BaFe12O19/SiO2微晶玻璃陶瓷的柠檬酸盐Sol-Gel合成及其微波性能的研究

采用柠檬酸sol-gel工艺合成了BaFe12O19/SiO2微晶玻璃陶瓷,并对其介电常数及其磁导率在100MHz-6GHz下的变化规律进行了研究。结果表明,BaFe12O19/SiO2微晶玻璃陶瓷的合成与体系中Fe/Ba,烧结温度密切相关;其介电常数、磁导率基本都随测试频率的增加而下降,介电损耗值最大达到0．40,磁损耗值较小。     

BaFe12O19／Al2O3—SiO2—K2O微晶玻璃陶瓷的柠檬酸Sol—Gel合成及其微波性能的研究

采用柠檬酸sol-gel工艺合成了BaFe12O19/Al2O3-SiO2-K2O微晶玻璃陶瓷，并对其介电常数及其磁导率在1MHz～6GHz下的变化规律进行了研究。结果表明，BaFe12O19/Al2O3-SiO2-K2O微晶玻璃陶瓷的合成与体系中Fe/Ba、烧结温度密切相关；其介电常数、磁导率基本都随测试频率的增加而下降；介电损耗值最大可达到0.30，磁损耗值较小。     

BaFe_(12)O_(19)/SiO_2微晶玻璃陶瓷的柠檬酸盐Sol-Gel合成及其微波性能的研究

采用柠檬酸 Ｓoｌ－ｇｅｌ工艺合成了 ＢａＦｅ12Ｏ１９／ＳｉＯ２微晶玻璃陶瓷,并对其介电常数及其磁导率在１００ＭＨｚ～６ＧＨｚ下的变化规律进行了研究.结果表明,ＢａＦｅ１２Ｏ１９／ＳｉＯ２微晶玻璃陶瓷的合成与体系中 Ｆｅ／Ｂａ、烧结温度密切相关;其介电常数、磁导率基本都随测试频率的增加而下降;介电损耗值最大达到０．４０,磁损耗值较小．     

The preparation and microwave properties of Ba3ZnZCo2-ZFe24O41/SiO2 microcrystalline glass ceramics by citrate sol-gel process

A series of Ba₃Zn_ZCo_2-ZFe₂₄O₄₁/SiO₂ microcrystalline glass ceramics with Z=0.0,0.4,0.8 and 1.2 were prepared by citrate sol-gel process. The result showed that Ba₃Zn_ZCo_2-ZFe₂₄O₄₁ hexferrite crystallites could be obtained by this process at 1200 °C in the system of BaO-Fe₂O₃-CoO-ZnO-SiO₂. The complex dielectric constant and complex permeability of Ba₃Zn_ZCo_2-ZFe₂₄O₄₁/SiO₂ microcrystalline glass ceramics calcined at different temperature were measured in the range of 200MHz-6 GHz by transmission/reflection coaxial line method. The complex dielectric constant and dielectric loss exhibited insignificant variety in the whole range of measuring frequencies for all samples. The real part of the permeability decreased as the measuring frequency increasing, and calcining temperature had a clear influence on the value of μ′ for Ba₃Zn_ZCo_2-ZFe₂₄O₄₁/SiO₂ microcrystalline glass ceramics, and so did the content of Zn²⁺ and Co²⁺. The natural resonance phenomenon was observed in μ′′ spectra for all the Ba₃Zn_ZCo_2-ZFe₂₄O₄₁/SiO₂ microcrystalline glass ceramics. The substitution of Zn²⁺ ion and annealing temperature closely affect the resonance frequency, the more the Zn²⁺ ion, the higher the annealing temperature and the lower the resonance frequency. Received: 23 July 2001 / Accepted: 24 July 2001     

Preparation and microwave properties of Y-type magnetoplumbite microcrystalline glass ceramic with the composition 0.5(Ba2ZnZCo2-ZFe12O22)·0.5SiO2

