A 0.6 V 10 bit 1 MS/s monotonic switching SAR ADC with common mode stabilizer in 0.13 μm CMOS

This paper presents a 0.6 V 10 bit successive approximation register （SAR） ADC design dedicated to the wireless sensor network application. It adopts a monotonic switching scheme in the DAC to save chip area and power consumption. The main drawback of the monotonic switching scheme is its large common mode shift and the associated comparator offset variation. Due to the limited headroom at the 0.6 V supply voltage, the conventional constant current biasing technique cannot be applied to the dynamic comparator. In this design, a common mode stabilizer is introduced to address this issue in low-voltage design. The effectiveness of this method is verified through both simulation and measurement results. Fabricated with 1P8M 0.13 μm CMOS technology, the proposed SAR ADC consumes 6.3 μW at 1 MS/s from a 0.6 V supply, and achieves 51.25 dB SNDR at the Nyquist frequency and FOM of 21 fJ/conversion-step. The core area is only 120 × 300 μm^2.     

应用于生物医疗的0.6-V 8.3-ENOB 异步时序逐次逼近型模数转换器

A microwatt asynchronous successive approximation register （SAR） analog-to-digital converter （ADC） is presented. The supply voltage of the SAR ADC is decreased to 0.6 V to fit the low voltage and low power require- ments of biomedical systems. The tail capacitor of the DAC array is reused for least significant bit conversion to decrease the total DAC capacitance thus reducing the power. Asynchronous control logic avoids the high frequency clock generator and further reduces the power consumption. The prototype ADC is fabricated with a standard 0.18 μm CMOS technology. Experimental results show that it achieves an ENOB of 8.3 bit at a 300-kS/s sampling rate. Very low power consumption of 3.04 μW is achieved, resulting in a figure of merit of 32 fJ/conv.-step.     

用于流水线ADC的频率自适应可编程MDAC电路

A programmable high precision multiplying DAC （MDAC） is proposed. The MDAC incorporates a frequency-current converter （FCC） to adjust the power versus sampling rate and a programmable operational am- plifier （POTA） to achieve the tradeoff between resolution and power of the MDAC, which makes the MDAC suitable for a 12 bit SHA-less pipelined ADC. The prototype of the proposed pipelined ADC is implemented in an SMIC CMOS 0.18 μm 1P6M process. Experimental results demonstrate that power of the proposed ADC varies from 15.4 mW （10 MHz） to 63 mW （100 MHz） while maintaining an SNDR of 60.5 to 63 dB at all sampling rates. The differential nonlinearity and integral nonlinearity without any calibration are no more than 2.2/-1 LSB and 1.6/-1.9 LSB, respectively.     

应用于人工关节无线监控系统的低功耗循环式ADC设计

This paper presents a low power cyclic analog-to-digital convertor （ADC） design for a wireless monitoring system for orthopedic implants. A two-stage cyclic structure including a single to differential converter, two multiplying DAC functional blocks （MDACs） and some comparators is adopted, which brings moderate speed and moderate resolution with low power consumption. The MDAC is implemented with the common switched capacitor method. The 1.5-bit stage greatly simplifies the design of the comparator. The operational amplifier is carefully op- timized both in schematic and layout for low power and offset. The prototype chip has been fabricated in a United Microelectronics Corporation （UMC） 0.18-μm 1P6M CMOS process. The core of the ADC occupies only 0.12 mm2. With a 304.7-Hz input and 4-kHz sampling rate, the measured peak SNDR and SFDR are 47.1 dB and 57.8 dBc respectively and its DNL and INL are 0.27 LSB and 0.3 LSB, respectively. The power consumption of the ADC is only 12.5 μW in normal working mode and less than 150 nW in sleep mode.     

A 130 nm CMOS low-power SAR ADC for wide-band communication systems

This paper presents a low power 9-bit 80 MS/s SAR ADC with comparator-sharing technique in 130 nm CMOS process. Compared to the conventional SAR ADC, the sampling phase is removed to reach the full efficiency of the comparator. Thus the conversion rate increases by about 20% and its sampling time is relaxed. The design does not use any static components to achieve a widely scalable conversion rate with a constant FOM. The floorplan of the capacitor network is custom-designed to suppress the gain mismatch between the two DACs. The ＇set-and- down＇ switching procedure and a novel binary-search error compensation scheme are utilized to further speed up the SA bit-cycling operation. A very fast logic controller is proposed with a delay time of only 90 ps. At 1.2 V supply and 80 MS/s the ADC achieves an SNDR of 51.4 dB and consumes 1.86 mW, resulting in an FOM of 76.6 fJ/conversion-step. The ADC core occupies an active area of only 0.089 mm2.     

