Methanol steam reforming in an Al2O3 supported thin Pd-layer membrane reactor over Cu/ZnO/Al2O3 catalyst

In this experimental study, a membrane reactor housing a composite membrane constituted by a thin Pd-layer supported onto Al₂O₃ is utilized to perform methanol steam reforming reaction to produce high-grade hydrogen for PEM fuel cell applications. The influence of various parameters such as temperature, from 280 to 330 °C, and pressure, from 1.5 to 2.5 bar, is analyzed. A commercial Cu/Zn-based catalyst is packed in the annulus of the membrane reactor and the experimental tests are performed at space velocity equal to 18,500 h⁻¹ and H₂O:CH₃OH feed molar ratio equal to 2.5:1. Results in terms of methanol conversion, hydrogen recovery, hydrogen yield and products selectivities are given. As a best result of this work, 85% of methanol conversion and a highly pure hydrogen stream permeated through the membrane with a CO content lower than 10 ppm were reached at 330 °C and 2.5 bar. Furthermore, a comparison between the experimental results obtained in this work and literature data is proposed and discussed.     

Oxidative steam reforming of methanol over CuO/ZnO/CeO2/ZrO2/Al2O3 catalysts

The composition (CuO/ZnO/Al₂O₃ = 30/60/10) of a commercial catalyst G66B was used as a reference for designing CuO/ZnO/CeO₂/ZrO₂/Al₂O₃ catalysts for the oxidative (or combined) steam reforming of methanol (OSRM). The effects of Al₂O₃, CeO₂ and ZrO₂ on the OSRM reaction were clearly identified. CeO₂, ZrO₂ and Al₂O₃ all promoted the dispersions of CuO and ZnO in CuO/ZnO/CeO₂/ZrO₂/Al₂O₃ catalysts. Aluminum oxide lowered the reducibility of the catalyst, and weakened the OSRM reaction. Cerium oxide increased the reducibility of the catalyst, but weakened the reaction. Zirconium oxide improved the reducibility of the catalyst, and promoted the reaction. A lower CuO/ZnO ratio of the catalyst was associated with greater promotion of ZrO₂. The critical CuO/ZnO ratio for the promotion of ZrO₂ was approximately 0.75–0.8. Introducing of ZrO₂ into CuO/ZnO/Al₂O₃ also improved the stability of the catalyst. Although Al₂O₃ inhibited the OSRM reaction, a certain amount of it was required to ensure the stability and the mechanical strength of the catalysts.     

Effect of Al2O3 content on the adsorptive properties of Cu/ZnO/Al2O3 for removal of odorant sulfur compounds

Cu/ZnO/Al₂O₃ adsorbents for removal of odorant sulfur compounds were prepared with various Al/Cu molar ratios by co-precipitation method. The sulfur removing ability as a function of Al/Cu molar ratio of the adsorbents for t-butyl mercaptan (TBM), tetrahydro thiophene (THT), dimethyl disulfide (DMS) and H₂S were investigated at 250 °C and 6000 h⁻¹ space velocity. Based on the results of adsorption capacity and characterization by various techniques, the optimum Al/Cu ratio for maximum sulfur removal capacity is found to be at Al/Cu molar ratio of 0.15 which possesses the well-dispersed Cu species with high reducibility. The adsorption capacity is highest for H₂S followed by TBM, DMS and THT. The main role of Al₂O₃ component is to provide the dispersion of CuO species homogeneously with small particle formation and high reducibility.     

Fuel cell grade hydrogen production via methanol steam reforming over CuO/ZnO/Al2O3 nanocatalyst with various oxide ratios synthesized via urea-nitrates combustion method

Hydrogen production via steam reforming of methanol has been studied over a series of CuO/ZnO/Al₂O₃ catalysts synthesized by the combustion method using urea as fuel. Furthermore, the effect of alumina loading on the properties of the catalyst has been investigated. XRD analysis illustrated the crystallinity of the Cu and Zn oxides decreases by enhancing alumina loading. BET showed the surface area improvement and FESEM images revealed lower size distribution by increasing the amount of alumina. EDX results gave approximately the same metal oxide compositions of primary gel for the surface of the nanocatalysts. Catalytic performance tests showed the well practicability of catalysts synthesized by the combustion method for steam reforming of methanol process. Alumina addition to the CuO/ZnO catalyst caused the higher methanol conversion and the lower CO generation. Among different compositions the sample with molar component of CuO/ZnO/Al₂O₃ = 4/4/2.5 showed the best performance which without CO generation at 240 °C its methanol conversion decreased from 90 to 60% after 90 h.     