The citrate sol-gel synthesis technique was used to prepared Ba₂Zn_ZCo_2-ZFe₁₂O₂₂/SiO₂ microcrystalline glass ceramic with Z=2.0, 1.6, 1.2, and 0.8. Several methods such as X-ray diffractometry, scanning electron microscopy and HP vector network analyzer were used to obtain detailed information on the crystallography and magnetic properties of Ba₂Zn_ZCo_2-ZFe₁₂O₂₂/SiO₂ microcrystalline glass ceramic. The correlation of the formation of Ba₂Zn_ZCo_2-ZFe₁₂O₂₂/SiO₂ microcrystalline glass ceramic with thermal treatment was studied. The complex dielectric constant and complex permeability of microcrystalline glass ceramic-paraffin wax composites were measured by the transmission/reflection coaxial line method in the range from 100MHz to 6 GHz. The effects of composition, annealing temperature and measuring frequency on complex permittivity and permeability of Ba₂Zn_ZCo_2-ZFe₁₂O₂₂/SiO₂ microcrystalline glass ceramic were also investigated. Received 23 July 2001 / Accepted: 24 July 2001     

Low temperature sintering and microwave dielectric properties of zinc silicate ceramics

Effects of ZnO–B₂O₃–SiO₂ glass on the sintering behavior, the microstructure, and the microwave dielectric properties of Zn₂SiO₄ ceramics have been investigated. The ZnO–B₂O₃–SiO₂ glass lowered the sintering temperature of Zn₂SiO₄ ceramics effectively from 1300 to 900 °C. The X-ray diffraction results showed that the secondary phase of SiO₂ in the Zn₂SiO₄ ceramics could be dissolved in the glass. The dielectric constant decreased slightly, and the quality factor decreased with increasing glass content. Especially, when the glass content was chosen as 20 wt%, the ceramics sintered at 900 °C for 2 h exhibited a low dielectric constant of 6.85, a high quality factor of 31,690 and the temperature coefficient of the resonant frequency of −28 ppm/°C, which demonstrated a good potential for use in low temperature co-fired ceramics field.     

Effects of SrO–B2O3–SiO2 glass additive on the microstructure and dielectric properties of CaCu3Ti4O12

The effect of SrO–B₂O₃–SiO₂ glass additive (SBS) on the microstructure and dielectric properties of CaCu₃Ti₄O₁₂ (CCTO) ceramics was investigated. This SBS–added CCTO ceramics were prepared by the solid state reaction. The undesirable impurity phases Ca₃SiO₅ started appearing in the XRD patterns, suggesting a possible chemical reaction between CaTiO₃ and SiO₂ (the devitrification production of SBS glass). The SBS glass additive promoted the grain growth and densification of CCTO ceramics. Cole–Cole plots of conductance suggested that the resistivity grain boundary decreased with increasing amount of SBS glass (when x = 0–2 wt%), then increased (when x = 2–3 wt%). The addition of SBS glass was desirable to increase the dielectric constants (up to 10⁴) and lowered the dielectric losses of CCTO over the frequency range of 450–40 kHz at the relatively lower sintering temperature for relatively shorter sintering time (1,050 °C, 12 h).     

Electrical properties of R<Subscript>2</Subscript>O–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> glass–ceramics for anodic bonding

Temperature and frequency dependence on electrical properties (dielectric constant, dielectric loss and conductivity) of Li₂O–Na₂O–K₂O–Al₂O₃–SiO₂(R₂O–Al₂O₃–SiO₂) system glass–ceramics used as anodic bonding materials were discussed. The results showed that the main crystal phase of glass–ceramics was lithium metasilicate (Li₂SiO₃). Compared with the parent glass, both the dielectric constant and dielectric loss of glass–ceramics decreased, the dielectric constant and dielectric loss increased gradually with the increasing of the test temperature from room temperature to 400 °C, Testing frequency (30–300 MHz) had very little influence on the dielectric properties of samples. The electrical conductivity of glass–ceramics showed a trend of first decrease and then increase with the increasing of temperature. The glass–ceramics which has a lower dielectric constant, dielectric loss and better stability under high frequency was obtained after an appropriate heat treatment; it could be used as anodic bonding materials under very high frequency.     

