Microstructure and ablation behavior of SiC coated C/C–SiC–ZrC composites prepared by a hybrid infiltration process

In this study, C/C–SiC–ZrC composites coated with SiC were prepared by precursor infiltration pyrolysis combined with reactive melt infiltration. The pyrolysis behavior of the hybrid precursor was investigated using thermal gravimetric analysis-differential scanning calorimetry, X-ray diffraction, and scanning electron microscopy techniques. The microstructure and ablation behavior of the composites were also investigated. The results indicate that the composites exhibit an interesting structure, wherein a ceramic coating composed of SiC and a small quantity of ZrC covers the exterior of the composites, and the SiC–ZrC hybrid ceramics are partially embedded in the matrix pores and distributed around the carbon fibers as well. The composites exhibit good ablation resistance with a surface temperature of over 2300 °C during ablation. After ablation for 120 s, the mass and linear ablation rates of the composites are 0.0026 g/s and 0.0037 mm/s, respectively. The great ablation resistance of the composites is attributed to the formation of a continuous phase of molten SiO₂ containing SiC and ZrO₂, which seals the pores of the composites during ablation.     

Preparation and ablation properties of SiC nanowire-reinforced ZrC–SiC coating-matrix integrated C/C composites

A modification of the precursor infiltration pyrolysis (PIP) method was explored to prepare the integrated doped ceramic matrix and coating by the added SiC nanowires layer and shape-stabilization process. The epitaxial layer of SiC nanowires provided surficial attachments for the precursor. And the shape-stabilization process aggregated loose ceramic particles into a coating. Then the SiC nanowire-reinforced ZrC–SiC coating-matrix integrated C/C (S/SZ-CZ/C) composite was simply prepared by the modified PIP method. The bonding strength between the coating and matrix of the S/SZ-CZ/C composite was improved. Through the ablation test, the mass and linear ablation rate of the S/SZ-CZ/C composite were 0.46 mg/s and 0.67 μm/s, which were 60.34 % and 74.91 % lower than those of the SiC nanowire-reinforced C/C–ZrC (S/CZ/C) composite, respectively. The integration of the coating and matrix enabled the formation of a continuous oxide layer of molten SiO₂ and ZrO₂ in the ablation process, which helped to block the oxygen and heat during the ablation test. Thus the ablation resistance of the materials was systematically and effectively improved.     

Ablation mechanism of C/C–SiC and C/C–SiC–ZrC composites in hypersonic oxygen-enriched environment

In this study, C/C–SiC and C/C–SiC–ZrC composites were prepared via chemical vapor infiltration and polymer infiltration pyrolysis, and the ablation mechanism under hypersonic oxygen-rich environmental conditions was investigated. The C/C–SiC composites demonstrate an excellent ablation resistance in a hypersonic oxygen-rich environment with a relatively low temperature and speed of approximately 1800 K and 1100 m/s, respectively. It is only in the ablation center area with higher temperatures that a certain degree of thermochemical ablation was observed. The mass and linear ablation rates of C/C–SiC composites (0.027 g/s and 0.117 mm/s, respectively) showed a significant increase in a hypersonic oxygen-rich environment with a temperature and velocity of approximately 2050 K and 2000 m/s, respectively. The high-temperature ablation resistance of ZrC-modified C/C–SiC–ZrC composites improved significantly. However, the ZrC ceramic component had a considerable impact on the ablation resistance of the material. The structural integrity of C/C–20SiC–30ZrC composites was relatively high in hypersonic oxygen-rich environments with a jet temperature and velocity of 2050 K and 2000 m/s, respectively, and mass and linear ablation rates were 0.012 g/s and 0.015 mm/s, respectively. When the ZrC content increased by 40%, the ablation resistance of the composite reduced significantly, whereas the mass and linear ablation rates increased to 0.043 g/s and 0.130 mm/s, respectively.     

Cyclic ablation behavior of C/C–ZrC–SiC composites under oxyacetylene torch

Cyclic ablation behavior of C/C–ZrC–SiC composites prepared by precursor infiltration and pyrolysis process was studied using oxyacetylene torch. After repeated 30 s ablation for four times, the composites exhibited better ablation properties than those under single ablation for 120 s because of the lower surface temperature, and their linear and mass ablation rates were −3×10^–4 mm/s and −2.29×10^–3 g/s, respectively. A continuous ZrO₂–SiO₂ layer formed on the surface of center ablation region and acted as an effective barrier to the transfer of heat and oxidative gases into the inner material. Thermal stress induced by repeated impact of oxyacetylene led to some cracks on the ZrO₂–SiO₂ layer; however its destructive power was weaker than that of higher temperature. Stick like silica as grown silica nanowires were generated in the transition ablation region due to the evaporation of silicon oxide at appropriate temperature.     

