Low-threshold proton-implanted 1.3-/spl mu/m vertical-cavity top-surface-emitting lasers with dielectric and wafer-bonded GaAs-AlAs Bragg mirrors

We demonstrate a new structure for long-wavelength (1.3-/spl mu/m) vertical-cavity top-surface-emitting lasers using proton implantation for current confinement. Wafer bonded GaAs-AlAs Bragg mirrors and dielectric mirrors are used for bottom and top mirrors, respectively. The gain medium of the lasers consists of nine strain-compensated AlGaInAs quantum wells. A record low room temperature pulsed threshold current density of 1.13 kA/cm/sup 2/ has been achieved for 15-/spl mu/m diameter devices with a threshold current of 2 mA. The side-mode-suppression-ratio is greater than 35 dB.     

Low threshold current 1.3-/spl mu/m GaInNAs VCSELs grown by MOVPE

The structure of the conventional contact 1.3-/spl mu/m GaInNAs-GaAs vertical-cavity surface-emitting lasers (VCSELs) was optimized and low threshold current 1.3-/spl mu/m GaInNAs VCSELs grown by metal-organic vapor-phase epitaxy were reported. The idea is to optimize the active region, the doping profiles, and the pairs of p-distributed Bragg reflectors, and the detuning between the emission wavelength and the photoluminescence gain peak wavelength. The continuous-wave 1.0-mA threshold current was achieved for the single-mode VCSEL. For the multiple-mode VCSELs, the below 2-mA threshold currents at 5/spl deg/C-85/spl deg/C , the 1.13-mA threshold current at 55/spl deg/C, and 1.52-mA threshold current at 85/spl deg/C are the best results for 1.3-/spl mu/m GaInNAs VCSELs.     

Room-temperature pulsed operation of 1.5-/spl mu/m vertical cavity lasers with an InP-based Bragg reflector

We report on a 1.5-/spl mu/m vertical-cavity laser that utilizes one GaInAsP-InP and one Si-SiO/sub 2/ mirror in combination with a strain-compensated GaInAsP quantum-well active layer. Pulsed lasing operation was achieved in a temperature range from -160 to +43/spl deg/C. The lasers exhibit 30-mA pulsed threshold current at room temperature. CW operation was obtained up to -25/spl deg/C.     

High-performance 1.06-/spl mu/m selectively oxidized vertical-cavity surface-emitting lasers with InGaAs-GaAsP strain-compensated quantum wells

We present the first room-temperature continuous-wave operation of high-performance 1.06-/spl mu/m selectively oxidized vertical-cavity surface-emitting lasers (VCSEL's). The lasers contain strain-compensated InGaAs-GaAsP quantum wells (QW's) in the active region grown by metalorganic vapor phase epitaxy. The threshold current is 190 /spl mu/A for a 2.5/spl times/2.5 /spl mu/m/sup 2/ device, and the threshold voltage is as low as 1.255 V for a 6/spl times/6 /spl mu/m/sup 2/ device. Lasing at a wavelength as long as 1.1 /spl mu/m was also achieved. We discuss the wavelength limit for lasers using the strain-compensated QW's on GaAs substrates.     

Continuous-wave operation up to 36/spl deg/C of 1.3-/spl mu/m GaInAsP-InP vertical-cavity surface-emitting lasers

We introduced ion-beam assisted deposition in order to improve the quality of Al/sub 2/O/sub 3/ and SiO/sub 2/, which were used as part of the mirrors of 1.3-/spl mu/m GaInAsP-InP vertical-cavity surface-emitting lasers (VCSELs). The refractive index of Al/sub 2/O/sub 3/ was improved to 1.63 from 1.56 and the one of SiO/sub 2/ increased to 1.47 from 1.45. Low-threshold room-temperature continuous-wave (CW) operation of 1.3-/spl mu/m VCSEL with the improved mirrors was demonstrated. The threshold current was 2.4 mA at 20/spl deg/C. The CW operating temperature was raised to 36/spl deg/C, which is a record high temperature for 1.3-/spl mu/m VCSEL.     

Type-II interband cascade lasers in the 4.3-4.7-/spl mu/m wavelength region

Operation of type-II interband cascade lasers in the 4.3-4.7-/spl mu/m wavelength region has been demonstrated at temperatures up to 240 K in pulsed mode. These lasers fabricated with 150-/spl mu/m-wide mesa stripes operated in continuous-wave (CW) mode up to a maximum temperature of 110 K, with an output power exceeding 30 mW/f and a threshold current density of about 41 A/cm/sup 2/ at 90 K. The maximum CW operation temperature of 110 K is largely limited by the high specific thermal resistance of the 150-/spl mu/m-wide broad area lasers. A 20-/spl mu/m-wide mesa stripe laser was able to operate in CW mode at higher temperatures up to 125 K as a result of the reduced specific thermal resistance of a smaller device.     