An ll-bit 22-MS/s 0.6 mW SAR ADC with parasitic capacitance compensation

Abstract： This paper presents an l 1-bit 22-MS/s 0.6-mW successive approximation register （SAR） analog-to- digital converter （ADC） using SMIC 65-nm low leakage （LL） CMOS technology with a 1.2 V supply voltage. To reduce the total capacitance and core area the split capacitor architecture is adopted. But in high resolution ADCs the parasitic capacitance in the LSB-side would decrease the linearity of the ADC and it is hard to calibrate. This paper proposes a parasitic capacitance compensation technique to cancel the effect with no calibration circuits. Moreover, dynamic circuits are used to minimize the switching power of the digital logic and also can reduce the latency time. The prototype chip realized an 11-bit SAR ADC fabricated in SMIC 65-nm CMOS technology with a core area of 300 × 200 μm2. It shows a sampling rate of 22 MS/s and low power dissipation of 0.6 mW at a 1.2 V supply voltage. At low input frequency the signal-to-noise-and-distortion ratio （SNDR） is 59.3 dB and the spurious-free dynamic range is 72.2 dB. The peak figure-of-merit is 36.4 fJ/conversion-step.     

一个单通道10位160兆每秒的逐次逼近式模数转换器

This paper demonstrates a single-channel 10-bit 160 MS/s successive-approximation-register （SAR） analog-to-digital converter （ADC） in 65 nm CMOS process with a 1.2 V supply voltage. To achieve high speed, a new window-opening logic based on the asynchronous SAR algorithm is proposed to minimize the logic delay, and a partial set-and-down DAC with binary redundancy bits is presented to reduce the dynamic comparator offset and accelerate the DAC settling. Besides, a new bootstrapped switch with a pre-charge phase is adopted in the track and hold circuits to increase speed and reduce area. The presented ADC achieves 52.9 dB signal-to-noise distortion ratio and 65 dB spurious-free dynamic range measured with a 30 MHz input signal at 160 MHz clock. The power consumption is 9.5 mW and a core die area of 250 ×200 μm^2 is occupied.     

一种8-b 180KSPS的带有新颖的时域比较器且有效位数7.97的差分逐次逼近模数转换器

This paper presents a differential successive approximation register analog-to-digital converter (SAR ADC) with a novel time-domain comparator design for wireless sensor networks. The prototype chip has been implemented in the UMC 0.18-μ m 1P6M CMOS process. The proposed ADC achieves a peak ENOB of 7.98 at an input frequency of 39.7 kHz and sampling rate of 180 kHz. With the Nyquist input frequency, 68.49-dB SFDR, 7.97-ENOB is achieved. A simple quadrate layout is adopted to ease the routing complexity of the common-centroid symmetry layout. The ADC maintains a maximum differential nonlinearity of less than 0.08 LSB and integral nonlinearity less than 0.34 LSB by this type of layout.     

1-V电源65nm GP CMOS工艺下一款十位80MS/s 1.6mW逐次逼近型模数转换器

This paper presents a 10-bit 80-MS/s successive approximation register(SAR) analog-to-digital converter (ADC) suitable for integration in a system on a chip(SoC).By using the top-plate-sample switching scheme and a split capacitive array structure,the total capacitance is dramatically reduced which leads to low power and high speed.Since the split structure makes the capacitive array highly sensitive to parasitic capacitance,a three-row layout method is applied to the layout design.To overcome the charge leakage in the nanometer process,a special input stage is proposed in the comparator.As 80 MS/s sampling rate for a 10-bit SAR ADC results in around 1 GHz logic control clock,and a tunable clock generator is implemented.The prototype was fabricated in 65 nm 1P9M (one-poly-nine-metal) GP(general purpose) CMOS technology.Measurement results show a peak signal-to-noise and distortion ratio(SINAD) of 48.3 dB and 1.6 mW total power consumption with a figure of merit(FOM) of 94.8 fJ/conversion-step.     

Novel Sampling and Reconstruction Method for Non-Bandlimited Impulse Signals

To sample non-bandlimited impulse signals, an extremely high-sampling rate analog-todigital converters （ADC） is required. Such an ADC is very difficult to be implemented with present semiconductor technology. In this paper, a novel sampling and reconstruction method for impulse signals is proposed. The required sampling rate of the proposed method is close to the signal innovation rate, which is much lower than the Nyquist rate in conventional Shannon sampling theory. Analysis and simulation results show that the proposed method can achieve very good reconstruction performance in the presence of noise.     

