault-tolerant operation for locked joint failures, its fault tolerant properties should include dexterity and sudden change of joint velocity at the moment of locking failed joints and the dexterity during the post-failure. Firstly three fault-tolerant indexes, reduced condition number, sudden change of relative joint velocity and centrality are proposed, which can comprehensively evaluate the kinematical performance of a redundant robot during its entire fault-tolerant operations. Then, the influence of the initial postures of robot＇s end-effector on these fault-tolerant indexes is analyzed with a planar robot and a spatial robot. Simulation results show that for a given task the joint trajectory with the best comprehensive effect of fault tolerance can be determined by optimizing the initial posture of a robot.     

Progressive Failure Analysis of Composite/Aluminum Riveted Joints Subjected to Pull-Through Loading

Out-of-plane mechanical properties of the riveted joints restrict the performance of the wing box assembly of airplane. It is necessary to investigate the pull-through performance of the composite/metal riveted joints in order to guide the riveting design and ensure the safety of the wing box assembly. The progressive failure mechanism of composite/aluminum riveted joint subjected to pull-through loading was investigated by experiments and finite element method. A progressive damage model based ...     

Simulation of the interaction between driver and seat

Test is one of methods to acquire human-seat pressure distribution in driving, with the deficiency of being uneasy to obtain the stress information of soft tissue inside human body and the sheer force of interface between human and seat, which can be obtained by simulation. But current simulation method focuses mainly on calculation itself other than combining it with posture prediction and cab packaging parameters, which cause it difficult to acquire accurate pressure calculation results without accurate posture of human body, and make it almost meaningless to design optimization. Therefore, a human body geometric model with posture change capability is built and linked up with Cascade Prediction Model（CPM）, which takes cab packaging parameters as inputs. A detailed finite element model of driver human body is constructed and used to conduct the driver-seat interaction simulation between human body and seat. Good accordance of pressure distribution is observed between simulation and test, which validates the simulation. In addition to the distribution pattern, curves on key sections are used to analyze the pressure and shear stress on the seat surface, as well as soft tissue stress inside human body. The simulation shows that the maximum stress of buttocks locates under the ischial tuberosity, and the maximum stress of trunk occurs near the scapula posterior and the lower waist. These are the places where fatigue usually occurs. The maximum pressure of seat appears at the driver-seat contact area corresponding to the driver＇s maximum skin tissue stress. In order to guide the seat design and cab packaging and study the influence of posture to pressure distribution, finite element models for different levels of cab packaging parameters are created by using CPM. The pressure distributions are calculated and their tendencies varying with cab packaging parameters are obtained. The method presented provides a new way to accurately simulate the interaction between driver human body and seat, and to guide the seat design and cab packaging so as to improve seating comfort.     

Welding polarity effects on weld spatters and bead geometry of hyperbaric dry GMAW

Welding polarity has influence on welding stability to some extent, but the specific relationship between welding polarity and weld quality has not been found, especially under the hyperbaric environment. Based on a hyperbaric dry welding experiment system, gas metal arc welding(GMAW) experiments with direct current electrode positive(DCEP) and direct current electrode negative(DCEN) operations are carried out under the ambient pressures of 0.1 MPa, 0.4 MPa, 0.7 MPa and 1.0 MPa to find the influence rule of different welding polarities on welding spatters and weld bead geometry. The effects of welding polarities on the weld bead geometry such as the reinforcement, the weld width and the penetration are discussed. The experimental results show that the welding spatters gradually grow in quantity and size for GMAW with DCEP, while GMAW with DCEN can produce fewer spatters comparatively with the increase of the ambient pressure. Compared with DCEP, the welding current and arc voltage waveforms for DCEN is more stable and the distribution of welding current probability density for DCEN is more concentrated under the hyperbaric environment. When the ambient pressure is increased from 0.1 MPa to 1.0 MPa, the effects of welding polarities on the reinforcement, the weld width and the penetration are as follows: an increase of 0.8 mm for the weld reinforcement is produced by GMAW with DCEN and 1.3 mm by GMAW with DCEP, a decrease of 7.2 mm for the weld width is produced by DCEN and 6.1 mm by DCEP; and an increase of 3.9 mm for the penetration is produced by DCEN and 1.9 mm by DCEP. The proposed research indicates that the desirable stability in the welding procedure can be achieved by GMAW with DCEN operation under the hyperbaric environment.     

