基于超临界CO2循环的地热与太阳能混合系统研究

超临界CO₂循环可以耦合较低温度的地热和较高温度的太阳能热组成混合热源发电系统。相比能量分析方法,火用分析方法更便于分析混合系统对提高能量利用率的作用,以及识别造成可用能损失的设备和过程。115℃地热和200℃地热分别与采用槽式聚光集热技术的太阳能热组成混合热源,构成简单回热超临界CO₂循环。分析结果表明：混合系统的火用效率比单纯太阳能热的循环系统提高了5% ~ 10%;太阳能聚光集热器的?损失最大,占80%以上,其次是除预冷器以外的各类换热器以及透平;相比之下,压缩机和预冷器的火用损失较小。减少?损失的关键是提高太阳能聚光集热器和换热器的性能,包括提高集热管运行温度,以及提高换热器效能。     

Integrated solar combined cycle system with steam methane reforming: Thermodynamic analysis

The present paper considers an integrated solar combined cycle system (ISCCS) with an utilization of solar energy for steam methane reforming. The overall efficiency was compared with the efficiency of an integrated solar combined cycle system with the utilization of solar energy for steam generation for a steam turbine cycle. Utilization of solar energy for steam methane reforming gives the increase in an overall efficiency up to 3.5%. If water that used for steam methane reforming will be condensed from the exhaust gases, the overall efficiency of ISCCS with steam methane reforming will increase up to 6.2% and 8.9% for β = 1.0 and β = 2.0, respectively, in comparison with ISCCS where solar energy is utilized for generation of steam in steam turbine cycle. The Sankey diagrams were compiled based on the energy balance. Utilization of solar energy for steam methane reforming increases the share of power of a gas turbine cycle: two-thirds are in a gas turbine cycle, and one-third is in a steam turbine cycle. In parallel, if solar energy is used for steam generation for a steam turbine cycle, than the shares of power from a gas and steam turbine are almost equal.     

Performance evaluation of a combined power generation system integrated with thermochemical exhaust heat recuperation based on steam methane reforming

The present paper applies the thermodynamic analysis with the determining the efficiency of a combined cycle power plant with a chemically recuperated gas turbine. Thermochemical recuperation of exhaust heat after a gas turbine is realized via the steam methane reforming process. The main concept of combined cycle power plant (CCPP) with chemically recuperated gas turbine (CRGT) is based on the use of exhaust heat for endothermic reforming of the original hydrocarbon fuel in a reformer and for steam generation for a steam cycle. To understand the effect of operating variables such as temperature, pressure, and steam-to-methane ratio on the overall efficiency, the energy and mass balances were compiled. The energy flows were represented by a Sankey diagram. The results of the thermodynamic analysis show that efficiency of CCPP with CRGT is significantly higher (4–7%) than efficiency of CCPP with a conventional gas turbine without TCR. Maximum efficiency of CCPP with CRGT of 0.6412 is observed at inlet temperature of working gas of 1600 °C, pressure of 23 bar for a steam-to-methane ratio of 3.0. In the temperature of inlet working gas below 1200 °C the increase in the efficiency of CCPP with TCR is less than 2%.     

Thermal design of methane steam reformer with low-temperature non-reactive heat source for high efficiency engine-hybrid stationary fuel cell system

In hybrid fuel cell systems, the fuel-lean anode-off gas is very useful to improve the system efficiency via additional power generation or utilization of thermal energy for heating up of auxiliary devices. In this study, the thermal energy of the hybrid systems is firstly utilized in homogeneous charge combustion engine for additional power and is then supplied to heat up the external reformer. Different from other hybrid fuel cell systems, it is very difficult to utilize heat energy of exhausted gas from engine due to its low temperature characteristics. This study is concentrated on the computation analysis of external methane steam reformers with engine out exhausted gases. Computational model is validated with experiment and parametric study is conducted. Results show that the temperature uniformity of the longitudinal and radial directions is crucial for the methane conversion efficiency. Additionally, the methane conversion rate also depends on the performance of tube-side heat transfer. When the total methane flow is fixed, the methane conversion rate shows trade-off with increasing steam-to-carbon ratio (SCR). Finally, the sensitivity study shows that heat transfer area and reactor length are dominant parameters for steam reforming with engine out exhausted gases.     

