An RF front-end with an automatic gain control technique for a U/V band CMMB receiver

This paper presents a fully integrated RF front-end with an automatic gain control(AGC) scheme and a digitally controlled radio frequency varied gain amplifier(RFVGA) for a U/V band China Mobile Multimedia Broadcasting(CMMB) direct conversion receiver.The RFVGA provides a gain range of 50 dB with a 1.6 dB step. The adopted AGC strategy could improve immunity to adjacent channel signal,which is of importance for CMMB application.The front-end,composed of a low noise amplifier(LNA),an RFVGA,a mixer and AGC,achieves an input referred 3rd order intercept point(IIP3) of 4.9 dBm with the LNA in low gain mode and the RFVGA in medium gain mode,and a less than 4 dB double side band noise figure with both the LNA and the RFVGA in high gain mode.The proposed RF front-end is fabricated in a 0.35μm SiGe BiCMOS technology and consumes 25.6 mA from a 3.0 V power supply.     

用于U波段移动数字电视的宽带大动态范围高线性度射频前端

A wideband large dynamic range and high linearity U-band RF front-end for mobile DTV is introduced,and includes a noise-cancelling low-noise amplifier(LNA),an RF programmable gain amplifier(RFPGA) and a current communicating passive mixer.The noise/distortion cancelling structure and RC post-distortion compensation are employed to improve the linearity of the LNA.An RFPGA with five stages provides large dynamic range and fine gain resolution.A simple resistor voltage network in the passive mixer decreases the gate bias voltage of the mixing transistor,and optimum linearity and symmetrical mixing is obtained at the same time.The RF front-end is implemented in a 0.25 μm CMOS process.Tests show that it achieves an ⅡP3(third-order intercept point) of –17 dBm,a conversion gain of 39 dB,and a noise figure of 5.8 dB.The RFPGA achieves a dynamic range of –36.2 to 23.5 dB with a resolution of 0.32 dB.     

A multi-mode multi-band RF receiver front-end for a TD-SCDMA/LTE/LTE-advanced in 0.18-μm CMOS process

正A fully integrated multi-mode multi-band directed-conversion radio frequency(RF) receiver front-end for a TD-SCDMA/LTE/LTE-advanced is presented.The front-end employs direct-conversion design,and consists of two differential tunable low noise amplifiers(LNA),a quadrature mixer,and two intermediate frequency(IF) amplifiers.The two independent tunable LNAs are used to cover all the four frequency bands,achieving sufficient low noise and high gain performance with low power consumption.Switched capacitor arrays perform a resonant frequency point calibration for the LNAs.The two LNAs are combined at the driver stage of the mixer,which employs a folded double balanced Gilbert structure,and utilizes PMOS transistors as local oscillator(LO) switches to reduce flicker noise.The front-end has three gain modes to obtain a higher dynamic range.Frequency band selection and mode of configuration is realized by an on-chip serial peripheral interface(SPI) module.The frontend is fabricated in a TSMC 0.18-μm RF CMOS process and occupies an area of 1.3 mm~2.The measured doublesideband (DSB) noise figure is below 3.5 dB and the conversion gain is over 43 dB at all of the frequency bands. The total current consumption is 31 mA from a 1.8-V supply.     

A RF receiver frontend for SC-UWB in a 0.18-μm CMOS process

正A radio frequency(RF) receiver frontend for single-carrier ultra-wideband(SC-UWB) is presented. The front end employs direct-conversion architecture,and consists of a differential low noise amplifier(LNA),a quadrature mixer,and two intermediate frequency(IF) amplifiers.The proposed LNA employs source inductively degenerated topology.First,the expression of input impedance matching bandwidth in terms of gate-source capacitance, resonant frequency and target S_(11) is given.Then,a noise figure optimization strategy under gain and power constraints is proposed,with consideration of the integrated gate inductor,the bond-wire inductance,and its variation.The LNA utilizes two stages with different resonant frequencies to acquire flat gain over the 7.1-8.1 GHz frequency band,and has two gain modes to obtain a higher receiver dynamic range.The mixer uses a double balanced Gilbert structure.The front end is fabricated in a TSMC 0.18-/im RF CMOS process and occupies an area of 1.43 mm~2.In high and low gain modes,the measured maximum conversion gain are 42 dB and 22 dB,input 1 dB compression points are -40 dBm and -20 dBm,and S_(11) is better than -18 dB and -14.5 dB.The 3 dB IF bandwidth is more than 500 MHz.The double sideband noise figure is 4.7 dB in high gain mode.The total power consumption is 65 mW from a 1.8 V supply.     

