Low metal content Co and Ni alumina supported catalysts for the CO2 reforming of methane

Low metal content Co and Ni alumina supported catalysts (4.0, 2.5 and 1.0 wt% nominal metal content) have been prepared, characterized (by ICP-OES, TEM, TPR-H₂ and TPO) and tested for the CO₂ reforming of methane. The objective is to optimize the metal loading in order to have a more efficient system. The selected reaction temperature is 973 K, although some tests at higher reaction temperature have been also performed. The results show that the amount of deposited carbon is noticeably lower than that obtained with the Co and Ni reference catalysts (9 wt%), but the CH₄ and CO₂ conversions are also lower. Among the catalysts tested, the Co(1) catalyst (the value in brackets corresponds to the nominal wt% loading) is deactivated during the first minutes of reaction because CoAl₂O₄ is formed, while Ni(1) and Co(2.5) catalysts show a high specific activity for methane conversion, a high stability and a very low carbon deposition.     

CO2 reforming of methane over Pt-Ni/Al2O3 catalysts: Effects of catalyst composition, and water and oxygen addition to the feed

A series of Pt-Ni bimetallic catalysts supported on δ-Al₂O₃ to be used in carbon dioxide reforming of methane was prepared and tested with the objective of optimizing the Ni/Pt metal composition to obtain high activity and stability. Selected catalyst samples, before and after reaction, were characterized by XRD, XPS, TGA/DTA and SEM-EDS. The activity results showed that the catalytic performance of bimetallic Pt-Ni samples strongly depended on the metal loadings and Ni/Pt loading ratio. Among all the catalysts, 0.3%Pt-10%Ni/Al₂O₃, which has the lowest Ni/Pt ratio, exhibited the highest catalytic activity and stability. The combined characterization and catalyst performance tests results reveal that low Ni/Pt molar loading ratio of 0.3%Pt-10%Ni/Al₂O₃ sample led to a relatively easy reduction of nickel oxide species and smaller nano-sized nickel particles having better dispersion caused by the intimate interaction between Pt and Ni sites in the closed vicinity. The changes in the catalysts’ activity and stability under the presence of an additional oxygen source were determined through addition of small amounts of either oxygen or water vapor to the feed stream. The results of the combined dry reforming and partial oxidation tests strongly indicated a change in surface reaction mechanism depending on the Pt load and Ni/Pt ratio of the catalysts. 0.3Pt-10Ni was capable of operating under a variety of feed conditions without significant deactivation suggesting that the catalyst is very promising for synthesis gas production for gas-to-liquid technology.     

Catalytic conversion of CH4 and CO2 to synthesis gas on Ni/SiO2 catalysts containing Gd2O3 promoter

A series of Ni/SiO₂ catalysts containing different amounts of Gd₂O₃ promoter was prepared, characterized by H₂-adsorption and XRD, and used for carbon dioxide reforming of methane (CRM) and methane autothermal reforming with CO₂ + O₂ (MATR) in a fluidized-bed reactor. The results of pulse surface reactions showed that Ni/SiO₂ catalysts containing Gd₂O₃ promoter could increase the activity for CH₄ decomposition, and Raman analysis confirmed that reactive carbon species mainly formed on the Ni/SiO₂ catalysts containing Gd₂O₃ promoter. In this work, it was found that methane activation and reforming reactions proceeded according to different mechanisms after Gd₂O₃ addition due to the formation of carbonate species. In addition, Ni/SiO₂ catalysts containing Gd₂O₃ promoter demonstrated higher activity and stability in both CRM and MATR reactions in a fluidized bed reactor than Ni/SiO₂ catalysts without Gd₂O₃ even at a higher space velocity.     