太阳能光伏光热一体化系统运行实验研究

太阳能光伏光热一体化系统（hybrid photovoltaic-thermal solar system—PVT系统）作为一种利用太阳能同时获得电收益和热收益的新型能源利用方式,近年来受到学者的广泛关注。本文搭建了PVT系统电、热性能综合实验台,通过全天实验,分别研究和分析了系统的温度特性与相对电效率的关系。结果袁明,在日照条件较好,系统循环水温较低的情况下,PVT系统的电效率与普通光伏电池相比可以提高约7％。同时,文章还分析了PVT系统内水的温度一天内的变化情况,提出了在午后太阳辐射强度逐渐减弱,环境温度逐渐升高时如何保持PVT系统较高电效率的方法。     

Ethanol steam reforming heated up by molten salt CSP: Reactor assessment

In this paper hydrogen production via reforming of ethanol has been studied in a novel hybrid plant consisting in a ethanol reformer and a concentrating solar power (CSP) plant using molten salt as heat carrier fluid. The heat needed for the reforming of ethanol has been supplied to the system by molten salts heated up by solar energy. The molten salt stream temperature drop for supplying hydrogen production process heat duty is less than 20 K, making the molten salt stream still suitable for steam and electricity production in a co-generative plant (clean hydrogen and electricity).     

Thermodynamic analysis of the CO2‐based Rankine cycle powered by solar energy

Using carbon dioxide as working fluid receives increasing interest since the Kyoto Protocol. In this paper, thermodynamic analysis was conducted for proposed CO₂‐based Rankine cycle powered by solar energy. It can be used to provide power output, refrigeration and hot water. Carbon dioxide is used as working fluid with supercritical state in solar collector. Theoretical analysis was carried out to investigate performances of the CO₂‐based Rankine cycle. The interest was focused on comparison of the performance with that of solar cell and those when using other fluids as working fluids. In addition, the performance and characteristics of the thermodynamic cycle are studied for different seasons. The obtained results show that using CO₂ as working fluid in the Rankine cycle owns maximal thermal efficiency when the working temperature is lower than 250.0°C. The power generation efficiency is about 8%, which is comparable with that of solar cells. But in addition to power generation, the CO₂‐based solar utilization system can also supply thermal energy. Copyright © 2007 John Wiley & Sons, Ltd.     

A numerical study of geometric effects on the performance characteristics of shell-and-tube methanol reformers

Methanol reforming is a key method of producing hydrogen, an eco-friendly energy source. A feasible validation has been performed using previous experimental data. Present numerical model, validated using previously published experimental data, facilitates a factor-by-factor study of methanol reforming performance characteristics. In particular, the effects of inlet temperature of reformed gas and heat source gas, gas hourly space velocity (GHSV), reformer length, and reformer diameter are numerically analyzed. The effect of each parameter on reforming performance was presented by analyzing the average temperature of the reformed gas for each location inside the reformer. In addition, the inlet temperature of the heat source gas was more dominant in reforming performance than that of the reformed gas through sensitivity analysis. Finally, the performance was explained in terms of residence time, and the relationship between CO selectivity and residence time was presented.     

Four different configurations of a 5 kW class shell-and-tube methane steam reformer with a low-temperature heat source

The methane steam reforming reaction is an extremely high endothermic reaction that needs a high temperature heat source. Various fuel cell hybrid systems have been developed to improve the thermal efficiency of the entire system. This paper presents a low temperature steam reformer for those hybrid systems to maximize the utilization of energy from a low temperature waste heat source. In this study, the steam reformer has a shell and tube configuration that is divided into the following zones: the inlet heat exchanging zone, the reforming zone and the exit heat exchanging zone. Four different configurations for methane steam reformers are developed to examine the effect of heat transfer on the methane conversion performance of the low temperature steam reformer. The experimental results show that the overall heat transfer area is a critical parameter in achieving a high methane conversion rate. When the heat transfer area increases about 30%, the results showed elevated dry mole fractions of hydrogen about 3% with about 30 °C rise of reformer outlet temperature.     