Effects of porous C/C density on the densification behavior and ablation property of C/C–ZrC–SiC composites

C/C–ZrC–SiC composites were prepared by precursor infiltration and pyrolysis process using a mixture solution of organic zirconium-containing polymer and polycarbosilane as precursors. Porous carbon/carbon (C/C) composites with density of 0.92, 1.21 and 1.40 g/cm³ were used as preforms, and the effects of porous C/C density on the densification behavior and ablation resistance of C/C–ZrC–SiC composites were investigated. The results show that the C/C preforms with a lower density have a faster weight gain, and the obtained C/C–ZrC–SiC composites own higher bulk density and open porosity. The composites fabricated from the C/C preforms with a density of 1.21 g/cm³ exhibit better ablation resistance with a surface temperature of over 2400 °C during ablation. After ablation for 120 s, the linear and mass ablation rates of the composites are as low as 1.02 × 10⁻³ mm/s and −4.01 × 10⁻⁴ g/s, respectively, and the formation of a dense and continuous coating of molten ZrO₂ solid solution is the reason for their great ablation resistance.     

Effect of Al addition on the single and cyclic ablation properties of C/C–SiC composites

This article focuses on the damage behavior and mechanism of aluminum addition on reactive melt infiltrated C/C–SiC composites in single and cyclic ablation environments. Plasma ablation tests were performed on C/C–SiC composites containing 20 wt % and 40 wt % aluminum respectively. Coupled with TMA, XRD, SEM and EDS, the results showed that composites with 40 wt % Al had better ablation resistance during the cyclic ablation, while the composites with 20 wt % Al had excellent ablation damage resistance during a single ablation. This difference was due to higher number of microcracks formed inside the composites containing 40 wt % Al than 20 wt % Al, the lower specimen surface temperature during ablation, and the thermal stresses can be released by pore crack expansion during gas reciprocal loading. While in the single continuous loading of gas, the 20 wt % Al composite formed a protective oxide layer with smaller pores and fewer gas and oxygen entry channels, resulting in good resistance to ablation.     

Preparation and formation mechanism of C/C–SiC composites using polymer-Si slurry reactive melt infiltration

This study proposes a polymer-metal slurry reactive melt infiltration (RMI) method to overcome the limitations of conventional RMI in modifying irregular geometric carbon–carbon (C/C) preforms. Herein, polycarbosilane (PCS), polysiloxane, phenol-formaldehyde, and epoxy resin, which were introduced to prepare slurries with Si powder, and subsequently used to modify cylindrical C/C preforms into C/C–SiC composites. Results show that the PCS–Si slurry has the best RMI capability, by which, a cylindrical C/C preform (1.35 g·cm⁻³) was modified successfully to into a dense C/C–SiC composite (1.92 g·cm⁻³). PCS plays a vital role in fixing the coating to prevent it from falling off the surface of the C/C preform in PCS–Si slurry RMI. Both of the degree of densification and flexural strength of the C/C–SiC composites increase with an increase in the thickness of the PCS–Si slurry coating. The overreaction of the PCS–Si slurry RMI was effectively suppressed because the content of Si powder is reasonably controlled in the PCS–Si slurry coating. Moreover, nozzle-shaped C/C composites were successfully modified into a C/C–SiC composite for the first time using PCS–Si slurry RMI.     

Microstructure and ablation behavior of carbon/carbon composites infiltrated with Zr–Ti

Carbon/carbon(C/C) composites infiltrated with Zr–Ti were prepared by chemical vapor infiltration and reactive melt infiltration. Their microstructure and ablation behavior at different temperatures and time were investigated. The results show that C/C composites infiltrated with Zr–Ti have good interface cohesion between carbon fibers, pyrocarbon and carbide. Compared with C/C composites and C/C–ZrC composites, the synthesized sample with Zr_0.83Ti_0.17C_0.92 and Ti_0.82Zr_0.18C_0.92 exhibits better ablation resistance at 2500 °C due to the newly formed protective layer composed of ZrTiO₂ pinned by ZrO₂ grains after ablation. The ablation resistance of the sample with Zr_0.57Ti_0.43C_1.01 increased gradually with the decrease of temperature from 3000 °C to 2000 °C, whereas the ablation resistance of the sample with Zr_0.83Ti_0.17C_0.92 and Ti_0.82Zr_0.18C_0.92 first increased obviously and then decreased slightly. In addition, the work indicates that surplus particles or liquid phases of oxides cannot protect the matrix, and that the liquid oxides may even cause severe ablation. Furthermore, a protective layer of oxides tends to be formed with the increase of ablation time.     