Fuel cell grade hydrogen production via methanol steam reforming over CuO/ZnO/Al2O3 nanocatalyst with various oxide ratios synthesized via urea-nitrates combustion method

Hydrogen production via steam reforming of methanol has been studied over a series of CuO/ZnO/Al₂O₃ catalysts synthesized by the combustion method using urea as fuel. Furthermore, the effect of alumina loading on the properties of the catalyst has been investigated. XRD analysis illustrated the crystallinity of the Cu and Zn oxides decreases by enhancing alumina loading. BET showed the surface area improvement and FESEM images revealed lower size distribution by increasing the amount of alumina. EDX results gave approximately the same metal oxide compositions of primary gel for the surface of the nanocatalysts. Catalytic performance tests showed the well practicability of catalysts synthesized by the combustion method for steam reforming of methanol process. Alumina addition to the CuO/ZnO catalyst caused the higher methanol conversion and the lower CO generation. Among different compositions the sample with molar component of CuO/ZnO/Al₂O₃ = 4/4/2.5 showed the best performance which without CO generation at 240 °C its methanol conversion decreased from 90 to 60% after 90 h.     

H2 production by methane decomposition: Catalytic and technological aspects

Ni and Co supported on SiO₂ and Al₂O₃ silica cloth thin layer catalysts have been investigated in the catalytic decomposition of natural gas (CDNG) reaction. The influence of carrier nature and reaction temperature was evaluated with the aim to individuate the key factors affecting coke formation. Both Ni and Co silica supported catalysts, due to the low metal support interaction (MSI), promotes the formation of carbon filament with particles at tip. On the contrary, in case alumina was used as support, metals strongly interact with surface thus depressing both the metal sintering and the detachment of particles from catalyst surface. In such cases, carbon grows on metal particle with a “base mechanism” while particles remain well anchored on the catalyst surface. This allowed to realize a cyclic dual-step process based on methane decomposition and catalyst oxygen regeneration without deactivation of catalyst. Technological considerations have led to conclude that the implement of a process based on decomposition and regeneration of catalyst by oxidation requires the development of a robust catalytic system characterized by both a strong MSI and a well defined particle size distribution. In particular, the catalyst should be able to operate at high temperature, necessary to reach high methane conversion values (> 90%), avoiding at the same time the formation of both the carbon filaments with metal at tip or the encapsulating carbon which drastically deactivate the catalyst.     

Combined catalytic partial oxidation and CO2 reforming of methane over ZrO2-modified Ni/SiO2 catalysts using fluidized-bed reactor

Nickel on zirconium-modified silica was prepared and tested as a catalyst for reforming methane with CO₂ and O₂ in a fluidized-bed reactor. A conversion of CH₄ near thermodynamic equilibrium and low H₂/CO ratio (1<H₂/CO<2) were obtained without catalyst deactivation during 10 h, in a most energy efficient and safe manner. A weight loading of 5 wt% zirconium was found to be the optimum. The catalysts were characterized using X-ray diffraction (XRD), H₂-temperature reaction (H₂-TPR), CO₂-temperature desorption (CO₂-TPD) and transmission election microscope (TEM) techniques. Ni sintering was a major reason for the deactivation of pure Ni/SiO₂ catalysts, while Ni dispersed highly on a zirconium-promoted Ni/SiO₂ catalyst. The different kinds of surface Ni species formed on ZrO₂-promoted catalysts might be responsible for its high activity and good resistance to Ni sintering.     

Nickel on a macro-mesoporous Al2O3@ZrO2 core/shell nanocomposite as a novel catalyst for CO methanation

