New Fully‐Differential CMOS Second‐Generation Current Conveyer

This paper presents a new CMOS fully‐differential second‐generation current conveyor (FDCCII). The proposed FDCCII is based on a fully‐differential difference transconductor as an input stage and two class AB output stages. Besides the proposed FDCCII circuit operating at a supply voltage of ± 1.5 V, it has a total standby current of 380 µA. The applications of the FDCCII to realize a variable gain amplifier, fully‐differential integrator, and fully‐differential second‐order bandpass filter are given. The proposed FDCII and its applications are simulated using CMOS 0.35 µm technology.     

Low‐Voltage CMOS Current Feedback Operational Amplifier and Its Application

A novel low‐voltage CMOS current feedback operational amplifier (CFOA) is presented. This realization nearly allows rail‐to‐rail input/output operations. Also, it provides high driving current capabilities. The CFOA operates at supply voltages of ±0.75 V with a total standby current of 304 µA. The circuit exhibits a bandwidth better than 120 MHz and a current drive capability of ±1 mA. An application of the CFOA to realize a new all‐pass filter is given. PSpice simulation results using 0.25 µm CMOS technology parameters for the proposed CFOA and its application are given.     

DVCC-based very low-offset current-mode instrumentation amplifier

This paper presents an alternative implementation of a chopper-modulated current-mode instrumentation amplifier. The structure provides very low-offset voltage at the output due to chopper modulation and residual offset removal path. The residual offset removal path is based on low-pass filtering using grounded capacitances which provides compact design structure compared to various chopper-modulated instrumentation amplifier designs. Rail-to-rail input common-mode range is possible due to transmission gate-based input chopper switching scheme. The design is made using a 0.35-µm CMOS process with ±1.65 V supply voltage. The area of the amplifier is 234µm × 344 µm, including all the filtering elements. The proposed circuit with residual offset removal path provides less than 1 µV input referred offset voltage. The advantage of the proposed instrumentation amplifier is its large bandwidth, simple design scheme and compact area compared to chopper-modulated voltage mode amplifiers.     

High‐Gain Double‐Bulk Mixer in 65 nm CMOS with 830 pW Power Consumption

A low‐power down‐sampling mixer in a low‐power digital 65 nm CMOS technology is presented. The mixer consumes only 830 µW at 1.2 V supply voltage by combining an NMOS and a PMOS mixer with cascade transistors at the output. The measured gain is (19 °1 dB) at frequencies between 100 MHz and 3 GHz. An IIP3 of ?5.9 dBm is achieved.     

A low-voltage low-power instrumentation amplifier based on supply current sensing technique

In this paper a new low-voltage low-power instrumentation amplifier (IA) is presented. The proposed IA is based on supply current sensing technique where Op-Amps in traditional IA based on this technique are replaced with voltage buffers (VBs). This modification results in a very simplified circuit, robust performance against mismatches and high frequency performance. To reduce the required supply voltage, a low-voltage resistor-based current mirror is used to transfer the input current to the load. The input and output signals are of voltage kind and the proposed IA shows ideal infinite input impedance and a very low output one. PSPICE simulation results, using 0.18 μm TSMC CMOS technology and supply voltage of ±0.9 V, show a 71 dB CMRR and a 85 MHz constant −3 dB bandwidth for differential-mode gain (ranging from 0 dB to 18 dB). The output impedance of the proposed circuit is 1.7 Ω and its power consumption is 770 µW. The method introduced in this paper can also be applied to traditional circuits based on Op-Amp supply current sensing technique.     

A New Automatic Compensation Network for System‐on‐Chip Transceivers

This paper proposes a new automatic compensation network (ACN) for a system‐on‐chip (SoC) transceiver. We built a 5 GHz low noise amplifier (LNA) with an on‐chip ACN using 0.18 µm SiGe technology. This network is extremely useful for today's radio frequency (RF) integrated circuit devices in a complete RF transceiver environment. The network comprises an RF design‐for‐testability (DFT) circuit, capacitor mirror banks, and a digital signal processor. The RF DFT circuit consists of a test amplifier and RF peak detectors. The RF DFT circuit helps the network to provide DC output voltages, which makes the compensation network automatic. The proposed technique utilizes output DC voltage measurements and these measured values are translated into the LNA specifications such as input impedance, gain, and noise figure using the developed mathematical equations. The ACN automatically adjusts the performance of the 5 GHz LNA with the processor in the SoC transceiver when the LNA goes out of the normal range of operation. The ACN compensates abnormal operation due to unusual thermal variation or unusual process variation. The ACN is simple, inexpensive and suitable for a complete RF transceiver environment.     