BaFe12O19/SiO2-B2O3-K2O 微晶玻璃陶瓷的低温合成及其微波性能

采用柠檬酸sol-gel工艺合成了BaFe₁₂O₁₉/SiO₂-B₂O₃-K₂O微晶玻璃陶瓷, 并对其介电常数及其磁导率在100MHz～ 6 GHz 下的变化规律进行了研究。结果表明: BaFe₁₂O₁₉/SiO₂-B₂O₃-K₂O微晶玻璃陶瓷可以在850℃/5 h的条件下烧结而成, 其合成过程与体系中的Ba/Fe 密切相关; 其介电常数基本不随测试频率的变化而变化; 其磁导率实部随测试频率的增加而下降。      

Direct-current field dependence of dielectric properties in B2O3-SiO2 glass doped Ba0.6Sr0.4TiO3 ceramics

The Ba_0.6Sr_0.4TiO₃ ceramics doped B₂O₃-SiO₂ glass prepared by a sol-gel process and the effect of glass content on the DC field dependence of dielectric characteristics in Ba_0.6Sr_0.4TiO₃ ceramics were studied. The samples were observed and analysed by SEM and X-ray diffraction. The dielectric constant of a BST sample with 1 mol% B₂O₃-SiO₂ sintered at 1250°C was as good as that of undoped BST sintered at 1340°C. The dielectric constant samples decreases as the applied DC field increases. The influence of the DC field on the loss factor is much less than that on the dielectric constant. With increasing of the applied voltage, the T _c was increased and the peaks were surpressed and broadened. With increasing of glass content, the peaks were also surpressed and broadened. The maximum dielectric constant and the percentage change of dielectric constant under a DC field increase.     

Magnetic and dielectric properties of the M-type barium strontium hexaferrite (Ba x Sr1−x Fe12O19) in the RF and microwave (MW) frequency range

This paper presents results for the dielectric permittivity (ε′), dielectric loss (tg δ _E) dielectric permeability (μ′) and magnetic loss (tg δ _M) in the radio-frequency and microwave frequency range of Ba _x Sr_1−x Fe₁₂O₁₉ hexaferrite (0 ≤ x ≤ 1). The samples were prepared by a new route of the ceramic method. The magnetic permeability (μ′) and magnetic loss (tg δ _M) measurements in the range 100 MHz to 1.5 GHz, reveals that 1.32 ≤ μ′ ≤ 1.68 for the permeability of BFO100 (BaFe₁₂O₁₉) and 1.16 < μ′ ≤ 1.88 for SFO100 (SrFe₁₂O₁₉) in the range of studied frequencies. The BFO100 sample presented lower loss (tg δ _M = 4.10⁻³ at 1.5 GHz). The permittivity of BFO100 and SFO100 in 1.5 GHz are, respectively 8.18 and 8.19, and in the 1 MHz are, respectively 52.04 and 19.09. The samples presented coercive field in the range of 3–5 kOe and remanence magnetization in the range of 33–36 emu/g. The subjects of paper were study the dielectric and magnetic properties of the barium and strontium hexaferrite, in view of applications as a material for permanent magnets, high density magnetic recording and microwave devices.     

Characterization and analysis of CaO–SiO<Subscript>2</Subscript>–B<Subscript>2</Subscript>O<Subscript>3</Subscript> ternary system ceramics

The dielectric, thermal and mechanical properties of CaO–SiO₂–B₂O₃ ternary system ceramics by solid-phase method have been carried out and quantitive analysis been examined by X-ray diffraction (XRD) patterns. The results showed that the major crystalline phase of CaO–SiO₂–B₂O₃ ternary system ceramics was wollastonite (about 90 wt%) which existed at the temperature ranging from 950 to 1,100 °C. It is also observed that wollastonite could be transformed to pseudowollastonite at 1,200 °C. In addition, with increase in calcination temperature, the amount of wollastonite increases. When the sintering temperature is at 1,100 °C, the amount of wollastonite has a maximum value of 92.7 wt%. Accordingly, CaO–SiO₂–B₂O₃ ternary system ceramics achieved excellent properties at 1,100 °C, such as dielectric constant of 8.38, dielectric loss of 1.51 × 10⁻³ at 1 MHz, linear thermal-expansion coefficient (300 K) of 6.68 × 10⁻⁶/K, bending strength of 121.75 Mpa. Analysis of the mechanical and dielectric properties showed that the measured bending strength, dielectric constant and loss of CaO–SiO₂–B₂O₃ ternary system ceramics can be substantially modified and improved by controlling the sintering temperature, in particular due to the amount of wollastonite crystalline phase and size of grains.     

