High temperature water gas shift reaction over promoted iron based catalysts prepared by pyrolysis method

In this work the effects of different promoters (Cr, Al, Mn, Ce, Ni, Co and Cu) on the structural and catalytic properties of Nanocrystalline iron based catalysts for high temperature water gas shift reaction were investigated. The catalysts were prepared in active phase (Fe₃O₄) via a facile direct synthesis routs without any additive and characterized using X-ray diffraction (XRD), N₂ adsorption (BET), temperature-programmed reduction (TPR), transmission and scanning electron microscopies (TEM,SEM) techniques. The obtained results indicated that synergic effect of Mn and Ni promoters can lead to obtain a Cr-free catalyst with high activity. In addition, the effect of Ni content on the structural and catalytic properties of the Fe–Mn–Ni catalysts was investigated. It was found that Fe–Mn–Ni catalyst with Fe/Mn = 10 and Fe/Ni = 5 weight ratios showed the highest catalytic activity among the prepared catalysts and possessed a stable catalytic performance without any decrease during 10 h time on stream. Moreover, the effect of GHSV and steam/gas ratio on the catalytic performance of this catalyst was investigated.     

Morphological, optical and photocatalytic properties of TiO2–Fe2O3 multilayers

Morphological, optical and photocatalytic properties of TiO₂, Fe₂O₃ and TiO₂–Fe₂O₃ samples (formed by 1, 3 and 5 coatings) were studied. The layers were deposited on glass substrate by the sol–gel method. The catalytic activity of the samples was studied by the photodecomposition of methylene blue (MB) under visible light illumination. The FTIR results indicate that all samples present surface OH radicals that are bound either to the Ti or Fe atoms. This effect is better visualized at larger number of coatings in the TiO₂–Fe₂O₃/glass systems. Also, two mechanisms are observed during the photodecomposition of the MB.     

Influence of surfactants on Fe2O3 nanostructure photoanode

Fe₂O₃ nanostructures photoanodes were prepared via sol–gel spin-coating method onto fluorine-doped tin oxide glass substrates using six different surfactants: polyethylene glycol (PEG-300), Triton X-100, pluronic F127, cetyltrimethylammonium bromide (CTAB), octadecyltrimethylammonium bromide (OTAB) and tetradecyltrimethylammonium bromide (TTAB). The resulting films have thickness from 520 ± 10 to 980 ± 10 nm after calcinations at 450 °C in the air. A comparative study of photocatalytic activity of thin films was performed. The photo-generated samples were determined by measuring the currents and voltages under illumination of UV–vis light. The highest photocurrent density of 1.77 mA/cm² at 1 V/SCE, under illumination intensity of 100 mW cm⁻² from a solar simulator with a global AM 1.5 filter, were produced by TTAB treated sample. The optical properties, morphology, surface roughness and structure of the films were also characterized by UV–visible spectroscopy, SEM, AFM and XRD. The results are consistent with photocatalytic performance: TTAB treated sample has the highest grain size and optical absorption. The improved performance of this sample can be attributed to the crystallinity process of TTAB, which leads to the larger grain size and highest photocatalytic activity. The study demonstrates that photoelectrochemical performance of metal oxide can be improved by simply changing surfactant. The results highlighted the superior performance of cationic surfactants over non-ionic surfactants in preparing Fe₂O₃ photoanodes by sol–gel method. Moreover, the study showed that decreasing hydrocarbon tail of cationic surfactants can increase the crystallite size and improve photocatalytic activity.     