Nickel catalysts supported on ZrO2, Y2O3-stabilized ZrO2 and CaO-stabilized ZrO2 for the steam reforming of ethanol: Effect of the support and nickel load

Catalysts with various nickel loads were prepared on supports of ZrO₂, ZrO₂–Y₂O₃ and ZrO₂–CaO, characterized by XRD and TPR and tested for activity in ethanol steam reforming. XRD of the supports identified the monoclinic crystalline phase in the ZrO₂ and cubic phases in the ZrO₂–Y₂O₃ and ZrO₂–CaO supports. In the catalysts, the nickel impregnated on the supports was identified as the NiO phase. In the TPR analysis, peaks were observed showing the NiO phase having different interactions with the supports. In the catalytic tests, practically all the catalysts achieved 100% ethanol conversion, H₂ yield was near 70% and the gaseous concentrations of the other co-products varied in accordance with the equilibrium among them, affected principally by the supports. It was observed that when the ZrO₂ was modified with Y₂O₃ and CaO, there were big changes in the CO and CO₂ concentrations, which were attributed to the rise in the number of oxygen vacancies, permitting high-oxygen mobility and affecting the gaseous equilibrium. The liquid products analysis showed a low selectivity to liquid co-products during the reforming reactions.     

Reforming of bioethanol over Ni/Al2O3 and Ni/CeZrO2/Al2O3 catalysts in supercritical water for hydrogen production

Bioethanol was reformed in supercritical water (SCW) at 500 °C and 25 MPa on Ni/Al₂O₃ and Ni/CeZrO₂/Al₂O₃ catalysts to produce high-pressure hydrogen. The results were compared with non-catalytic reactions. Under supercritical water and in a non-catalytic environment, ethanol was reformed to H₂, CO₂ and CH₄ with small amounts of CO and C2 gas and liquid products. The presence of either Ni/Al₂O₃ or Ni/CeZrO₂/Al₂O₃ promoted reactions of ethanol reforming, dehydrogenation and decomposition. Acetaldehyde produced from the decomposition of ethanol was completely decomposed into CH₄ and CO, which underwent a further water-gas shift reaction in SCW. This led to great increases in ethanol conversion and H₂ yield on the catalysts of more than 3-4 times than that of the non-catalytic condition. For the catalytic operation, adding small amounts of oxygen at oxygen to ethanol molar ratio of 0.06 into the feed improved ethanol conversion, at the expense of some H₂ oxidized to water, resulting in a slightly lower H₂ yield. The ceria-zirconia promoted catalyst was more active than the unpromoted catalyst. On the promoted catalyst, complete ethanol conversion was achieved and no coke formation was found. The ceria-zirconia promoter has important roles in improving the decomposition of acetaldehyde, the enhancement of the water-gas shift as well as the methanation reactions to give an extremely low CO yield and a tremendously high H₂/CO ratio. The SCW environment for ethanol reforming caused the transformation of gamma-alumina towards the corundum phase of the alumina support in the Ni/Al₂O₃ catalyst, but this transformation was slowed down by the presence of the ceria-zirconia promoter.     