Microwave absorption properties of substituted BaFe<Subscript>12</Subscript>O<Subscript>19</Subscript>/TiO<Subscript>2</Subscript> nanocomposite multilayer film

The nanocomposite multilayer film (NCMF) of substituted BaFe₁₂O₁₉ and TiO₂ was prepared using sol-gel method. BaFe_10.5Al_1.5O₁₉, BaFe_10.1Al_1.9O₁₉ and BaFe_11.4Cr_0.6O₁₉ with different absorption frequencies were selected to fabricate the multilayer film with TiO₂. The morphology, crystalline structure and microwave absorption property of the NCMF were investigated with an atomic force microscopy, X-ray diffraction and vector network analyses. The results show that the NCMF is uniform without microcracks and it is an ideal microwave attenuation material with a broad frequency range. Its maximum loss efficiency is about −40 dB. The frequency range with the loss above −10 dB is more than 7 GHz. The multilayer film assembles the achievements of each layer film. Moreover, the compounding of ferrites with TiO₂ is helpful to absorb more microwave energy. TiO₂ particles block the growth of ferrite grains and make most of their size within nanometers. TiO₂ also improves the dielectric loss efficiency of the NCMF.     

Low-temperature sintering of (Zn0.8 Mg0.2)2SiO4-TiO2 ceramics

Effect of Li₂O-B₂O₃-SiO₂ (LBS) glass on the sintering behavior and the microwave dielectric properties of (Zn_0.8 Mg_0.2)₂SiO₄-TiO₂ (ZMST) ceramics were investigated. The Li₂O-B₂O₃-SiO₂ glass lowered the sintering temperature of ZMST ceramics effectively from 1250 to 870 °C. The unknown second phase, which was formed in the ZMST ceramics increased with the addition of LBS glass. With increasing the LBS glass content, the bulk density, dielectric constant (ε_r) and the maximum Q × f value decreased, and the temperature coefficient of resonant frequency (τ_f) shifted to a negative value. (Zn_0.8 Mg_0.2)₂SiO₄-TiO₂ ceramics with 3 wt.% Li₂O-B₂O₃-SiO₂ glass sintered at 870 °C for 2 h shows excellent dielectric properties: ε_r = 8.48, Q × f = 11500 GHz, and τ_f = 0 ppm/°C.     

Infrared and microwave absorbing properties of BaTiO3/polyaniline and BaFe12O19/polyaniline composites

BaTiO₃/polyaniline and BaFe₁₂O₁₉/polyaniline composites were synthesized by in situ polymerization and introduced into epoxy resin and polyethylene to be microwave and infrared absorber. The spectroscopic characterizations of the formation processes of BaTiO₃/polyaniline and BaFe₁₂O₁₉/polyaniline composites were examined using Fourier transform infrared, ultraviolet–visible spectrophotometer, X-ray diffraction, scanning electron microscopy, transmission electron microscopy and electron spin resonance. Microwave absorbing properties were investigated by measuring reflection loss in the 2–18 and 18–40 GHz microwave frequency range using the free space method. The thermal extinction measurements in the 3–5 and 8–12 μm were done to evaluate the shielding affectivity of infrared. The results showed that the BaTiO₃/polyaniline and BaFe₁₂O₁₉/polyaniline composites have good compatible dielectric and magnetic properties and hence the microwave absorbency show broad frequencies absorbing properties. Moreover, the infrared thermal image testing that the detecting ability of infrared thermal imaging was decreased when the BaFe₁₂O₁₉ and BaTiO₃ was coating with polyaniline.     

Dielectric constant, magnetic permeability and microwave absorption studies of hot-pressed Ba-CoTi hexaferrite composites in X-band

The microwave absorption, complex permittivity and complex permeability studies of hot-pressed hexaferrite composites prepared with Ba(CoTi)_xFe_12-2xO₁₉ (x = 0.0, 0.2, 0.4, 0.8, and 1.0) were made in the frequency range from 8.0 to 12.4 GHz. The hexaferrite composites with x > 0.0 exhibit significant dispersion in the complex permittivity (ε_r′-jε_r″). However the dispersion in complex permeability (μ_r′-jμ_r″) is not significant and is attributed to the shielding effect of polymer matrix over the ferrite crystallites. The reflection loss has been studied as function of frequency, composition and thickness of absorber. A comparison of reflection loss of hot-pressed ferrite composites with that of normal sintered ferrite composites was made and analyzed. A minimum reflection loss of—24.0 dB is obtained at 9.9 GHz for 2.8 mm thick sample of BaCo_0.4Ti_0.4Fe_11.2O₁₉ hot-pressed hexaferrite composite.     