Performance assessment of a direct steam solar power plant with hydrogen energy storage: An exergoeconomic study

Power generation and its storage using solar energy and hydrogen energy systems is a promising approach to overcome serious challenges associated with fossil fuel-based power plants. In this study, an exergoeconomic model is developed to analyze a direct steam solar tower-hydrogen gas turbine power plant under different operating conditions. An on-grid solar power plant integrated with a hydrogen storage system composed of an electrolyser, hydrogen gas turbine and fuel cell is considered. When solar energy is not available, electrical power is generated by the gas turbine and the fuel cell utilizing the hydrogen produced by the electrolyser. The effects of different working parameters on the cycle performance during charging and discharging processes are investigated using thermodynamic analysis. The results indicate that increasing the solar irradiation by 36%, leads to 13% increase in the exergy efficiency of the cycle. Moreover, the mass flow rate of the heat transfer fluid in solar system has a considerable effect on the exergy cost of output power. Solar tower has the highest exergy destruction and capital investment cost. The highest exergoeconomic factor for the integrated cycle is 60.94%. The steam turbine and PEM electrolyser have the highest share of exergoeconomic factor i.e., 80.4% and 50%, respectively.     

A transient study of double-jacketed membrane reactor via methanol steam reforming

A non-isothermal unsteady-state model was established to simulate methanol steam reforming using a double-jacketed Pd membrane reactor. At steady state, a self-sustained membrane reactor was achieved by the oxidation of residual methanol and hydrogen from reformer for endothermic steam reforming. The molar fractions of species and reformer temperature were analyzed under co-current operation between oxidation and reformer sides. The start-up of reformer was simulated under two conditions: (1) The catalyst temperature was lower than the influent temperature and (2) The catalyst temperature was higher than influent temperature. Condition 1 yielded higher methanol conversion and reformer temperature than condition 2 at steady state. Moreover, the instability of species can be minimized on condition 1 during start-up. The fluctuation of membrane reactor at steady state was also studied. Two strategies were compared to analyze the reformer response when temporary extra hydrogen was required. The results showed that increasing inlet methanol outperformed increasing reformer temperature.     

Effects of PEMFC operating parameters on the performance of an integrated ethanol processor

In this paper the performance of a complete fuel cell system processing ethanol fuel has been analyzed as a function of the main fuel cell operating parameters. The fuel processor is based on the steam reforming process, followed by high- and low-temperature shift reactors, and carbon monoxide preferential oxidation reactor, which are coupled to a polymeric fuel cell (PEMFC). The goal was to analyze and improve the fuel cell system performance by simulation techniques. PEMFC operation has been analyzed using an available parametric model, which was implemented within HYSYS environment software. Pinch Analysis concepts were used to investigate the process energy integration and determine the maximum efficiency minimizing ethanol consumption. The system performance was analyzed for the SR-12 Modular PEM Generator, the Ballard Mark V fuel cell and the BCS 500 W stack. The net system efficiency is dependent on the required power demand. Efficiency values higher than 50% at low loads and less than 30% at high power demands are computed. In addition, the effect of fuel cell temperature, pressure and hydrogen utilization was analyzed. The trade-off between the reformer yield and the fuel cell performance defines the optimal operation pressure. The cell temperature determines operating zones where the water, involved in the reforming reactions, can be produced or demanded.     

Mini CHP based on the electrochemical generator and impeded fluidized bed reactor for methane steam reforming

