Microstructure and rheological behavior of hypereutectic semi-solid Al–Si alloy under low shear rates compression test

Permanent mold cast cylindrical samples were reprocessed to form semi-solid billets of A390 Al–Si alloy, employing a thixocasting method. The billets were reheated to predetermined mushy zone temperatures and held isothermally during parallel plate compression tests. The deformation behavior of the billets was measured at different applied pressures, and fraction solids determined by the preheating temperature. The calculated viscosities confirmed pseudoplastic behavior of the semi-solid alloys and were correlated to the solid fraction and shear rate to illustrate the effect of metallurgical and process parameters on the viscosity and the consequent rheological behavior of these alloys.     

Deformation behavior and microstructural evolution during the semi-solid compression of Al–4Cu–Mg alloy

The effects of the process parameters, including deformation temperature and strain rate, on the deformation behavior and microstructure of an Al–4Cu–Mg alloy, have been investigated through isothermal compression. Experiments were conducted at deformation temperatures of 540 °C, 560 °C, and 580 °C, strain rates of 1 s⁻¹, 1×10⁻¹ s⁻¹, 1×10⁻² s⁻¹, and 1×10⁻³ s⁻¹, and height reductions of 20%, 40%, and 60%. The experimental results show that deformation temperature and strain rate have significant effect on the peak flow stress. The flow stress decreases with an increase of deformation temperature and/or a decrease of the strain rate. Above a critical value of the deformation temperature, the flow stress quickly reaches a steady value. Experimental materials A and B have equiaxed and irregular grains, respectively, prior to deformation. The microstructures vary with the process parameters in the semi-solid state. For material B, the irregular grains transform to equiaxed grains in the process of semi-solid deformation, which improves the deformation behavior.     

Microstructure and mechanical properties of extruded Al–Si alloy (A356) in the semi-solid state

Smooth round bars were produced from conventional non-modified cast alloy, A356, by semi-solid extrusion after isothermal holding in mushy zone. Extrusion process was carried out in an apparatus, designed and prepared for this purpose at a ram speed, 2.5 mm/s. Three forming temperatures: 560, 570 and 580 °C; three isothermal holding times: 5, 30 and 60 min; and two extrusion reduction ratios: 5.3 and 17.8 were the used parameters. A clear modification of eutectic phase and an improvement in hardness and tensile properties were found compared with those of conventional casting. The tensile test specimens fracture surfaces were examined using SEM. Furthermore, wear resistance, fatigue strength and impact energy were also, improved significantly.     

Effect of cryorolling on microstructure of Al–Mg–Si alloy

The microstructural evolution of a precipitation hardenable Al–Mg–Si alloy subjected to cryorolling at different stain levels is reported in this present work. The cryorolled Al 6063 alloy were characterized by using SEM/EBSD and transmission electron microscopy (TEM), respectively. The phase identification of the cryorolled Al alloy samples were carried out by XRD. Differential scanning calorimetry (DSC) was used to study the influence of strain on precipitate evolution in Al–Mg–Si alloy. The formation of ultrafine grains and very fine sub grains in the grain interior, with a strain value of 3.6, is observed in the Al–Mg–Si alloy.     

Microscopic observation of cold-deformed Al–4Cu–Mg alloy samples after semi-solid heat treatments

Wrought aluminum alloys can be effectively fabricated by a strain-induced, melt-activated (SIMA) process. The SIMA method involves plastic deformation of an alloy to some critical reduction point and a semi-solid heat treatment in the solid–liquid temperature range. The semi-solid heat treatment is a key process to control the semisolid microstructures. In this paper, the microscopic morphology of a cold-deformed SIMA treated Al–4Cu–Mg alloy has been investigated, and the effects of microstructural evolution, precipitation behavior and dislocation morphology on the mechanical properties are discussed. The experimental results show that the number of CuAl₂ (θ phase) precipitates and the dislocation density of Al–4Cu–Mg alloy decreased gradually by the semi-solid heat treatment. Moreover, unique dislocation morphologies including helical dislocations and dislocation loops appeared and evolved to reduce the stored energy. With an increase of the holding time in the semi-solid heat treatment, the ultimate strength and yield strength decreased. The reduction of these mechanical properties of the SIMA treated Al–4Cu–Mg alloy is mainly due to the decrease of refinement strengthening, solution strengthening, and dislocation strengthening in the semi-solid heat treatment.     