Flip-chip bonded 0.85-/spl mu/m bottom-emitting vertical-cavity laser array on an AlGaAs substrate

We report high-performance 0.85-/spl mu/m bottom-emitting vertical-cavity surface-emitting lasers (VCSELs) on an AlGaAs substrate with 2.1 mA threshold current density 4.2 mW maximum output power, 11.7% power conversion efficiency and a maximum operating temperature of 130/spl deg/C. We also demonstrate a flip-chip bonded 0.85-/spl mu/m bottom-emitting VCSEL array, and confirm all pixels across the 8/spl times/8 VCSEL array operate at a f/sub 3/ dB bandwidth of 2.6 GHz at only 4.2 mA.     

High-temperature (T=490 K) operation of 5.8 /spl mu/m quantum cascade lasers with InP/GaInAs waveguides

5.8 /spl mu/m Ga/sub 0.4/In/sub 0.6/As/Al/sub 0.56/In/sub 0.44/As strain-compensated quantum-cascade lasers with InP and GaInAs cladding layers using solid-source molecular-beam epitaxy have been fabricated. Low threshold current densities and high-temperature operation of uncoated devices, with a record value of 490 K, have been achieved in pulsed mode.     

MOVPE-grown GaInNAs VCSELs at 1.3 /spl mu/m with conventional mirror design approach

1.3 /spl mu/m oxide confined GaInNAs VCSELs designed using the same design philosophy used for standard 850 nm VCSELs is presented. The VCSELs have doped mirrors, with graded and highly doped interfaces, and are fabricated using production-friendly procedures. Multimode VCSELs (11 /spl mu/m oxide aperture) with an emission wavelength of 1287 nm have a threshold current of 3 mA and produce 1 mW of output power at 20/spl deg/C. The maximum operating temperature is 95/spl deg/C. Emission at 1303 nm with 1 mW of output power and a threshold current of 7 mA has been observed from VCSELs with a larger detuning between the gain peak and the cavity resonance.     

High-power ridge waveguide InGaAsN lasers fabricated with pulsed anodic oxidation

High-power InGaAsN triple-quantum-well strain-compensated lasers grown by metal-organic chemical vapor deposition were fabricated with pulsed anodic oxidation. A maximum light power output of 145 mW was obtained from a 4-/spl mu/m ridge waveguide uncoated laser diode in continuous-wave (CW) mode at room temperature. The devices operated in CW mode up to 130/spl deg/C with a characteristic temperature of 138 K in range of 20/spl deg/C-90/spl deg/C.     

Low-threshold operation of 1.34-/spl mu/m GaInNAs VCSEL grown by MOVPE

Low-threshold operation was demonstrated for a 1.34-/spl mu/m vertical-cavity surface-emitting laser (VCSEL) with GaInNAs quantum wells (QWs) grown by metal-organic vapor-phase epitaxy. Optimizing the growth conditions and QW structure of the GaInNAs active layers resulted in edge-emitting lasers that oscillated with low threshold current densities of 0.87 kA/cm/sup 2/ at 1.34 /spl mu/m and 1.1 kA/cm/sup 2/ at 1.38 /spl mu/m, respectively. The VCSEL had a low threshold current of 2.8 mA and a lasing wavelength of 1.342 /spl mu/m at room temperature and operated up to 60/spl deg/C.     

Room-temperature 2.81-/spl mu/m continuous-wave operation of GaInAsSb-AlGaAsSb laser

GaInAsSb-AlGaAsSb multiple quantum-well (QW) lasers with an emission wavelength of 2.81 /spl mu/m are reported. The ridge waveguide lasers with highly strained QWs show continuous-wave laser emission up to 25/spl deg/C; in pulsed mode, the lasers operate up to 60/spl deg/C. For pulsed operation, a threshold current density of 360 A/cm/sup 2/ is found for devices with 30-/spl mu/m stripe width and 2-mm cavity length at room temperature. A low threshold current density at infinite length of 248 A/cm/sup 2/ is derived.     

High efficiency long wavelength VCSEL on InP grown by MOCVD

High efficiency continuous-wave operation of 1.53 /spl mu/m vertical cavity surface emitting lasers (VCSELs) with buried tunnel junction grown by metal organic chemical vapour deposition (MOCVD) has been demonstrated. Devices show a high differential quantum efficiency of 46% and a singlemode power of 1 mW. Minimum threshold current and voltage are 0.45 mA and 1.3 V at room temperature, respectively for devices of 5 /spl mu/m diameter.     

Electrically-pumped vertical-cavity lasers with Al/sub x/O/sub y/-GaAs reflectors

We have fabricated the first electrically-pumped vertical-cavity surface-emitting lasers (VCSELs) which use oxide-based distributed Bragg reflectors (DBRs) on both sides of the gain region. They require a third the epitaxial growth time of VCSELs with semiconductor DBRs. We obtain threshold currents as low as 160 /spl mu/A in VCSELs with an active area of 8 /spl mu/m/spl times/8 /spl mu/m using a two quantum well InGaAs-GaAs active region. By etching away mirror pairs from the top reflector, quantum efficiencies as high as 61% are attained, while still maintaining a low threshold current of 290 /spl mu/A.     