Non-thermal plasma assisted synthesis and physicochemical characterizations of Co and Cu doped Ni/Al2O3 nanocatalysts used for dry reforming of methane

Ni/Al₂O₃ nanocatalysts doped with Co and Cu were prepared by co-impregnation and modified by non-thermal plasma. The nanocatalysts were characterized by XRD, FESEM, TEM, EDX dot-mapping, BET, FTIR, TGA-DTG, and XPS analysis. According to XRD and XPS results, good interaction between active phase and support can be observed in both Ni–Co/Al₂O₃ and Ni–Cu/Al₂O₃ nanocatalysts. A uniform morphology, high surface area, and well dispersed particles of active sites in Ni–Co/Al₂O₃ nanocatalyst were observed that shows the effect of cobalt in controlling Ni ensemble size. In contrast Ni–Cu/Al₂O₃ nanocatalyst had no homogenous dispersion of active phase due to sintering of copper particles. The activity measurements illustrated better Ni–Co/Al₂O₃ nanocatalyst activity in comparison to Ni/Al₂O₃ and Ni–Cu/Al₂O₃ in terms of CH₄ and CO₂ conversion. H₂ and CO yield were higher for Ni–Co/Al₂O₃ and higher H₂/Co ratio was obtained as well. Whereas Ni/Al₂O₃ and Ni–Co/Al₂O₃ did not experience deactivation, Ni–Cu/Al₂O₃ suffered from activity loss by ca. 22% and 16% for CH₄ and CO₂ conversion, respectively. Sintering most likely happened in Ni–Cu/Al₂O₃ nanocatalyst due to high temperature of calcination while cobalt by controlling the size of Ni particles, alternated the size of active sites to a size range in which carbon formation was suppressed. Ni/Al ratio from XPS analysis which signifies Ni dispersion on alumina support was 5.15, 9.16, and 6.35 for Ni/Al₂O₃, Ni–Co/Al₂O₃, and Ni–Cu/Al₂O₃ nanocatalysts respectively. The highest ratio of Ni/Al was for Ni–Co/Al₂O₃ nanocatalyst that shows the best coverage of support by Ni active phase in this nanocatalyst.     

Catalytic properties of Ag promoted ZnO/Al2O3 catalysts for hydrogen production by steam reforming of ethanol

Ag promoted ZnO/Al₂O₃ catalysts were prepared by using the incipient wetness impregnation method. The catalytic properties of steam reforming reaction for hydrogen production on the prepared catalysts were evaluated with H₂O:C₂H₅OH molar ratios of 3:1 at 450 °C and atmospheric pressure. Ag promoted ZnO/Al₂O₃ catalysts show higher SRE catalytic activity than ZnO/Al₂O₃ catalysts. H₂ and CH₃CHO are the major products on Ag promoted catalysts, and C₂H₄ is also produced probably due to acid sites on Al₂O₃. SRE mechanism on Ag promoted ZnO/Al₂O₃ catalysts, which contains C-C scission, is different from that on ZnO/Al₂O₃ catalysts. A method based on thermogravimetry (TG), differential scanning calorimetry (DSC) and mass spectrometry (MS) was used to analysis the coking behavior on catalyst surface. The surfaces of Ag promoted ZnO/Al₂O₃ catalysts show two different types of coking, and suffer higher coke deposition during the steam reforming reaction.     

Hydroprocessing of Jatropha oil over NiMoCe/Al2O3 catalyst

The non-sulfided NiMoCe/Al₂O₃ catalyst was developed to produce green diesel from the hydroprocessing of Jatropha oil. The NiMoCe/Al₂O₃ catalysts were prepared by impregnation and characterized by N₂-BET, SEM, XRD and TPD-H_ads techniques. The straight chain alkanes ranging from C15 to C18 were the main components in product oil. The maximum yield of C15-C18 alkanes of 80%, selectivity of 90% and conversion of 89% were obtained at 370 °C, 3.5 MPa and 0.9 h⁻¹. Influence of reaction temperature (280–400 °C) and reaction time (10–163 h) on the composition of product oil were discussed. The experimental results demonstrated that a suitable amount of metal Ce doping on the NiMo/Al₂O₃ catalyst presented stable catalytic performance and enhanced Jatropha oil conversion as well as C15-C18 fraction selectivity.     