Significant improvement of semi-solid microstructure and mechanical properties of A356 alloy by ARB process

Accumulative roll bonding (ARB) process was used in this study as an effective method for manufacturing high-strength, finely-dispersed and highly-uniform A356 alloy. It was found that when the number of ARB cycles was increased, the uniformity of silicon particles in the aluminum matrix improved, the particles became finer and spheroider and therefore, the tensile strength (TS) and ductility of the samples improved. The microstructure of the manufactured A356 alloy after five ARB cycles indicated a totally modified structure such that it's TS and elongation values reached 269 MPa and 5.3% which were 2.6 and 2.5 times greater than those of the as-cast material, respectively. Also, the hardness value increased from 55.4 (for as-cast sample) to 100.2 HV (after the fifth cycle of ARB), and registered 81% increase.     

Fragility of superheated melts in Al–RE (Ce, Nd, Pr) alloy system

The fragility of superheated melt M, characterized by the temperature dependence of the viscosity scaled by the viscosity at the liquidus temperature, has been proposed by Bian et al. recently. In this work, the values of M of Al–RE(Ce, Nd, Pr) melts were calculated based on the viscosities measured in the range of less than 250 K above their liquidus temperatures. It was found that M has a good negative correlation with the glass-forming ability (GFA) in Al–RE binary alloy system. Although the previous study found that M could reflect the GFA in Al–Co–Ce alloy system, there is no good relationship between M and GFA in the alloy system including Al–RE and Al–Co–Ce alloys simultaneously. The relationship between fragility of superheated melts and glass-forming behavior in different Al-based alloy systems was elaborated.     

Combined grain refining and modification of conventional and rheo-cast A356 Al–Si alloy

This paper describes a comprehensive study on the combined addition of Ti–B grain refiner and Sr modifier elements to A356 Al–Si alloy. Using different qualitative and quantitative techniques in conventional and semi-solid metal castings, it is shown that, while the refiner and modifier elements affect respectively the nucleation and eutectic reactions, the combined addition not only replicates both individual element effects but also gives the added bonus of better globularity in the semi-solid metal process. A new innovative concept is introduced for fluidity measurement by using the magnitude of remaining liquid in the form of drainage, which is increased by combined treatment.     

Microstructure and grain refining performance of Al–5Ti–1B master alloy prepared under high-intensity ultrasound

The microstructure and grain refining performance of an Al–5Ti–1B master alloy prepared under high-intensity ultrasound were investigated. With applying continuous high-intensity ultrasound vibrations in the reaction, the Al–5Ti–1B master alloy is successfully manufactured in 4 min. Compared with conventional Al–5Ti–1B master alloys, the mean size and the size spread of TiB₂ particles in the prepared master alloy are evidently decreased. The narrower particle size spread significantly improves the grain refining performance of the master alloy, which proves the calculation predictions by Greer. Consequently, the limiting grain size of commercial purity aluminium refined by the new master alloy can reach 45 μm.     

Microstructure and mechanical properties of nanocrystalline high strength Al–Mg–Si (AA6061) alloy by high energy ball milling and spark plasma sintering

In the present paper, the microstructure and mechanical properties of nanostructured Al–Mg–Si based AA6061 alloy obtained by high energy ball milling and spark plasma sintering were reported. Gas atomized microcrystalline powder of AA6061 alloy was ball milled under wet condition at room temperature to obtain nanocrystalline powder with grain size of 30 nm. The nanocrystalline powder was consolidated to fully dense compacts by spark plasma sintering (SPS) at 500 °C. The grain size after SPS consolidation was found to be 85 nm. The resultant SPS compacts exhibited microhardness of 190–200 HV_100 g, compressive strength of 800 MPa and strain to fracture of 15%.     

Synthesis of ultra high strength Al–Mg–Si alloy sheets by differential speed rolling

The ultrafine-grained Al–Mg–Si alloy sheets, which were fabricated by severe plastic deformation (SPD) using a high-speed-ratio differential speed rolling (HRDSR) and subsequent low temperature aging, exhibited an ultra high strength (yield stress: 455 MPa, ultimate tensile strength: 489 MPa). The strengthening effect was impressive compared with the results obtained by using other SPD techniques. The achievement could be attributed to formation of very fine grains due to significantly increased dislocation density in solute supersaturated matrix, high Hall-Petch constant and particle strengthening gained by formation nano-scale precipitates during the low temperature aging after the HRDSR process.     

