Preliminary investigation of flash sintering of SiC

The feasibility of flash sintering a covalent ceramic, SiC, has been investigated for the first time. Flash sintering involves the application of an electrical potential difference across a powder compact during heating, which leads to sintering at low furnace temperatures in a few seconds and has only been demonstrated with ionic ceramics previously. Near-theoretical density was achieved using Al₂O₃ + Y₂O₃ sintering aids at a furnace temperature of only 1170 °C and in a time of 150 s. Specimen temperatures were significantly higher than the furnace temperature owing to Joule heating and consequently heat loss limited densification in the near surface region. It was not possible to reach high densities using “ABC” sintering aids (aluminium–boron–carbon) or pure SiC. The mechanisms involved and potential commercial advantages are briefly discussed.     

Flash sintering of 3YSZ/Al2O3-platelet composites

Preparation of 3YSZ/Al₂O₃-platelet composites always requires high temperature, long duration, and/or high pressure. Herein, 3YSZ/Al₂O₃-platelet composites are prepared at low temperature of 492°C-645°C in 30 seconds by flash sintering under the electric field of 300-800 V/cm. The influence of electric field and current limit on the densification and grain growth of composites is investigated. The onset temperature for flash sintering is determined by electric field, which is decreased with increasing the electric field. Under the constant electric field, the current limit has a great effect on the density and grain size of composite. The flash-sintered 3YSZ/Al₂O₃-platelet composites exhibit relatively high hardness and elastic modulus. Both Joule heating and defects generation are proposed to be responsible for the rapid densification in flash sintering. This work demonstrates the feasibility of employing the flash sintering to prepare ceramic composites with fine grain size.     

Flash-sintering of MnCo2O4 and its relation to phase stability

The flash-sintering behavior of manganese cobaltite spinel (MnCo₂O₄) is analyzed in the present work. It is shown that the MnCo₂O₄ is flash-sintered at 120–150 °C under 15.0–17.5 V cm⁻¹, which is substantially lower than the conventional-sintering temperatures of 1080 °C and more. We have also demonstrated that the flash-sintering is a transient phenomenon, where the power dissipation rises quickly at first and then results to Joule heating. The extent of sintering is confirmed through SEM, where a dense and pore-free morphology is observed for the well-sintered samples. The growth of secondary phase as a function of sintering temperature in both conventional and flash processes is monitored by XRD. Consistent changes in I–V curves observed at 200–700 °C, suggest that the rapid increase of the conductivity during flash-effect follows the hopping mechanism of usual conductivity phenomenon. On the basis of correlation between the conductivity, phase-stability and microstructure, a mechanism for flash-sintering has been proposed.     

Doping effect of divalent cations on sintering of polycrystalline yttria

The sintering behavior of Y₂O₃ doped with 1 mol% of Ca²⁺, Mg²⁺, Mn²⁺, Ni²⁺, Sr²⁺ or Zn²⁺ was investigated by pressureless sintering in air at a sintering temperature in the range 900–1600 °C. The sintering temperature required for full densification in Y₂O₃ was reduced by 100–400 °C by the cation doping, while undoped Y₂O₃ was densified at 1600 °C. The most effective dopant among the examined cations was Zn²⁺. The grain growth kinetics of undoped and cation-doped Y₂O₃ was described by the parabolic law. The grain boundary mobility of Y₂O₃ was accelerated by doping of the divalent cations. High-resolution transmission electron microscopy (HRTEM) observations and nano-probe X-ray energy dispersive spectroscopy (EDS) analyses confirmed that the dopant cations tended to segregate along the grain boundaries without forming amorphous layers. The improved sinterability of Y₂O₃ is probably related to the accelerated grain boundary diffusion owing to the grain boundary segregation of the dopant cations.     