Silver/titania nanocomposite-modified photoelectrodes for photoelectrocatalytic methanol oxidation

Silver deposited titania (Ag/TiO₂) nanocomposite thin films were fabricated by the simple sonochemical deposition of Ag on preformed aerosol-assisted chemical vapor deposited TiO₂ thin films. The photelectrocatalytic performance of a newly fabricated Ag/TiO₂-modified photoelectrode was studied for methanol oxidation under simulated solar AM 1.5G irradiation (100 mW/cm²). The Ag/TiO₂-modified photoelectrode showed a photocurrent density of 1 mA/cm², which is four times that of an unmodified TiO₂ photoelectrode. The modification of Ag on the TiO₂ surface significantly enhanced the photoelectrocatalytic performance by improving the interfacial charge transfer processes, which minimized the charge recombination. Density functional theory (DFT) calculation studies revealed that methanol could be easily adsorbed onto the Ag surfaces of Ag/TiO₂ via a partial electron transfer from Ag to methanol. The newly fabricated Ag/TiO₂-modified photoelectrode could be a promising candidate for photoelectrochemical applications.     

Improved separation efficiency of photogenerated carriers for Fe2O3/SrTiO3 heterojunction semiconductor

To investigate the mechanisms of the improvement on separation efficiency of photogenerated carriers, a Fe₂O₃/SrTiO₃ heterojunction semiconductor with an improved separation efficiency was successfully prepared. The heterojunction semiconductor was characterized with X-ray diffraction (XRD), UV–vis absorption spectrum, scanning electron microscope (SEM) and surface photovoltage (SPV) spectroscopy. The energy band diagrams of Fe₂O₃ and SrTiO₃ were determined with X-ray photoelectron spectroscopy (XPS), based on which the conduction band offset (CBO) between Fe₂O₃ and SrTiO₃ was quantified to be 1.26 ± 0.03 eV. The recombination of photogenerated carriers was investigated with photoluminescence (PL) spectrum, which indicates that the formation of Fe₂O₃/SrTiO₃ decreases the recombination. Thus the improved separation efficiency is mainly due to the energy difference between the conduction band edges of Fe₂O₃ and SrTiO₃, and the decreased electron-hole recombination for Fe₂O₃/SrTiO₃.     

Study on photocurrent of bilayers photoanodes using different combination of WO3 and Fe2O3

Bilayer photoanodes were prepared onto glass substrates (FTO) in order to improve generated photocurrents using UV-vis light by water splitting process. A comparative study of photocatalytic was performed over the films surface using Fe₂O_3, WO₃ and mixture of bicomponents (Fe₂O₃:WO₃). Different types of films were prepared using Fe₂O_3, WO₃ and bicomponents (mixture) on FTO substrates. The films were grown by sol gel method with the PEG-300 as the structure-directing agent. The photo-generated of the samples were determined by measuring the currents and voltages under illumination of UV-vis light. The morphology, structure and related composition distribution of the films have been characterized by SEM, XRD and EDX respectively. Photocurrent measurements indicated surface roughness as the effective parameter in this study. The deposited surfaces by bicomponents or mixture are flat without any feature on the surface while the deposited surfaces by WO₃ appears rough surface as small round (egg-shaped particles) and cauliflower-like. The surface deposited by Fe₂O₃ show rough no as well as WO₃ surface. The deposited surfaces by WO₃ reveal the higher value of photocurrent measurement due to surface roughness. Indeed, the roughness can be effective in increasing contact surface area between film and electrolyte and diffuse reflection (light scattering effect). The solution (Fe₂O₃:WO₃) shows the low photocurrent value in compare to WO₃ and Fe₂O₃ hat it may be due to decomposition the compound at 450 ± 1 °C to iron-tungstate Fe₂(WO₄)₃.     

Blue-photon modification of nonstandard diode barrier in CuInSe2 solar cells

The current–voltage curves of many ZnO/CdS/CuInSe₂ solar cells display significant distortion when only red light illumination is employed. This distortion generally disappears or partially disappears for a period of time following illumination with blue light. Similarly, the dark diode curve shortly after illumination containing blue light is shifted significantly from the equilibrium dark curve. This effect is more common than generally realized and indicates a mechanism that is potentially detrimental to photovoltaic efficiency. A model is presented that is based on a low free-electron concentration and a high concentration of deep levels in the CdS window layer. This model is consistent with observed variations in current–voltage, capacitance, and laser scan data with illumination wavelength and history.     