An area-efficient 55 nm 10-bit 1-MS/s SAR ADC for battery voltage measurement

An area-efficient CMOS 1-MS/s 10-bit charge-redistribution SAR ADC for battery voltage measurement in a SoC chip is proposed. A new DAC architecture presents the benefits of a low power approach without applying the common mode voltage. The threshold inverter quantizer(TIQ)-based CMOS Inverter is used as a comparator in the ADC to avoid static power consumption which is attractive in battery-supply application. Sixteen level-up shifters aim at converting the ultra low core voltage control signals to the higher voltage level analog circuit in a 55 nm CMOS process. The whole ADC power consumption is 2.5 mW with a maximum input capacitance of 12 pF in the sampling mode. The active area of the proposed ADC is 0.0462 mm2 and it achieves the SFDR and ENOB of 65.6917 dB and 9.8726 bits respectively with an input frequency of 200 kHz at 1 MS/s sampling rate.     

An 8-bit 180-kS/s differential SAR ADC with a time-domain comparator and 7.97-ENOB

This paper presents a differential successive approximation register analog-to-digital converter(SAR ADC) with a novel time-domain comparator design for wireless sensor networks.The prototype chip has been implemented in the UMC 0.18-μm 1P6M CMOS process.The proposed ADC achieves a peak ENOB of 7.98 at an input frequency of 39.7 kHz and sampling rate of 180 kHz.With the Nyquist input frequency,68.49-dB SFDR,7.97-ENOB is achieved.A simple quadrate layout is adopted to ease the routing complexity of the co...     

一种SFDR为83.5dB的14位100兆流水线模数转换器

This paper demonstrates a 14-bit 100 MS/s CMOS pipelined analog-to-digital converter （ADC）. The nonlinearity model for bootstrapped switches is established to optimize the design parameters of bootstrapped switches, and the calculations based on this model agree well with the measurement results. In order to achieve high linearity, a gradient-mismatch cancelling technique is proposed, which eliminates the first order gradient error of sampling capacitors by combining arrangement of reference control signals and capacitor layout. Fabricated in a 0.18-μm CMOS technology, this ADC occupies 10.16-mm2 area. With statistics-based background calibration of finite opamp gain in the first stage, the ADC achieves 83.5-dB spurious free dynamic range and 63.7-dB signalto-noise-and distortion ratio respectively, and consumes 393 mW power with a supply voltage of 2 V.     

A Novel Receiver Architecture for DBF Antenna Array

The developments of the high speed analog to digital converters （ADC） and advanced digital signal processors （DSP） make the smart antenna with digital beamforming （DBF） a reality. In conventional M-elements array antenna system, each element has its own receiving channel and ADCs. In this paper, a novel smart antenna receiver with digital beamforming is proposed. The essential idea is to realize the digital beamforming receiver based on bandpass sampling of multiple distinct intermediate frequency （IF） signals. The proposed system reduces receiver hardware from M IF channels and 2M ADCs to one IF channel and one ADC using a heterodyne radio frequency （RF） circuitry and a multiple bandpass sampling digital receiver. In this scheme, the sampling rate of the ADC is much higher than the summation of the M times of the signal bandwidth. The local oscillator produces different local frequency for each RF channel The receiver architecture is presented in detail, and the simulation of bandpass sampling of multiple signals and digital down conversion to baseband is given. The principle analysis and simulation results indicate the effectiveness of the new proposed receiver.     

一种应用于RFID的低功耗温度传感器

This paper presents the design and implement of a CMOS smart temperature sensor,which consists of a low power analog front-end and a 12-bit low-power successive approximation register(SAR) analog-to-digital converter(ADC).The analog front-end generates a proportional-to-absolute-temperature(PTAT) voltage with MOSFET circuits operating in the sub-threshold region.A reference voltage is also generated and optimized in order to minimize the temperature error and the 12-bit SAR ADC is used to digitize the PTAT voltage.Using 0.18 m CMOS technology,measurement results show that the temperature error is0.69/C0.85 °C after one-point calibration over a temperature range of40 to 100 °C.Under a conversion speed of 1K samples/s,the power consumption is only 2.02 W while the chip area is 230225 m2,and it is suitable for RFID application.     