Low-voltage,wide-range,current-controlled DC current generator

Operating from a 1?V rail supply, a proposed CMOS current-controlled DC current generator can function as a repeater, attenuator or amplifier over the input current range, 1?µA to 1?mA, with a current-transfer ratio accuracy better than 1% using IBM technology, characterised by a process with a 0.13?µm minimum feature size. In repeater mode, the incremental output resistance exceeds 30?MΩ for an output current of 500?µA at an output voltage of 0.20?V, and exceeds 1?MΩ for an output current of 1?mA at an output voltage of 0.22?V. For zero input current, the circuit dissipation is 117?µW.     

250 mV Supply Voltage Digital Low‐Dropout Regulator Using Fast Current Tracking Scheme

This paper proposes a 250 mV supply voltage digital low‐dropout (LDO) regulator. The proposed LDO regulator reduces the supply voltage to 250 mV by implementing with all digital circuits in a 0.11 μm CMOS process. The fast current tracking scheme achieves the fast settling time of the output voltage by eliminating the ringing problem. The over‐voltage and under‐voltage detection circuits decrease the overshoot and undershoot voltages by changing the switch array current rapidly. The switch bias circuit reduces the size of the current switch array to 1/3, which applies a forward body bias voltage at low supply voltage. The fabricated LDO regulator worked at 0.25 V to 1.2 V supply voltage. It achieved 250 mV supply voltage and 220 mV output voltage with 99.5% current efficiency and 8 mV ripple voltage at 20 μA to 200 μA load current.     

Low‐Power,All Digital Phase‐Locked Loop with a Wide‐Range,High Resolution TDC

In this paper, we propose a low‐power all‐digital phase‐ locked loop (ADPLL) with a wide input range and a high resolution time‐to‐digital converter (TDC). The resolution of the proposed TDC is improved by using a phase‐interpolator and the time amplifier. The phase noise of the proposed ADPLL is improved by using a fine resolution digitally controlled oscillator (DCO) with an active inductor. In order to control the frequency of the DCO, the transconductance of the active inductor is tuned digitally. The die area of the ADPLL is 0.8 mm² using 0.13 µm CMOS technology. The frequency resolution of the TDC is 1 ps. The DCO tuning range is 58% at 2.4 GHz and the effective DCO frequency resolution is 0.14 kHz. The phase noise of the ADPLL output at 2.4 GHz is ‐120.5 dBc/Hz with a 1 MHz offset. The total power consumption of the ADPLL is 12 mW from a 1.2 V supply voltage.     

Rail-supply insensitive CMOS current generator

The theoretical background and a selection of simulated results are presented for a 10?µA PTAT current generator that is a modified CMOS version of an existing bipolar configuration. Using standard 0.35?µm CMOS technology, the circuit exhibits a current variation of less than 0.01% when the supply rail voltage is changed from 0.5 to 10?V.     

电流激励神经信号再生电路

介绍了一种电流激励神经信号再生电路,该电路由探测电路和激励电路组成。探测电路由全差分运算放大器和仪表放大器组成。全差分运算放大器从神经元上端探测并放大神经信号,仪表放大器对信号进一步放大。最后激励级的跨导放大器将电压线性的转化为电流。电路采用CSMC0.5μmCMOS工艺设计,芯片版图尺寸为0.93mm×0.60mm。芯片的仿真结果为：在±2.5V供电电压下,功耗为8.1mW,输出电流最高可达0.357mA,输出电阻为152kΩ,总谐波失真小于1.9%。     

Smart sensor interfacing circuit using square-rooting current-to-frequency conversion

A universal sensor interfacing circuit is presented in this paper. It is capable of giving a digital output directly proportional to various types of measured quantities, where those measured quantities are proportional to the square root of some other type of quantity. This sensor interfacing circuit is a square-rooting current-to-frequency converter. The design is based on two current-controlled resistors in CMOS technology with bisection of the input voltage used in place of the ordinary resistors within the relaxation oscillator. There is no need for highly stable voltage or current references in the proposed design. The temperature stability of the design is achieved without the need for any specific setting of the process parameters. Experimental results, obtained on a circuit implemented by discrete components, confirm the predictions of the analysis performed. The relative errors are less than 1% for the input current range from 12 µA to 650 µA, and for the output frequency range from 231 Hz to 2.625 kHz. A solution for extending the input current dynamic range is also given in the paper.     

1.5 V Sub‐mW CMOS Interface Circuit for Capacitive Sensor Applications in Ubiquitous Sensor Networks

In this paper, a low‐power CMOS interface circuit is designed and demonstrated for capacitive sensor applications, which is implemented using a standard 0.35‐μm CMOS logic technology. To achieve low‐power performance, the low‐voltage capacitance‐to‐pulse‐width converter based on a self‐reset operation at a supply voltage of 1.5 V is designed and incorporated into a new interface circuit. Moreover, the external pulse signal for the reset operation is made unnecessary by the employment of the self‐reset operation. At a low supply voltage of 1.5 V, the new circuit requires a total power consumption of 0.47 mW with ultra‐low power dissipation of 157 μW of the interface‐circuit core. These results demonstrate that the new interface circuit with self‐reset operation successfully reduces power consumption. In addition, a prototype wireless sensor‐module with the proposed circuit is successfully implemented for practical applications. Consequently, the new CMOS interface circuit can be used for the sensor applications in ubiquitous sensor networks, where low‐power performance is essential.     

