工艺条件对Ni/Al2O3和Ni/CeO2-Al2O3催化剂在甲烷自热重整制氢反应中催化性能的影响

采用共沉淀法制备γ-Al₂O₃载体和不同Ce添加量的CeO₂-Al₂O₃载体,然后用浸渍法制备Ni负载质量分数10%的Ni/γ-Al₂O₃和Ni/CeO₂-Al₂O₃催化剂。在固定床微反装置中考察了反应温度、原料气配比和CH₄空速等工艺条件对Ni/γ-Al₂O₃和Ni/Ce₃₀Al₇₀O_δ催化剂在甲烷自热重整制氢反应中催化性能的影响。结果表明,添加Ce的催化剂催化性能有较大提高,在Ni/Ce₃₀Al₇₀O_δ催化剂上,反应温度750 ℃时, CH₄转化率94.3％,与Ni/Al₂O₃催化剂相比,提高20％。Ni/γ-Al₂O₃和Ni/CeO₂-Al₂O₃催化剂的CH₄转化率均随反应温度的升高而增大。原料气中n(O₂)∶n(CH₄)和n(H₂O)∶n(CH₄)的增加均能提高各催化剂的CH₄转化率。但n(O₂)∶n(CH₄)和n(H₂O)∶n(CH₄)的变化对各催化剂的催化性能的影响不同。随着n(O₂)∶n(CH₄)的增大,产物中n（H₂）∶n（CO）降低,n（CO₂）∶n(CO＋CO₂)升高;而n(H₂O)∶n(CH₄)增大时,产物中n（H₂）∶n（CO）和n（CO₂）∶n(CO＋CO₂)均升高。随着CH₄空速的增加,Ni/Al₂O₃催化剂上CH₄转化率、n（H₂）∶n（CO）和n（CO₂）∶n(CO＋CO₂)均较大程度下降;而在Ni/Ce₃₀Al₇₀O_δ催化剂上,随着CH₄空速的增加,CH₄转化率、n（H₂）∶n（CO）和n(CO₂）∶n(CO＋CO₂)变化不大。     

天然气-煤共气化制备合成气热态模拟

天然气-煤共气化制备通用合成气技术是基于天然气蒸汽转化法和煤气化过程开发的新工艺，通过技术原理分析，可以直接制备出H₂/CO在1.0～2.0之间可调的粗合成气.应用移动床反应器进行热态模拟实验，主要研究了不同操作参数对火焰区温度及合成气有效成分(H₂＋CO)和H₂/CO的影响.结果表明：天然气与氧气在同一位置喷入反应器，控制喷吹参数H₂O/CH₄/O₂以及流量，在气化炉炉温不低于1000 ℃的条件下，煤或焦炭中挥发分基本裂解，可以直接制备出H₂/CO在1.0～2.0之间，有效成分大于90.0%，残留的CH₄小于2.0%的粗合成气.     

基于NiO载氧体的煤化学链燃烧实验

采用流化床反应器并以水蒸气作为气化-流化介质,研究了以NiO为载氧体在800～960℃内的煤化学链燃烧反应特性。实验结果表明,载氧体与煤气化产物在反应器温度高于900℃体现了高的反应活性。随着流化床反应器温度的提高,气体产物中CO₂的体积浓度(干基)呈单调递增;CO、H₂、CH₄的体积浓度(干基)呈单调递减;煤中碳转化为CO₂的比率逐渐递增,碳的残余率逐渐递减。反应器出口气体CO₂、CO、H₂、CH₄的生成率随反应时间呈单峰特性,H₂生成率的峰值远小于CO的峰值;且随反应器温度升高,CO₂生成率升高,CO、H₂、CH₄的生成率降低。反应温度高于900℃时,流化床反应器NiO载氧体煤化学链燃烧在9 min之内就基本完成,CO₂含量高于92%。     