Definitive experimental evidence for <Emphasis Type="Italic">Microwave Effects</Emphasis>: radically new effects of separated E and H fields,such as decrystallization of oxides in seconds

Inspite of overwhelming evidence showing that a variety of solid state reactions were radically different when performed in a multimode microwave chamber compared to conventional heating some still question whether there is direct link to the radiation field. The present study has been conducted, for the first time ever, in a single mode TE₁₀₃ cavity at 2.45 GHz. A large variety of materials have been reacted as ≈1 cm φ, 2 mm thick samples within the same cavity, at the positions of the E field and H field maxima. Enormous differences are shown to occur for certain families of common ceramic phases depending only on which of the E or H fields were used. The most extraordinary effects and sharpest differences (noted to date) between reactions at the E and H nodes have been found in ferroic oxides. Phases such as Fe₃O₄ or binary compounds such as BaFe₁₂O₁₉ are rendered non-crystalline to XRD in a few seconds in the H field, although they show no bulk evidence for melting. The microstructures are unique, showing smooth glass-like regions with regular waves parallel to each other. In the E field node the identical pellet components react completely and form large euhedral crystals of a single phase. The phenomenon of de-crystallization or formation of nano-glasses was confirmed for all the 3d ferrite phases. The magnetic properties of these decrystallized ferro-magnetic phases also show remarkable changes from the original very hard, transforming to very soft, magnets. Electronic Publication     

Sintering and crystallization of cordierite glass ceramics for high frequency multilayer chip inductors

Cordierite-based ceramics were developed by sintering a glass selected from MgO-Al₂O₃-SiO₂ system with an aim to use the material as high frequency chip inductors. A small amount of B₂O₃ and P₂O₅ were added to optimize the preparation conditions. The glass powder and sintered bodies were characterized by different analytical techniques such as TG-DTA analysis, X-ray diffraction, transmission and scanning electron microscopy. Pellets uniaxially pressed from the glass power could be sintered well at 950 °C having a density of above 99% theoretically, dielectric constant of 5.5, dielectric loss of 0.001 and thermal expansion coefficient of 26.7×10⁻⁷ °C⁻¹ (20-400 °C). Crystalline phases in this sintered sample are predominantly α-cordierite (hexagonal high cordierite) and trace amount of μ-cordierite. SEM depicted a uniformly dense microstructure with crystals of granular habit in the sintered sample.     

Characterization of borophosphosilicate glass soot fabricated by flame hydrolysis deposition for silica-on-silicon device applications

The use of flame hydrolysis deposition (FHD) to fabricate porous silica glass soot in the B₂O₃-P₂O₅-SiO₂ glass system (BPSG) is described for silica-on-silicon device applications. The deposition conditions with a Si substrate temperature (200 °C) and a flame temperature (1300–1500 °C) are appropriate to synthesize the SiO₂ and P₂O₅-SiO₂ non-crystalline glass soot. However, further investigations for the B₂O₃-P₂O₅-SiO₂ glass soot are needed to obtain complete amorphous phases. The densification process of porous silica glass soot in the three systems of SiO₂, P₂O₅-SiO₂ and B₂O₃-P₂O₅-SiO₂ is also described to estimate the onset of sintering temperature. The OH absorption measurements are performed to try to identify incorporation of hydroxyl contaminants in the systems of P₂O₅-SiO₂ and B₂O₃-P₂O₅-SiO₂.     

Ba2ZnZCo2-ZFe12O22-SiO_2微晶玻璃陶瓷的sol-gel合成及性能研究

采用柠檬酸sol-gel工艺合成了Ba₂Zn_ZCo_2-zFe₁₂O₂₂-SiO₂微晶玻璃陶瓷;采用XRD、SEM对其相成分、显微结构进行了分析,结果表明,1200°C/5h得到的Ba₂Zn_ZCo_2-zFe₁₂O₂₂-SiO₂微晶玻璃陶瓷的平均晶粒尺寸在0.3μm左右;采用HP8753E网络分析仪测定了微晶玻璃陶瓷在100MHz～6GHz范围内的介电常数及其磁导率,其复介电常数值、磁导率实部都随测试频率的增加而减小,其磁导率虚部～f曲线上显示出明显的自然共振峰。