A novel nickel catalyst supported on Al₂O₃@ZrO₂ core/shell nanocomposites was prepared by the impregnation method. The core/shell nanocomposites were synthesized by depositing zirconium species on boehmite nanofibres. This contribution aims to study the effects of the pore structure of supports and the zirconia dispersed on the surface of the alumina nanofibres on the CO methanation. The catalysts and supports were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), H₂ temperature-programmed reduction (H₂-TPR), nitrogen adsorption–desorption, and thermogravimetry and differential thermal analysis (TG-DTA). The catalytic performance of the catalysts for CO methanation was investigated at a temperature range from 300 °C to 500 °C. The results of the characterization indicate that the metastable tetragonal zirconia could be stably and evenly dispersed on the surface of alumina nanofibres. The interlaced nanorods of the Al₂O₃@ZrO₂ core/shell nanocomposites resulted in a macropore structure and the spaces between the zirconia nanoparticles dispersed on the alumina nanofibres formed most of the mesopores. Zirconia on the surface of the support promoted the dispersion and influenced the reduction states of the nickel species on the support, so it prevented the nickel species from sintering as well as from forming a spinel phase with alumina at high temperatures, and thus reduced the carbon deposition during the reaction. With the increase of the zirconia content in the catalyst, the catalytic performance for the CO methanation was enhanced. The Ni/Al₂O₃@ZrO₂-15 exhibited the highest CO conversion and methane selectivity at 400 °C, but they decreased dramatically above or below 400 °C due to the temperature sensitivity of the catalyst. Ni/Al₂O₃@ZrO₂-30 exhibited a high and constant rate of methane formation between 350 °C and 450 °C. The excellent catalytic performance of this catalyst is attributed to its reasonable pore structure and good dispersion of zirconia on the support. This catalyst has great potential to be further studied for the future industrial use.     

Ni/Al2O3 catalysts for CO2 methanation: Effect of silica and nickel loading

Samples containing from 1 to 33 wt.% of NiO on silica and alumina doped with silica (1 and 20 wt.% silica in the support) have been prepared and characterized by BET, XRD, FT-IR, UV–vis–NIR, FE-SEM, EDXS, and TPR techniques. Catalysts have been pre-reduced in situ before catalytic experiments and data have been compared with Ni/Al₂O₃ reference sample. Characterization results showed that SiO₂ support has a low Ni dispersion ability mainly producing segregated NiO particles and a small amount of dispersed Ni²⁺ in exchange sites. Instead, for the Si-doped alumina a “surface spinel monolayer phase” is formed by increasing Ni loading and, only when the support surface is completely covered by this layer, NiO is formed. Moreover, H₂-TPR results indicated that NiO particles are more easily reduced compared to Ni species. Low loading Ni/SiO₂ catalysts show high selectivity and moderate activity for RWGS (reverse Water Gas Shift) reaction, likely mainly due to nickel species dispersed in silica exchange sites, as evidenced by visible spectroscopy. High loading Ni/SiO₂ catalysts show both methanation and RWGS but evident short-term deactivation for methanation, attributed to large, segregated Ni metal particles, covered by a carbon veil. Ni on alumina -rich carriers, where nickel disperses forming a surface spinel phase, show high activity and selectivity for methanation, and short-term catalyst stability as well. This activity is attributed to small nickel clusters or metal particles interacting with alumina, formed upon reaction. The addition of SiO₂ in Al₂O₃ support decreases the activity of Ni catalysts in CO₂ methanation, because it reduces the ability of the support to disperse nickel in form of the surface spinel phase, thus reducing the amount of Ni clusters in the reduced catalysts.     

Synthesis gas production in the combined CO2 reforming with partial oxidation of methane over Ce-promoted Ni/SiO2 catalysts

A series of nickel-based catalyst supported on silica (Ni/SiO₂) with different loading of Ce/Ni (molar ratio ranging from 0.17 to 0.84) were prepared using conventional co-impregnation method and were applied to synthesis gas production in the combination of CO₂ reforming with partial oxidation of methane. Among the cerium-containing catalysts, the cerium-rich ones exhibited the higher activity and stability than the cerium-low ones. The temperature-programmed reduction (TPR) and UV–vis diffuse reflectance spectroscopy (UV–vis DRS) analysis revealed that the addition of CeO₂ reduced the chemical interaction between Ni and support, resulting in an increase in reducibility and dispersion of Ni. Over NiCe-x/SiO₂ (x = 0.17, 0.50, 0.67, 0.84) catalysts, the reduction peak in TPR profiles shifted to the higher temperature with increasing Ce/Ni molar ratio, which was attributed to the smaller metallic nickel size of the reduced catalysts. The transmission electron microscopy (TEM) and X-ray diffraction (XRD) for the post-reaction catalysts confirmed that the promoter retained the metallic nickel species and prevented the metal particle growth at high reaction temperature. The NiCe-0.84/SiO₂ catalyst with small Ni particle size exhibited the stable activity with the constant H₂/CO molar ratio of 1.2 during 6-h reaction in the combination of CO₂ reforming with partial oxidation of methane at 850 °C and atmospheric pressure.     