A 0.18μm CMOS low noise amplifier using a current reuse technique for 3.1-10.6 GHz UWB receivers

A new,low complexity,ultra-wideband 3.1-10.6 GHz low noise amplifier(LNA),designed in a chartered 0.18μm RFCMOS technology,is presented.The ultra-wideband LNA consists of only two simple amplifiers with an inter-stage inductor connected.The first stage utilizing a resistive current reuse and dual inductive degeneration technique is used to attain a wideband input matching and low noise figure.A common source amplifier with an inductive peaking technique as the second stage achieves high flat gain and wide -3 dB bandwidth of the overall amplifier simultaneously.The implemented ultra-wideband LNA presents a maximum power gain of 15.6 dB,and a high reverse isolation of—45 dB,and good input/output return losses are better than -10 dB in the frequency range of 3.1-10.6 GHz.An excellent noise figure(NF) of 2.8-4.7 dB was obtained in the required band with a power dissipation of 14.1 mW under a supply voltage of 1.5 V.An input-referred third-order intercept point(IIP3) is -7.1 dBm at 6 GHz.The chip area,including testing pads,is only 0.8×0.9 mm2.     

Design of a low noise distributed amplifier with adjustable gain control in 0.15μm GaAs PHEMT

正A low noise distributed amplifier consisting of 9 gain cells is presented.The chip is fabricated with 0.15-μm GaAs pseudomorphic high electron mobility transistor(PHEMT) technology from Win Semiconductor of Taiwan.A special optional gate bias technique is introduced to allow an adjustable gain control range of 10 dB.A novel cascode structure is adopted to extend the output voltage and bandwidth.The measurement results show that the amplifier gives an average gain of 15 dB with a gain flatness of±1 dB in the 2-20 GHz band.The noise figure is between 2 and 4.1 dB during the band from 2 to 20 GHz.The amplifier also provides 13.8 dBm of output power at a 1 dB gain compression point and 10.5 dBm of input third order intercept point(IIP3),which demonstrates the excellent performance of linearity.The power consumption is 300 mW with a supply of 5 V,and the chip area is 2.36×1.01 mm~2.     

A 2.1-6 GHz SiGe BiCMOS low-noise amplifier design for a multi-mode wideband receiver

正A wideband low-noise amplifier(LNA) with ESD protection for a multi-mode receiver is presented.The LNA is fabricated in a 0.18-μm SiGe BiCMOS process,covering the 2.1 to 6 GHz frequency band.After optimized noise modeling and circuit design,the measured results show that the LNA has a 12 dB gain over the entire bandwidth, the input third intercept point(IIP3) is -8 dBm at 6 GHz,and the noise figure is from 2.3 to 3.8 dB in the operating band.The overall power consumption is 8 mW at 2.5 V voltage supply.     

Design of a fully differential CMOS LNA for 3.1-10.6 GHz UWB communication systems

A fully differential complementary metal oxide semiconductor （CMOS） low noise amplifier （LNA） for 3.1-10.6 GHz ultra-wideband （UWB） communication systems is presented. The LNA adopts capacitive cross-coupling common-gate （CG） topology to achieve wideband input matching and low noise figure （NF）. Inductive series-peaking is used for the LNA to obtain broadband flat gain in the whole 3.1-10.6 GHz band. Designed in 0.18 um CMOS technology, the LNA achieves an NF of 3.1-4.7 dB, an Sll of less than -10 dB, an S21 of 10.3 dB with ±0.4 dB fluctuation, and an input 3rd interception point （IIP3） of -5.1 dBm, while the current consumption is only 4.8 mA from a 1.8 V power supply. The chip area of the LNA is 1×0.94 mm^2.     