Densification of nanocrystalline Y2O3 ceramic powder by spark plasma sintering

Nanocrystalline Y₂O₃ powders with 18 nm crystallite size were sintered using spark plasma sintering (SPS) at different conditions between 1100 and 1600 °C. Dense specimens were fabricated at 100 MPa and 1400 °C for 5 min duration. A maximum in density was observed at 1400 °C. The grain size continuously increased with the SPS temperature into the micrometer size range. The maximum in density arises from competition between densification and grain growth. Retarded densification above 1400 °C is associated with enhanced grain growth that resulted in residual pores within the grains. Analysis of the grain growth kinetics resulted in activation energy of 150 kJ mol^?1 and associated diffusion coefficients higher by 10³ than expected for Y³⁺ grain boundary diffusion. The enhanced diffusion may be explained by combined surface diffusion and particle coarsening during the heating up with grain boundary diffusion at the SPS temperature.     

The influence of MgO,Y2O3 and ZrO2 additions on densification and grain growth of submicrometre alumina sintered by SPS and HIP

Spark plasma sintering followed by hot isostatic pressing was applied for preparation of polycrystalline alumina with submicron grain size. The effect of additives known to influence both densification and grain growth of alumina, such as MgO, ZrO₂ and Y₂O₃ on microstructure development was studied. In the reference undoped alumina the SPS resulted in some microstructure refinement in comparison to conventionally sintered materials. Relative density >99% was achieved at temperatures >1200 °C, but high temperatures led to rapid grain growth. Addition of 500 ppm of MgO, ZrO₂ and Y₂O₃ led, under the same sintering conditions, to microstructure refinement, but inhibited densification. Doped materials with mean grain size <400 nm were prepared, but the relative density did not exceed 97.9%. Subsequent hot isostatic pressing (HIP) at 1200 and 1250 °C led to quick attainment of full density followed by rapid grain growth. The temperature of 1250 °C was required for complete densification of Y₂O₃ and ZrO₂-doped polycrystalline alumina by HIP (relative density >99.8%), and resulted in fully dense opaque materials with mean grain size<500 nm.     

Synthesis and characterization of dense and fine nickel ferrite ceramics through two-step sintering

Two-step sintering (TSS) has been employed in the current study to suppress the accelerated grain growth of NiFe₂O₄ nanopowder compacts in the final sintering stage. Experiments are conducted to determine the appropriate temperatures for each step. The temperature range from 1200 °C to 1300 °C is effective for the first-step sintering (T₁) due to its highest densification rate. The second-step sintering temperature (T₂) should be within the kinetic window, where grain boundary diffusion is maintained but grain boundary migration is suppressed. The grain sizes of high density (≥98% theoretical density) NiFe₂O₄ compacts produced by TSS are smaller than 700 nm, while that of those formed by CS are over 2.5 μm. The evidence indicates that the saturation magnetization of nearly full NiFe₂O₄ ceramics is independent of grain size and likewise high, with the corresponding values of approximately 54 emu/g. The Vickers hardness and fracture toughness both increase with the decrease of grain size and porosity.     

Mechanical and optical properties of spark plasma sintered transparent Y2O3 ceramics

Commercial Y₂O₃ nanopowder was used to fabricate transparent Y₂O₃ ceramics by spark plasma sintering under the pressure of 100 MPa for 20 min with the heating rate of 100 °C/min. The microstructures, mechanical and optical properties of the Y₂O₃ ceramics sintered at different temperatures were investigated in detail. Densification occurred up to a sintering temperature of 1500 °C, and above 1500 °C, rapid grain growth and pore growth occurred. The highest relative density of 99.58% and the minimum average grain size of 0.58±0.11 µm were obtained at 1500 °C. The flexural strength, hardness and fracture toughness of the optimal spark plasma sintered Y₂O₃ ceramic were 122 MPa, 7.60 GPa and 2.06 MPa.m^1/2, respectively. The Y₂O₃ ceramic sintered at 1500 °C had the in-line transmission of about 11–54% and 80% in the wavelength range of 400–800 nm and 3–5 µm, respectively.     