Preparation of In2O3:F thin films grown by spray pyrolysis technique

Transparent conducting fluorine doped indium oxide (In₂O₃:F) thin films have been deposited on Corning 7059 glass substrates by the spray pyrolysis technique. The structural, electrical, and optical properties of these films were investigated as a function of substrate temperature. The X-ray diffraction pattern of the films deposited at lower substrate temperature (T_s=300 °C) showed no peaks of In₂O₃:F. In the useful range for deposition (i.e. 425–600 °C), the orientation of the films was predominantly [400]. For the 4500 Å thick In₂O₃:F deposited with an F content of 10-wt%, the minimum sheet resistance was 120 Ω and average transmission in the visible wavelength rang (400–700 nm) was 88%.     

Ultrathin hematite films deposited layer-by-layer on a TiO2 underlayer for efficient water splitting under visible light

Ultrathin hematite (α-Fe₂O₃) film deposited on a TiO₂ underlayer as a photoanode for photoelectrochemical water splitting was described. The TiO₂ underlayer was coated on conductive fluorine-doped tin oxide (FTO) glass by spin coating. The hematite films were formed layer-by-layer by repeating the separated two-phase hydrolysis-solvothermal reaction of iron(III) acetylacetonate and aqueous ammonia. A photocurrent density of 0.683 mA cm⁻² at +1.5 V vs. RHE (reversible hydrogen electrode) was obtained under visible light (>420 nm, 100 mW cm⁻²) illumination. The TiO₂ underlayer plays an important role in the formation of hematite film, acting as an intermediary to alleviate the dead layer effect and as a support of large surface areas to coat greater amounts of Fe₂O₃. The as-prepared photoanodes are notably stable and highly efficient for photoelectrochemical water splitting under visible light. This study provides a facile synthesis process for the controlled production of highly active ultrathin hematite film and a simple route for photocurrent enhancement using several photoanodes in tandem.     

Effects of Fe2O3 on pyrolysis characteristics of soybean protein and release of NOx precursors

The effects of ferric oxide (Fe₂O₃) on the pyrolysis characteristics of soybean protein and the release of precursors to nitrogen oxides (NOx) were studied using thermogravimetry and mass spectrometry. The results show that, as the content of Fe₂O₃ increases, there is no major difference between initial and peak temperatures of protein pyrolysis samples. Moreover, between the temperature range of 204 and 550°C where weight loss mainly occurs, total weight-loss rate decreases before increasing, with obvious weight loss occurring around the temperature of 650°C. Fe₂O₃ displays both inhibiting and promoting effects on the precipitation of nitrogen-containing gases such as ammonia (NH₃), hydrogen cyanide (HCN), isocyanic acid (HNCO), and acetonitrile (CH₃CN), with the inhibition effect prevailing over promotion effect on the whole.     

Characterization of electrolytic Co3O4 thin films as anodes for lithium-ion batteries

The electrolytic deposition of Co₃O₄ thin films on stainless steel was conducted in Co(NO₃)₂ aqueous solution for anodes in lithium-ion thin film batteries. Three major electrochemical reactions during the deposition were discussed. The coated specimens and the coating films carried out at −1.0 V (saturated KCl Ag/AgCl) were subjected to annealing treatments and further characterized by XRD, TGA/DTA, FE-SEM, Raman spectroscopy, cyclic voltammetry (CV) and discharge/charge cyclic tests. The as-coated film was β-Co(OH)₂, condensed into CoO and subsequently oxidized into nano-sized Co₃O₄ particles. The nano-sized Co₃O₄, CoO, Li₂O and Co particles revealed their own characteristics different from micro-sized ones, such as more interfacial effects on chemical bonding and crystallinity. The initial maximum capacity of Co₃O₄ coated specimen was 1930 mAh g⁻¹ which much more than its theoretical value 890 mAh g⁻¹, since the nano-sized particles offered more interfacial bondings for extra sites of Li⁺ insertion. However, a large ratio of them was trapped, resulting in a great part of irreversible capacity during the first charging. Still, it revealed a capacity 500 mAh g⁻¹ after 50 discharged-charged cycles.     