Evaluation of Ni/Y2O3/Al2O3 catalysts for hydrogen production by autothermal reforming of methane

Ni/xY₂O₃–Al₂O₃ (x = 5, 10, 15, 20 wt%) catalysts were prepared by sequential impregnation synthesis. The catalytic performance for the autothermal reforming of methane was evaluated and compared with Ni/γ-Al₂O₃ catalyst. The physicochemical properties of catalysts were characterized by X-ray diffraction (XRD), Transmission electron microscope (TEM), X-Ray Photoelectron Spectrometer (XPS), Thermo Gravimetric Analyzer (TGA) and H₂-temperature programmed reduction techniques (TPR). The decrease of nickel particle size and the change of reducibility were found with Y modification. The CH₄ conversion increased with elevating levels of Y₂O₃ from 5% to 10%, then decreased with Y content from 10% to 20%. Ni/xY₂O₃–Al₂O₃ catalysts maintained high activity after 24 h on stream, while Ni/Al₂O₃ had a significant deactivation. The characterization of spent catalysts indicated that the addition of Y retarded Ni sintering and decreased the amount of coke.     

Hydrogen production by oxidative steam reforming of methanol over Ni/CeO2–ZrO2 catalysts

Single ZrO₂ and mixed CeO₂-ZrO₂ oxides with different CeO₂/ZrO₂ ratios were prepared by the sol-gel method and the CeO₂ by precipitation. The prepared support were impregnated with an aqueous solution of NiCl₂·6H₂O at an appropriate concentration to yield 3 wt.% of nickel respectively in the catalysts. Catalytic materials were characterized by BET (N₂ adsorption-desorption), SEM-EDS, XRD and TPR. The oxidative steam reforming of methanol (OSRM) reaction was investigated on these catalysts for H₂ production as a function of temperature. Depending of the CeO₂/ZrO₂ ratio; the catalysts composition has a significant influence on the surface area (BET), reduction properties and methanol conversion. XRD patterns of the Ni-base catalysts showed well defined diffraction peaks of the metallic Ni except on the Ni/CeO₂ catalyst, suggesting that on this sample all of the active phase was highly dispersed. Ni/Ceria-rich catalysts were vastly active for OSRM, giving a total CH₃OH conversion at 325 °C with GHSV = 0.3 × 10⁵ h⁻¹. They also showed close selectivity toward H₂, with high selectivity to CO₂ in all range of temperatures, this suggests that the reverse WGS reaction does not occur on these samples. It seems that the nickel is the phase mainly responsible of hydrogen production although the CeO₂/ZrO₂ support reduces the CO formation.     

Hydrogen production by steam reforming of model bio-oil using structured Ni/Al2O3 catalysts

This study focuses on hydrogen production from the steam reforming of model bio-oil over Ni/Al₂O₃ catalysts prepared in two different geometries (monolith and pellet) using the dip-coating and wet impregnation methods and characterized using Powder X-Ray diffraction, Temperature Programmed Reduction, Scanning Electron Microscopy (SEM) and BET Surface area analysis. The effects of the catalyst geometry and reforming temperatures were studied by carrying out experiments at the optimal conditions of T = (823, 923, 1023) K and S/C ratio = 13 determined from the thermodynamic analysis of the process prior to the experiments using the process simulator PRO-II. The experimental results showed high steady state H₂ yield corresponding to 2.58 and 1.73 mol (out of 5.13 mol) using monolithic and the pelletized catalysts respectively. The product distribution achieved with the monolithic catalyst was closer to the thermodynamic results suggesting a higher selectivity to hydrogen production.     

Photocatalytic hydrogen production from aqueous methanol solution with CuO/Al2O3/TiO2 nanocomposite

The photocatalytic hydrogen production from aqueous methanol solution was investigated with ZnO/TiO₂, SnO/TiO₂, CuO/TiO₂, Al₂O₃/TiO₂ and CuO/Al₂O₃/TiO₂ nanocomposites. A mechanical mixing method, followed by the solid-state reaction at elevated temperature, was used for the preparation of nanocomposite photocatalyst. Among these nanocomposite photocatalysts, the maximal photocatalytic hydrogen production was observed with CuO/Al₂O₃/TiO₂ nanocomposites. A variety of components of CuO/Al₂O₃/TiO₂ photocatalysts were tested for the enhancement of H₂ formation. The optimal component was 0.2 wt% CuO/0.3 wt% Al₂O₃/TiO₂. The activity exhibited approximately tenfold enhancement at the optimum loading, compared with that with pure P-25 TiO₂. Nano-sized TiO₂ photocatalytic hydrogen technology has great potential for low-cost, environmentally friendly solar-hydrogen production to support the future hydrogen economy.     