Product Data Model for Performance-driven Design

When designing large-sized complex machinery products,the design focus is always on the overall performance;however,there exist no design theory and method based on performance driven.In view of the deficiency of the existing design theory,according to the performance features of complex mechanical products,the performance indices are introduced into the traditional design theory of‘‘Requirement-Function-Structure’’to construct a new five-domain design theory of‘‘Client Requirement-Function-Performance-Structure-Design Parameter’’.To support design practice based on this new theory,a product data model is established by using performance indices and the mapping relationship between them and the other four domains.When the product data model is applied to high-speed train design and combining the existing research result and relevant standards,the corresponding data model and its structure involving five domains of high-speed trains are established,which can provide technical support for studying the relationships between typical performance indices and design parameters and the fast achievement of a high-speed train scheme design.The five domains provide a reference for the design specification and evaluation criteria of high speed train and a new idea for the train’s parameter design.     

Effects of joint on dynamics of space deployable structure

Joints are necessary components in large space deployable truss structures which have significant effects on dynamic behavior of these joint dominated structures.Previous researches usually analyzed effects of one or fewer joint characters on dynamics of jointed structures.Effects of joint stiffness,damping,location,number,clearance and contact stiffness on dynamics of jointed structures are systematically analyzed.Cantilever beam model containing linear joints is developed based on finite element method,influence of joint on natural frequencies and mode shapes of the jointed system are analyzed.Analytical results show that frequencies of jointed system decrease dramatically when peak mode shapes occur at joint locations,and there are cusp shapes present in mode shapes.System frequencies increase with joint damping increasing,there are different joint damping to achieve maximum system damping for different joint stiffness.Joint nonlinear force-displacement is described by describing function method,one-DOF model containing nonlinear joints is established to analyze joints freeplay and hysteresis nonlinearities.Analysis results show that nonlinear effects of freeplay and hysteresis make dynamic responses switch from one resonance frequency to another frequency when amplitude exceed demarcation values.Joint contact stiffness determine degree of system nonlinearity,while exciting force level,clearance and slipping force affect amplitude of dynamic response.Dynamic responses of joint dominated deployable truss structure under different sinusoidal exciting force levels are tested.The test results show obvious nonlinear behaviors contributed by joints,dynamic response shifts to lower frequency and higher amplitude as exciting force increasing.The test results are further compared with analytical results,and joint nonlinearity tested is coincident with hysteresis nonlinearity.Analysis method of joint effects on dynamic characteristics of jointed system is proposed,which can be used in optimal design of joint parameters     

Structural scheme optimization design for the stationary platen of a precision plastic injection molding machine

The current development of precision plastic injection molding machines mainly focuses on how to save material and improve precision, but the two aims contradict each other. For a clamp unit, clamping precision improving depends on the design quality of the stationary platen. Compared with the parametric design of stationary platen, structural scheme design could obtain the optimization model with double objectives and multi-constraints. In this paper, a SE-160 precision plastic injection molding machine with 1600 kN clamping force is selected as the subject in the case study. During the motion of mold closing and opening, the stationary platen of SE-160 is subjected to a cyclic loading, which would cause the fatigue rupture of the tie bars in periodically long term operations. In order to reduce the deflection of the stationary platen, the FEA method is introduced to optimize the structure of the stationary platen. Firstly, an optimal topology model is established by variable density method. Then, structural topology optimizations of the stationary platen are done with the removable material from 50%, 60% to 70%. Secondly, the other two recommended optimization schemes are given and compared with the original structure. The result of performances comparison shows that the scheme II of the platen is the best one. By choosing the best alternative, the volume and the local maximal stress of the platen could be decreased, corresponding to cost-saving material and better mechanical properties. This paper proposes a structural optimization design scheme, which can save the material as well as improve the clamping precision of the precision plastic injection molding machine.     

Metal Sealing Performance of Subsea X-tree Wellhead Connector Sealer

The metal sealing performance of subsea X-tree wellhead connectors is crucial for the safety and reliability of subsea X-trees. In order to establish the theoretical relation between metal sealing ring’s contact stress and its structural parameters and working pressure, a mechanical analysis method for double-cone sealing of high pressure vessels is applied in analyzing the metal sealing ring under the condition of preload and operation. As a result, the formula of the unit sealing load for the metal sealing ring under operation with residual preload is shown in this paper, which ensures that the metal sealing ring has an excellent sealing effect and can prevent the metal sealing ring from yielding. Besides, while analyzing the sealing process of the metal sealing ring, the change rule of contact stress and working pressure is concluded here, putting forward that the structural parameters of the metal sealing ring are the major factors affecting the change rule. Finally, the analytical solution through theoretical analysis is compared with the simulation result through finite element analysis in a force feedback experiment, and both are consistent with each other, which fully verifies for the design and calculation theory on metal sealing ring’s contact stress and its structural parameters and working pressure deduced in this paper. The proposed research will be treated as an applicable theory guiding the design of metal seal for subsea X-tree wellhead connectors.