Flash‐sintering of magnesium aluminate spinel (MgAl2O4) ceramics

The sintering behavior of commercially available MgAl₂O₄ spinel was investigated under DC electric field in a range of 0 and 1000 V/cm. Flash‐sintering results in densification close to theoretical density at 1410°C under the DC field of 1000 V/cm, in comparison to the higher sintering temperature of 1650°C in case of conventional sintering. It was observed that the fields less than 750 V/cm had no significant effect on the densification behavior. An abrupt increase in power dissipation was observed corresponding to the occurrence of the flash event. A significant enhancement in grain size was observed in case of flash‐sintered dense spinel samples. The gradual increase in the specimen conductivity observed in the electric field‐assisted sintering (FAST) regime led to Joule heating within the specimen. The increased specimen temperature triggered further increment of current and Joule heating, resulting in the immediate densification.     

Suppression of grain growth in sub-micrometer alumina via two-step sintering method

Two-step sintering (TSS) was applied to suppress the accelerated grain growth of sub-micron (～150 nm) alumina powder. The application of an optimum TSS regime led to a remarkable decrease of grain size down to ～500 nm; while the grain size of the full-dense structures produced by conventional sintering ranged between 1 and 2 μm. To find how important the temperatures at sintering steps might be, several TSS regimes were conducted. The results showed that the temperatures at both sintering steps play vital roles in densification and grain growth of the alumina compacts. Based on the results, the optimum regime consisted of heating the green bodies up to 1250 °C (first step) and then holding at 1150 °C for more than 60 h (second step). This yielded the finest microstructure with no deterioration of the densification. Heating at 1300 °C (first step) and then at 1200 °C (second step) was not a successful procedure. Lowering the temperature of the second step down to 1100 °C resulted in exhaustion of the densification at 88% -theoretical density. A nearly full-dense structure with an average grain size of 850 nm was obtained when the temperature of the second step was increased to 1150 °C. Empirical results show that not only the first step temperature has to be high enough to reach a structure containing unstable pores, but the second sintering temperature must also be high enough to activate the densification mechanism without grain growth. This means that a considerable densification at the first step does not imply enough second-step densification.     

Spark plasma sintering of combustion-synthesized β-SiAlON powders

In this paper, the sintering behavior of β-Si_6−zAl_zO_zN_8−z (z=1) powder prepared by combustion synthesis (CS) was studied using spark plasma sintering (SPS). The CSed powder was ball milled for various durations from 0.5 to 20 h and was then sintered at different temperatures with heating rates varying from 30 °C/min to 200 °C/min. The effects of ball milling, sintering temperature, and heating rate on sinterability, final microstructure, and mechanical property were investigated. A long period of ball milling reduced the particle size and subsequently accelerated the sintering process. However, the fine powder was easily agglomerated to form secondary particles, which accordingly decreased the densification of the SPS product. The high sintering temperature accelerated the densification process, whereas the high heating rate reduced the grain growth and increased the relative density of the sintered product.     

Microwave sintering of AlN powder synthesized by a SHS method

Sintering of the AlN powder synthesized by a combustion synthesis method, which was developed recently by the present authors, was studied by using a microwave sintering technique. A single mode microwave cavity was used and an insulation package with a simple configuration was developed. A high sintering temperature (1900 °C or higher) and a stable and uniform heating were readily achieved. A temperature measurement technique using a thermocouple with extrapolation was established to obtain the sintering temperature. A percent theoretical density of 99.5% and a thermal conductivity of 186 W/m K were obtained for a specimen which was sintered at 1900 °C with a soaking time of 30 min and 3 wt.% of Y₂O₃ added. The effects of sintering aid (i.e., Y₂O₃) and sintering temperature on densification, microstructure and thermal conductivity of the sintered specimens were investigated.     

Analysis of reactions during sintering of CuO-doped 3Y-TZP nano-powder composites

3Y-TZP (yttria-doped tetragonal zirconia) and CuO nano powders were prepared by co-precipitation and copper oxalate complexation–precipitation techniques, respectively. During sintering of powder compacts (8 mol% CuO-doped 3Y-TZP) of this two-phase system several solid-state reactions clearly influence densification behaviour. These reactions were analysed by several techniques like XPS, DSC/TGA and high-temperature XRD. A strong dissolution of CuO in the 3Y-TZP matrix occurs below 600 °C, resulting in significant enrichment of CuO in a 3Y-TZP grain-boundary layer with a thickness of several nanometres. This “transient” liquid phase strongly enhances densification. Around 860 °C a solid-state reaction between CuO and yttria as segregated to the 3Y-TZP grain boundaries occurs, forming Y₂Cu₂O₅. This solid-state reaction induces the formation of the thermodynamic stable monoclinic zirconia phase. The formation of this solid phase also retards densification. Using this knowledge of microstructural development during sintering it was possible to obtain a dense nano–nano composite with a grain size of only 120 nm after sintering at 960 °C.     