一种新颖的低噪声放大器的噪声优化方法

This paper proposes a novel noise optimization technique.The technique gives analytical formulae for the noise performance of inductively degenerated CMOS low noise amplifier（LNA）circuits with an ideal gate inductor for a fixed bias voltage and nonideal gate inductor for a fixed power dissipation,respectively,by mathematical analysis and reasonable approximation methods.LNA circuits with required noise figure can be designed effectively and rapidly just by using hand calculations of the proposed formulae.We design a 1.8 GHz LNA in a TSMC 0.25 μm CMOS process.The measured results show a noise figure of 1.6 dB with a forward gain of 14.4 dB at a power consumption of 5 mW,demonstrating that the designed LNA circuits can achieve low noise figure levels at low power dissipation.     

A wideband RF amplifier for satellite tuners

This paper presents the design and measured performance of a wideband amplifier for a direct conversion satellite tuner.It is composed of a wideband low noise amplifier(LNA) and a two-stage RF variable gain amplifier(VGA) with linear gain in dB and temperature compensation schemes.To meet the system linearity requirement, an improved distortion compensation technique and a bypass mode are applied on the LNA to deal with the large input signal.Wideband matching is achieved by resistive feedback and an off-chip LC-ladder matching network.A large gain control range(over 80 dB) is achieved by the VGA with process voltage and temperature compensation and dB linearization.In total,the amplifier consumes up to 26 mA current from a 3.3 V power supply. It is fabricated in a 0.35-μm SiGe BiCMOS technology and occupies a silicon area of 0.25 mm~2.     

一种基于低中频接收相位选择发射结构的工作在2.4GHz面向WPAN应用的超低功耗收发机

This paper presents a 2.4 GHz CMOS transceiver for the wireless personal area network （WPAN） inte- grated in 0.18/zm CMOS technology. This transceiver adopts a low-IF receiver, a MUX based transmitter and a fast-setting fractional-N frequency synthesizer. For achieving low cost and low power consumption, an inductor- less receiver front-end, an adaptive analog baseband, a low power MUX and a current-reused phase-locked loop （PLL） have been proposed in this work. Measured results show that the receiver achieves-8 dBrn of lIP3 and 31 dB of image rejection. The transmitter delivers 0 dBm output power at a data rate of 2 Mbps. The current consumption is 7.2 mA in the receiving mode and 6.9 mA in the transmitting mode, respectively.     

Low power high gain gain-controlled LNA and mixer for GNSS receivers Wei Binbin(魏斌斌)1, Jiang Jinguang(江金光)1,2,3*

A low power high gain gain-controlled LNA ＋ mixer for GNSS receivers is reported. The high gain LNA is realized with a current source load. Its gain-controlled ability is achieved using a programmable bias circuit. Taking advantage of the high gain LNA, a high noise figure passive mixer is adopted. With the passive mixer, low power consumption and high voltage gain of the LNA ＋ mixer are achieved. To fully investigate the performance of this circuit, comparisons between a conventional LNA ＋ mixer, a previous low power LNA ＋ mixer, and the proposed LNA ＋ mixer are presented. The circuit is implemented in 0.18 #m mixed-signal CMOS technology. A 3.8 dB noise figure, an overall 45 dB converge gain and a 10 dB controlled gain range of the two stages are measured. The chip occupies 0.24 mm2 and consumes 2 mA current under 1.8 V supply.     

用于无采保流水线ADC的高速低功耗低失调动态比较器

A novel fully differential high speed high resolution low offset CMOS dynamic comparator has been implemented in the SMIC 0.18 μm process used for a sample-and-hold amplifier （SHA）-less pipelined analog-to-digital converters （ADC）. Based on the analysis and optimization between delay time and offset, an enhanced reset architecture with transmission gate was introduced to speed up the comparison and reset procedure. Four inputs with two cross coupled differential pairs, reconstituted bias circuit for tail current transistor and common centroid layouts make the comparator more robust against mismatch and process variations. The simulation results demonstrate that the proposed design achieves 1 mV sensitivity at 2.2 GHz sampling rate with a power consumption of 510 μW, while the mean offset voltage is equal to 10.244 mV.     

一种应用于无线传感器网络的低电压低功耗上混频器

This paper presents an up-conversion mixer for 2.4-2.4835 GHz wireless sensor networks （WSN） in 0.18 μm RF CMOS technology. It was based on a double-balanced Gilbert cell type, with two Gilbert cells having quadrature modulation applied. Current-reuse and cross positive feedback techniques were applied in the mixer to boost conversion gain; the current source stage was removed from the mixer to improve linearity. Measured results exhibited that under a 1 V power supply, the conversion gain was 5 dB, the input referred 1 dB compression point was -11 dBm and the IIP3 was -0.75 dBm, while it only consumed 1.4 mW.     