Nanocomposite Ni/ZrO2: Highly active and stable catalyst for H2 production via cyclic stepwise methane reforming reactions

This work investigates the catalytic performance of nanocomposite Ni/ZrO₂-AN catalyst consisting of comparably sized Ni (10–15 nm) and ZrO₂ (15–25 nm) particles for hydrogen production from the cyclic stepwise methane reforming reaction with either steam (H₂O) or CO₂ at 500–650 °C, in comparison with a conventional Ni/ZrO₂-CP catalyst featuring Ni particles supported by large and widely sized ZrO₂ particles (20–400 nm). Though both catalysts exhibited similar activity and stability during the reactions at 500 and 550 °C, they showed remarkably different catalytic stabilities at higher temperatures. The Ni/ZrO₂-CP catalyst featured a significant deactivation even during the methane decomposition step in the first cycle of the reactions at ≥600 °C, but the Ni/ZrO₂-AN catalyst showed a very stable activity during at least 17 consecutive cycles in the cyclic reaction with steam. Changes in the catalyst beds at varying stages of the reactions were characterized with TEM, XRD and TPO–DTG and were correlated with the amount and nature of the carbon deposits. The Ni particles in Ni/ZrO₂-AN became stabilized at the sizes of around 20 nm but those in Ni/ZrO₂-CP kept on growing in the methane decomposition steps of the cyclic reaction. The small and narrowly sized Ni particles in the nanocomposite Ni/ZrO₂-AN catalyst led to a selective formation of filamentous carbons whereas the larger Ni particles in the Ni/ZrO₂-CP catalyst a preferred formation of graphitic encapsulating carbons. The filamentous carbons were favorably volatilized in the steam treatment step but the CO₂ treatment selectively volatilized the encapsulating carbons. These results identify that the nature but not the amount of carbon deposits is the key to the stability of Ni/ZrO₂ catalyst and that the nanocomposite Ni/ZrO₂-AN would be a promising catalyst for hydrogen production via cyclic stepwise methane reforming reactions.     

Mesoporous zirconia-modified clays supported nickel catalysts for CO and CO2 methanation