Fabrication and properties of Y2O3 transparent ceramic by sintering aid combinations

Transparent Y₂O₃ ceramics were fabricated by the solid-state reaction and vacuum sintering method using La₂O₃, ZrO₂ and Al₂O₃ as sintering aids. The microstructure of the Y₂O₃ ceramics sintered from 1550 °C to 1800 °C for 8 h were analyzed by SEM. The sintering process of the Y₂O₃ transparent ceramics was optimized. The results showed that when the samples were sintered at 1800 °C for 8 h under vacuum, the average grain sizes of the ceramics were about 3.5 µm. Furthermore, the transmittance of Y₂O₃ ceramic sintered at 1800 °C for 8 h was 82.1% at the wavelength around the 1100 nm (1 mm thickness), which was close to its theoretical value. Moreover, the refractive index of the Y₂O₃ transparent ceramic in the temperature range from 30 °C to 400 °C were measured by the spectroscopic ellipsometry method.     

Microstructural evolution of nanocrystalline Al2O3 sintered at a high heating rate

Experimental sintering studies on Al₂O₃ powder (200 nm and 600 nm) were done at a heating rate of 1600 °C/min. The microstructural changes of specimens were examined and corresponding detailed data on the densification and grain size as a function of sintering time were presented. The grain-growth transition behavior during sintering was discussed. The results showed that the neck growth caused principally by surface diffusion could be negligible within 2 min. With subsequent increases of sintering time, grain growth promoted by grain boundary and lattice diffusion occurred.     

Novel amorphous precursor densification to transparent Nd:Y2O3 Ceramics

A novel approach of neodymium ion doped yttrium oxide (Nd:Y₂O₃) amorphous precursor compaction and sintering is being reported for the first time. Precursor of 2 at.% Nd³⁺ doped Y₂O₃ was synthesized by gelation of sol of yttrium and neodymium nitrates with l-alanine at 80 °C for 16 h followed by gel combustion in microwave. A part of microwave precursor was heat treated at 700 °C for 5 h to give the partially crystalline Nd:Y₂O₃ amorphous precursor. Thermogravimetric analysis (TGA) of partially crystalline amorphous precursor of Nd:Y₂O₃ gave 8.5% total weight loss indicating removal of maximum organics. X-Ray diffraction (XRD) showed broad peaks indicating incomplete crystallization of cubic Nd:Y₂O₃. Morphology was found to be close to spherical with particles in size range 17–19 nm by TEM. Another part of microwave precursor on calcination at 1000 °C for 3 h led to formation of fully crystalline Nd:Y₂O₃ with particles in size range of 35–85 nm. Both partially crystalline amorphous precursor and fully crystalline Nd:Y₂O₃ were compacted at 400 MPa by cold isostatic press and sintered at 1750 °C for 10 h under vacuum (10^?5 mbar). The partially crystalline Nd:Y₂O₃ amorphous precursor densified to 99% with 65% transmission at 2500 nm (0.5 mm thickness) compared to 96% densification with 34% transmission for fully crystalline Nd:Y₂O₃ without any sintering aids. Retention of cubic phase purity of Y₂O₃ was observed in both the ceramic pellets post sintering by XRD. Good grain fusion with grain growth to ≤2 μm was observed by scanning electron microscope (SEM) for partially crystalline Nd:Y₂O₃ amorphous precursor. Thus partially crystalline Nd:Y₂O₃ amorphous precursor nanopowders, with homogeneous close to spherical fine particles and high reactivity due to ionic mobility of amorphous phase, led to better densification.     