Selective CO oxidation on Cu promoted Pt/Al2O3 and Pt/Nb2O5 catalysts

Pt–Cu catalysts supported on Al₂O₃ and Nb₂O₅ were studied for use in selective CO oxidation. The addition of copper enhanced the activity and selectivity of Pt–Cu/Nb₂O₅ at lower temperatures when compared to Pt/Nb₂O₅. On the other hand, copper addition was not beneficial in the case of Al₂O₃ supported catalysts.     

Development of durable copper catalyst for hydrogen production by high temperature methanol steam reforming

Highly durable catalyst for high temperature methanol steam reforming is required for a compact hydrogen processor. Deactivation of a coprecipitated Cu/ZnO/ZrO₂ catalyst modified with In₂O₃ is very gradual even in the high temperature methanol steam reforming mainly at 500 °C, but the initial activity is considerably low. Addition of Y₂O₃ to Cu/ZnO/ZrO₂/In₂O₃ increases its initial activity due to the higher Cu surface amount, while the activity comes gradually close to that for the catalyst without Y₂O₃ during the reaction. Coprecipitation of Cu/ZnO/ZrO₂/Y₂O₃/In₂O₃ on a zirconia support triply increases the overall activity by keeping the durability while the amount of the coprecipitated portion is a half of that without the support. On the composite catalyst, sintering of Cu particles is suppressed. The surface Cu amount is similar to that without the support, but the Cu surface activity is much higher probably because of the small Cu particle size.     

Influence of CuO/ZnO/Al2O3 wash-coating slurries on the steam reforming reaction of methanol

A micro-channel reactor for methanol steam reforming is a candidate to supply hydrogen on-site to fuel cells. Micro-channel beds wash-coated with poor quality slurry formulations lead to poorer performance than packed beds using pellet catalysts. This study explored the morphology, X-ray Diffraction (XRD) spectrum, BET surface area and activity of wash-coating catalyst layers from a series of catalyst slurries. All catalyst slurries were prepared from the commercial MDC-3 catalyst. Hydrogen production using wash-coating catalyst layers was performed under packed bed conditions. The results reveal that the solubility level of the MDC-3 catalyst during the slurry preparation process affected the activity of methanol steam reforming. It is difficult to reconstruct the original fine structure, as the MDC-3 catalyst had a higher solubility status after slurry preparation. The volume of the micro-channel catalyst bed was approximately 0.3 cm³. It can supply hydrogen to fuel cells that can produce approximately 8 W with 80% H₂ utilization and 60% fuel cell efficiency.     

Effects of modifying Ni/Al2O3 catalyst with cobalt on the reforming of CH4 with CO2 and cracking of CH4 reactions

Alumina supported nickel (Ni/Al₂O₃), nickel–cobalt (Ni–Co/Al₂O₃) and cobalt (Co/Al₂O₃) catalysts containing 15% metal were synthesized, characterized and tested for the reforming of CH₄ with CO₂ and CH₄ cracking reactions. In the Ni–Co/Al₂O₃ catalysts Ni–Co alloys were detected and the surface metal sites decreased with decrease in Ni:Co ratio. Turnover frequencies of CH₄ were determined for both reactions. The initial turnover frequencies of reforming (TOF_DRM) for Ni–Co/Al₂O₃ were greater than that for Ni/Al₂O₃, which suggested a higher activity of alloy sites. The initial turnover frequencies for cracking (TOF_CRK) did not follow this trend. The highest average TOF_DRM, H₂:CO ratio and TOF_CRK were observed for a catalyst containing a Ni:Co ratio of 3:1. This catalyst also had the maximum carbon deposited during reforming and produced the maximum reactive carbon during cracking. It appeared that carbon was an intermediate product of reforming and the best catalyst was able to most effectively crack CH₄ and oxidize carbon to CO by CO₂.     