Mechanochemical synthesis of α-Fe2O3 nanoparticles and their application to all-solid-state lithium batteries

α-Fe₂O₃ fine particles have been prepared by a mechanochemical process and a solution process. α-Fe₂O₃ nanoparticles with aggregates composed of the several tens nm primary particles were produced by the mechanochemical process. The nanoparticles were applied to the electrode as an active material for all-solid-state lithium batteries and the electrochemical properties of the cell were investigated. Typical charge–discharge curves, as seen in the liquid type cell using the α-Fe₂O₃ nanoparticles as an electrode were observed in the all-solid-state cell. The first discharge capacity of the cell of about 780 mAh g⁻¹ was, however, smaller than the capacity of a cell using α-Fe₂O₃ particles prepared by the solution process, which were monodispersed particles of 250 nm without aggregates. In order to develop electrochemical performance of all-solid-state batteries, it is important to use the electrode particles without aggregation which lead to the formation of good solid–solid interface between active material and solid electrolyte particles.C     

Synthesis and electrochemical properties of olivine LiFePO4 prepared by a carbothermal reduction method

LiFePO₄/C composite cathode material was prepared by carbothermal reduction method, which uses NH₄H₂PO₄, Li₂CO₃ and cheap Fe₂O₃ as starting materials, acetylene black and glucose as carbon sources. The precursor of LiFePO₄/C was characterized by differential thermal analysis and thermogravimetry. X-ray diffraction (XRD), scanning electron microscopy (SEM) micrographs showed that the LiFePO₄/C is olivine-type phase, and the addition of the carbon reduced the LiFePO₄ grain size. The carbon is dispersed between the grains, ensuring a good electronic contact. The products sintered at 700 °C for 8 h with glucose as carbon source possessed excellent electrochemical performance. The synthesized LiFePO₄ composites showed a high electrochemical capacity of 159.3 mAh g⁻¹ at 0.1 C rate, and the capacity fading is only 2.2% after 30 cycles.     

Complexing agent effect on the stoichiometric ratio of the electrochemically prepared CuInSe2 thin films

The electrodeposition of CuInSe₂ is investigated to improve the stoichiometric properties of CuInSe₂ layers on indium tin oxide (ITO)-coated glass substrates and to develop one-step electrodeposition method for solar cell applications. XPS was utilized for the characterization of the surface properties of CuInSe₂ layers. The influence of the complexing agent, e.g. benzotriazole, bulk concentration of Cu and Se and deposition potentials on the stoichiometric properties, are discussed.     

Photoelectrochemical study on charge transfer properties of nanostructured Fe2O3 modified by g-C3N4

Novel photocatalysts, which consist of two visible light responsive semiconductors including graphite-like carbon nitride (g-C₃N₄) and Fe₂O₃, were successfully synthesized via electrodeposition followed by chemical vapor deposition. The morphology of the g-C₃N₄/Fe₂O₃ can be tuned from regular nanosheets to porous cross-linked nanostructures. Remarkably, the optimum activity of the g-C₃N₄/Fe₂O₃ is almost 70 times higher than that of individual Fe₂O₃ for photoelectrochemical water splitting. The enhancement of photoelectrochemical activity could be assigned to the morphology change of the photocatalysts and the effective separation and transfer of photogenerated electrons and holes originated from the intimately contacted interfaces. The g-C₃N₄/Fe₂O₃ composites could be developed as high performance photocatalysts for water splitting and other optoelectric devices.     