The Ni catalysts supported on a new structure with zirconia nanoparticles highly dispersed on the partly damaged clay layers has been prepared by the incipient wetness impregnation method and the new structure of the support has been prepared in one pot by the hydrothermal treatment of the mixture of the clay suspension and the ZrO(NO₃)₂ solution. The catalytic performances for the CO and CO₂ methanation on the catalysts have been investigated at a temperature range from 300 °C to 500 °C at atmospheric pressure. The catalysts and supports have been characterized by X-ray diffraction (XRD), transmittance electron microscopy (TEM), H₂ temperature-programmed reduction (H₂-TPR), nitrogen adsorption–desorption, and thermogravimetry and differential thermal analysis (TG-DTA). It is found that the zirconia-modified clays have the typical bimodal pore size distribution. Most of the pores with the sizes smaller than 10 nm are resulted from the zirconia pillared clays and the mesopores with the sizes larger than 10 nm and the macropores with the sizes larger than 50 nm are resulted from the partly damaged clay layers. The bimodal pore structure is beneficial to the dispersion of Ni on the layers of the zirconia-modified clays and the increase in Ni loading. The zirconia nanoparticles are highly dispersed on the partly damaged clay layers. Nickel oxide in cubic phase is the only Ni species that can be detected by XRD. The nickel oxide nanoparticles with the sizes of 12 nanometers or more are well dispersed on the zirconia-modified clay layers, which are observed to be buried in the stack layers of zirconia. The presence of nickel oxide in six different forms could be perceived on the new structure. Five of them except the Ni species that forms the spinel phase with Al in clays can be reduced to the active Ni species for the CO and CO₂ methanation. But the activity of the Ni species is different, which is associated with the chemical environment at which the Ni species is located. The catalyst with the higher zirconia content, which also has the larger specific surface area and pore volume, exhibits the better catalytic performance for the CO or CO₂ methanation. Zirconia in the catalyst is responsible for the dispersion of the Ni species, and it prevents the metallic Ni nanoparticles from sintering during the process of the reaction. In addition, it is also responsible for the reduction of the inactive carbon deposition. The catalyst with 15 wt.% zirconia content has the highest CO conversion of about 100% and the highest methane selectivity of about 93% at 450 °C for CO methanation, and the catalyst with 20% zirconia content has the CO₂ conversion of about 80% and the highest methane selectivity of about 99% for CO₂ methanation at 350 °C. The catalyst with 15 wt.% zirconia possesses promising stability and no distinct deactivation could be perceived after reaction for 40 h. This new catalyst has great potential to be used in the conversion of the blast furnace gas (BFG) and the coke oven gas (COG) to methane.     

Meso–macroporous monolithic CuO–CeO2/γ/α-Al2O3 catalysts for CO preferential oxidation in hydrogen-rich gas: Effect of loading methods

Meso–macroporous alumina supported CuO–CeO₂ catalysts were prepared by citrate, urea combustion and impregnation methods. The effect of loading methods on the microstructure of the catalysts, the interaction between copper and ceria and the catalytic performance for preferential oxidation of CO in hydrogen-rich gases was investigated. The prepared monolithic catalysts were characterized by using techniques of N₂ adsorption and desorption, SEM, XRD, HRTEM and TPR. The results showed that the loading methods markedly influenced the catalyst structure and the catalytic performance. The citrate and urea combustion methods favored the formation of the interaction between copper and ceria. Compared with the urea combustion method, the citrate method led to smaller ceria particles on the alumina support. The meso–macroporous monolithic catalysts prepared by the citrate method maintained the structural characteristics of the highly active CuO–CeO₂ catalysts, and showed good catalytic performance in CO preferential oxidation in the simulated reformate gases containing water and CO₂.     

Surface modification of solution combustion synthesized Ni/Al2O3 catalyst for aqueous-phase reforming of ethanol

The effect of surface modification of an alumina powder supported nano-scale nickel catalyst used in aqueous-phase reforming of ethanol has been explored in this paper. The Al₂O₃ powder was prepared by a solution combustion synthesis (SCS) route and the surface of the powder was modified by a non-thermal RF plasma treatment using nitrogen gas. Catalysts were coated by an impregnation method. The performances of the unmodified and modified Ni/Al₂O₃ catalysts have been compared from a catalytic activity, selectivity, and microstructural point of view. The catalytic activity results showed that while nature, relative ratio and selectivity of the products both in gas and liquid effluents did not change, catalytic activity (in terms of EtOH conversion and H₂ yield per g) of the sample increased after plasma modification. Microstructural (XRD, surface area) analysis showed that phase content and surface area of unmodified and modified catalysts are similar, while TEM and H₂-chemisorption showed higher metal surface area, higher metal dispersion and lower active metal particle size for the modified sample compared to the unmodified sample. The temperature programmed reduction (TPR) analysis demonstrated stronger support-metal interaction and smaller NiO particles for the modified catalyst at lower heat treatment temperature. The temperature programmed desorption (TPD) of ammonia analysis showed stronger acidity for the modified support, which can explain better dispersion of the metal particles on the modified catalyst compared to the unmodified sample.     