The paper presents a configuration of mini CHP with the methane reformer and planar solid oxide fuel cell (SOFC) stacks. This mini CHP may produce electricity and superheated steam as well as preheat air and methane for the reformer along with cathode air used in the SOFC stack as an oxidant. Moreover, the mathematical model for this power plant has been created. The thermochemical reactor with impeded fluidized bed for autothermal steam reforming of methane (reformer) considered as the basis for the synthesis gas (syngas) production to fuel SOFC stacks has been studied experimentally as well. A fraction of conversion products has been oxidized by the air fed to the upper region of the impeded fluidized bed in order to carry out the endothermic methane steam reforming in a 1:3 ratio as well as to preheat products of these reactions. Studies have shown that syngas containing 55% of hydrogen could be produced by this reactor. Basic dimensions of the reactor as well as flow rates of air, water and methane for the conversion of methane have been adjusted through mathematical modelling.The paper provides heat balances for the reformer, SOFC stack and waste heat boiler (WHB) intended for generating superheated water steam along with preheating air and methane for the reformer as well as the preheated cathode air. The balances have formed the basis for calculating the following values: the useful product fraction in the reformer; fraction of hydrogen oxidized at SOFC anode; gross electric efficiency; anode temperature; exothermic effect of syngas hydrogen oxidation by air oxygen; excess entropy along with the Gibbs free energy change at standard conditions; electromotive force (EMF) of the fuel cell; specific flow rate of the equivalent fuel for producing electric and heat energy. Calculations have shown that the temperature of hydrogen oxidation products at SOFC anode is 850 °C; gross electric efficiency is 61.0%; EMF of one fuel cell is 0.985 V; fraction of hydrogen oxidized at SOFC anode is 64.6%; specific flow rate of the equivalent fuel for producing electric energy is 0.16 kg of eq.f./(kW·h) while that for heat generation amounts to 44.7 kg of eq.f./(GJ). All specific parameters are in agreement with the results of other studies.     

Syngas production from oxidative methane reforming and CO cleaning with water gas shift reaction

Fuel cell based heat and power cogeneration is considered to be well qualified for a distributed energy system for residential and small business applications. A fuel processing unit including an oxidative steam methane reformer, a high temperature shift reactor and a low temperature shift reactor is under development in South China University of Technology. Performance of the unit is experimentally investigated in a bench-scale experimental setup. Processor performance under typical operating conditions is tested. The influence of reaction temperature, methane space velocity in the oxidative steam methane reformer, and air to carbon molar ratio on unit performances is experimentally studied. It is found that under the typical operating conditions, the total energy efficiency reaches 88.3%. The efficiency can further be improved by utilizing the sensible heat of the reformate gas. The current study has been focused on the chemical performances such as methane conversion of the reformer and CO concentration in the synthesis gas downstream water gas shift reactors. Heat integration of the unit will be further implemented in future to improve energy efficiency.     

Catalytic exhaust gas fuel reforming for diesel engines—effects of water addition on hydrogen production and fuel conversion efficiency

Previous work in our laboratory has shown that the exhaust gas assisted fuel reforming process has the potential to provide a solution to the diesel engine exhaust emission problems. When simulated reformer product gas rich in hydrogen is fed to the engine, a reduction of both NO_x and smoke emissions can be achieved. In this paper, the optimisation of the reforming process by water addition in the reactor is presented. Using a prototype catalyst at 290°C reactor inlet temperature, up to 15% more hydrogen in the reformer product was obtained compared to operation without water. The process has been found to be mainly a combination of the fuel oxidation, steam reforming and water gas shift reactions. The reforming process efficiency has been shown to improve considerably with water addition up to a certain level after which the adverse effects of the exothermic water gas shift reaction become significant.     

Measurement and analysis of carbon formation during diesel reforming for solid oxide fuel cells

Experiments and equilibrium analysis were conducted to study carbon formation during diesel reforming for a solid oxide fuel cell-based auxiliary power unit (APU) application. A photo-acoustic instrument provided direct measurements of solid carbon concentration in the reformer effluent stream, which could be correlated to reformate gas composition (as determined via mass spectrometer) and reformer temperature. These measurements were complimented by equilibrium calculations based upon minimization of total Gibbs free energy. It was determined that oxygen-to-carbon ratio (O/C), fuel utilization fraction and anode recycle fraction all influence the degree of carbon formation, and that once significant carbon concentration is measured, the reformer performance begins to show marked degradation. At a fixed operating point, lowering the reformer temperature produced by far the largest change in effluent carbon concentration. Systematic variation in O/C, fuel utilization and anode recycle revealed the interdependence among reformer temperature, effluent gas composition and carbon concentration, with a strong correlation between carbon and ethylene concentrations observed for [C₂H₄] > 0.8%. After each experiment, baseline reformer performance could be recovered by operation under methane partial oxidation (POx) conditions, indicating that reformer degradation results at least in part from carbon deposition on the reformer catalyst.     