An improved current mode logic latch for high‐speed applications

In this paper, an improved current mode logic (CML) latch design is proposed for high‐speed on‐chip applications. Transceivers use various methods in fast data transmission in wireless/wire‐line application. For an asynchronous transceiver, the improved CML latch is designed using additional NMOS transistors in conventional CML latch which helps to boost the output voltage swing. The proposed low‐power CML latch‐based frequency divider is compatible for higher operating frequency (16 GHz). Next, the delay model is also developed based on small signal equivalent circuit for the analysis of the proposed latch. The output voltage behavior of the proposed latch is analyzed using 180‐nm standard CMOS technology.     

一种新型的宽线性范围差分电压输入电流传输器及其应用

设计了一种带有共模检测电路的宽线性范围差分电压输入电流传输器(DVCCⅡ).所提出的电路具有动态的长尾电流的差分对,可获得较大的动态线性输入范围.所提出的电路可以得到精确跟随特性和宽线性输入范围,且比较已有电路具有低电压低功耗等特点.采用SMIC 0.18μm工艺,用Spectre对电路进行仿真,电源电压是1.8 V,...     

A resistorless CMOS bandgap reference with low temperature coefficient and high PSRR

A novel bandgap reference (BGR) with low temperature and supply voltage sensitivity without any resistor, which is compatible with standard CMOS process, is presented in this article. The proposed BGR utilises a differential amplifier with an offset voltage proportional to absolute temperature to compensate the temperature drift of emitter–base voltage. Besides, a self-biased current source with feedback is used to provide the bias current of the BGR core for reducing current mirror errors dependent on supply voltage and temperature further. Verification results of the proposed BGR implemented with 0.35?µm CMOS process demonstrate that a temperature coefficient of 10.2?ppm/°C is realised with temperature ranging from ?40°C to 140°C, and a power supply rejection ratio of 58?dB is achieved with a maximum supply current of 27?µA. The active area of the presented BGR is 160?×?140?µm².     

An Experimental 0.8 V 256‐kbit SRAM Macro with Boosted Cell Array Scheme

This work presents a low‐voltage static random access memory (SRAM) technique based on a dual‐boosted cell array. For each read/write cycle, the wordline and cell power node of selected SRAM cells are boosted into two different voltage levels. This technique enhances the read static noise margin to a sufficient level without an increase in cell size. It also improves the SRAM circuit speed due to an increase in the cell read‐out current. A 0.18 µm CMOS 256‐kbit SRAM macro is fabricated with the proposed technique, which demonstrates 0.8 V operation with 50 MHz while consuming 65 µW/MHz. It also demonstrates an 87% bit error rate reduction while operating with a 43% higher clock frequency compared with that of conventional SRAM.     

A Power‐Efficient CMOS Adaptive Biasing Operational Transconductance Amplifier

This paper presents a two‐stage power‐efficient class‐AB operational transconductance amplifier (OTA) based on an adaptive biasing circuit suited to low‐power dissipation and low‐voltage operation. The OTA shows significant improvements in driving capability and power dissipation owing to the novel adaptive biasing circuit. The OTA dissipates only 0.4 μW from a supply voltage of ±0.6 V and exhibits excellent high driving, which results in a slew rate improvement of more than 250 times that of the conventional class‐AB amplifier. The design is fabricated using 0.18‐μm CMOS technology.     

锁相环频率合成器中的电荷泵设计

用TSMC 0.18μm CMOS工艺设计了一种电荷泵电路。传统的电荷泵电路中充放电电流有较大的电流失配,文章采用与电源无关的基准电流源电路,运用运算放大器和自偏置高摆幅共源共栅电流镜电路实现了充放电电流的高度匹配。仿真结果表明:电源电压1.8V时,电荷泵电流为0.5mA;在0.3V～1.6V输出电压范围内电流失配小于1μA,功耗为6.8mW。     

Voltage‐Mode 1.5 Gbps Interface Circuits for Chip‐to‐Chip Communication

In this paper, interface circuits that are suitable for point‐to‐point interconnection with an over 1 Gbps data rate per pin are proposed. To achieve a successful data transfer rate of multi‐gigabits per‐second between two chips with a point‐to‐point interconnection, the input receiver uses an on‐chip parallel terminator of the pass gate style, while the output driver uses the pullup and pulldown transistors of the diode‐connected style. In addition, the novel dynamic voltage level converter (DVLC) has solved such problems as the access time increase and valid data window reduction. These schemes were adopted on a 64 Mb DDR SRAM with a 1.5 Gbps data rate per pin and fabricated using a 0.10 µm dual gate oxide CMOS technology.