Solar cells with Cu(In1−xGax)S2 thin films prepared by sulfurization

By rapid thermal processing of Cu/In/GaS precursors, good-quality CuIn_1–xGa_xS₂ films are synthesized. By suppressing the formation of In-rich hillocks, we could obtain homogeneous CuIn_1–xGa_xS₂ surfaces. A conversion efficiency of 12% has been achieved using a relatively low (1.2) Cu/In ratio.     

Effect of support composition and metal loading on Au catalyst activity in steam reforming of methanol

Gold (Au) supported on CeO₂–Fe₂O₃ catalysts prepared by the deposition-coprecipitation technique were investigated for steam reforming of methanol (SRM). The 3 wt% Au/CeO₂–Fe₂O₃ sample calcined at 400 °C achieved 100% methanol conversion and 74% hydrogen yield due to a strong Ce–Fe interaction in the active solid solution phase, Ce_xFe_1−xO₂. The sintering of Au particles was observed when the highest metal content of 5 wt% was registered, which worsened the SRM activity. According to the TPR and TPO analysis, it was found that the transformation of the α-Fe₂O₃ structure in the mixed oxides and the coke deposition were the main factors for the rapid deactivation of the catalyst.     

CVD of CuGaSe2 for thin film solar cells with various transport agents

Chemical vapor deposition (CVD) in an open tube system was employed to deposit single-phase CuGaSe₂ thin films on plain and Mo-coated glass substrates. The use of HCl and ternary CuGaSe₂ source material resulted in non-stoichiometric volatilization of the source material. The use of binary source materials – Cu₂Se and Ga₂Se₃ – in combination with I₂ and HCl as the respective transport agents yielded single-phase CuGaSe₂ thin films while the source materials were volatilized stoichiometrically. Mo/CuGaSe₂/CdS/ZnO devices were fabricated from these samples exhibiting an open-circuit voltages up to V_oc=853 mV.     

Electrochemical deposition of porous Co3O4 nanostructured thin film for lithium-ion battery

Porous Co₃O₄ nanostructured thin films are electrodeposited by controlling the concentration of Co(NO₃)₂ aqueous solution on nickel sheets, and then sintered at 300 °C for 3 h. The as-prepared thin films are characterized by thermogravimetric analysis (TGA), X-ray diffraction (XRD), and scanning electron microscopy (SEM). The electrochemical measurements show that the highly porous Co₃O₄ thin film with the highest electrochemically active specific surface area (68.64 m² g⁻¹) yields the best electrochemical performance compared with another, less-porous film and with a non-porous film. The highest specific capacity (513 mAh g⁻¹ after 50 cycles) is obtained from the thinnest film with Co₃O₄ loaded at rate of 0.05 mg cm⁻². The present research demonstrates that electrode morphology is one of the crucial factors that affect the electrochemical properties of electrodes.     

Magnetic field effects on selective catalytic reduction of NO by NH3 over Fe2O3 catalyst in a magnetically fluidized bed

Selective catalytic reduction (SCR) of NO from simulated flue gas by ammonia with Fe₂O₃ particles as the catalyst was performed using a magnetically fluidized bed (MFB). X-ray diffraction (XRD) spectroscopy and Brunauer–Emmett–Teller (BET) method were used to analyze Fe₂O₃ catalyst. Important effects of magnetic fields were observed in the SCR of NO by ammonia over Fe₂O₃ catalyst. The apparent activation energies of SCR were reduced by external magnetic fields, and the SCR activity of Fe₂O₃ catalyst was improved with the magnetic fields at low temperatures. Thus the scope of temperature with high efficiency of NO removal was extended from 493–523 K to 453–523 K by magnetic fields. Magnetic fields of 0.01–0.015 T were suggested for NO removal on Fe₂O₃ catalyst with MFB. The results suggested that the magnetoadsorption of NO onto Fe₂O₃ surface together with NH₂ and NO free radicals effects induced by the external magnetic fields both acted to improve the rate of SCR of NO on Fe₂O₃ catalyst. On the other hand, magnetic field effects were also attributed to improved gas–solid contact in MFB.