Friction and wear properties of C/C–SiC braking composites

Two series of C/C–SiC composites were fabricated via precursor infiltration pyrolysis (PIP) and chemical vapor infiltration (CVI) using porous C/C composites with different original densities as preforms, respectively. The tribological characteristics of C/C–SiC braking composites were investigated by means of MM-1000 type of friction testing machine. The friction and wear behaviors of the two series of composites were compared and the factors that influence the friction and wear properties of C/C–SiC composites were discussed. Results show that the friction and wear properties relate close-knit to the content of SiC and porosity. As the original preform density increasing, the content of SiC and porosity decrease, and then the friction coefficient increases obviously, the braking time and the wear rate both decrease. Preparation techniques play an important role in the tribological properties of C/C–SiC composites. Compared with PIP process, the samples from CVI have a little higher friction coefficient, shorter braking time and higher wear rate.     

Microstructure and tribological properties of PIP-SiC modified C/C–SiC brake materials

A combination method of precursor infiltration and pyrolysis (PIP), chemical vapor infiltration (CVI) and liquid silicon infiltration (LSI) was proposed to prepare PIP-SiC modified C/C–SiC brake materials. The SiC ceramic matrix pyrolyzed by polymethysilane (PMS) homogeneously dispersed in the fiber bundles region, which improved the plough resistance of local C/C region and the wear resistance of C/C–SiC brake materials. When the braking speed rises to 28 m/s, the fluctuation range of friction coefficient was limited to 0.026. The linear wear rate of the as-prepared composites was could be ~50% less than that of C/C–SiC, when the braking speed was above 15 m/s (for instance, the wear rate of 1.02 μm/(side·cycle) at 28 m/s less than 2.02 μm/(side·cycle) of traditional C/C– SiC). The fading ratio D of CoF under wet conditions was ~11%. The results showed that introducing PIP-SiC could stabilize the braking process and effectively prolong the service life of C/C–SiC brake materials.     

Microstructure characterization and compressive performance of 3D needle-punched C/C–SiC composites fabricated by gaseous silicon infiltration

3D needle-punched C/C-SiC composites were fabricated from carbon fiber reinforced carbon (C/C) preforms, with densities of 1.05?g/cm³ and 1.28?g/cm³, by the gaseous silicon infiltration (GSI) method at fabrication temperatures from 1500?°C to 1800?°C. The compressive strengths and elastic moduli in transverse direction are larger than those measured under longitudinal compression except that samples fabricated from 1.28?g/cm³ density exhibit lower elastic moduli in transverse direction than in longitudinal direction. The compressive strength and modulus increase with fabrication temperature at 1500?°C and 1600?°C, and then decrease with higher fabrication temperature. Samples fabricated from the lower density C/C preforms have greater compressive strength and modulus. X-ray tomography was applied before and after the mechanical tests to characterize the microstructure and damage patterns, and the results indicated that for C/C-SiC composites fabricated at 1700?°C from 1.28?g/cm³ density C/C preform the matrix has a volume fraction (vol%) of 36.9%, and the initial intra-bundle cracks (0.6?vol%) display a space crossing structure while the inter-bundle pores (6.0?vol%) are special irregularly distributed.     

Ablation behavior and mechanism of C/C–ZrC–SiC composites under an oxyacetylene torch at 3000 °C

C/C–ZrC–SiC composites with continuous ZrC–SiC ceramic matrix were prepared by a multistep technique of precursor infiltration and pyrolysis process. Ablation properties of the composites were tested under an oxyacetylene flame at 3000 °C for 120 s. The results show that the linear ablation rate of the composites was about an order lower than that of pure C/C and C/C–SiC composites as comparisons, and the mass of the C/C–ZrC–SiC composites increased after ablation. Three concentric ring regions with different coatings appeared on the surface of the ablated C/C–ZrC–SiC composites: (i) brim ablation region covered by a coating with layered structure including SiO₂ outer layer and ZrO₂–SiO₂ inner layer; (ii) transition ablation region, and (iii) center ablation region with molten ZrO₂ coating. Presence of these coatings which acted as an effective oxygen and heat barrier is the reason for the great ablation resistance of the composites.     