High power single mode 980 nm AIGalnAs/AIGaAs quantum well lasers with a very low threshold current

To achieve low threshold current as well as high single mode output power, a graded index separate confinement heterostructure （GRIN-SCH） A1GaInAs/A1GaAs quantum well laser with an optimized ridge wave- guide was fabricated. The threshold current was reduced to 8 mA. An output power of 76 mW was achieved at 100 mA current at room temperature, with a slope efficiency of 0.83 W/A and a horizon divergent angle of 6.3°. The maximum single mode output power of the device reached as high as 450 mW.     

90nm CMOS工艺低功耗20GHz比较器设计

A low power 20 GHz CMOS dynamic latched regeneration comparator for ultra-high-speed, low-power analog-to-digital converters （ADCs） is proposed. The time constant in both the tracking and regeneration phases of the latch are analyzed based on the small signal model. A dynamic source-common logic （SCL） topology is adopted in the master-slave latch to increase the tracking and regeneration speeds. Implemented in 90 nm CMOS technology, this comparator only occupies a die area of 65 × 150 μm^2 with a power dissipation of 14 mW from a 1.2 V power supply. The measurement results show that the comparator can work up to 20 GHz. Operating with an input frequency of 1 GHz, the circuit can oversample up to 20 Giga-sampling-per-second （GSps） with 5 bits resolution; while operating at Nyquist, the comparator can sample up to 20 GSps with 4 bits resolution. The comparator has been successfully used in a 20 GSps flash ADC and the circuit can be also used in other high speed applications.     

基于反熔丝结构的低成本嵌入式一次可编程4-kbit 存储器宏

A 4-kbit low-cost one-time programmable （OTP） memory macro for embedded applications is designed and implemented in a 0.18-μm standard CMOS process. The area of the proposed 1.5 transistor （1.5T） OTP cell is 2.13 μm2, which is a 49.3% size reduction compared to the previously reported cells. The 1.5T cell is fabricated and measured and shows a large programming window without any disturbance. A novel high voltage switch （HVSW） circuit is also proposed to make sure the OTP macro, implemented in a standard CMOS process, works reliably with the high program voltage. The OTP macro is embedded in negative radio frequency identification （RFID） tags. The full chip size, including the analog front-end, digital controller and the 4-kbit OTP macro, is 600 × 600 μm2. The 4-kbit OTP macro only consumes 200 × 260 μm^2. The measurement shows a 100% program yield by adjusting the program time and has obvious advantages in the core area and power consumption compared to the reported 3T and 2T OTP cores.     

大分子螯合剂在低压力低磨料条件下铜膜的化学机械抛光中的应用

The mechanism of the FA/O chelating agent in the process of chemical mechanical polishing （CMP） is introduced. CMP is carried on a φ300 mm copper film. The higher polishing rate and lower surface roughness are acquired due to the action of an FA/O chelating agent with an extremely strong chelating ability under the condition of low pressure and low abrasive concentration during the CMP process. According to the results of several kinds of additive interaction curves when the pressure is 13.78 kPa, flow rate is 150 mL/min, and the rotating speed is 55/60 rpm, it can be demonstrated that the FA/O chelating agent plays important role during the CMP process.     

一种用于数字助听器SoC的高性能低功耗、可配置自动增益控制环路

A low-power,configurable auto-gain control loop for a digital hearing aid system on a chip(SoC) is presented.By adopting a mixed-signal feedback control structure and peak detection and judgment,it can work in automatic gain or variable gain control modes through a digital signal processing unit.A noise-reduction and dynamic range(DR) improvement technique is also used to ensure the DR of the circuit in a low-voltage supply.The circuit is implemented in an SMIC 0.13 μm 1P8M CMOS process.The measurement results show that in a 1 V power supply,1.6 kHz input frequency and 200 mVp-p,the SFDR is 74.3 dB,the THD is 66.1 dB,and the total power is 89 μW,meeting the application requirements of hearing aid SoCs.