Flash sintering of a three‐phase alumina,spinel, and yttria‐stabilized zirconia composite

Three‐phase ceramic composites constituted from equal volume fractions of α‐Al₂O₃, MgAl₂O₄ spinel, and cubic 8 mol% Y₂O₃‐stabilized ZrO₂ (8YSZ) were flash‐sintered under the influence of DC electric fields. The temperature for the onset of rapid densification (flash sintering) was measured using a constant heating rate at fields of 50‐500 V/cm. The experiments were carried out by heating the furnace at a constant rate. Flash sintering occurred at a furnace temperature of 1350°C at a field of 100 V/cm, which dropped to 1150°C at a field of 500 V/cm. The sintered densities ranged from 90% to 96%. Higher electric fields inhibited grain growth due to the lowering of the flash temperature and an accelerated sintering rate. During flash sintering, alumina reacted with the spinel phase to form a high‐alumina spinel solid solution, identified by electron dispersive spectroscopy and from a decrease in the spinel lattice parameter as measured by X‐ray diffraction. It is proposed that the solid solution reaction was promoted by a combination of electrical field and Joule heating.     

The effect of Zn addition on the structure and transport properties of BaCe0.9−xZrxY0.1O3−δ

BaCe_0.9−xZr_xY_0.1O_3−δ (0.1 ≤ x ≤ 0.9) are ceramic proton conductors widely investigated for different electrochemical devices, such as Solid Oxide Fuel Cell (SOFC) electrolytes, however, their applications are limited by the high sintering temperatures necessary to achieve densification. Polycrystalline powders of BaCe_0.9−xZr_xY_0.1O_3−δ (BCZ) have been prepared by freeze-drying precursor method at 1000 °C. These powders were mixed with a zinc nitrate solution to decrease the sintering temperature to 1200–1300 °C. The addition of Zn has several effects on the structure and microstructure of BCZ: the densification and grain growth are enhanced at lower temperature and a reduction of the crystallographic symmetry is observed for samples with low Zr-content (x ≤ 0.3). Furthermore, the bulk and specific grain boundary conductivities are only slightly affected by the addition of Zn.     

Flash sintering of Al2O3–ZrO2 ceramics under alternating current electric field

In this study, the influence of alternating current (AC) electric field on flash sintering and microstructural evolution of alumina–zirconia (Al₂O₃–ZrO₂) composite was systematically investigated at furnace temperature of 800 °C. Compared with direct current (DC) electric field, AC electric field not only promoted densification and grain growth of Al₂O₃–ZrO₂ composite, but also improved the uniformity of microstructure of ceramics. Grain size of AC flash-sintered samples was found to be inversely related to electric field, and positive correlation was observed with current density limit. Dense Al₂O₃–ZrO₂ composite ceramic was fabricated via AC flash sintering under 60 mA mm^?2 at low furnace temperature within 120 s, and as-sintered samples exhibited relatively good mechanical properties. The mechanism involving synergistic effect of Joule heating and defects generation under the influence of electric field was proposed to explain rapid densification during AC flash sintering. These results indicate the feasibility of preparation of dense composite ceramic with homogeneous microstructure via AC flash sintering.     

Phase-transformation and grain-growth kinetics in yttria-stabilized tetragonal zirconia polycrystal doped with a small amount of alumina

Microstructure development during sintering in 3 mol% Y₂O₃-stabilized tetragonal zirconia polycrystal doped with a small amount of Al₂O₃ was investigated in the isothermal sintering conditions of 1300–1500 °C. At the low sintering temperature at 1300 °C, although the density was relatively high, the grain-growth rate was much slow. In the specimen sintered at 1300 °C for 50 h, Y³⁺ and Al³⁺ ions segregated along grain boundaries within the widths of about 10 and 6 nm, respectively. In grain interiors, the cubic-phase regions were formed by not only a grain-boundary segregation-induced phase-transformation mechanism but also by spinodal decomposition. The grain-growth behavior was kinetically analyzed using the grain-size data in 1300–1500 °C, which indicated that the grain-growth rate was enhanced by Al₂O₃-doping. These phase-transformation and grain-growth behaviors are reasonably explained by the diffusion-enhanced effect of Al₂O₃-doping.