Microstructure and properties of ablative C/ZrC–SiC composites prepared by reactive melt infiltration of zirconium and vapour silicon infiltration

C/ZrC-SiC composites with a density of 3.09 g/cm³ and a porosity of 4.8% were prepared by reactive melt infiltration and vapour silicon infiltration. The flexural strength and modulus were 235 MPa and 18.3 GPa, respectively, and the fracture toughness was 7.0 MPa m^1/2. The formation of SiC and ZrSi₂ during vapour silicon infiltration, at the residual cracks and pores in the C/ZrC, enhanced the interface strength and its mechanical properties. The high flexural strength (223 MPa, c. 95% of the original value) after oxidation at 1600 °C for 10 min indicated the excellent oxidation resistance of the composites after vapour silicon infiltration. The mass loss and linear recession rate of the composites were 0.0071 g/s and 0.0047 mm/s, respectively and a fine ablation morphology was obtained.     

Failure mechanism and tensile constitutive model of the unidirectional-laminated Cf/SiC–Al composites

The unidirectional-laminated C_f/SiC–Al composites were prepared by using precursor infiltration and pyrolysis (PIP) and vacuum pressure infiltration processes. Bulk density and open porosity of as-prepared C_f/SiC–Al composites were characterized which showed a large number of pores in the unidirectional-laminated carbon fiber preform were filled with SiC and Aluminum alloy matrix. The uniaxial tensile tests were conducted to study the mechanical properties. The fracture surface and cross-section of tensile specimens were characterized to clarify the failure mechanism. The results showed that under the action of load, the propagation of microcracks in matrix led to interface debonding, fiber fracture and pull-out. According to the stress-displacement behavior and analysis of damage process, the prediction formulas of the linear proportional limit stress value and the tensile strength value were proposed. A bilinear constitutive model was established based on the assumption of the damage process which well characterized constitutive response of the composites.     

Effects of density and heat treatment of C/C preforms on microstructure and mechanical properties of C/C–SiC composites

Twill multidirectional carbon-fiber-reinforced carbon and silicon carbide composites (i.e., C/C–SiC) were prepared via chemical vapor infiltration combined with reactive melt infiltration process. The effect of heat treatment (HT) on the microstructure and mechanical properties of C/C–SiC composites obtained by C/C preforms with different densities was thoroughly investigated. The results show that as the bulk density of C/C preforms increases, the thickness of the pyrolytic carbon (PyC) layer increases and open pore size distribution narrows, making the bulk density and residual silicon content of C/C–SiC composites decrease. Moreover, the flexural strength and tensile strength of the C/C–SiC composites were improved, which can be attributed to the increased thickness of the PyC layer. The compressive strength reduces due to the decrease of the ceramic phase content. HT improves the graphitization degree of PyC, which reduces the silicon–carbon reaction rate and thereby the content of the SiC phase. HT induces microcracks and porosity but not obviously affects the mechanical properties of C/C–SiC composites. However, the negative impact of HT can be compensated by the increased density of the C/C preforms.     

Microstructure and tribological behaviors of C/C–BN composites fabricated by chemical vapor infiltration

In this paper carbon fiber reinforced carbon–boron nitride binary matrix composites (C/C–BN) were prepared by chemical vapor infiltration (CVI). The infiltration of BN in the CVI process was controlled by the diffusion of BCl₃, and BN matrix was distributed homogeneously in the porous carbon fiber reinforced carbon matrix composites (C/C) due to the good infiltration ability of BN. The as-received C/C–BN composites were composed of 92 vol% C and 8 vol% BN. Both the friction coefficient and wear rate of C/C composites decreased significantly by the incorporation of BN. After heat-treated at 1600 °C, the interlayer spacing of CVI BN decreased to 3.36 Å, and CVI BN with high crystalline degree displayed the excellent lubricating effect, leading to the decrease of friction coefficient and wear rate. The improvement of the tribological properties also was partially attributed to the improved oxidation resistance and the formation of friction film by the incorporation of BN matrix.     