Surface modification of solution combustion synthesized Ni/Al2O3 catalyst for aqueous-phase reforming of ethanol

The effect of surface modification of an alumina powder supported nano-scale nickel catalyst used in aqueous-phase reforming of ethanol has been explored in this paper. The Al₂O₃ powder was prepared by a solution combustion synthesis (SCS) route and the surface of the powder was modified by a non-thermal RF plasma treatment using nitrogen gas. Catalysts were coated by an impregnation method. The performances of the unmodified and modified Ni/Al₂O₃ catalysts have been compared from a catalytic activity, selectivity, and microstructural point of view. The catalytic activity results showed that while nature, relative ratio and selectivity of the products both in gas and liquid effluents did not change, catalytic activity (in terms of EtOH conversion and H₂ yield per g) of the sample increased after plasma modification. Microstructural (XRD, surface area) analysis showed that phase content and surface area of unmodified and modified catalysts are similar, while TEM and H₂-chemisorption showed higher metal surface area, higher metal dispersion and lower active metal particle size for the modified sample compared to the unmodified sample. The temperature programmed reduction (TPR) analysis demonstrated stronger support-metal interaction and smaller NiO particles for the modified catalyst at lower heat treatment temperature. The temperature programmed desorption (TPD) of ammonia analysis showed stronger acidity for the modified support, which can explain better dispersion of the metal particles on the modified catalyst compared to the unmodified sample.     

Effect of Pr addition on the properties of Ni/Al2O3 catalysts with an application in the autothermal reforming of methane

Ni/xPr-Al₂O₃ (x = 5, 10, 15, 20 wt%) catalysts with an application in autothermal reforming of methane were prepared by sequential impregnation synthesis; its catalytic performance was evaluated and compared with that of Ni/γ-Al₂O₃ catalyst; the physicochemical properties of the catalysts were characterized by X-ray diffraction (XRD), Transmission electron microscope (TEM), X-Ray Photoelectron Spectrometer (XPS), Thermo Gravimetric Analyzer (TGA) and H₂-temperature programmed reduction techniques (TPR). The results showed that Pr addition promoted the reduction of nickel particle size on the surface. TPR experiments suggested a heterogeneous distribution of nickel oxide particles over xPr-Al₂O₃ supports and the promotion of NiO reduction by Pr modification. The CH₄ conversion increased with elevating levels of Pr addition from 5% to 10%, then decreased with Pr content from 10% to 20%. For the stability catalytic tests, Ni/xPr-Al₂O₃ catalysts maintained the high activity after 48 h while Ni/Al₂O₃ had a significant deactivation.     

Steam reforming and oxidative steam reforming of methanol over CuO–CeO2 catalysts

Steam reforming (SRM) and oxidative steam reforming of methanol (OSRM) were carried out over a series of coprecipitated CuO–CeO₂ catalysts with varying copper content in the range of 30–80 at.% Cu (= 100 × Cu/(Cu + Ce)). The effects of copper content, reaction temperature and O₂ concentration on catalytic activity were investigated. The activity of CuO–CeO₂ catalysts for SRM and OSRM increased with the copper content and 70 at.% CuO–CeO₂ catalyst showed the highest activity in the temperature range of 160–300 °C for both SRM and OSRM. After SRM or OSRM, the copper species in the catalysts observed by XRD were mainly metallic copper with small amount of CuO and Cu₂O, an indication that metallic copper is an active species in the catalysis of both SRM and OSRM. It was observed that the methanol conversion increased considerably with the addition of O₂ into the feed stream, indicating that the partial oxidation of methanol (POM) is much faster than SRM. The optimum 70 at.% CuO–CeO₂ catalyst showed stable activities for both SRM and OSRM reactions at 300 °C.