6FDA型聚酰亚胺中气体溶解行为的分子模拟

用分子模拟方法对6FDA-durene、6FDA-pPDA及其共聚物6FDA-durene/pPDA的链间距及自由体积进行了模拟计算,结果与文献实验值一致;采用巨正则Monte Carlo(GCMC)方法模拟了O₂、N₂、CH₄和CO₂在聚酰亚胺中的溶解,计算结果表明：COMPASS力场能较准确地描述O₂、N₂和CH₄在聚酰亚胺中的吸附溶解,O₂、N₂、CH₄的溶解系数模拟结果与实验数据吻合较好。CO₂的溶解系数计算值与实验值偏差较大(约50％),主要原因可能在于模拟过程中未考虑体积溶胀效应以及COMPASS力场不能精确描述CO₂与—CF₃基团的相互作用。同一聚合物中,计算所得气体溶解系数的大小顺序为CO₂>CH₄>O₂>N₂,与气体凝聚性趋势一致,同种气体在6FDA型聚酰亚胺中的溶解系数与其自由体积分数变化趋势一致。3种聚合物对CO₂/CH₄的溶解选择性高于O₂/N₂,共聚物与均聚物相比,气体溶解选择性没有明显提高。     

Fe/C杂化炭膜的制备及其气体分离性能

将二茂铁作为有机添加剂引入炭膜前驱体聚酰亚胺,经高温热解制备了Fe/C杂化炭膜。考察了二茂铁的添加量对杂化炭膜气体渗透性能的影响。采用热重、红外、X射线衍射和透射电镜等分析方法对所制备的杂化炭膜进行了表征。结果表明,在前驱体中添加二茂铁能显著提高炭膜的气体渗透性能,随着添加量的增加,膜的气体渗透系数明显增加而分离系数则减小,当二茂铁添加量为15%时,对H₂、O₂、N₂、CO₂、CH₄等纯气体的渗透系数分别为2806、1039、266、31、8 barrer,对O₂/N₂、CO₂/N₂、CO₂/CH₄的分离系数分别为8.6、33.5、129.5。Fe/C杂化炭膜是基于“分子筛分”机理分离气体分子。     

煤在O2/CO2中燃烧的Nox释放规律

利用一维沉降炉,对3种煤在O₂/CO₂和空气两种气氛下燃烧NO_x析出特性进行了比较,分析了炉膛温度、过量空气系数对NO_x生成量的影响,并对O₂/CO₂气氛下NO_x的生成和破坏机理进行了分析.研究发现两种气氛下NO_x都有一个峰值出现,挥发分含量高的煤种峰值靠前, 挥发分含量低的煤种峰值靠后,O₂/CO₂条件下,峰值出现较空气条件下提前且有所下降;空气条件下NO_x的生成量随温度提高较快地增加,而O₂/CO₂气氛中NO_x的生成量随温度变化比较缓慢;在两种气氛下NO_x的峰值均随过量空气系数的增加而增加,高挥发分煤在O₂/CO₂气氛下NO_x峰值低于空气条件下峰值,而低挥发分煤则受影响较小.     

硅橡胶/陶瓷复合膜反应器中CO2合成甲醇(Ⅲ)过程实验研究

对在由硅橡胶 /陶瓷复合膜所构成的膜反应器中进行的CO₂ 加氢合成甲醇的复杂反应体系CO₂ +3H₂=CH₃ OH +H₂ O与CO₂ +H₂=CO +H₂ O开展实验研究 .考察了硅橡胶 /陶瓷复合膜在合成含氧化合物反应过程中的作用 ,并讨论了CO₂ 与H₂ 合成甲醇反应的膜反应过程参数对反应行为的影响 ,对部分理论分析结果进行验证 .在实验条件下 ,CO₂ 合成甲醇复杂反应体系中的主反应转化率较传统的固定床反应器提高了 2 2 %     

α-纤维素膜气体分离性能

制备了α-纤维素膜并对其气体分离性能进行了研究.测定了水溶胀下，CO₂、H₂、CH₄、N₂、O₂等气体在α-纤维素膜内的气体渗透速率.通过比较研究醋酸纤维素膜、苯甲酰化纤维素膜和聚砜膜在干态和湿态下的气体渗透性能，揭示了水对α-纤维素膜气体渗透性能的作用规律.     