High-performance 1.3 /spl mu/m InGaAs vertical cavity surface emitting lasers

A report is presented on high-performance InGaAs/GaAs double quantum well vertical cavity surface emitting lasers (VCSELs) with record long emission wavelengths up to 1300 nm. Due to a large gain-cavity detuning these VCSELs show excellent temperature performance with very stable threshold current and output power characteristics. For 1.27 /spl mu/m singlemode devices the threshold current is found to decrease from 2 to 1 mA between 10 and 90/spl deg/C, while the peak output power only drops from 1 to 0.6 mW. Large-area 1300 nm VCSELs show multimode output power close to 3 mW.     

High-T/sub 0/ strain-compensated InGaAsSb-AlGaAsSb quantum-well lasers emitting at 2.43 /spl mu/m

Strain-compensated InGaAsSb-AlGaAsSb quantum-well (QW) lasers emitting near 2.5 /spl mu/m have been grown by solid-source molecular beam epitaxy. The relatively high arsenic composition causing a tensile strain in the Al/sub 0.25/GaAs/sub 0.08/Sb barriers lowers the valence band edge and the hole energy level, leading to an increased hole confinement and improved laser performance. A 60% external differential efficiency in pulsed mode was achieved for 1000-/spl mu/m-long lasers emitting at 2.43 /spl mu/m. A characteristic temperature T/sub 0/ as high as 163 K and a lasing-wavelength temperature dependence of 1.02 nm//spl deg/C were obtained at room temperature. For 2000 /spl times/ 200 /spl mu/m/sup 2/ broad-area three-QW lasers without lateral current confinement, a low pulsed threshold of 275 A/cm/sup 2/ was measured.     

Strain-compensated InGaAsSb multiple quantum-wells with digital AlGaAsSb barriers for midinfrared lasers

Midinfrared InGaAsSb-AlGaAsSb strain-compensated multiple quantum-wells (SCMQW) have been grown by solid-source molecular beam epitaxy. Short-period (AlGaAsSb)/sub y/--(AlGaSb)/sub 1-y/ digital barriers were employed to avoid growth interruptions at the barrier-well interfaces, thereby significantly improving the structural and optical properties of the InGaAsSb SCMQW as evidenced by X-ray diffraction and photoluminescence measurements. Based on these high-quality SCMQW, a room-temperature threshold current density as low as 163 A/cm/sup 2/ was achieved for 1000-/spl mu/m-long broad-area lasers emitting at 2.38 /spl mu/m in pulsed mode. The 880-/spl mu/m-long lasers retained a high characteristic temperature (T/sub 0/) of 165 K up to 80/spl deg/C and could operate at temperatures above 100/spl deg/C. A typical wavelength blueshift of 38 meV was observed in the SCMQW laser samples compared to the SCMQW-only samples.     

High-speed Modulation of InGaAs: Sb-GaAs-GaAsP quantum-well vertical-cavity surface-emitting lasers with 1.27-/spl mu/m emission wavelength

1.27-/spl mu/m InGaAs: Sb-GaAs-GaAsP vertical-cavity surface-emitting lasers (VCSELs) were grown by metal-organic chemical vapor deposition and exhibited excellent performance and temperature stability. The threshold current changes from 1.8 to 1.1 mA and the slope efficiency falls less than /spl sim/35% as the temperature raised from room temperature to 70/spl deg/C. With a bias current of only 5 mA, the 3-dB modulation frequency response was measured to be 8.36 GHz, which is appropriate for 10-Gb/s operation. The maximal bandwidth is measured to be 10.7 GHz with modulation current efficiency factor (MCEF) of /spl sim/5.25 GHz/(mA)/sup 1/2/. These VCSELs also demonstrate high-speed modulation up to 10 Gb/s from 25/spl deg/C to 70/spl deg/C.     

Single-mode monolithic quantum-dot VCSEL in 1.3 /spl mu/m with sidemode suppression ratio over 30 dB

We present monolithic quantum-dot vertical-cavity surface-emitting lasers (QD VCSELs) operating in the 1.3-/spl mu/m optical communication wavelength. The QD VCSELs have adapted fully doped structure on GaAs substrate. The output power is /spl sim/330 /spl mu/W with slope efficiency of 0.18 W/A at room temperature. Single-mode operation was obtained with a sidemode suppression ratio of >30 dB. The modulation bandwidth and eye diagram in 2.5 Gb/s was also presented.     

Development of bottom-emitting 1300-nm vertical-cavity surface-emitting lasers

We present experimental results on the development of bottom-emitting GaInNAs vertical-cavity surface-emitting lasers (VCSELs) operating at wavelengths near 1300 nm. This development effort is based on the modification of oxide-apertured top-emitting structures to allow emission through the GaAs substrate. Similar device performance was seen in both the top- and bottom-emitting structures. Single-mode output powers (adjusted for substrate absorption) of /spl sim/0.75 mW, with threshold currents of 1.3 mA, were achieved with /spl sim/3.5-/spl mu/m aperture diameters. Larger multimode devices exhibited a maximum adjusted output power of 2.2 mW. To the best of our knowledge, these are the first bottom-emitting flip-chip compatible 1300-nm VCSELs fabricated with GaInNAs-GaAs active regions.