Effect of equal-channel angular extrusion on mechanical and wear properties of eutectic Al–12Si alloy

Mechanical and wear properties of severely deformed Al–12Si alloy by equal-channel angular extrusion/pressing (ECAE/P) were investigated. Multi-pass ECAE processing of the as-cast alloy substantially increased both its strength and ductility. The increase in the tensile and yield strength values after six ECAE passes were about 48% and 87%, respectively. The sample after six ECAE passes exhibited 10% elongation before rupture, which was about five times higher than that of the as-cast one. The improvement in both strength and ductility was mainly attributed to the changes of the shape, size and distribution of the eutectic silicon particles along with the breakage and refined of the large α-Al grains during multi-pass ECAE processing. However, the wear test results surprisingly showed that the ECAE process decreased the wear resistance of the alloy, although there was improvement in strength and ductility values. This was mainly attributed to the tribochemical reaction leading to oxidative wear with the abrasive effect in Al–Si alloys during sliding. The oxide layer played a dominant role in determining the wear resistance of the sample in both as-cast and ECAE-processed states, and it masked the effect of strengthening of alloy structure on the wear resistance.     

Fatigue crack growth behavior of X2095 Al–Li alloy

Microstructures and micro-textures of X2095 Al–Li alloy in as-received/superplastic state were characterized by means of SEM/BDS, X-ray diffraction and orientation imaging microscopy (OIM). It was observed that the microstructure of the alloy was typical of a particulate-reinforced composite material, consisting of aluminum matrix and homogeneously distributed T_B(Al₇Cu₄Li) particles with a volume fraction of about 10%. Brass-type texture was the dominant texture component. Both constant amplitude and near-threshold fatigue crack growth rates of the alloy in the L–T and T–L orientations were determined at different stress ratios. Particular attention was paid to the role of the T_B phase in the fatigue crack growth. When a fatigue crack approached a T_B particle, the crack basically meandered to avoid the particle. The T_B particles thus provided a strong resistance to the propagation of fatigue crack by promoting crack deflection and the related crack closure effects. The fatigue crack propagation behavior has been explained by the microstructural features, micro-textures, cracking characteristics and crack closure effects.     

Effect of texture on high temperature deformation behavior at high strain rates in a Mg–3Al–1Zn alloy

A microstructure optimization design method of the forging process is proposed. The optimization goal is a small grain size and a homogeneous grain distribution of the forgings. The optimization object is the preforming die shape. The microstructure optimization code is developed using the micro-genetic algorithm and the finite element method. The two forming steps including the preforming process and the final forging process of H-shape forgings are analyzed using the self-developed code. The optimization results show that small grain size and homogeneous grain distribution can be achieved by controlling the shape of the preforming die. Samples of the same size as in the optimization are preformed and then forged to the desired H-shape forgings under the same deformation conditions as in the optimization. Micrographs in the symmetry section of samples show that the grain sizes of the forgings almost coincide with the optimization results.     

Influence of additives on the impact toughness of Al–10.8% Si near-eutectic cast alloys

This article investigates the effects of melt treatment and addition of alloying elements on the impact toughness of as-cast and heat-treated Al–10.8% Si near-eutectic alloys. Increasingly precise impact behaviors are discussed in the context of differentiating between initiation and propagation energies, including the ductility index, which is the ratio of the propagation to initiation energies; total energy as a useful measure is also discussed. Details concerning the evaluation of tensile properties are reported in a separate article [Mohamed AMA, Samuel FH, Samuel AM, Doty HW. Influence of additives on the microstructure and tensile properties of near-eutectic Al–10.8%Si cast alloy. Mater Des, in press]. The concentration of elements in the alloys was changed to the following range: Fe 0.5–1 wt%, Mn 0.5–1 wt%, Cu 2.25–3.25 wt%, and Mg 0.3–0.5 wt%, while the impact toughness upon artificial aging in a temperature range of 155–240 °C for 5 h was also investigated. The results indicate that the morphology of fibrous Si in Sr-modified alloys enhances toughness because of its profound effect on crack initiation and crack propagation resistance. The combined addition of modifier and grain refiner leads to a 33% increase in the impact strength compared to the untreated alloy. In alloys containing high levels of iron, such as the RF2 (1% Fe, 1% Mn) and RF4 (1% Fe, 0.5% Mn) alloys, the addition of iron leads to an increased precipitation of sludge or β-Fe platelets, respectively; these particles also act as crack initiation sites and reduce the impact properties noticeably. In alloys already containing high levels of copper, such as the RC2 (3.25% Cu, 0.3% Mg) and RC5(0.3.25% Cu, 0.5% Mg) alloys, increasing the copper level lowers the impact properties significantly, in view of the fact that the fracture behavior is now predominantly influenced by the Al₂Cu phase rather than by the Si particles. The average crack propagation speed of impact-tested samples shows a good inverse relationship to impact energy. Crack propagation speed can thus provide a qualitative estimation of the impact energy expected for special alloy conditions.     