生物质超临界气化制氢产物高压吸收法分离的气液相平衡分析

通过高压吸收法可以将生物质超临界水气化制氢的气体产物中的CO₂与H₂分离.基于修正的UNIFAC模型、SRK状态方程以及MHV2混合规则，建立了生物质超临界气化制氢产物高压吸收法分离的气液相平衡的计算模型，讨论了CO₂与H₂分离过程中压力和温度等参数对分离效果的影响.计算结果表明：随着分离器中压力的升高，气相产物中H2的摩尔分数增加，CO₂摩尔分数迅速下降，气相中H₂的收率不断降低；随着温度升高，气相产物中H₂的摩尔分数减小，CO₂摩尔分数上升，气相中H₂的收率增加；然而，高压吸收的方法不能将气体产物中的CO、CH₄、C₂H₄、C₂H₆与H₂分离.     

O2/CO2气氛下煤燃烧SO2/NO析出特性

在水平管式炉上研究了O₂浓度、CO₂浓度、温度及石灰石添加等各参数对O₂/CO₂气氛下徐州烟煤和龙岩无烟煤燃烧过程中SO₂/NO排放特性的影响。结果发现,O₂/CO₂气氛下,烟煤和无烟煤燃烧SO₂/NO的析出规律与空气气氛下不同,同等O₂浓度下析出量比空气气氛下小。O₂/CO₂气氛下,随着O₂浓度的提高,烟煤和无烟煤SO₂/NO排放量均增大;随着CO₂浓度的升高, SO₂/NO排放量均减小。O₂/CO₂气氛下,石灰石添加对SO₂排放的抑制作用低于空气气氛下;石灰石添加对NO的排放有一定减排作用。对煤灰的元素分析显示O₂/CO₂燃烧对SO₂的抑制主要是由于煤灰的自固硫能力增强,而对NO的减排作用则是促进燃料N向其他含N气体的转换。     

移动床煤与天然气共气化制备合成气的工艺技术

煤与天然气共气化是基于天然气蒸汽转化和煤气化工艺耦合的一种新工艺.阐述了煤与天然气共气化制合成气的技术原理.实验研究表明合成气最佳出口温度为1000 ℃,氧气、水蒸气和天然气在同一位置进入反应器能有效降低火焰区温度;理论计算得到的合成气有效气体浓度（CO+H₂）大于95%.实验研究和理论计算结果都表明,煤与天然气共气化可以直接得到H₂/CO在1.0～1.5之间可以调节的合成气.     

煤的表面电位与表面官能团间的关系

测定了5种不同变质程度的典型中国动力煤在不同pH值的水介质中的ζ电位和用H₂O₂氧化后各煤种ζ电位的变化,得到了ζ电位等电点pH值;用FTIR定量表征了与煤表面电位有关的官能团以及被H₂O₂氧化后的变化;通过对模型化合物的ZINDO量子化学理论计算,得到了H⁺ 在煤表面的吸附能、相关化学键的键级、键长和净电荷分布.综合分析实验和计算的结果,确认了在水体系中煤的表面电荷为负电荷;煤的ζ电位等电点随煤化程度的提高有规律地升高;与煤表面ζ电位密切相关的负电性官能团主要是—OH基团;原煤经H₂O₂氧化后,—OH、和—COOH等官能团增多,煤表面负电性增加;H⁺在煤表面发生化学吸附,吸附能随着煤化程度的增加而增加.     

Hydrogen production from coal by separating carbon dioxide during gasification

Hydrogen generation during the reaction of a coal/CaO mixture with high pressure steam was investigated using a flow-type reactor. Coal, CaO and CO reactions with steam, and CO₂ absorption by Ca(OH)₂ or CaO occurred simultaneously in the experiment. It was found that H₂ was the primary resultant gas, comprising about 85% of the reaction products. CO₂ was fixed into CaCO₃ and CO was completely converted to H₂. Pyrolysis of the coal/CaO mixture carried out in N₂ was also examined. The pyrolysis gases were compared with gases produced by general coal pyrolysis. While general coal pyrolysis produced about 14.7% H₂, 50.5% CH₄, 12.0% CO and 12.0% CO₂, the gases produced from coal/CaO mixture pyrolysis were 84.8% H₂, 9.6% CH₄, 1.6% CO₂ and 1.1% CO.     