The promoting effect of La, Mg, Co and Zn on the activity and stability of Ni/SiO2 catalyst for CO2 reforming of methane

CO₂ reforming of methane into synthesis gas over Ni/SiO₂ catalysts promoted by La, Mg, Co and Zn was investigated. The catalysts were prepared by impregnation method and characterized by XRD, TPR, SEM and TG-DTA techniques. Ni-La/SiO₂ catalyst was found to exhibit high activity and excellent stability with the addition of suitable amount of La promoter, which increased the dispersion of NiO and the interaction between NiO and SiO₂. Two different types of carbon species, namely, easily oxidized carbonaceous species and inert carbon, were observed on the surface of the used catalysts. The inert carbon deposited on Ni-Mg/SiO₂ catalyst may be the main reason for its deactivation, while the principal reason for the deactivation of Ni-Co/SiO₂ catalyst might be the sintering of metallic Ni. The addition of La and Mg decreased the contribution of reverse water-gas shift reaction, leading to higher H₂ yield.     

Autothermal reforming of methane over nickel catalysts supported on nanocrystalline MgAl2O4 with high surface area

In this paper autothermal reforming of methane (ATR) was carried out over MgAl₂O₄ supported Ni catalysts with various Ni loadings. MgAl₂O₄ spinel with high specific surface area, as nanocrystalline carrier for nickel catalysts was synthesized by co-precipitation method with the addition of pluronic P123 triblock copolymer as surfactant. The prepared samples were characterized by XRD, BET, TEM, SEM, TPR and TPH techniques. The results demonstrated that methane conversion is significantly increased with increasing the Ni content and methane conversion of 15% Ni/MgAl₂O₄ was higher than that of other catalysts in all operation temperatures. Furthermore the influences of H₂O/CH₄, and O₂/CH₄ molar ratio in feed and GHSV on activity of 5% Ni/MgAl₂O₄ catalyst were investigated.     

Preparation of nickel catalysts supported on CaO.2Al2O3 for methane reforming with carbon dioxide

Nanocrystalline calcium aluminate (CaO.2Al₂O₃) was prepared by a simple co-precipitation method using Poly (ethylene glycol)-block-poly(propylene glycol)-block poly(ethylene glycol) (PEG-PPG-PEG, MW:5800) as surfactant and employed as catalyst support for nickel catalysts in methane reforming with carbon dioxide. The prepared samples were characterized by X-ray diffraction (XRD), N₂ adsorption (BET), Temperature programmed reduction and oxidation (TPR-TPO) and Scanning electron microscopy (SEM) techniques. The results showed that the prepared support has a high potential as support for nickel catalysts in methane reforming with carbon dioxide. The results showed high catalytic activity and stability for the prepared catalysts. Among the prepared catalysts 15% Ni/CaO.2Al₂O₃ was the most active catalyst and showed the highest affinity for carbon formation. In addition, 7% Ni/CaO.2Al₂O₃ possessed high catalytic stability during 50 h time on stream. The TPO analysis revealed that increasing in nickel content increased the amount of deposited carbon over the spent catalysts. SEM results detected only whisker type of carbon for all spent catalysts.     

Effects of modifying Ni/Al2O3 catalyst with cobalt on the reforming of CH4 with CO2 and cracking of CH4 reactions