应用于碲锌镉探测器逐次逼近模数转换器基准电压的研究

An on-chip reference voltage has been designed in capacitor-resister hybrid SAR ADC for CZT detector with the TSMC 0.35 μ m 2P4M CMOS process. The voltage reference has a dynamic load since using variable capacitors and resistances, which need a large driving ability to deal with the current related to the time and sampling rate. Most of the previous articles about the reference for ADC present only the bandgap part for a low temperature coefficient and high PSRR. However, it is not enough and overall, it needs to consider the output driving ability. The proposed voltage reference is realized by the band-gap reference, voltage generator and output buffer. Apart from a low temperature coefficient and high PSRR, it has the features of a large driving ability and low power consumption. What is more, for CZT detectors application in space, a radiation-hardened design has been considered. The measurement results show that the output reference voltage of the buffer is 4.096 V. When the temperature varied from 0 to 80℃, the temperature coefficient is 12.2 ppm/℃. The PSRR was-70 dB@100 kHz. The drive current of the reference can reach up to 10 mA. The area of the voltage reference in the SAR ADC chip is only 449×614 μm². The total power consumption is only 1.092 mW.     

对高速比较器中复位场效应管的研究

A high-speed comparator design based on regeneration architecture, which can be used in a flash ADC, is presented.A threshold-limit-speed effect（TLSE） which limits the speed of the comparator was discovered and studied in detail.The size of the reset-MOSFET was optimized to resolve the TLSE and make the comparator work at the maximal speed.The results were confirmed by simulation and the corresponding circuit was realized in a flash ADC design in SMIC 0.18-μm CMOS technology.The test result shows that the comparator can work well at 2 GHz and can even work up to 2.8 GHz while the power dissipation is 3.2 mW.     

On the design of high-speed energy-efficient successive-approximation logic for asynchronous SAR ADCs

This paper analyzes the power consumption and delay mechanisms of the successive-approximation (SA) logic of a typical asynchronous SAR ADC, and provides strategies to reduce both of them. Following these strategies, a unique direct-pass SA logic is proposed based on a full-swing once-triggered DFF and a self-locking tri-state gate. The unnecessary internal switching power of a typical TSPC DFF, which is commonly used in the SA logic, is avoided. The delay of the ready detector as well as the sequencer is removed from the critical path. A prototype SAR ADC based on the proposed SA logic is fabricated in 130 nm CMOS. It achieves a peak SNDR of 56.3 dB at 1.2 V supply and 65 MS/s sampling rate, and has a total power consumption of 555 μ W, while the digital part consumes only 203 μ W.     

Current mode ADC design in a 0.5-μm CMOS process

This paper presents a pipelined current mode analog to digital converter（ADC） designed in a 0.5-μm CMOS process.Adopting the global and local bias scheme,the number of interconnect signal lines is reduced numerously,and the ADC exhibits the advantages of scalability and portability.Without using linear capacitance,this ADC can be implemented in a standard digital CMOS process;thus,it is suitable for applications in the system on one chip（SoC） design as an analogue IP.Simulations show that the proposed current mode ADC can operate in a wide supply range from 3 to 7 V and a wide quantization range from ±64 to ±256 μA.Adopting the histogram testing method,the ADC was tested in a 3.3 V supply voltage/±64 μA quantization range and a 5 V supply voltage/±256 μA quantization range,respectively.The results reveal that this ADC achieves a spurious free dynamic range of 61.46 dB,DNL/INL are-0.005 to ＋0.027 LSB/-0.1 to ＋0.2 LSB,respectively,under a 5 V supply voltage with a digital error correction technique.     

A power-efficient 12-bit analog-to-digital converter with a novel constant-resistance CMOS input sampling switch

Apower-efficient 12-bit40-MS/spipelineanalog-to-digitalconverter（ADC）implementedina0.13 μm CMOS technology is presented. A novel CMOS bootstrapping switch, which offers a constant on-resistance over the entire input signal range, is used at the sample-and-hold front-end to enhance the dynamic performance of the pipelined ADC. By implementing with 2.5-bit-per-stage and a simplified amplifier sharing architecture between two successive pipeline stages, a very competitive power consumption and small die area can be achieved. Meanwhile, the substrate-biasing-effect attenuated T-type switches are introduced to reduce the crosstalk between the two op- amp sharing successive stages. Moreover, a two-stage gain boosted recycling folded cascode （RFC） amplifier with hybrid frequency compensation is developed to further reduce the power consumption and maintain the ADC＇s performance simultaneously. The measured results imply that the ADC achieves a spurious-free dynamic range （SFDR） of 75.7 dB and a signal-to-noise-plus-distortion ratio （SNDR） of 62.74 dB with a 4.3 MHz input signal; the SNDR maintains over 58.25 dB for input signals up to 19.3MHz. The measured differential nonlinearity （DNL） and integral nonlinearity （INL） are -0.43 to ＋0.48 LSB and -1.62 to ＋ 1.89 LSB respectively. The prototype ADC consumes 28.4 mW under a 1.2-V nominal power supply and 40 MHz sampling rate, transferring to a figure- of-merit （FOM） of 0.63 pJ per conversion-step.