热分解气氛对流化床煤热解制油的影响

在循环流化床锅炉上耦合流化床热解反应器既可提供电力又副产热解油,明显提高煤的利用价值。在这个过程中,热解反应器通常利用自身产生的热解气作为流化介质。本文考察了模拟热解气反应气氛对流化床煤热解拔头制取热解油产率的影响,并利用TG-FTIR分析了焦油官能团组成及随TG温度的变化。针对锅炉用烟煤的实验结果表明：采用热解气作为反应气氛时焦油产率最大,相对无水无灰基煤达13%。反应气氛中H₂和CO₂的存在不利于焦油生成,但CO 和CH₄的加入提高了焦油产率;H₂的加入有利于焦油中酚羟基、羧基类化合物生成,同时也促进了脂肪族化合物的裂解;CH₄的存在可以提高焦油中单环芳烃、脂肪族及酚羟基类化合物的含量。     

Ignition behaviour of different rank coals in an entrained flow reactor

An experimental study to determine the temperature and mechanism of coal ignition was carried out by using an entrained flow reactor (EFR) at relatively high coal feed rates (0.5 g min⁻¹). Seven coals ranging in rank from subbituminous to semianthracite, were tested and the evolved gases (O₂, CO, CO₂, NO) were measured continuously. The ignition temperature was evaluated from the gas evolution profiles, and it was found to be inversely correlated to the reactivity of the coal, as reflected by the increasing values of the ignition temperature in the sequence: subbituminous, high volatile bituminous, low volatile bituminous and semianthracite coals. The mechanism of ignition varied from a heterogeneous mechanism for subbituminous, low volatile bituminous and semianthracite coals, to a homogeneous mechanism for high volatile bituminous coals. A thermogravimetric analyser (TGA) was also used to evaluate coal ignition behaviour. Both methods, TGA and EFR, were in agreement as regards the mechanism of coal ignition. From the SEM micrographs of the coal particles retrieved from the cyclone, it was possible to observe the external appearance of the particles before, during and after ignition. The micrographs confirmed the mechanism deduced from the gas profiles.     

Zeolite NaY-supported gold complexes prepared from Au(CH3)2(C5H7O2): reactivity with carbon monoxide

Mononuclear gold complexes in zeolite NaY were synthesized from initially physisorbed Au(CH₃)₂(C₅H₇O₂), and their reactions with CO in a flow system at 298 K and 760 Torr were investigated by infrared (IR) spectroscopy and mass spectral analysis of the effluent gases. CH₄ and CO₂ were formed as CO flowed through the sample either steadily or as successive pulses. The results are consistent with the inferences that (a) CO reacted with the supported gold to form gold carbonyls, (b) CH₄ formed by reaction of methyl groups on gold with traces of H₂O or hydroxyl groups on the zeolite and (c) CO on cationic gold reacted with traces of O₂ and/or H₂O to form CO₂. In samples treated in steadily flowing CO, cationic gold was reduced to zerovalent gold, but the cationic gold in samples exposed to CO pulses was not reduced to zerovalent gold, although CO₂ formed. Thus, CO adsorbed on cationic gold reacts to give CO₂ in the absence of zerovalent gold, consistent with the inference that gold catalysts for CO oxidation need not contain zerovalent gold.     

Ignition characteristics of coal blends in an entrained flow furnace

Ignition tests were carried out on blends of three coals of different rank - subbituminous, high volatile and low volatile bituminous - in two entrained flow reactors. The ignition temperatures were determined from the gas evolution profiles (CO, CO₂, NO, O₂), while the mechanism of ignition was elucidated from these profiles and corroborated by high-speed video recording. Under the experimental conditions of high carbon loading, clear interactive effects were observed for all the blends. Ignition of the lower rank coals (subbituminous, high volatile bituminous) enhanced the ignition of the higher rank coal (low volatile bituminous) in the blends. The ignition temperatures of the blends of the low rank coals (subbituminous-high volatile bituminous) were additive. However, for the rest of the blends the ignition temperatures were always closer to the lower rank coal in the blend.