Alumina supported nickel (Ni/Al₂O₃), nickel–cobalt (Ni–Co/Al₂O₃) and cobalt (Co/Al₂O₃) catalysts containing 15% metal were synthesized, characterized and tested for the reforming of CH₄ with CO₂ and CH₄ cracking reactions. In the Ni–Co/Al₂O₃ catalysts Ni–Co alloys were detected and the surface metal sites decreased with decrease in Ni:Co ratio. Turnover frequencies of CH₄ were determined for both reactions. The initial turnover frequencies of reforming (TOF_DRM) for Ni–Co/Al₂O₃ were greater than that for Ni/Al₂O₃, which suggested a higher activity of alloy sites. The initial turnover frequencies for cracking (TOF_CRK) did not follow this trend. The highest average TOF_DRM, H₂:CO ratio and TOF_CRK were observed for a catalyst containing a Ni:Co ratio of 3:1. This catalyst also had the maximum carbon deposited during reforming and produced the maximum reactive carbon during cracking. It appeared that carbon was an intermediate product of reforming and the best catalyst was able to most effectively crack CH₄ and oxidize carbon to CO by CO₂.     

Highly stable and active Ni-mesoporous alumina catalysts for dry reforming of methane

Nanostructured Ni-incorporated mesoporous alumina (MAl) materials with different Ni loading (7, 10 and 15 wt %) were prepared by a template assisted hydrothermal synthesis method and tested as catalysts for CO₂ reforming of methane under different conditions (nickel loading, gas hourly space velocity (GHSV), reaction temperature and time-on-stream (TOS)). The most active catalyst tested (Ni(10 wt%)-MAl) showed a very high stability over 200 h compared to a Ni(10 wt%)/γ-Al₂O₃ prepared using a co-precipitation method which had a significant loss in activity after only ∼4 h of testing. The high stability of the Ni-MAl materials prepared by the template assisted method was due to the Ni nanoparticles in these catalysts being highly stable towards migration/sintering under the reaction conditions used (800 °C, 52,000 mL h⁻¹ g⁻¹). The low susceptibility of the Ni nanoparticles in these catalysts to migration/sintering was most likely due to a strong Ni-support interaction and/or active metal particles being confined to the mesoporous channels of the support. The Ni-MAl catalysts also had significantly lower amounts of carbon deposited compared to the catalyst prepared using the co-precipitation method.     

Hydrogen production from methane autothermal reforming over CaTiO3, BaTiO3 and SrTiO3 supported nickel catalysts

Nickel supported on perovskite supports were investigated in the autothermal reforming of methane. The catalysts were prepared by incipient wetness impregnation and characterized by energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), N₂ physisorption, H₂ temperature programmed reduction (H₂-TPR), H₂ chemisorption, dehydrogenation of cyclohexane model reaction and Raman spectroscopy. The alumina supported catalyst exhibited highest initial conversion and selectivity to H₂, however it deactivated. All catalysts with perovskite support were very stable, with Ni/CaTiO₃ and Ni/BaTiO₃ converting over 70% of the methane. Due to carbon formation, Ni/SrTiO₃ conversion was only 50%. Turnover frequency was higher on perovskite supported catalysts. Deactivated Ni/Al₂O₃ favored total oxidation of methane instead of methane reforming, however the selectivity of catalysts supported on perovskites remained stable.     

Effect of Co-Ni ratio on the activity and stability of Co-Ni bimetallic aerogel catalyst for methane Oxy-CO2 reforming

Co-Ni bimetallic aerogel catalysts with various Co/Ni ratios were synthesized by the sol-gel method followed by the supercritical drying process. The catalysts were characterized by XRD, H₂-TPR, HRTEM, BET, TG and FESEM. It showed that the Co/Ni ratio influenced the micro-structure of the Co-Ni bimetallic aerogel catalysts. The formation of homogeneous metal alloy on the bimetallic catalysts was observed after the reduction. In addition, catalysts with higher Co/Ni ratios showed smaller active metal particle sizes. The activities of the aerogel catalysts in terms of CH₄ conversion were found to be in the order of 5Co5Ni ≈ 3Co7Ni > 7Co3Ni > 10Ni >> 10Co. 5Co5Ni exhibited the highest CH₄ conversion in methane Oxy-CO₂ reforming, which is 16% and 55% greater than those of 10Ni and 10Co, respectively. The difference between the catalytic performances could mainly be attributed to the combined effect of the kinetics, the geometric and the SMSI effects.