盐梯度太阳池Kalina循环发电系统性能研究

Kalina循环发电系统是一种典型的低温热源发电系统,具有广阔的应用前景。盐梯度太阳池能够实现连续聚热和跨季节蓄热,可广泛应用于光热发电系统和光热供热系统。文章提出了一种以太阳池储热量为热源的盐梯度太阳池Kalina循环发电系统,并利用Aspen Hysys软件对该系统进行建模。而后根据模拟结果,研究了提热温度、运行压力和氨水浓度对该系统各项性能的影响。此外,还分析了典型工况下,该系统的热力性能。分析结果表明:随着提热温度逐渐升高,盐梯度太阳池Kalina循环发电系统的发电功率、热效率和效率均逐渐增加;随着运行压力逐渐升高,该系统的热效率和效率逐渐升高,并且存在最佳的运行压力1.75 MPa,使得该系统获得最大发电功率;随着氨水浓度逐渐增大,该系统的发电功率也会逐渐增大,但热效率和效率却逐渐降低;当氨水浓度为85%、运行压力为1.75 MPa、提热温度为90℃时,该系统的热效率和效率分别为7.93%,57.59%。     

基于太阳能热驱动甲烷重整制氢的燃料电池发电系统性能研究

该文采用Aspen Plus软件建立膜反应器重整制氢及燃料电池模型,根据拉萨某日太阳能直接辐射强度（DNI）变化计算太阳能可供使用的能量,作为外热源输入重整系统,并分析反应温度、水碳比（S/C）及DNI对该系统各性能指标的影响,性能指标包括甲烷转化率、H₂收率、电池功率及电压、太阳能转换为氢能的效率。结果表明：反应温度为500 ℃,S/C为2.5时有利于太阳能甲烷湿重整反应;系统日性能结果显示在某日10:00—20:00时,电池输出功率120 kW,太阳能-化学能转化效率0.368,系统发电效率0.225。     

Thermodynamic analysis of a transcritical CO2 power cycle driven by solar energy with liquified natural gas as its heat sink

This paper proposes a transcritical CO₂ power cycle driven by solar energy while utilizing the cold heat rejection to an liquified natural gas (LNG) evaporation system. In order to ensure a continuous and stable operation for the system, a thermal storage system is introduced to store the collected solar energy and to provide stable power output when solar radiation is insufficient. A mathematical model is developed to simulate the solar-driven transcritical CO₂ power cycle under steady-state conditions, and a modified system efficiency is defined to better evaluate the cycle performance over a period of time. The thermodynamic analysis focuses on the effects of some key parameters, including the turbine inlet pressure, the turbine inlet temperature and the condensation temperature, on the system performance. Results indicate that the net power output mainly depends on the solar radiation over a day, yet the system is still capable of generating electricity long after sunset by virtue of the thermal storage tank. An optimum turbine inlet pressure exists under given conditions where the net power output and the system efficiency both reach maximum values. The net power output and the system efficiency are less sensitive to the change in the turbine inlet temperature, but the condensation temperature exerts a significant influence on the system performance. The surface area of heat exchangers increases with the rise in the turbine inlet temperature, while changes in the turbine inlet pressure have no significant impact on the heat exchanging area under the given conditions.     

Exergetic utilization of solar energy for feed water preheating in a conventional thermal power plant

This communication is based on exergy concept for the utilization of solar thermal energy in a Rankine cycle‐based fuel‐fired thermal power plant (FFTPP). It has been shown that solar thermal energy as an aided source for feed water preheating helps to reduce the exergy loss in feed water heater (FWH) of Rankine cycle and develops more work than that could have been produced in a solar thermal power plant (STPP). It has been found that this enhancement in work increases for low‐pressure FWHs. For further illustration, a case study has been carried out of a typical 50 kW STPP and a 220 MW FFTPP. The effect of utilizing the same input solar thermal energy of typical STPP, if used as an aided source in a 220 MW FFTPP for feed water preheating is investigated. The work output of STPP is 59.312 kW, while the extra work output of FFTPP by using solar thermal energy of STPP is 90.27 kW. It has been found that the efficiency of work conversion of aided solar thermal energy in FFTPP is higher than the efficiency of work conversion in STPP. Copyright © 2009 John Wiley & Sons, Ltd.