Microstructural refinement of a cast hypereutectic Al–30Si alloy by friction stir processing

Hypereutectic Al-30 wt.% Si alloy was subjected to friction stir processing (FSP) to modify the cast microstructure. FSP reduces the size of undesirable coarse silicon particles, eliminates porosities, and homogenizes and refines the cast microstructure. This paper demonstrates the effect of two pass overlap friction stir processing on microstructural refinement of Al–30Si alloy, which delineates significant reduction in size and aspect ratio of silicon particles from average 200 to 2 µm and 4.93 to 1.75 µm respectively. The stir zone of two pass overlap FSP exhibits relatively homogeneous Si particle distribution. Increase in frequency of silicon particles less than 1 µm was also observed in two pass FSP stir zones. Hardness in stir zones was measured to be 75 Hv after first pass and the same changed to 85 Hv respectively after second pass. Further uniform microhardness was observed in the FSP stir zone which was not the case in as-cast Al–30Si microstructure.     

Microstructure and creep properties of a cast intermetallic Ti–46Al–2W–0.5Si alloy for gas turbine applications

The microstructure and creep properties including minimum creep rate, time to 1% creep deformation and creep fracture time of a cast TiAl-based alloy with nominal chemical composition Ti–46Al–2W–0.5Si (at.%) were investigated. The creep specimens were prepared from investment-cast plate and two large turbine blades. Constant load creep tests were performed in air at applied stresses ranging from 150 to 400 MPa in the temperature range 973–1073 K. The microstructure of the specimens is characterised by optical, scanning and transmission electron microscopy before and after creep deformation. The minimum creep rate is found to depend strongly on the applied stress and temperature. The power law stress exponent of minimum creep rate is n = 7.3 and the apparent activation energy for creep is Q_a = 427 ± 14 kJ/mol. The initial microstructure of the creep specimen is unstable. The ₂(Ti₃Al)-phase transforms to γ(TiAl)-phase and needle-like B2-precipitates during long-term creep testing at all testing temperatures. At lower applied stresses, the creep specimens fail by the growth and coalescence of cavities and small cracks formed along the γ/₂ interfaces. At the highest applied stresses, the specimens fail by nucleation and propagation of cracks.     

A study on the mechanical properties of cryorolled Al–Mg–Si alloy

The mechanical properties of a precipitation hardenable Al–Mg–Si alloy subjected to cryorolling and ageing treatments are reported in this present work. The severe strain induced during cryorolling of Al–Mg–Si alloys in the solid solutionised state produces ultrafine microstructures with improved mechanical properties such as strength and hardness. The improved strength and hardness of cryorolled alloys are due to the grain size effect and higher dislocation density. The ageing treatment of cryorolled Al–Mg–Si alloys has improved its strength and ductility significantly due to the precipitation hardening and grain coarsening mechanisms, respectively. The reduction in dimple size of cryorolled Al–Mg–Si alloy upon failure confirms the grain refinement and strain hardening mechanism operating in the severely deformed samples.     

Effect of the extrusion conditions on microstructure evolution of the extruded Al–Mg–Si–Cu alloy rods

Hot extrusion experiment was conducted using an Al–Mg–Si–Cu alloy and the effect of the extrusion conditions on microstructure and texture changes through the radial direction was investigated by using SEM/EBSP analysis method. In the surface layer where severe frictional shear deformation is predominant, the recrystallized 1 1 0//ED grains surrounded by high angle grain boundaries are formed in spite of the existence of some peripheral overcoarse grains. Strong 1 0 0//ED and 1 1 1//ED fiber textures evolve in the center where axisymmetric deformation along the extrusion direction is intensive. As the extrusion ratio increases, number of 1 1 1//ED grains remarkably decreases while the number of 1 0 0//ED grains apparently increases. It is also found that the 1 0 0//ED grains surrounded by low angle grain boundaries form orientation colonies in the center of the extruded rods.