Microstructure and mechanical performance evolution of C/C–ZrC composites exposed to oxyacetylene flame

C/C–ZrC composites were prepared by isothermal chemical vapor infiltration (ICVI) combined with reactive melt infiltration (RMI). The ablation behavior of the C/C–ZrC was investigated using an oxyacetylene flame. The effect of ablation time on the microstructure and mechanical property evolution of the composite was studied. The results showed that as the ablation time prolonged, the linear and mass ablation rates of the composite increased firstly and then stabilized. After 15 s ablation, the flexural strength and modulus of the C/C–ZrC were interestingly increased by 141.8% and 40.9%, which reached 138.42 MPa and 6.45 GPa, respectively. During ablation, the preferential oxidation effect of ZrC could mitigate the oxidation of pyrolytic carbon (PyC) and carbon fibers, and the volume change induced by the ZrC →ZrO₂ phase transformation could weaken its bonding with PyC, which was beneficial for releasing the internal residual stresses of the C/C–ZrC and then contributed to the mechanical performance improvement.     

Long-term oxidation and ablation behavior of Cf/ZrB2–SiC composites at 1500, 2000, and 2200°C

Although C_f/ZrB₂–SiC composites prepared via direct ink writing combined with low-temperature hot-pressing were shown to exhibit high relative density, high preparation efficiency, and excellent flexural strength and fracture toughness in our previous work, their oxidation and ablation resistance at high and ultrahigh temperatures had not been investigated. In this work, the oxidation and ablation resistance of C_f/ZrB₂–SiC composites were evaluated via static oxidation at high temperature (1500°C) and oxyacetylene ablation at ultrahigh temperatures (2080 and 2270°C), respectively. The thickness of the oxide layer of the C_f/ZrB₂–SiC composites is <40 μm after oxidizing at 1500°C for 1 h. The C_f/ZrB₂–SiC composites exhibit non-ablative properties after oxyacetylene ablation at 2080 and 2270°C for >600 s, with mass ablation rates of 3.77 × 10⁻³ and 5.53 × 10⁻³ mg/(cm² s), and linear ablation rates of −4.5 × 10⁻⁴ and −5.8 × 10⁻⁴ mm/s, respectively. Upon an increase in the ablation temperature from 2080 to 2270°C, the thickness of the total oxide layer increases from 360 to 570 μm, and the carbon fibers remain intact in the unaffected region. Moreover, the oxidation and ablation process of C_f/ZrB₂–SiC at various temperatures was analyzed and discussed.     

Improved ablation resistance of C–C composites using zirconium diboride and boron carbide

Zirconium diboride and boron carbide particles were used to improve the ablation resistance of carbon–carbon (C–C) composites at high temperature (1500 °C). Our approach combines using a precursor to ZrB₂ and processing them with B₄C particles as filler material within the C–C composite. An oxyacetylene torch test facility was used to determine ablation rates for carbon black, B₄C, and ZrB₂–B₄C filled C–C composites from 800 to 1500 °C. Ablation rates decreased by 30% when C–C composites were filled with a combination of ZrB₂–B₄C particles over carbon black and B₄C filled C–C composites. We also investigated using a sol–gel precursor method as an alternative processing route to incorporate ZrB₂ particles within C–C composites. We successfully converted ZrB₂ particles within C–C composites at relatively low temperatures (1200 °C). Our ablation results suggest that a combination of ZrB₂–B₄C particles is effective in inhibiting the oxidation of C–C composites at temperatures greater than 1500 °C.     

Microstructure,interfacial characteristics,and wear performances of Cu–Fe–SiC cermet composites

The Cu–Fe metal-based ceramic grinding wheel material with SiC as abrasive was prepared by the powder metallurgy process of ball milling and hot pressing sintering. Cu–Fe–SiC cermets with Cu:Fe mass ratios of 4:1, 1:1, and 1:4 were designed by changing the composition of metal binder. The phase composition, microstructure, mechanical properties, and grinding properties of Cu–Fe–SiC cermets were systematically studied. The effect of Cu–Fe binder ratio on the microstructure and properties of cermets was analyzed. The results show that with the increase of Fe content, the density and hardness of cermets increase gradually, indicating that the mechanical properties are improved. Because the Fe in the adhesive can react with the abrasive SiC to form the reaction bonding interface, the Cu–80Fe–SiC cermets with higher Fe content have better adherence. The grinding test results of Cu–80Fe–SiC cermet show that the friction coefficient is .341, the surface roughness is 6.64 μm, the residual stresses parallel to the grinding direction are 353.3 MPa, and the residual stresses perpendicular to the grinding direction are 140.9 MPa. With the increase of Fe content, the wear mechanism changes from ploughing and cutting to friction.